© 2000 IXYS All rights reserved 1 - 3
IFRMS = 2x 480 A
IFAVM = 2x 305 A
VRRM = 800-2200 V
Symbol Test Conditions Characteristic Values
IRRM TVJ = TVJM; VR = VRRM 40 mA
VFIF = 600 A; TVJ = 25°C 1.2 V
VT0 For power-loss calculations only 0.75 V
rTTVJ = TVJM 0.63 mW
RthJC per diode; DC current 0.129 K/W
per module other values 0.065 K/W
RthJK per diode; DC current see Fig. 6/7 0.169 K/W
per module 0.0845 K/W
QSTVJ = 125°C, IF = 400 A; -di/dt = 50 A/ms 760 mC
IRM 275 A
dSCreepage distance on surface 12.7 mm
dAStrike distance through air 9.6 mm
aMaximum allowable acceleration 50 m/s2
VRSM VRRM Type
VV
900 800 MDD 310-08N1
1300 1200 MDD 310-12N1
1500 1400 MDD 310-14N1
1700 1600 MDD 310-16N1
2100 2000 MDD 310-20N1
2300 2200 MDD 310-22N1
Symbol Test Conditions Maximum Ratings
IFRMS TVJ = TVJM 480 A
IFAVM TC = 100°C; 180° sine 305 A
IFSM TVJ = 45°C; t = 10 ms (50 Hz), sine 11 500 A
VR = 0 t = 8.3 ms (60 Hz), sine 12 200 A
TVJ = TVJM t = 10 ms (50 Hz), sine 9 600 A
VR = 0 t = 8.3 ms (60 Hz), sine 10 200 A
òi2dt TVJ = 45°C t = 10 ms (50 Hz), sine 662 000 A2s
VR = 0 t = 8.3 ms (60 Hz), sine 620 000 A2s
TVJ = TVJM t = 10 ms (50 Hz), sine 460 000 A2s
VR = 0 t = 8.3 ms (60 Hz), sine 430 000 A2s
TVJ -40...+150 °C
TVJM 150 °C
Tstg -40...+125 °C
VISOL 50/60 Hz, RMS t = 1 min 3000 V~
IISOL £ 1 mA t = 1 s 3600 V~
MdMounting torque (M5) 2.5-5/22-44 Nm/lb.in.
Terminal connection torque (M8) 12-15/106-132 Nm/lb.in.
Weight Typical including screws 320 g
MDD 310
High Power
Diode Modules
312
1
3
2
Data according to IEC 60747 and refer to a single diode unless otherwise stated.
IXYS reserves the right to change limits, test conditions and dimensions
Features
●Direct copper bonded Al2O3 -ceramic
base plate
●Planar passivated chips
●Isolation voltage 3600 V~
●UL registered, E 72873
Applications
●Supplies for DC power equipment
●DC supply for PWM inverter
●Field supply for DC motors
●Battery DC power supplies
Advantages
●Space and weight savings
●Simple mounting
●Improved temperature and power
cycling
●Reduced protection circuits
Threaded spacer for higher Anode/Cathode
construction: Type ZY 250, material brass
14
Dimensions in mm (1 mm = 0.0394")
20 12
936
http://store.iiic.cc/
© 2000 IXYS All rights reserved 2 - 3
MDD 310
Fig. 1 Surge overload current
IFSM: Crest value, t: duration Fig. 2 òi2dt versus time (1-10 ms) Fig. 2a Maximum forward current
at case temperature
Fig. 3 Power dissipation versus
forward current and ambient
temperature (per diode)
Fig. 4 Single phase rectifier bridge:
Power dissipation versus direct
output current and ambient
temperature
R = resistive load
L = inductive load
http://store.iiic.cc/
© 2000 IXYS All rights reserved 3 - 3
Fig. 5 Three phase rectifier bridge:
Power dissipation versus direct
output current and ambient
temperature
MDD 310
Fig. 6 Transient thermal impedance
junction to case (per diode)
Fig. 7 Transient thermal impedance
junction to heatsink (per diode)
RthJK for various conduction angles d:
d RthJK (K/W)
DC 0.169
180°0.171
120°0.172
60°0.172
30°0.173
Constants for ZthJK calculation:
iR
thi (K/W) ti (s)
1 0.0035 0.0099
2 0.0165 0.168
3 0.1091 0.456
4 0.04 1.36
RthJC for various conduction angles d:
d RthJC (K/W)
DC 0.129
180°0.131
120°0.132
60°0.132
30°0.133
Constants for ZthJC calculation:
iR
thi (K/W) ti (s)
1 0.0035 0.0099
2 0.0165 0.168
3 0.1091 0.456
10-3 10-2 10-1 100101102
0.00
0.05
0.10
0.15
0.20
10-3 10-2 10-1 100101102
0.00
0.05
0.10
0.15
ts
ZthJK
K/W
ts
ZthJC
K/W
30°
DC
0
0
30°
DC
838
http://store.iiic.cc/
