EVALUATION KIT AVAILABLE MAX8614A/MAX8614B Dual-Output (+ and -) DC-DC Converters for CCD General Description The MAX8614A/MAX8614B dual-output step-up DC-DC converters generate both a positive and negative supply voltage that are each independently regulated. The positive output delivers up to 50mA while the inverter supplies up to 100mA with input voltages between 2.7V and 5.5V. The MAX8614A/MAX8614B are ideal for powering CCD imaging devices and displays in digital cameras and other portable equipment. The MAX8614A/MAX8614B generate an adjustable positive output voltage up to +24V and a negative output down to 16V below the input voltage. The MAX8614B has a higher current limit than the MAX8614A. Both devices operate at a fixed 1MHz frequency to ease noise filtering in sensitive applications and to reduce external component size. Additional features include pin-selectable power-on sequencing for use with a wide variety of CCDs, True ShutdownTM, overload protection, fault flag, and internal soft-start with controlled inrush current. The MAX8614A/MAX8614B are available in a spacesaving 3mm x 3mm, 14-pin TDFN package and are specified over the -40C to +85C extended temperature range. Applications CCD Bias Supplies and OLED Displays Digital Cameras Features o o o o o o o o o o o o Dual Output Voltages (+ and -) Adjustable Up to +24V and Down to -10V at 5.5VIN Output Short/Overload Protection True Shutdown on Both Outputs Controlled Inrush Current During Soft-Start Selectable Power-On Sequencing Up to 90% Efficiency 1A Shutdown Current 1MHz Fixed-Frequency PWM Operation Fault-Condition Flag Thermal Shutdown Small, 3mm x 3mm, 14-Pin TDFN Package Ordering Information TEMP RANGE PINTOP PACKAGE MARK ILIM BST/ INV MAX8614AETD+ -40C to +85C 14 TDFN ABG 0.44/ 0.33 MAX8614BETD+ -40C to +85C 14 TDFN ABH 0.8/ 0.75 MAX8614BETD/V+ -40C to +85C 14 TDFN AKT 0.8/ 0.75 PART +Denotes a lead(Pb)-free/RoHS-compliant package. /V denotes an automotive qualified part that conforms to AEC-Q100. Camcorders and Portable Multimedia Typical Operating Circuit PDAs and Smartphones INPUT (2.7V TO 5.5V) True Shutdown is a trademark of Maxim Integrated Products, Inc. VCC ONINV Pin Configuration LXN VINV -7.5V VCC PVP PGND LXP ONINV SEQ TOP VIEW LXN ONBST 14 13 12 11 10 9 8 AVCC MAX8614A MAX8614B FBN PVP REF MAX8614A MAX8614B REF AVCC SEQ LXP + FLT 6 7 FBP 5 GND 4 REF 3 AVCC 2 FBN ONBST 1 VBST +15V FLT GND PGND FBP TDFN For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maximintegrated.com. 19-4014; Rev 2; 6/14 MAX8614A/MAX8614B Dual-Output (+ and -) DC-DC Converters for CCD ABSOLUTE MAXIMUM RATINGS VCC, AVCC to GND ..................................................-0.3V to +6V LXN to VCC .............................................................-18V to +0.3V LXP to PGND ..........................................................-0.3V to +33V REF, ONINV, ONBST, SEQ, FBN, FBP FLT to GND .........................................-0.3V to (AVCC + 0.3)V PVP to GND ................................................-0.3V to (VCC + 0.3)V AVCC to VCC .........................................................-0.3V to +0.3V PGND to GND .......................................................-0.3V to +0.3V Continuous Power Dissipation (TA = +70C Multilayer Board) 14-Pin 3mm x 3mm TDFN (derate 18.2mW/C above TA = +70C) ............................................................1454.4mW Operating Temperature Range ...........................-40C to +85C Junction Temperature ......................................................+150C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) .................................+300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VCC = VAVCC = VONINV = VONBST = 3.6V, PGND = SEQ = GND, C6 = 0.22F, C1 = 2.2F, C2 = 4.7F, Figure 1, TA = 0C to +85C, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER CONDITIONS MIN AVCC and VCC Voltage Range (Note 1) 2.7 UVLO Threshold VCC rising 2.42 UVLO Hysteresis LXP Current Limit LXP Short-Circuit Current Limit LXN Current Limit MAX UNITS 5.5 V 2.55 2.66 25 Step-Up Output-Voltage Adjust Range Inverter Output-Voltage Adjust Range TYP VINV - VCC (Note 2) V mV VAVCC 24 V -16 0 V MAX8614B 0.7 0.8 0.9 MAX8614A 0.34 0.44 0.52 MAX8614B 0.90 1.05 1.20 MAX8614A 0.52 0.61 0.70 MAX8614B 0.65 0.75 0.85 MAX8614A 0.28 0.33 0.38 1.1 LXN On-Resistance VCC = 3.6V 0.6 LXP On-Resistance VCC = 3.6V 0.625 PVP On-Resistance VCC = 3.6V Maximum Duty Cycle Step-up and inverter 0.15 82 A A A 0.3 90 % IAVCC 0.75 1.4 I VCC 2 3 IAVCC 400 800 I VCC TA = +25C TA = +85C 8 0.1 0.1 15 5 FBP Line Regulation VCC = 2.7V to 5.5V -20 mV/D FBN Line Regulation VCC = 2.7V to 5.5V 20 mV/ (D - 0.5) Quiescent Current (Switching, No Load) Quiescent Current (No Switching, No Load) Shutdown Supply Current 2 mA A A Maxim Integrated MAX8614A/MAX8614B Dual-Output (+ and -) DC-DC Converters for CCD ELECTRICAL CHARACTERISTICS (continued) (VCC = VAVCC = VONINV = VONBST = 3.6V, PGND = SEQ = GND, C6 = 0.22F, C1 = 2.2F, C2 = 4.7F, Figure 1, TA = 0C to +85C, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER FBP Load Regulation FBN Load Regulation CONDITIONS TYP -15 ILXN = I ILIMMIN, MAX8614B 17.5 ILXN = I ILIMMIN, MAX8614A 65 Oscillator Frequency Soft-Start Interval MIN ILXP = I ILIMMIN, MAX8614B ILXP = I ILIMMIN, MAX8614A MAX mV/A -35 0.93 Step-up and inverter Overload-Protection Fault Delay 1 UNITS mV/A 1.07 MHz 10 ms 100 ms FBP, FBN, REFERENCE REF Output Voltage No load REF Load Regulation REF Line Regulation 0A < IREF < 50A 3.3V < VAVCC < 5.5V FBP Threshold Voltage No load FBN Threshold Voltage No load 1.24 1.25 1.26 10 0.995 TA = +25C FBP Input Leakage Current VFBP =1.025V FBN Input Leakage Current FBN = -10mV LXN Input Leakage Current VLXN = -12V LXP Input Leakage Current VLXP = 23V PVP Input Leakage Current VPVP = 0V FLT Input Leakage Current VFLT = 3.6V FLT Input Resistance Fault mode, TA = +25C TA = +25C mV +10 +50 +5 -50 +5 +50 +5 -5 +0.1 +5 +0.1 -5 +0.1 +5 +0.1 -5 TA = +85C TA = +25C V 0 TA = +85C TA = +25C mV +5 TA = +85C TA = +25C 5 1.025 -10 TA = +85C TA = +25C 2 1.010 -50 TA = +85C +0.1 +5 +0.1 -1 TA = +85C V mV +0.1 +1 +0.1 10 20 nA nA A A A A ONINV, ONBST, SEQ LOGIC INPUTS Logic-Low Input 2.7V < VAVCC < 5.5V Logic-High Input 2.7V < VAVCC < 5.5V Bias Current TA = +25C Maxim Integrated 0.5 1.6 V V 0.1 1 A 3 MAX8614A/MAX8614B Dual-Output (+ and -) DC-DC Converters for CCD ELECTRICAL CHARACTERISTICS (VCC = VAVCC = VONINV = VONBST = VEN = 3.6V, PGND = SEQ = GND, C6 = 0.22F, C1 = 2.2F, C2 = 6.7F, Figure 1, TA = -40C to +85C, unless otherwise noted.) (Note 3) PARAMETER AVCC = VCC Voltage Range UVLO Threshold CONDITIONS (Note 1) VCC rising Step-Up Output Voltage Adjust Range Inverter Output Voltage Adjust Range LXP Current Limit LXP Short-Circuit Current Limit LXN Current Limit VINV - VCC (Note 2) MIN MAX UNITS 3 TYP 5.5 V V 2.42 2.82 VAVCC 24 V -16 0 V MAX8614B 0.7 0.9 MAX8614A 0.34 0.52 MAX8614B 0.9 1.2 MAX8614A 0.52 0.70 MAX8614B 0.65 0.85 MAX8614A 0.28 0.38 LXN On-Resistance VCC = 3.6V 1.1 PVP On-Resistance VCC = 3.6V 0.3 Maximum Duty Cycle Step-up and inverter Quiescent Current (Switching, No Load) Quiescent Current (No Switching, No Load) 82 A A % IAVCC 1.4 I VCC 3 IAVCC 800 I VCC 15 Oscillator Frequency A 0.93 1.07 mA A MHz FBP, FBN, REFERENCE REF Output Voltage No load 1.235 1.260 V FBP Threshold Voltage No load 0.995 1.025 V FBN Threshold Voltage No load -10 +10 mV 0.5 V ONINV, ONBST SEQ LOGIC INPUTS Logic-Low Input Logic-High Input 2.7V < VAVCC < 5.5V 2.7V < VAVCC < 5.5V 1.6 V Note 1: Output current and on-resistance are specified at 3.6V input voltage. The IC operates to 2.7V with reduced performance. Note 2: The specified maximum negative output voltage is referred to VCC, and not to GND. With VCC = 3.3V, the maximum negative output is then -12.7V. Note 3: Specifications to -40C are guaranteed by design, not production tested. 4 Maxim Integrated MAX8614A/MAX8614B Dual-Output (+ and -) DC-DC Converters for CCD Typical Operating Characteristics (TA = +25C, VCC = VAVCC = 3.6V, SEQ = GND, Figure 1, unless otherwise noted.) MAXIMUM OUTPUT CURRENT vs. INPUT VOLTAGE VOUT = 15V 150 100 50 80 70 200 150 VINV = -7.5V 100 5.0 3.0 POSITIVE OUTPUT EFFICIENCY vs. OUTPUT CURRENT 0.1 MAX8614A/B toc05 100 40 70 60 VCC = 4.2V 50 VCC = 5V 40 60 40 30 20 20 20 10 10 1 10 OUTPUT CURRENT (mA) 100 0.1 1 10 OUTPUT CURRENT (mA) 0.1 100 100 MAX8614A/B toc07 VCC = 5V 80 80 70 60 VCC = 3V 50 VCC = 4.2V VCC = 3.6V 40 30 EFFICIENCY (%) EFFICIENCY (%) VCC = 5V 90 70 100 VCC = 4.2V 60 VCC = 3V 50 VCC = 3.6V 40 30 20 20 BOTH OUTPUTS LOADED EQUALLY L1 = 2.2H, C1 = 2.2F, L2 = 4.7H, C2 = 4.7F 0 10 BOTH OUTPUTS LOADED EQUALLY L1 = 10H, C1 = 10F, L2 = 10H, C2 = 10F 0 0.1 Maxim Integrated 1 10 OUTPUT CURRENT (mA) OUTPUT EFFICIENCY vs. OUTPUT CURRENT 100 10 L = 10H, C = 10F 0 OUTPUT EFFICIENCY vs. OUTPUT CURRENT 90 VCC = 5V 10 L = 4.7H, C = 4.7F 0 0.1 VCC = 4.2V 50 30 L = 10H, C = 10F VCC = 3V 80 30 0 100 VCC = 3.6V 90 EFFICIENCY (%) VCC = 4.2V 1 10 OUTPUT CURRENT (mA) NEGATIVE OUTPUT EFFICIENCY vs. OUTPUT CURRENT 70 60 VCC = 3V 5.5 VCC = 3V 80 VCC = 3.6V 50 5.0 VCC = 3.6V 90 EFFICIENCY (%) EFFICIENCY (%) 100 MAX8614A/B toc04 80 70 3.5 4.0 4.5 INPUT VOLTAGE (V) NEGATIVE OUTPUT EFFICIENCY vs. OUTPUT CURRENT VCC = 5V 90 L = 2.2H, C = 2.2F 0 2.5 5.5 VCC = 4.2V 40 10 3.5 4.0 4.5 INPUT VOLTAGE (V) 100 VCC = 3.6V 20 50 0 3.0 VCC = 3V 50 30 VINV = -10V VOUT = 20V 0 2.5 60 MAX8614A/B toc06 200 VCC = 5V 90 MAX8614A/B toc08 250 VINV = -5V 250 EFFICIENCY (%) VOUT = 10V MAXIMUM OUTPUT CURRENT (mA) . 300 100 MAX8614A/B toc02 300 MAX8614A/B toc01 MAXIMUM OUTPUT CURRENT (mA) 350 POSITIVE OUTPUT EFFICIENCY vs. OUTPUT CURRENT MAX8614A/B toc03 MAXIMUM OUTPUT CURRENT vs. INPUT VOLTAGE 1 10 OUTPUT CURRENT (mA) 100 0.1 1 10 100 OUTPUT CURRENT (mA) 1000 5 MAX8614A/MAX8614B Dual-Output (+ and -) DC-DC Converters for CCD Typical Operating Characteristics (continued) (TA = +25C, VCC = VAVCC = 3.6V, SEQ = GND, Figure 1, unless otherwise noted.) VCC = 5V -0.5 VCC = 4.2V -1.0 -1.5 -2.0 VCC = 3V -2.5 VCC = 3.6V -3.0 0 VOUT- = -7.5V CHANGE IN OUTPUT VOLTAGE (%) MAX8614A/B toc09 CHANGE IN OUTPUT VOLTAGE (%) 0 -0.5 VIN = 4.2V -1.5 -2.0 -2.5 VIN = 3V -3.0 VIN = 3.6V -3.5 -3.5 0 25 50 75 100 LOAD CURRENT (mA) 125 0 150 NO-LOAD SUPPLY CURRENT vs. INPUT VOLTAGE 50 75 100 OUTPUT CURRENT (mA) 125 MAX8614A/B toc12 MAX8614A/B toc11 900 800 700 25 SOFT-START WAVEFORMS 1000 SUPPLY CURRENT (A) VIN = 5V -1.0 VONINV VONBST SEQ = GND 5V/div 0V AVCC 10V/div VBST 600 0V 500 400 5V/div VINV 300 VCC 200 IIN 100 100mA/div 0V 0 2.5 3.0 3.5 4.0 4.5 INPUT VOLTAGE (V) 5.0 4ms/div 5.5 LINE TRANSIENT SOFT-START WAVEFORMS MAX8614A/B toc14 MAX8614A/B toc13 VONINV VONBST SEQ = AVCC 5V/div 0V 50mV/div AC-COUPLED VBST 10V/div VBST 0V 5V/div VINV VIN 3.5V TO 4.5V TO 3.5V 3.5V 50mV/div AC-COUPLED VINV IIN 100mA/div 0V 4ms/div 6 MAX8614A/B toc10 CHANGE IN OUTPUT VOLTAGE vs. OUTPUT CURRENT (NEGATIVE OUTPUT) CHANGE IN OUTPUT VOLTAGE vs. LOAD CURRENT (POSITIVE OUTPUT) 40s/div Maxim Integrated MAX8614A/MAX8614B Dual-Output (+ and -) DC-DC Converters for CCD Typical Operating Characteristics (continued) (TA = +25C, VCC = VAVCC = 3.6V, SEQ = GND, Figure 1, unless otherwise noted.) LOAD TRANSIENT (POSITIVE OUTPUT) LOAD TRANSIENT (NEGATIVE OUTPUT) MAX8614A/B toc15 MAX8614A/B toc16 20mV/div AC-COUPLED VINV 100mV/div AC-COUPLED VBST IBST 20mA/div 20mA TO 50mA TO 20mA VBST 50mV/div AC-COUPLED VINV 100mV/div AC-COUPLED IINV 0V 50mA/div 20mA TO 100mA TO 20mA 4s/div SWITCHING WAVEFORMS (POSITIVE OUTPUT) SWITCHING WAVEFORMS (POSITIVE OUTPUT) MAX8614A/B toc18 MAX8614A/B toc17 VBST 50mV/div AC-COUPLED VBST 50mV/div AC-COUPLED 10V/div 10V/div VLX 0V ILX 500mA/div 0A VLX 0V 500mA/div ILX 0A IBST = 50mA IBST = 20mA 400ns/div 400ns/div SWITCHING WAVEFORMS (NEGATIVE OUTPUT) MAX8614A/B toc19 VINV SWITCHING WAVEFORMS (NEGATIVE OUTPUT) MAX8614A/B toc20 50mV/div AC-COUPLED VINV 50mV/div AC-COUPLED 10V/div 0V VLX 500mA/div 0A ILX IINV = 20mA 10V/div 0V VLX 500mA/div 0A ILX IINV = 100mA 400ns/div Maxim Integrated 0V 4s/div 400ns/div 7 MAX8614A/MAX8614B Dual-Output (+ and -) DC-DC Converters for CCD Typical Operating Characteristics (continued) (TA = +25C, VCC = VAVCC = 3.6V, SEQ = GND, Figure 1, unless otherwise noted.) SWITCHING FREQUENCY vs. TEMPERATURE REFERENCE VOLTAGE vs. TEMPERATURE 1.005 1.004 FREQUENCY (kHz) 1.2480 MAX8614A/B toc22 1.2485 REFERENCE VOLTAGE (V) 1.006 MAX8614A/B toc21 1.2490 1.2475 1.2470 1.2465 1.2460 VINV = -7.5V IOUT = 100mA 1.003 1.002 1.001 1.000 VBST = +15V IOUT = 50mA 0.999 0.998 1.2455 0.997 0.996 1.2450 -40 -15 10 35 TEMPERATURE (C) 60 -40 85 -15 10 35 TEMPERATURE (C) 60 85 Pin Description 8 PIN NAME FUNCTION 1 ONBST Enable Logic Input. Connect ONBST to AVCC for automatic startup of the step-up converter, or use ONBST as an independent control of the step-up converter. 2 FBN Negative Output Feedback Input. Connect a resistor-divider between the negative output and REF with the center to FBN to set the negative output voltage. 3 AVCC Bias Supply. AVCC powers the IC. AVCC must be connected to VCC. 4 REF 1.25V Reference Voltage Output. Bypass with a 0.22F ceramic capacitor to GND. 5 GND Ground. Connect GND to PGND with a short trace. 6 FLT Fault Open-Drain Output. Connect a 100k resistor from FLT to AVCC. FLT is active low during a fault event and is high impedance in shutdown. 7 FBP Positive Output-Voltage Feedback Input. Connect a resistor-divider between the positive output and GND with the center to FBP to set the positive output voltage. FBP is high impedance in shutdown. 8 SEQ Sequence Logic Input. When SEQ = low, power-on sequence can be independently controlled by ONBST and ONINV. When SEQ = high, the positive output powers up before the negative output. 9 ONINV Enable Logic Input. Connect ONINV to AVCC for automatic startup of the inverter, or use ONINV as an independent control of the inverter. 10 LXP 11 PGND Positive Output Switching Inductor Node. LXP is high impedance in shutdown. 12 PVP True-Shutdown Load Disconnect Switch. Connect one side of the inductor to PVP and the other side to LXP. PVP is high impedance in shutdown. 13 VCC Power Input Supply. VCC supplies power for the step-up and inverting DC-DC converters. VCC must be connected to AVCC. 14 LXN -- EP Power Ground. Connect PGND to GND with a short trace. Negative Output Switching Inductor Node. LXN is high impedance in shutdown. Exposed Pad. Connect exposed pad to ground. Maxim Integrated MAX8614A/MAX8614B Dual-Output (+ and -) DC-DC Converters for CCD Functional Diagram ERROR AMPLIFIER MAX8614A MAX8614B PWM COMPARATOR VCC INVERTER CONTROL LOGIC LXN INVERTER CURRENT SENSE FBN ONBST ONINV FLT 1.01V BIAS AND CONTROL BLOCK REF REFERENCE 1.25V SOFT-START SEQ AVCC 1MHz OSCILLATOR PVP ERROR AMPLIFIER PWM COMPARATOR LXP STEP-UP CONTROL LOGIC PGND STEP-UP CURRENT SENSE FBP GND Detailed Description The MAX8614A/MAX8614B generate both a positive and negative output voltage by combining a step-up and an inverting DC-DC converter on one IC. Both the step-up converter and the inverter share a common clock. Each output is independently regulated. Each output is separately controlled by a pulse-widthmodulated (PWM) current-mode regulator. This allows the converters to operate at a fixed frequency (1MHz) for use in noise-sensitive applications. The 1MHz switching rate allows for small external components. Both converters are internally compensated and are optimized for fast transient response (see the Load Transient/Voltage Positioning section). Maxim Integrated Step-Up Converter The step-up converter generates a positive output voltage up to 24V. An internal power switch, internal True-Shutdown load switch (PVP), and external catch diode allow conversion efficiencies as high as 90%. The internal load switch disconnects the battery from the load by opening the battery connection to the inductor, providing True Shutdown. The internal load switch stays on at all times during normal operation. The load switch is used in the control scheme for the converter and cannot be bypassed. 9 MAX8614A/MAX8614B Dual-Output (+ and -) DC-DC Converters for CCD Inverter The inverter generates output voltages down to -16V below VCC. An internal power switch and external catch diode allow conversion efficiencies as high as 85%. Control Scheme Both converters use a fixed-frequency, PWM currentmode control scheme. The heart of the current-mode PWM controllers is a comparator that compares the error-amp voltage-feedback signal against the sum of the amplified current-sense signal and a slopecompensation ramp. At the beginning of each clock cycle, the internal power switch turns on until the PWM comparator trips. During this time the current in the inductor ramps up, storing energy in the inductor's magnetic field. When the power switch turns off, the inductor releases the stored energy while the current ramps down, providing current to the output. Fault Protection The MAX8614A/MAX8614B have robust fault and overload protection. After power-up, the device is set to detect an out-of-regulation state that could be caused by an overload or short condition at either output. If either output remains in overload for more than 100ms, both converters turn off and the FLT flag asserts low. During a short-circuit condition longer than 100ms on the positive output, foldback current limit protects the output. During a short-circuit condition longer than 100ms on the negative output, both converters turn off and the FLT flag asserts low. The converters then remain off until the device is reinitialized by resetting the controller. The MAX8614A/MAX8614B also have thermal shutdown. When the device temperature reaches +170C (typ), the device shuts down. When it cools down by 20C (typ), the converters turn on. Enable (ONBST/ONINV) Applying a high logic-level signal to ONBST/ONINV turns on the converters using the soft-start and poweron sequencing described below. Pulling ONBST/ ONINV low puts the IC in shutdown mode, turning off the internal circuitry. When ONBST/ONINV goes high (or if power is applied with ONBST/ONINV high), the power-on sequence is set by SEQ. In shutdown, the device consumes only 0.1A and both output loads are disconnected from the input supply. Soft-Start and Inrush Current The step-up converter and inverter in the MAX8614A/ MAX8614B feature soft-start to limit inrush current and minimize battery loading at startup. This is accomplished by ramping the reference voltage at the input of each error amplifier. The step-up reference is ramped 10 from 0 to 1V (where 1V is the desired feedback voltage for the step-up converter), while the inverter reference is ramped down from 1.25V to 0 (where 0 is the desired feedback voltage for the inverter). During startup, the step-up converter True-Shutdown load switch turns on before the step-up-converter reference voltage is ramped up. This effectively limits inrush current peaks to below 500mA during startup. Undervoltage Lockout (UVLO) The MAX8614A/MAX8614B feature undervoltagelockout (UVLO) circuitry, which prevents circuit operation and MOSFET switching when AVCC is less than the UVLO threshold (2.55V, typ). The UVLO comparator has 25mV of hysteresis to eliminate chatter due to the source supply output impedance. Power-On Sequencing (SEQ) The MAX8614A/MAX8614B have pin-selectable internally programmed power-on sequencing. This sequencing covers all typical sequencing options required by CCD imagers. When SEQ = 0, power-on sequence can be independently controlled by ONINV and ONBST. When SEQ = 0 and ONINV and ONBST are pulled high, both outputs reach regulation simultaneously. The inverter is held off while the step-up True-Shutdown switch slowly turns on to pull PVP to VCC. The positive output rises to a diode drop below VCC. Once the step-up output reaches this voltage, the step-up and the inverter then ramp their respective references over a period of 7ms. This brings the two outputs into regulation at approximately the same time. When SEQ = 1 and ONBST and ONINV are pulled high, the step-up output powers on first. The inverter is held off until the step-up completes its entire soft-start cycle and the positive output is in regulation. Then the inverter starts its soft-start cycle and achieves regulation in approximately 7ms. True Shutdown The MAX8614A/MAX8614B completely disconnect the loads from the input when in shutdown mode. In most step-up converters, the external rectifying diode and inductor form a DC current path from the battery to the output. This can drain the battery even in shutdown if a load is connected at the step-up converter output. The MAX8614A/MAX8614B have an internal switch between the input VCC and the inductor node, PVP. When this switch turns off in shutdown there is no DC path from the input to the output of the step-up converter. This load disconnect is referred to as "True Shutdown." At Maxim Integrated MAX8614A/MAX8614B Dual-Output (+ and -) DC-DC Converters for CCD the inverter output, load disconnect is implemented by turning off the inverter's internal power switch. Current-Limit Select The MAX8614B allows an inductor current limit of 0.8A on the step-up converter and 0.75A on the inverter. The MAX8614A allows an inductor current limit of 0.44A on the step-up converter and 0.33A on the inverter. This allows flexibility in designing for higher load-current applications or for smaller, more compact designs when less power is needed. Note that the currents listed above are peak inductor currents and not output currents. The MAX8614B output current is 50mA at +15V and 100mA at -7.5V. The MAX8614A output current is 25mA at +15V and 50mA at -7.5V. Load Transient/Voltage Positioning The MAX8614A/MAX8614B match the load regulation to the voltage droop seen during load transients. This is sometimes called voltage positioning. This results in minimal overshoot when a load is removed and minimal voltage drop during a transition from light load to full load. The use of voltage positioning allows superior loadtransient response by minimizing the amplitude of overshoot and undershoot in response to load transients. DC-DC converters with high control-loop gains maintain tight DC load regulation, but still allow large voltage drops of 5% or greater for several hundred microseconds during transients. Load-transient variations are seen only with an oscilloscope (see the Typical Operating Characteristics). Since DC load regulation is read with a voltmeter, it does not show how the power supply reacts to load transients. Applications Information Adjustable Output Voltage The positive output voltage is set by connecting FBP to a resistive voltage-divider between the output and GND (Figure 1). Select feedback resistor R2 in the 30k to 100k range. R1 is then given by: V R1 = R2 BST - 1 VFBP where VFBP = 1.01V. The negative output voltage is set by connecting FBN to a resistive voltage-divider between the output and REF (Figure 1). Select feedback resistor R4 in the 30k to 100k range. R3 is then given by: V - VIMV R 3 = R4 x FBN VREF - VFBN where VREF = 1.25V and VFBN = 0V. Inductor Selection The MAX8614A/MAX8614B high switching frequency allows for the use of a small inductor. The 4.7H and 2.2H inductors shown in the Typical Operating Circuit is recommended for most applications. Larger inductances reduce the peak inductor current, but may result in skipping pulses at light loads. Smaller inductances require less board space, but may cause greater peak current due to current-sense comparator propagation delay. Use inductors with a ferrite core or equivalent. Powder iron cores are not recommended for use with high switching frequencies. The inductor's incremental saturation rating must exceed the selected current limit. For highest efficiency, use inductors with a low DC resistance (under 200m); however, for smallest circuit size, higher resistance is acceptable. See Table 1 for a representative list of inductors and Table 2 for component suppliers. Diode Selection The MAX8614A/MAX8614B high switching frequency demands a high-speed rectifier. Schottky diodes, such as the CMHSH5-2L or MBR0530L, are recommended. Make sure that the diode's peak-current rating exceeds the selected current limit, and that its breakdown voltage exceeds the output voltage. Schottky diodes are preferred due to their low forward voltage. However, ultra-high-speed silicon rectifiers are also acceptable. Table 2 lists component suppliers. Capacitor Selection Output Filter Capacitor The primary criterion for selecting the output filter capacitor is low effective series resistance (ESR). The product of the peak inductor current and the output filter capacitor's ESR determines the amplitude of the high-frequency ripple seen on the output voltage. These requirements can be balanced by appropriate selection of the current limit. For stability, the positive output filter capacitor (C1) should satisfy the following: C1 > (6L IBSTMAX ) / ( RCS D+ VBST2 ) where RCS = 0.015 (MAX8614B), and 0.035 (MAX8614A), and D+ is 1 minus the step-up switch duty cycle and is: D+ = VCC/VBST Maxim Integrated 11 MAX8614A/MAX8614B Dual-Output (+ and -) DC-DC Converters for CCD Table 1. Inductor Selection Guide OUTPUT VOLTAGES AND LOAD CURRENT 15V, 50mA -7.5V, 100mA 15V, 20mA -7.5V, 40mA INDUCTOR L (H) DCR (m) ISAT (A) SIZE (mm) TOKO DB3018C, 1069AS-2R0 2.0 72 1.4 3 x 3 x 1.8 TOKO DB3018C, 1069AS-4R3 4.3 126 0.97 3 x 3 x 1.8 TOKO S1024AS-4R3M 4.3 47 1.2 4 x 4 x 1.7 Sumida CDRH2D14-4R7 4.7 170 1 3.2 x 3.2 x 1.55 TOKO S1024AS-100M 10 100 0.8 4 x 4 x 1.7 Sumida CDRH2D11-100 10 400 0.35 3.2 x 3.2 x 1.2 Sumida CDRH2D14-100 10 295 0.46 3.2 x 3.2 x 1.55 Murata LQH32CN100K33 10 300 0.45 3.2 x 2.5 x 2 D- = VCC/VINV Table 2. Component Suppliers SUPPLIER PHONE WEBSITE INDUCTORS Murata 770-436-1300 www.murata.com Sumida 847-545-600 TOKO 847-297-0070 www.tokoam.com www.sumida.com DIODES Central Semiconductor (CMHSH5-2L) 631-435-1110 www.centralsemi.com Motorola (MBR0540L) 602-303-5454 www.motorola.com CAPACITORS Taiyo Yuden 408-573-4150 www.t-yuden.com TDK 888-835-6646 www.TDK.com For stability, the inverter output filter capacitor (C2) should satisfy the following: C2 > (6L VREF IINVMAX )/ (RCS D- (VREF - VINV) VINV) where R CS = 0.0175 (MAX8614B), and 0.040 (MAX8614A), and D- is 1 minus the inverter switch duty cycle and is: 12 Table 2 lists representative low-ESR capacitor suppliers. Input Bypass Capacitor Although the output current of many MAX8614A/ MAX8614B applications may be relatively small, the input must be designed to withstand current transients equal to the inductor current limit. The input bypass capacitor reduces the peak currents drawn from the voltage source, and reduces noise caused by the MAX8614A/MAX8614B switching action. The input source impedance determines the size of the capacitor required at the input. As with the output filter capacitor, a low-ESR capacitor is recommended. A 22F, low-ESR capacitor is adequate for most applications, although smaller bypass capacitors may also be acceptable with low-impedance sources, or if the source supply is already well filtered. Bypass AVCC separately from VCC with a 1.0F ceramic capacitor placed as close as possible to the AVCC and GND pins. PCB Layout and Routing Proper PCB layout is essential due to high-current levels and fast-switching waveforms that radiate noise. Breadboards or protoboards should never be used when prototyping switching regulators. Maxim Integrated MAX8614A/MAX8614B Dual-Output (+ and -) DC-DC Converters for CCD VBATT (2.7V ~ 5V) C4 22F VINV 13 VCC 1 ONBST 9 ONINV 2 FBN R3 187k 1% R4 30.9k 1% REF 3 VBATT C5 1.0F 4 C6 0.22F LXN L2 4.7H AVCC PVP REF 12 C3 1F L1 2.2H LXP 6 FLT 10 R2 100k 1% 7 FBP GND 5 SEQ D1 CMHSH5-21 VBST C1 +15V AT 50mA 2.2F VBST R1 1.4M 1% VINV C2 -7.5V AT 100mA 4.7F MAX8614A MAX8614B R5 100k FAULT D2 CMHSH5-21 14 8 PGND 11 Figure 1. Typical Application Circuit It is important to connect the GND pin, the input bypass-capacitor ground lead, and the output filtercapacitor ground lead to a single point (star ground configuration) to minimize ground noise and improve regulation. Also, minimize lead lengths to reduce stray capacitance, trace resistance, and radiated noise, with Maxim Integrated preference given to the feedback circuit, the ground circuit, and LX_. Place feedback resistors R1-R4 as close as possible to their respective feedback pins. Place the input bypass capacitor as close as possible to AVCC and GND. 13 MAX8614A/MAX8614B Dual-Output (+ and -) DC-DC Converters for CCD Package Information Chip Information PROCESS: BiCMOS 14 For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 14 TDFN T1433+2 21-0137 90-0063 Maxim Integrated MAX8614A/MAX8614B Dual-Output (+ and -) DC-DC Converters for CCD Revision History REVISION NUMBER REVISION DATE 2 6/14 DESCRIPTION Added MAX8614ETD/V+ to Ordering Information PAGES CHANGED 1 Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 ________________________________ 15 (c) 2014 Maxim Integrated Products, Inc. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: MAX8614BETD+TCK5 MAX8614AETD+T MAX8614BETD+T