1
711 Series Single/Multi Way
Bayonet Coupled Connectors
Data Bus Interconnection System
DB2
This high density Data Bus Interconnection System has
been designed specifically for use with data transmission
as defined MIL-STD-15538, STANAG 3838 and DEF
STAN 00-18 (Part 2).
Approved to BS 9522 F0042 and qualified to PAN
6484/6499 this interconnection system is also ideal
for use with video transmission systems and the
termination of screened twisted pairs.
Amphenol
2
Single/Multi Way Bayonet Couplin
g Connectors
(All crimp contact. All contacts grounded to shell)
Single Way Plug (to accept EL 2112 Patt.
602 back end accessories) - 06E08-1 S
Single Way Plug 06E 08
-
1 S (510)
Multi Way Plug
-
06E /C2811
-
/PAN 6486 F
Single Way Plug with heavy duty Coupling Ring -
05E08-1 S (To accept EL 2112 Patt. 602 back end
accessories) Single way plug with heavy duty coupling ring
05E08-1 S(510)
Multi Way Plug with heavy duty Coupling Ring
-
05E /C2812
Shell C2 G H L
Size Max.
Dia. max. max. Thd
UNEF 2A
31.18 7.50 31.24
14 (1.267) (0.295) (1.230) 7/8 - 20
36.93 7.50 31.24
16 (1.454) (0.295) (1.230) 1 – 20
39.70 7.50 31.24
18 (1.563) (0.295) (1.230) 1 1/16 -18
42.85 7.50 31.24
20 (1.687) (0.295) (1.230) 1 3/16 -18
45.64 7.50 31.24
22 (1.797) (0.295) (1.230) 1 5/16 - 18
48.82 7.50 31.24
24 (1.922) (0.295) (1.230) 1 7/16 – 18
Shell C G H L
Size max.
Dia. max. max. Thd
UNEF 2A
30.05 7.50 31.24
14 (1.183) (0.295) (1.230) 7/8 - 20
33.15 7.50 31.24
16 (1.305) (0.295) (1.230) 1 - 20
35.33 7.50 31.24
18 (1.391) (0.295) (1.230) 1 1/16 -18
38.89 7.50 31.24
20 (1.531) (0.295) (1.230) 1 3/16 -18
42.06 7.50 31.24
22 (1.656) (0.295) (1.230) 1 5/16 - 18
45.14 7.50 31.24
24 (1.777) (0.295) (1.230) 1 7/16 – 18
3
Sin
gle Way Single Hole Mtg. Receptacle
-
07E08
-
1 P
Multi Way Single Hole Mtg. Receptacle
-
07E /C2814
-
/PAN 6486A
P Panel
thickness
Shell
Size B
Max. D
SQ E
max. F
max. G
max. KA/F
max. L Thd
UNEF 2A
M
max.
dia. max. min.
V
min.
W dia
± 0.13
(± .005)
Z1
± 0.13
(± .005)
Z
± 0.13
(± .005)
17.96 35.33 2.87 30.86 7.50 30.61 22.25 4.75 1.57 36.32 25.65 23.80 24.08
14
(0.707)
(1.391)
(0.113)
(1.215)
(0.295)
(1.205)
7/8 – 20
(0.876)
(0.187)
(0.062)
(1.430)
(1.010)
(0.937)
(0.948)
17.96 38.51 2.87 30.86 7.50 33.76 25.43 4.75 1.57 39.88 28.83 26.95 27.23
16
(0.707)
(1.516)
(0.113)
(1.215)
(0.295)
(1.329)
1 – 20
(1.001)
(0.187)
(0.062)
(1.570)
(1.135)
(1.061)
(1.072)
17.96 41.68 2.87 30.86 7.50 36.96 28.60 4.75 1.57 43.69 32.00 30.12 30.40
18
(0.707)
(1.641)
(0.113)
(1.215)
(0.295)
(1.455)
1 1/16 – 18
(1.126)
(0.187)
(0.062)
(1.720)
(1 260)
(1.186)
(1.197)
19.61 46.43 3.76 32.38 7.50 40.11 31.78 6.35 1.57 47.37 35.18 33.30 33.58
20
(0.772)
(1.828)
(0.148)
(1.275)
(0.295)
(1.579)
1 3/16 – 18
(1 251)
(0.250)
(0.062)
(1.865)
(1.385)
(1.311)
(1.322)
19.61 49.63 3.76 32.38 7.50 43.31 34.95 6.35 1.57 50.93 38.35 36.47 36.75
22
(0.772)
(1.954)
(0.148)
(1.275)
(0.295)
(1.705)
1 5/16 – 18
(1 376)
(0.250)
(0.062)
(2.005)
(1.510)
(
1.436)
(1.447)
19.61 52.78 3.76 32.38 7.50 46.46 38.13 5.56 1.57 54.61 41.53 39.65 39.93
24
(0.772)
(2.078)
(0.148)
(1.275)
(0.295)
(1.829)
1 7/16 – 18
(1.501)
(0.219)
(0.062)
(2.150)
(1.635)
(1 561)
(1.572)
Single Way Flange Mtg. Receptacle
-
OOE08
-
1
P
4
Multi Way Flange Mtg. Receptacle
-
OOE /C2813
-
/PAN 6486B
-
B C d1 dia d2 dia E F G L Thd M1 M2 P1 P2 V W dia x sq
± 0.38 sq. ± 0.05 ± 0.13 ± 0.41 UNEF 2A Dia. Dia. max. max. min. ± 0.13 ± 0.13
Shell
Size (± .015) max. (± .002) (± .005) (± .016) max. max. max. max. (± .005) (± .005)
11.33 28.98 3.18 3.25 1.57 30.86 7.50 22.25 22.22 3.18 2.21 33.15 25.12 23.01
14 (0 446) (1.141) (0.125) (0.128) (0.062) (1.215) (0295) 7/8 – 20 (0.876) (0.875) (0 125) (0.087) (1.305) (0.989) (0.906)
11.33 31.34 3.18 3.25 1.57 30.86 7.50 25.43 25.40 3.18 2.21 37.85 28.27 24.61
16 (0.446) (1.234) (0.125) (0.128) (0.062) (1.215) (0.295) 1 – 20 (1.001) (1.000) (0.125) (0.087) (1.490) (1.113) (0.969)
11.33 33.73 3.18 3.25 1.57 30.86 7.50 28.60 26.97 3.18 2.21 40.64 31.45 26.97
18 (0.446) (1.328) (0.125) (0.128) (0.062) (1.215) (0.295) 1 1/16 – 18 (1.126) (1.062) (0.125) (0.087) (1.600) (1.238) (1.062)
14.50 36.91 3.18 3.25 2.39 32.38 7.50 31.78 30.15 3.18 5.38 43.81 34.62 29.36
20 (0.571) (1.453) (0.125) (0.128) (0.094) (1.275) (0.295) 1 3/16 – 18 (1.251) (1.187) (0.125) (0.212) (1.725) (1.363) (1.156)
14.50 40.08 3.18 3.25 2.39 32.38 7.50 34.95 33.32 3.18 5.38 46.61 37.80 31.75
22 (0.571) (1.578) (0.125) (0.128) (0.094) (1.275) (0.295) 1 5/16 – 18 (1.376) (1.312) (0.125) (0.212) (1.835) (1.488) (1.250)
15.37 43.26 3.86 3.94 2.39 32.38 7.50 38.13 36.50 3.18 5.38 49.78 41.02 34.92
24 (0.605) (1.703) (0.152) (0.155) (0.094) (1.275) (0295) 1 7/16 – 18 (1.501) (1.437) (0.125) (0.212) (1.960) (1.615) (1.375)
Multi Way Flange Mtg. Receptacle with P.C. Termination Contacts
-
02A (219) Deviation /C2815
-
Shell
Size B
max.
C
Sq.
max.
D Dia.
±0.05
(±0.002)
E
max. G
max.
M
Dia.
max.
P
max.
11.71 28.98 3.18 1.96 9.37 22.25 2.21
14 (0.461)
(1.141)
(0.125)
(0.077)
(0.369)
(0.876)
(0.087)
11.71 31.34 3.18 1.96 9.37 25.43 2.21
16 (0.461)
(1.234)
(0.125)
(0.077)
(0.369)
(1.001)
(0.087)
11.71 33.73 3.18 1.96 9.37 28.60 2.21
18 (0.461)
(1.328)
(0.125)
(0.077)
(0.369)
(1.126)
(0.087)
PANEL PIERCING
AS FOR –00E
5
Single Way Plug Terminator 77± 1%-06ET08-1S (77)
Multi Way Insert Availability
Lettering of inserts shown here corresponds to views of front (mating) surface of pin inserts.
Protective Caps and Backshells
This series of connectors is designed to use
EL2112 Patt. 602 accessories.
6
Terminatin
g
Contacts (for use with multi way connectors)
Pin terminator 3KΩ±5% - 711-0176-3K also 77Ω±1%
Socket terminator 3KΩ±5% - 711-0125-3K also 77Ω±1%
Dummy Contact and Seal Plu
g
Kit (for use with multi way connectors)
Pin 711-0174-P
Socket 711-0174-S
Contacts
Pin 711-0013-2 Socket 711-0014-3
Tools for 711 Series Connectors
Centre contact crimp-Crimp tool M22520/2-01.
Positioner 2946 B-5027-1.
Intermediate/Outer crimp - Crimp tool 227-944 (M22520/5-01).
Die Set 294GB-5026-1.
Insertion/Removal tool -294GB-5028.
Metal removal tool - 294GB-5047.
Sin
g
le/Multi Wa
y
Ordering by Amphenol Part Numbers
Insert Arran
g
ement
711 - 06 E 22-10 S B (XXX)
Series desi
g
nation:
711
Shell style:
00 - Receptacle, square flange
02 - Receptacle with P.C. termination
contacts
05 - Plug with heavy duty coupling ring
06 - Plug
07 - Receptacle, sealed, single hole
mounting
17 - Receptacle, jam nut mounting
Environmental Code:
E - Insert, grommet seal with
threaded shell for cable
accessories
A - Square flange mount receptacle
with P.C. termination contacts
Deviations:
(219) P.C. termination contact
-02A only
(301) Connector-less contacts,
seal plugs and insertion
removal tool
(416) Electroless Nic kel finish
(484) Clinch nuts and P.C. tails
-02A only
(571) Clinch nuts (only on 00E)
Orientation (omit if normal
orientation): Keys/Keyways: B,
C, E, F
Contact style:
P - Pins
(in shell styles 00, 02 & 07)
S - Sockets
(in shell styles 05 & 06)
Number of contacts:
1, 3, 4, 6, 8, 10, 12
Shell size (in sixteenths of an
inch): 08, 14, 16, 18, 20, 22, 24
Connectors complete with contacts, seal plugs and tools, but less accessori es, are ordered using part
number with no deviation added.
7
Ordering by BS Part Number
BS 9522
F0042 C2811 14 03 F N 0
Basic Number
Shell Style
C2811 as per shell style 06E-
C2812 as per shell style 05E-
C2813 as per shell style 00E-
C2814 as per shell style 07E-
C2815 as per shell style
02A
-
Variant
0 = CAD/Olive drab
1 = Electroless nickel
2 = Zinc Cobalt/Olive drab
Key polarisation
N = Normal
B,C,E,F available
Contact Type F =
Socket contact M = Pin
contact (All plugs have
socket contacts) All
recepts have Pin
contacts)
Contact arrangement
Shell size
Ordering by Pan Part Number
PAN 6486 F 14 03 S N X
Basic number
Shell Style
Pan 6486A as per shell style 07E
Pan 6486B 00E
Pan 6486E 06E
Deviation
None = Inclusive of contacts,
seal plugs and tools
1 = Less contacts/Seal
plugs and removal tools
2 = Less contacts
Orientation
N = Normal
B,C,E,F available
Contact Type
S = Socket
P = Pin
Contact arrangements
Shell size
8
Key/Keyway Orientations
Datum is always taken from major key or keyway. In
receptacles the major keyway always remains fixed in
relation to the mounting flange. For the B,C,E and F
orientations, the three bayonet locations and associated
minor keyways are rotated complete, in accordance with
the table below.
N.B. - The accompanying diagram shows a
receptacle shell, with keyways. Corresponding key
orientations for a mating plug shell are therefore
always clockwise.
Shell
VALUES FOR α (degrees) VALUES FOR θ (degrees) VALUES FOR β (degrees)
Size
N B C E F N B C E F N B C E F
14 105 91 119 75 120 35 35 35 30 50 75 75 75 100 75
16 105 93 117 75 120 35 35 35 30 50 75 75 75 100 75
18 105 95 115 75 120 35 35 35 30 50 75 75 75 100 75
20 105 95 115 75 120 35 35 35 30 50 75 75 75 100 75
22 105 97 113 75 120 35 35 35 30 50 75 75 75 100 75
24 105 97 113 75 120 35 35 35 30 50 75 75 75 100 75
VALUES FOR ϕ (degrees) VALUES FOR ω (degrees)
Shell
ORIENTATION ORIENTATION
Size
N B C E F N B C E F
14 50 50 50 30 35 60 46 74 30 75
16 50 50 50 30 35 60 48 72 30 75
18 50 50 50 30 35 60 50 70 30 75
20 50 50 50 30 35 60 50 70 30 75
22 50 50 50 30 35 60 52 68 30 75
24 50 50 50 30 35 60 52 68 30 75
9
Size #10 Data Bus Contact Assembly Instructions
Slide clamp nut, seal and ferrule over cable.
(Nut & seal only applicable on single way
connector).
Remove outer sheath of cable to 7.5mm comb out all
braids evenly and fold back. Remove cable fillers from
stripped length. Strip the centre contact conductor to
4.5mm. Note: It is recommended that both
intermediate and centre contact conductors are
scored at the correct stripping length. The
intermediate conductor insulation should not be
removed until the centre contact has been crimped.
Crimp centre contact (Pin or Socket) on to the
stripped wire using tool M22520/2-01 and crimp
positioner 294GB-5027-1 (setting No. 4 for 24AWG)
butting rear end of contact to wire insulation. The
conductor end should be visible in the inspection
hole. Note: A second hole is permissible in the
socket contact for manufacturing purposes. It is not
required to be on the same centre line as the
inspection hole.
Strip intermediate contact conductor to 4.5mm.
Insert centre contact into centre hole of intermediate
contact conductor into the outer hole of the
intermediate contact assembly. Push firmly home
until the centre contact is felt to snap into place and
ensure that the insulation of each conductor is fully
inserted into the intermediate contact insulator. The
intermediate conductor should be visible in the
inspection hole in the intermediate contact. There
should be no loose cable strands visible. Crimp the
intermediate contact assembly using the appropriate
cavity of crimp jaw 294GB-5026-1 fitted into
M22520/5-01 tool.
10
Slide the ferrule forward under the braid to
trap the braid against the rear of the
intermediate contact insulator, for all
succeeding operations keep the ferrule firmly
against the rear of the insulator using
insertion tool (294GB-5028).
Comb the braid back evenly and flatten it
onto the ferrule.
Slide the outer contact body over
the
intermediate contact assembly and ferrule
until approximately 1.5 mm of the ferrule is
visible. Trim off the excess braid using the
rear of the outer contact body as a guide.
Ensure that there are no loose braid clippings
at the rear of the ferrule.
Pl
ace the outer contact body into the
hexagonal cavity of the crimp jaws
(294GB-5026-1). Slide the intermediate
contact assembly and ferrule fully into the
outer body using the insertion tool. The rear
of the ferrule should be -0.5 or ± 0.5 mm to
the rear of the outer contact body when fully
inserted. Complete the hexagonal crimp.
11
12
International Locations
FAR EAST
JAPAN
Nippon Interconnect Company
Head Office
2-3-27 Kudan Minami
Chiyoda-Ku Tokyo 102
Japan
Tel: (81-3) 263-5611
Telex: (781) 2324654 HQ NIC
Fax: (81-3) 239-5132
HONG KONG
Amphenol East Asia Limited
513-514 World Commerce Centre
Harbour City
11 Canton Road
TST, Kowloon
Hong Kong
Tel.: (3) 681283/4
Telex: 39289
Amphetronix Limited
Plot No. 105
Bhosari Industrial Area
Post Box No. 1
Poona 411026
India
Tel: 83363, 83463
Telex: 146237
NORTH AMERICA
CANADA
Amphenol Canada Corp.
20 Melford Drive
Scarborough, Ontario MIB 2X6
Canada
Tel.: (416) 291-4401
Telex: 065-25210
Fax: (416) 292-0647
USA AND OTHER
INTERNATIONAL AREAS
Amphenol
World Headquarters
L.P.L Investment Group Inc.
P.O. Box 384
358 Hall Avenue
Wallingford
Connecticut
C.T. 06492
Tel: 203-265-8600
Fax: 203-265-8628
Bendix Connector Operations
40-60 Delaware Street
Sidney, New York 13838-1395
Tel.: (607) 563-5011
Fax: (607) 563-5157/5118
International Catalogue System
The International Catalogue for Amphenol products
consists of an individual data catalogue for each
product series produced world-wide. Product series are
combined by product groups, and published in eight
(8) separate condensed catalogues as listed below:
Catalogue Number
Circular Environmental Connectors CE-SF
Circular Industrial Connectors CI-SF
Coaxial Connectors CC-SF
Flat Ribbon Connectors FR-SF
Printed Circuit Connectors PC-SF
Rack and Panel (Rectangular)
Connectors RP-SF
Fibre Optics -
Data catalogues contain a description of the
product series, technical information, specification
data, dimensions and part numbers. A data
catalogue or a condensed catalogue can be
obtained from any international location listed
above. When ordering state the catalogue. Seven Condensed Catalogues illustrate the
products by series designation.
Amphenol products produced worldwide are
shown in four product catalogue binders.
NOTICE
Products are sold subject to Amphenol s conditions of sale ("the standard conditions") All specifications and statements contained herein are believed to be correct at the time of printing, but no representation or warranty,
express or implied, is given as to any specification or statement contained herein Product specifications including performance characteristics are typical only and subject to deviation Specifications are also subject to change
without notice. User should not assume that all safety measures are indicated or that other measures may not be required No representation or warranty, express or implied, is given that any use of products (including any
stated or suggested use) does not infringe any patent, registered design or other third party rights and no stated or suggested use of products can be taken to recommend any such infringement
Amphenol Gesellschaft mbH
Tautenhayngasse 22
A-1150 Wien (Vienna)
Austria
Tel: (0222) 95 15 11
Telex: 132661 amphw a
Fax: (0222) 92 61 01
Amphenol Benelux B.V.
P.O. Box 63
3990 DB Houten
The Netherlands
Phone: (31) 3403-76499
Fax: (31) 3403-77899
Telex: (844) 40794 AMPHL NL
Amphenol Scandinavia AB
Box 742
S-19427
Upplands
Vasby
Sweden
Tel: (0760) 880 35
Telex: 1 78 90 ampheus s
Fax: (0760) 338 00
Amphenol-Tuchel
Electronics GmbH
August-HaeuBer-Str. 10
7100 Heilbronn
W. Germany
Tel: (07131) 486-0
Telex: 728 223
Fax: (49-7131) 486323
EUROPE
Amphenol Limited
Thanet Way, Whitstable,
Kent CT5 3JF,
England.
Tel.: (0227) 264411
Telex: 96157
Fax: (0227)276571
Amphenol Italia S.P.A.
Galleria Gandhi 2/27
20017 Mazzo DI RHO
Milano
Tel: 392-935 03190
Fax: 392-935 03206
Amphenol Socapex France
21 Chemin du Defois
BP 349
39105 Dole Cedex
France
Tel: (3384) 829400
Telex: (842) 360264 F UMD B
Fax: (3384) 829411
Amphenol Espana
Galileo
303-305
4a Planta 080 28
Barcelona
Spain
Tel: (34/3) 321.00.00
Fax: (34/3) 439.89.27
Telex: 98253
Amphenol
