54LS169,DM54LS169A,DM74LS169A 54LS169 DM54LS169A DM74LS169A Synchronous 4-Bit Up/Down Binary Counter Literature Number: SNOS289A 54LS169/DM54LS169A/DM74LS169A Synchronous 4-Bit Up/Down Binary Counter General Description e counting up, and approximately equal to the low portion of the QA output when counting down. This low-level overflow carry pulse can be used to enable successively cascaded stages. Transitions at the enable P or T inputs are allowed regardless of the level of the clock input. All inputs are diode clamped to minimize transmission-line effects, thereby simplifying system design. This counter features a fully independent clock circuit. Changes at control inputs (enable P, enable T, load, up/ down), which modify the operating mode, have no effect until clocking occurs. The function of the counter (whether enabled, disabled, loading, or counting) will be dictated solely by the conditions meeting the stable setup and hold times. et This synchronous presettable counter features an internal carry look-ahead for cascading in high-speed counting applications. Synchronous operation is provided by having all flip-flops clocked simultaneously, so that the outputs all change at the same time when so instructed by the countenable inputs and internal gating. This mode of operation helps eliminate the output counting spikes that are normally associated with asynchronous (ripple clock) counters. A buffered clock input triggers the four master-slave flip-flops on the rising edge of the clock waveform. This counter is fully programmable; that is, the outputs may each be preset either high or low. The load input circuitry allows loading with the carry-enable output of cascaded counters. As loading is synchronous, setting up a low level at the load input disables the counter and causes the outputs to agree with the data inputs after the next clock pulse. The carry look-ahead circuitry permits cascading counters for n-bit synchronous applications without additional gating. Both count-enable inputs (P and T) must be low to count. The direction of the count is determined by the level of the up/down input. When the input is high, the counter counts up; when low, it counts down. Input T is fed forward to enable the carry outputs. The carry output thus enabled will produce a low-level output pulse with a duration approximately equal to the high portion of the QA output when Features Y Y Y Y bs ol Y Fully synchronous operation for counting and programming. Internal look-ahead for fast counting. Carry output for n-bit cascading. Fully independent clock circuit Alternate Military/Aerospace device (54LS169) is available. Contact a National Semiconductor Sales Office/Distributor for specifications. Connection Diagram O Dual-In-Line Package TL/F/6401 - 1 Order Number 54LS169DMQB, 54LS169FMQB, 54LS169LMQB, DM54LS169AJ, DM54LS169AW, DM74LS169AM or DM74LS169AN See NS Package Number E20A, J16A, M16A, N16E or W16A C1995 National Semiconductor Corporation TL/F/6401 RRD-B30M105/Printed in U. S. A. 54LS169/DM54LS169A/DM74LS169A Synchronous 4-Bit Up/Down Binary Counter June 1989 Absolute Maximum Ratings (Note) Note: The ``Absolute Maximum Ratings'' are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the ``Electrical Characteristics'' table are not guaranteed at the absolute maximum ratings. The ``Recommended Operating Conditions'' table will define the conditions for actual device operation. If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distributors for availability and specifications. Supply Voltage 7V Input Voltage 7V Operating Free Air Temperature Range b 55 C to a 125 C DM54LS and 54LS DM74LS 0 C to a 70 C Storage Temperature Range b 65 C to a 150 C Recommended Operating Conditions DM54LS169A Parameter DM74LS169A Nom Max Min Nom Max 4.5 5 5.5 4.75 5 5.25 V 0.7 0.8 V b 0.4 mA VCC Supply Voltage VIH High Level Input Voltage VIL Low Level Input Voltage IOH High Level Output Current b 0.4 IOL Low Level Output Current 4 fCLK Clock Frequency (Note 1) 2 25 20 0 Clock Pulse Width (Note 3) 25 tSU Setup Time (Note 3) Data 20 Enable T or P 20 Load 25 U/D 30 Free Air Operating Temperature 8 mA 0 25 MHz 0 20 MHz 25 ns 20 20 ns 0 25 30 0 bs ol TA V et Clock Frequency (Note 2) Hold Time (Note 3) 2 0 tW tH Units Min e Symbol b 55 125 0 ns 70 C Note 1: CL e 15 pF, RL e 2 kX, TA e 25 C and VCC e 5V. Note 2: CL e 50 pF, RL e 2 kX, TA e 25 C and VCC e 5V. Note 3: TA e 25 C and VCC e 5V. Electrical Characteristics over recommended operating free air temperature range (unless otherwise noted) Symbol Parameter VI Input Clamp Voltage VOH High Level Output Voltage VCC e Min, II e b18 mA VCC e Min, IOH e Max VIL e Max, VIH e Min Low Level Output Voltage VCC e Min, IOL e Max VIL e Max, VIH e Min II IIH IIL IOS ICC Typ (Note 4) DM54 2.5 3.4 DM74 2.7 3.4 Max Units b 1.5 V V DM54 0.25 DM74 0.35 0.5 IOL e 4 mA, VCC e Min DM74 0.25 0.4 Input Current @ Max Input Voltage VCC e Max VI e 7V Enable T 0.2 Others 0.1 High Level Input Current VCC e Max VI e 2.7V Enable T 40 Others 20 Low Level Input Current VCC e Max VI e 0.4V Enable T b 0.8 Others b 0.4 Short Circuit Output Current VCC e Max (Note 5) DM54 b 20 b 100 DM74 b 20 b 100 Supply Current VCC e Max (Note 6) O VOL Min Conditions 20 0.4 34 Note 4: All typicals are at VCC e 5V and TA e 25 C. Note 5: Not more than one output should be shorted at a time, and the duration should not exceed one second. Note 6: ICC is measured after a momentary 4.5V, then ground, is applied to the CLOCK with all other inputs grounded and all the outputs open. 2 V mA mA mA mA mA Switching Characteristics at VCC e 5V and TA e 25 C (See Section 1 for Test Waveforms and Output Load) RL e 2 kX Symbol Parameter From (Input) To (Output) CL e 15 pF Min Max CL e 50 pF Min Units Max fMAX Maximum Clock Frequency tPLH Propagation Delay Time Low to High Level Output Clock to Ripple Carry 35 39 ns tPHL Propagation Delay Time High to Low Level Output Clock to Ripple Carry 35 44 ns tPLH Propagation Delay Time Low to High Level Output Clock to Any Q 20 24 ns tPHL Propagation Delay Time High to Low Level Output Clock to Any Q 23 32 ns tPLH Propagation Delay Time Low to High Level Output Enable T to Ripple Carry 18 24 ns tPHL Propagation Delay Time High to Low Level Output Enable T to Ripple Carry tPLH Propagation Delay Time Low to High Level Output Up/Down to Ripple Carry (Note 1) tPHL Propagation Delay Time High to Low Level Output Up/Down to Ripple Carry (Note 1) 20 MHz e 25 28 ns 25 30 ns et 18 29 38 ns O bs ol Note 1: The propagation delay from UP/DOWN to RIPPLE CARRY must be measured with the counter at either a minimum or a maximum count. As the logic level of the up/down input is changed, the ripple carry output will follow. If the count is minimum, the ripple carry output transition will be in phase. If the count is maximum, the ripple carry output will be out of phase. 3 Logic Diagram O bs ol et e LS169A Binary Counter TL/F/6401 - 2 4 Timing Diagram O bs ol et e LS169A Binary Counters Typical Load, Count, and Inhibit Sequences 5 TL/F/6401 - 3 et e Physical Dimensions inches (millimeters) O bs ol Ceramic Leadless Chip Carrier Package (E) Order Number 54LS169LMQB NS Package Number E20A 16-Lead Ceramic Dual-In-Line Package (J) Order Number 54LS169DMQB or DM54LS169AJ NS Package Number J16A 6 et e Physical Dimensions inches (millimeters) (Continued) O bs ol 16-Lead Small Outline Molded Package (M) Order Number DM74LS169AM NS Package Number M16A 16-Lead Molded Dual-In-Line Package (N) Order Number DM74LS169AN NS Package Number N16E 7 e et 16-Lead Ceramic Flat Package (W) Order Number 54LS169FMQB or DM54LS169AW NS Package Number W16A bs ol 54LS169/DM54LS169A/DM74LS169A Synchronous 4-Bit Up/Down Binary Counter Physical Dimensions inches (millimeters) (Continued) LIFE SUPPORT POLICY O NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation 1111 West Bardin Road Arlington, TX 76017 Tel: 1(800) 272-9959 Fax: 1(800) 737-7018 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Europe Fax: (a49) 0-180-530 85 86 Email: cnjwge @ tevm2.nsc.com Deutsch Tel: (a49) 0-180-530 85 85 English Tel: (a49) 0-180-532 78 32 Fran3ais Tel: (a49) 0-180-532 93 58 Italiano Tel: (a49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd. 13th Floor, Straight Block, Ocean Centre, 5 Canton Rd. Tsimshatsui, Kowloon Hong Kong Tel: (852) 2737-1600 Fax: (852) 2736-9960 National Semiconductor Japan Ltd. Tel: 81-043-299-2309 Fax: 81-043-299-2408 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated