MC14001B Series B-Suffix Series CMOS Gates MC14001B, MC14011B, MC14023B, MC14025B, MC14071B, MC14073B, MC14081B, MC14082B The B Series logic gates are constructed with P and N channel enhancement mode devices in a single monolithic structure (Complementary MOS). Their primary use is where low power dissipation and/or high noise immunity is desired. http://onsemi.com MARKING DIAGRAMS Features 14 * Supply Voltage Range = 3.0 Vdc to 18 Vdc * All Outputs Buffered * Capable of Driving Two Low-power TTL Loads or One Low-power * * * PDIP-14 P SUFFIX CASE 646 1 Schottky TTL Load Over the Rated Temperature Range. Double Diode Protection on All Inputs Except: Triple Diode Protection on MC14011B and MC14081B Pin-for-Pin Replacements for Corresponding CD4000 Series B Suffix Devices These Devices are Pb-Free and are RoHS Compliant 14 SOIC-14 D SUFFIX CASE 751A Parameter VDD Vin, Vout Iin, Iout DC Supply Voltage Range Input or Output Voltage Range (DC or Transient) Input or Output Current (DC or Transient) per Pin 140xxBG AWLYWW 1 14 14 0xxB ALYWG G TSSOP-14 DT SUFFIX CASE 948G MAXIMUM RATINGS (Voltages Referenced to VSS) Symbol MC140xxBCP AWLYYWWG Value Unit -0.5 to +18.0 V -0.5 to VDD + 0.5 V 10 mA 1 14 SOEIAJ-14 F SUFFIX CASE 965 MC140xxB ALYWG 1 TA Ambient Temperature Range -55 to +125 C Tstg Storage Temperature Range -65 to +150 C TL Lead Temperature (8-Second Soldering) 260 C xx = Specific Device Code A = Assembly Location WL, L = Wafer Lot YY, Y = Year WW, W = Work Week G or G = Pb-Free Package (Note: Microdot may be in either location) V DEVICE INFORMATION PD Power Dissipation, per Package (Note 1) VESD ESD Withstand Voltage Human Body Model Machine Model Charged Device Model 500 mW > 3000 > 300 N/A Device Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Temperature Derating: Plastic "P and D/DW" Packages: - 7.0 mW/_C From 65_C To 125_C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range VSS v (Vin or Vout) v VDD. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either VSS or VDD). Unused outputs must be left open. (c) Semiconductor Components Industries, LLC, 2011 June, 2011 - Rev. 8 1 Description MC14001B Quad 2-Input NOR Gate MC14011B Quad 2-Input NAND Gate MC14023B Triple 3-Input NAND Gate MC14025B Triple 3-Input NOR Gate MC14071B Quad 2-Input OR Gate MC14073B Triple 3-Input AND Gate MC14081B Quad 2-Input AND Gate MC14082B Dual 4-Input AND Gate ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 8 of this data sheet. Publication Order Number: MC14001B/D MC14001B Series LOGIC DIAGRAMS NAND OR AND MC14001B Quad 2-Input NOR Gate MC14011B Quad 2-Input NAND Gate MC14071B Quad 2-Input OR Gate MC14081B Quad 2-Input AND Gate 2 INPUT NOR 1 2 3 1 2 3 1 2 3 1 2 3 5 6 4 5 6 4 5 6 4 5 6 4 8 9 10 8 9 10 8 9 10 8 9 10 12 13 11 12 13 11 12 13 11 12 13 11 3 INPUT MC14025B Triple 3-Input NOR Gate 1 2 8 3 4 5 11 12 13 9 6 10 MC14073B Triple 3-Input AND Gate MC14023B Triple 3-Input NAND Gate 1 2 8 3 4 5 11 12 13 1 2 8 3 4 5 11 12 13 9 6 10 9 6 10 MC14082B Dual 4-Input AND Gate 2 3 4 5 9 10 11 12 1 13 NC = 6, 8 VDD = PIN 14 VSS = PIN 7 FOR ALL DEVICES PIN ASSIGNMENTS MC14001B Quad 2-Input NOR Gate MC14023B Triple 3-Input NAND Gate MC14011B Quad 2-Input NAND Gate MC14025B Triple 3-Input NOR Gate IN 1A 1 14 VDD IN 1A 1 14 VDD IN 1A 1 14 VDD IN 1A 1 14 VDD IN 2A 2 13 IN 2D IN 2A 2 13 IN 2D IN 2A 2 13 IN 3C IN 2A 2 13 IN 3C OUTA 3 12 IN 1D OUTA 3 12 IN 1D IN 1B 3 12 IN 2C IN 1B 3 12 IN 2C OUTB 4 11 OUTD OUTB 4 11 OUTD IN 2B 4 11 IN 1C IN 2B 4 11 IN 1C IN 1B 5 10 OUTC IN 1B 5 10 OUTC IN 3B 5 10 OUTC IN 3B 5 10 OUTC IN 2B 6 9 IN 2C IN 2B 6 9 IN 2C OUTB 6 9 OUTA OUTB 6 9 OUTA VSS 7 8 IN 1C VSS 7 8 IN 1C VSS 7 8 IN 3A VSS 7 8 IN 3A MC14071B Quad 2-Input OR Gate MC14073B Triple 3-Input AND Gate MC14081B Quad 2-Input AND Gate MC14082B Dual 4-Input AND Gate IN 1A 1 14 VDD IN 1A 1 14 VDD IN 1A 1 14 VDD OUTA 1 14 VDD IN 2A 2 13 IN 2D IN 2A 2 13 IN 3C IN 2A 2 13 IN 2D IN 1A 2 13 OUTB OUTA 3 12 IN 1D IN 1B 3 12 IN 2C OUTA 3 12 IN 1D IN 2A 3 12 IN 4B OUTB 4 11 OUTD IN 2B 4 11 IN 1C OUTB 4 11 OUTD IN 3A 4 11 IN 3B IN 1B 5 10 OUTC IN 3B 5 10 OUTC IN 1B 5 10 OUTC IN 4A 5 10 IN 2B IN 2B 6 9 IN 2C OUTB 6 9 OUTA IN 2B 6 9 IN 2C NC 6 9 IN 1B VSS 7 8 IN 1C VSS 7 8 IN 3A VSS 7 8 IN 1C VSS 7 8 NC NC = NO CONNECTION http://onsemi.com 2 MC14001B Series IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIII IIIII IIIIIIIII IIIII IIIIIII IIIIIIIIII IIIIII IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIII III III III IIII III IIII III III III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIII IIII III IIIIIIIIIIIIIIIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII ELECTRICAL CHARACTERISTICS (Voltages Referenced to VSS) Characteristic Output Voltage Vin = VDD or 0 Symbol - 55_C 25_C 125_C VDD Vdc Min Max Min Typ (2) Max Min Max Unit "0" Level VOL 5.0 10 15 - - - 0.05 0.05 0.05 - - - 0 0 0 0.05 0.05 0.05 - - - 0.05 0.05 0.05 Vdc "1" Level VOH 5.0 10 15 4.95 9.95 14.95 - - - 4.95 9.95 14.95 5.0 10 15 - - - 4.95 9.95 14.95 - - - Vdc Input Voltage "0" Level (VO = 4.5 or 0.5 Vdc) (VO = 9.0 or 1.0 Vdc) (VO = 13.5 or 1.5 Vdc) VIL 5.0 10 15 - - - 1.5 3.0 4.0 - - - 2.25 4.50 6.75 1.5 3.0 4.0 - - - 1.5 3.0 4.0 "1" Level VIH 5.0 10 15 3.5 7.0 11 - - - 3.5 7.0 11 2.75 5.50 8.25 - - - 3.5 7.0 11 - - - 5.0 5.0 10 15 - 3.0 - 0.64 - 1.6 - 4.2 - - - - - 2.4 - 0.51 - 1.3 - 3.4 - 4.2 - 0.88 - 2.25 - 8.8 - - - - - 1.7 - 0.36 - 0.9 - 2.4 - - - - IOL 5.0 10 15 0.64 1.6 4.2 - - - 0.51 1.3 3.4 0.88 2.25 8.8 - - - 0.36 0.9 2.4 - - - mAdc Input Current Iin 15 - 0.1 - 0.00001 0.1 - 1.0 mAdc Input Capacitance (Vin = 0) Cin - - - - 5.0 7.5 - - pF Quiescent Current (Per Package) IDD 5.0 10 15 - - - 0.25 0.5 1.0 - - - 0.0005 0.0010 0.0015 0.25 0.5 1.0 - - - 7.5 15 30 mAdc IT 5.0 10 15 Vin = 0 or VDD (VO = 0.5 or 4.5 Vdc) (VO = 1.0 or 9.0 Vdc) (VO = 1.5 or 13.5 Vdc) Output Drive Current (VOH = 2.5 Vdc) (VOH = 4.6 Vdc) (VOH = 9.5 Vdc) (VOH = 13.5 Vdc) Source (VOL = 0.4 Vdc) (VOL = 0.5 Vdc) (VOL = 1.5 Vdc) Total Supply Current (3) (4) (Dynamic plus Quiescent, Per Gate, CL = 50 pF) Sink IOH Vdc Vdc mAdc IT = (0.3 mA/kHz) f + IDD/N IT = (0.6 mA/kHz) f + IDD/N IT = (0.9 mA/kHz) f + IDD/N mAdc 2. Data labelled "Typ" is not to be used for design purposes but is intended as an indication of the IC's potential performance. 3. The formulas given are for the typical characteristics only at 25_C. 4. To calculate total supply current at loads other than 50 pF: IT(CL) = IT(50 pF) + (CL - 50) Vfk where: IT is in mA (per package), CL in pF, V = (VDD - VSS) in volts, f in kHz is input frequency, and k = 0.001 x the number of exercised gates per package. http://onsemi.com 3 MC14001B Series B-SERIES GATE SWITCHING TIMES IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIII IIIII IIII IIII IIII IIII III IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII SWITCHING CHARACTERISTICS (5) (CL = 50 pF, TA = 25_C) Characteristic Symbol Output Rise Time, All B-Series Gates tTLH = (1.35 ns/pF) CL + 33 ns tTLH = (0.60 ns/pF) CL + 20 ns tTLH = (0.40 ns/PF) CL + 20 ns tTLH Output Fall Time, All B-Series Gates tTHL = (1.35 ns/pF) CL + 33 ns tTHL = (0.60 ns/pF) CL + 20 ns tTHL = (0.40 ns/pF) CL + 20 ns tTHL Propagation Delay Time MC14001B, MC14011B only tPLH, tPHL = (0.90 ns/pF) CL + 80 ns tPLH, tPHL = (0.36 ns/pF) CL + 32 ns tPLH, tPHL = (0.26 ns/pF) CL + 27 ns All Other 2, 3, and 4 Input Gates tPLH, tPHL = (0.90 ns/pF) CL + 115 ns tPLH, tPHL = (0.36 ns/pF) CL + 47 ns tPLH, tPHL = (0.26 ns/pF) CL + 37 ns 8-Input Gates (MC14068B, MC14078B) tPLH, tPHL = (0.90 ns/pF) CL + 155 ns tPLH, tPHL = (0.36 ns/pF) CL + 62 ns tPLH, tPHL = (0.26 ns/pF) CL + 47 ns VDD Vdc Min Typ (6) Max 5.0 10 15 - - - 100 50 40 200 100 80 5.0 10 15 - - - 100 50 40 200 100 80 Unit ns ns tPLH, tPHL ns 5.0 10 15 - - - 125 50 40 250 100 80 5.0 10 15 - - - 160 65 50 300 130 100 5.0 10 15 - - - 200 80 60 350 150 110 5. The formulas given are for the typical characteristics only at 25_C. 6. Data labelled "Typ" is not to be used for design purposes but is intended as an indication of the IC's potential performance. 14 PULSE GENERATOR 20 ns VDD 20 ns INPUT INPUT OUTPUT 7 0V tPLH tPHL CL * VDD 90% 50% 10% OUTPUT INVERTING VSS tTHL tPLH OUTPUT NON-INVERTING *All unused inputs of AND, NAND gates must be connected to VDD. All unused inputs of OR, NOR gates must be connected to VSS. tTLH Figure 1. Switching Time Test Circuit and Waveforms http://onsemi.com 4 VOH 90% 50% 10% tTLH tPHL 90% 50% 10% tTHL VOL VOH VOL MC14001B Series CIRCUIT SCHEMATIC NOR, OR GATES MC14001B, MC14071B One of Four Gates Shown MC14025B One of Three Gates Shown VDD VDD 14 VDD 1, 3, 11 1, 6, 8, 13 * 2, 4, 12 2, 5, 9, 12 14 VDD 3, 4, 10, 11 * VSS VSS 7 9, 6, 10 VSS VDD *Inverter omitted in MC14001B 8, 5, 13 7 VSS VSS *Inverter omitted in MC14025B CIRCUIT SCHEMATIC NAND, AND GATES MC14023B, MC14073B One of Three Gates Shown MC14011B, MC14081B One of Four Gates Shown VDD 14 VDD * 3, 4, 10, 11 2, 4, 12 1, 3, 11 14 2, 5, 9, 12 VDD 1, 6, 8, 13 VSS 7 VSS *Inverter omitted in MC14011B * VDD 9, 6, 10 8, 5, 13 7 VSS VSS *Inverter omitted in MC14023B http://onsemi.com 5 MC14001B Series TYPICAL B-SERIES GATE CHARACTERISTICS N-CHANNEL DRAIN CURRENT (SINK) P-CHANNEL DRAIN CURRENT (SOURCE) - 10 5.0 ID , DRAIN CURRENT (mA) ID , DRAIN CURRENT (mA) - 9.0 4.0 TA = - 55C 3.0 - 40C + 85C + 25C 2.0 + 125C 1.0 - 8.0 TA = - 55C - 7.0 - 40C - 6.0 - 5.0 + 25C + 85C - 4.0 - 3.0 + 125C - 2.0 - 1.0 0 0 1.0 2.0 3.0 4.0 VDS, DRAIN-TO-SOURCE VOLTAGE (Vdc) 0 5.0 0 Figure 2. VGS = 5.0 Vdc - 50 - 45 TA = - 55C 16 14 - 40C 12 + 25C + 85C 10 ID , DRAIN CURRENT (mA) ID , DRAIN CURRENT (mA) 18 + 125C 8.0 6.0 - 40 - 35 - 25 + 85C - 15 2.0 - 5.0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 VDS, DRAIN-TO-SOURCE VOLTAGE (Vdc) 9.0 0 10 - 40C + 25C - 20 - 10 0 TA = - 55C - 30 4.0 + 125C 0 Figure 4. VGS = 10 Vdc - 100 45 - 90 40 - 80 35 TA = - 55C 30 - 40C 25 + 25C ID , DRAIN CURRENT (mA) ID , DRAIN CURRENT (mA) - 1.0 - 2.0 - 3.0 - 4.0 - 5.0 - 6.0 - 7.0 - 8.0 - 9.0 - 10 VDS, DRAIN-TO-SOURCE VOLTAGE (Vdc) Figure 5. VGS = - 10 Vdc 50 + 85C 20 + 125C 15 10 5.0 0 - 5.0 Figure 3. VGS = - 5.0 Vdc 20 0 - 1.0 - 2.0 - 3.0 - 4.0 VDS, DRAIN-TO-SOURCE VOLTAGE (Vdc) - 70 - 60 TA = - 55C - 50 - 40C + 25C - 40 + 85C - 30 + 125C - 20 - 10 0 2.0 4.0 6.0 8.0 10 12 14 16 VDS, DRAIN-TO-SOURCE VOLTAGE (Vdc) 18 0 20 0 Figure 6. VGS = 15 Vdc - 2.0 - 4.0 - 6.0 - 8.0 - 10 - 12 - 14 - 16 VDS, DRAIN-TO-SOURCE VOLTAGE (Vdc) Figure 7. VGS = - 15 Vdc These typical curves are not guarantees, but are design aids. Caution: The maximum rating for output current is 10 mA per pin. http://onsemi.com 6 - 18 - 20 MC14001B Series TYPICAL B-SERIES GATE CHARACTERISTICS (cont'd) V out , OUTPUT VOLTAGE (Vdc) V out , OUTPUT VOLTAGE (Vdc) VOLTAGE TRANSFER CHARACTERISTICS SINGLE INPUT NAND, AND MULTIPLE INPUT NOR, OR 5.0 4.0 SINGLE INPUT NOR, OR MULTIPLE INPUT NAND, AND 3.0 2.0 1.0 0 0 1.0 2.0 SINGLE INPUT NAND, AND MULTIPLE INPUT NOR, OR 10 8.0 SINGLE INPUT NOR, OR MULTIPLE INPUT NAND, AND 6.0 4.0 2.0 0 3.0 4.0 5.0 Vin, INPUT VOLTAGE (Vdc) 2.0 0 Figure 8. VDD = 5.0 Vdc V out , OUTPUT VOLTAGE (Vdc) 6.0 8.0 10 Vin, INPUT VOLTAGE (Vdc) Figure 9. VDD = 10 Vdc DC NOISE MARGIN 16 SINGLE INPUT NAND, AND MULTIPLE INPUT NOR, OR 14 The DC noise margin is defined as the input voltage range from an ideal "1" or "0" input level which does not produce output state change(s). The typical and guaranteed limit values of the input values VIL and VIH for the output(s) to be at a fixed voltage VO are given in the Electrical Characteristics table. VIL and VIH are presented graphically in Figure 11. Guaranteed minimum noise margins for both the "1" and "0" levels = 12 SINGLE INPUT NOR, OR MULTIPLE INPUT NAND, AND 10 8.0 6.0 4.0 2.0 0 4.0 0 2.0 4.0 1.0 V with a 5.0 V supply 2.0 V with a 10.0 V supply 2.5 V with a 15.0 V supply 6.0 8.0 10 Vin, INPUT VOLTAGE (Vdc) Figure 10. VDD = 15 Vdc Vout VDD Vout VO VO VO VO VDD VDD 0 VDD Vin VIL 0 VIH Vin VIL VIH VSS = 0 VOLTS DC (a) Inverting Function (b) Non-Inverting Function Figure 11. DC Noise Immunity http://onsemi.com 7 MC14001B Series ORDERING INFORMATION Package Shipping MC14001BCPG PDIP-14 (Pb-Free) 25 Units / Rail MC14001BDG SOIC-14 (Pb-Free) 55 Units / Rail MC14001BDR2G SOIC-14 (Pb-Free) Device 2500 Units / Tape & Reel MC14001BDTR2G TSSOP-14* (Pb-Free) MC14001BFELG SOEIAJ-14 (Pb-Free) 2000 Units / Tape & Reel MC14011BCPG PDIP-14 (Pb-Free) 25 Units / Rail MC14011BDG SOIC-14 (Pb-Free) 55 Units / Rail MC14011BDR2G SOIC-14 (Pb-Free) 2500 Units / Tape & Reel MC14011BDTR2G TSSOP-14* (Pb-Free) MC14011BFG SOEIAJ-14 (Pb-Free) 50 Units / Rail MC14011BFELG SOEIAJ-14 (Pb-Free) 2000 Units / Tape & Reel MC14023BCPG PDIP-14 (Pb-Free) 25 Units / Rail MC14023BDG SOIC-14 (Pb-Free) 55 Units / Rail MC14023BDR2G SOIC-14 (Pb-Free) 2500 Units / Tape & Reel MC14023BFELG SOEIAJ-14 (Pb-Free) 2000 Units / Tape & Reel MC14025BCPG PDIP-14 (Pb-Free) 25 Units / Rail MC14025BDG SOIC-14 (Pb-Free) 55 Units / Rail MC14025BDR2G SOIC-14 (Pb-Free) 2500 Units / Tape & Reel MC14025BFELG SOEIAJ-14 (Pb-Free) 2000 Units / Tape & Reel MC14071BCPG PDIP-14 (Pb-Free) 25 Units / Rail MC14071BDG SOIC-14 (Pb-Free) 55 Units / Rail MC14071BDR2G SOIC-14 (Pb-Free) 2500 Units / Tape & Reel MC14071BDTG TSSOP-14* (Pb-Free) 96 Units per Rail MC14071BDTR2G TSSOP-14* (Pb-Free) 2500 Units / Tape & Reel http://onsemi.com 8 MC14001B Series ORDERING INFORMATION Package Shipping MC14071BFELG SOEIAJ-14 (Pb-Free) 2000 Units / Tape & Reel MC14073BCPG PDIP-14 (Pb-Free) 25 Units / Rail MC14073BDG SOIC-14 (Pb-Free) 55 Units / Rail MC14073BDR2G SOIC-14 (Pb-Free) 2500 Units / Tape & Reel MC14073BFELG SOEIAJ-14 (Pb-Free) 2000 Units / Tape & Reel MC14081BCPG PDIP-14 (Pb-Free) 25 Units / Rail MC14081BDG SOIC-14 (Pb-Free) 55 Units / Rail MC14081BDR2G SOIC-14 (Pb-Free) Device 2500 Units / Tape & Reel MC14081BDTR2G TSSOP-14* (Pb-Free) MC14081BFELG SOEIAJ-14 (Pb-Free) 2000 Units / Tape & Reel MC14082BCPG PDIP-14 (Pb-Free) 2000 Units / Box MC14082BDG SOIC-14 (Pb-Free) 55 Units / Rail MC14082BDR2G SOIC-14 (Pb-Free) 2500 Units / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *This package is inherently Pb-Free. http://onsemi.com 9 MC14001B Series PACKAGE DIMENSIONS PDIP-14 CASE 646-06 ISSUE P 14 8 1 7 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. B A F L N C -T- SEATING PLANE H G D 14 PL J K 0.13 (0.005) M M http://onsemi.com 10 DIM A B C D F G H J K L M N INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.290 0.310 --- 10 _ 0.015 0.039 MILLIMETERS MIN MAX 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.37 7.87 --- 10 _ 0.38 1.01 MC14001B Series PACKAGE DIMENSIONS SOIC-14 NB CASE 751A-03 ISSUE K D A B 14 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF AT MAXIMUM MATERIAL CONDITION. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSIONS. 5. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. A3 E H L 1 0.25 M DETAIL A 7 B 13X M b 0.25 M C A S B S e DETAIL A h A X 45 _ M A1 C SEATING PLANE DIM A A1 A3 b D E e H h L M MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.19 0.25 0.35 0.49 8.55 8.75 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_ SOLDERING FOOTPRINT* 6.50 14X 1.18 1 1.27 PITCH 14X 0.58 DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 11 INCHES MIN MAX 0.054 0.068 0.004 0.010 0.008 0.010 0.014 0.019 0.337 0.344 0.150 0.157 0.050 BSC 0.228 0.244 0.010 0.019 0.016 0.049 0_ 7_ MC14001B Series PACKAGE DIMENSIONS TSSOP-14 CASE 948G-01 ISSUE B 14X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S S N 2X 14 L/2 0.25 (0.010) 8 M B -U- L PIN 1 IDENT. N F 7 1 0.15 (0.006) T U NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. S S DETAIL E K A -V- EEE CCC CCC EEE K1 J J1 DIM A B C D F G H J J1 K K1 L M SECTION N-N -W- C 0.10 (0.004) -T- SEATING PLANE D H G DETAIL E SOLDERING FOOTPRINT* 7.06 1 0.65 PITCH 14X 0.36 14X 1.26 DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 12 MILLIMETERS INCHES MIN MAX MIN MAX 4.90 5.10 0.193 0.200 4.30 4.50 0.169 0.177 --- 1.20 --- 0.047 0.05 0.15 0.002 0.006 0.50 0.75 0.020 0.030 0.65 BSC 0.026 BSC 0.50 0.60 0.020 0.024 0.09 0.20 0.004 0.008 0.09 0.16 0.004 0.006 0.19 0.30 0.007 0.012 0.19 0.25 0.007 0.010 6.40 BSC 0.252 BSC 0_ 8_ 0_ 8_ MC14001B Series PACKAGE DIMENSIONS SOEIAJ-14 CASE 965-01 ISSUE B 14 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). LE 8 Q1 E HE M_ L 7 1 DETAIL P Z D VIEW P A e A1 b 0.13 (0.005) c M 0.10 (0.004) DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.10 0.20 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --1.42 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.004 0.008 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --0.056 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 13 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC14001B/D