PCMCIA Flash Memory Card FLA Series PCMCIA Flash Memory Card 1 MEGABYTE through 40 MEGABYTE (Intel/Sharp based) General Description Features WEDC's FLA Series Flash memory cards offer high density linear Flash solid state storage solutions for code and data storage, high performance disk emulation and execute in place (XIP) applications in mobile PC and dedicated (embedded) equipment. * Low cost High Density Linear Flash Card FLA series cards conform to PCMCIA international standard. The card's control logic provides the system interface and controls the internal Flash memories. Card can be read/written in byte-wide or word-wide mode which allows for flexible integration into various systems. Combined with file management software, such as Flash Translation Layer (FTL), FLA Flash cards provide removable high-performance disk emulation. The FLA series offers low power modes controlled by registers. Standard cards contain separate 2kB EEPROM memory for Card Information Structure (CIS) which can be used for easy identification of card characteristics. The WEDC FLA series is based on Intel/Sharp Flash memories. * Supports 5V only systems or 5V systems with 12V VPP * Based on Intel/Sharp FlashFile Components * Fast Read Performance - 150ns or 200ns Maximum Access Time * x8 / x16 Data Interface * High Performance Random Writes - 8s Typical Word Write Time * Automated Write and Erase Algorithms - Command User Interface * 100,000 Erase Cycles per Block * 64K word symmetrical Block Architecture * PC Card Standard Type I Form Factor Note: Standard options include attribute memory. Cards without attribute memory are available. Cards are also available with or without a hardware write protect switch. Architecture Overview WEDC's FLA series is designed to support from 2 to 20, 4Mb, 8Mb or 16Mb components, providing a wide range of density options. Cards are based on the 28F008SA (8Mb) for 12V VPP applications or on the 28F004S5 (4Mb), 28F008S5 (8Mb) and 28F016S5 (16Mb) devices for 5V only applications. Devices codes for the 28F004S5, 28F008SA, 28F008S5 and the 28F016S5 are: A7H, A2H, A6H and AAh respectively. Systems should be able to recognize all four codes. Cards utilizing the 8Mb components provide densities ranging from 2MB to 20MB in 2MB increments, cards utilizing 16Mb components provide densities ranging from 4MB to 40MB in 4MB increments. 4 Mbit memory devices are used only for smallest capacity cards (1MB). In support of the PC Card 95 standard for word wide access devices are paired. Therefore, the Flash array is structured in 64K word (128kBytes) blocks. Write, read and block erase operations can be performed as either a word or byte wide operation . By multiplexing A0, CE1# and CE2#, 8-bit hosts can access all data on data lines DQ0 - DQ7. The FLA21-FLA36 series also supports the following PCMCIA compatible register functions: Soft Reset via the Configuration Option Register, Power Down (sleep mode) via the Configuration and Status Register and monitoring of Ready/Busy, Soft Reset and Power Down via the Card Status Register (cards without attribute memory and versions FLA51 - FLA66 do not have registers). The FLA series cards conform with the PC Card Standard (PCMCIA) and JEIDA, providing electrical and physical compatibility. The PC Card form factor offers an industry standard pinout and mechanical outline, allowing density upgrades without system design changes. WEDC's standard cards are shipped with WEDC's Logo. Cards are also available with blank housings (no Logo). The blank housings are available in both a recessed (for label) and flat housing. Please contact WEDC sales representative for further information on Custom artwork. August 2000 Rev. 4 - ECO #13125 1 PC Card Products PCMCIA Flash Memory Card FLA Series Manuf ID Device ID Block Diagram Device type Device Pair (N/2 - 1) CSn Device (N-2) Device (N-1) Array Address Bus 28F004S5 89H A7H 28F008SA 89H A2H 28F008S5 89H A6H 28F016S5 89H AAH ADDRESS BUFFER ADDRESS BUS A1-A25 Control Address Bus M Res WL# RL# WH# RH# Device Pair 1 Device 3 Device Pair 0 Device 2 Device 1 CS1 WE# OE# Control Logic PCMCIA Interface CE2# CE1# CSn Cn CS0 C0 Ctrl REG# A0 WP At/Reg enable /SR /PD CS0 Device 0 Card Management Registers 4000h Vcc WH# RH# DATA BUS Q0-Q7 DATA BUS Q8-Q15 SR Clr Reg Clr WL# RL# 0000h attrib. mem CIS EEPROM 2kB Vcc control Q0-Q7 Vcc I/O buffer DATA BUS D8-D15 DATA BUS D0-D7 Registers in Attribute Memory Space CSR Configuration Status Register: ADRS=4002h Register NAME ADDRESS 4100h Status Reg. 4002h 4000h Config. and Status Reg. D7 D6 D5 D4 D3 D2 D1 D0 D2 Power Down; active High 1=Place all memory devices in power down mode 0=normal operation Power On default=0 Configuration Option Register SR Read Only Status Register: ADRS=4100h COR not supported SReset Configuration Option Register: ADRS=4000h SRES LREQ D7 D6 D5 Write Only D7 -Configuration IndexD4 D3 D2 D1 D0 D6 D5 PDwn not supported R/BSY D4 D3 D2 D1 D0 D5 Represents the state of SRESET bit in COR (4000h) 1=Reset 0=Normal operation Power On default D5=0 D3 Represents the state of Power Down bit (D2) in CSR (4002h) 1=Power Down D0 Reflects the card's Ready/Busy signal (pin 16) driven by memory components Ready/Busy outputs.This bit allows software polling of the card's Ready/Busy status. 1=Ready D7 Soft Reset, active High 1 = Reset State 0 = End Reset State D6 LevelReq (not supported) D5-D0 Configuration index (not supported) August 2000 Rev. 4 - ECO #13125 Write Only PDwn not supported not supported 2 PC Card Products PCMCIA Flash Memory Card FLA Series Pinout Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Signal name GND DQ3 DQ4 DQ5 DQ6 DQ7 CE1# A10 OE# A11 A9 A8 A13 A14 WE# RDY/BSY# Vcc Vpp1 A16 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 DQ0 DQ1 DQ2 WP GND I/O I/O I/O I/O I/O I/O I I I I I I I I I O I I I I I I I I I I I I/O I/O I/O O Function Ground Data bit 3 Data bit 4 Data bit 5 Data bit 6 Data bit 7 Card enable 1 Address bit 10 Output enable Address bit 11 Address bit 9 Address bit 8 Address bit 13 Address bit 14 Write Enable Ready/Busy Supply Voltage Prog. Voltage Address bit 16 Address bit 15 Address bit 12 Address bit 7 Address bit 6 Address bit 5 Address bit 4 Address bit 3 Address bit 2 Address bit 1 Address bit 0 Data bit 0 Data bit 1 Data bit 2 Write Potect Ground Active LOW LOW LOW LOW (4) N.C. HIGH Pin 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 Signal name GND CD1# DQ11 DQ12 DQ13 DQ14 DQ15 CE2# VS1 RFU RFU A17 A18 A19 A20 A21 Vcc Vpp2 A22 A23 A24 A25 VS2 RST Wait# RFU REG# BVD2 BVD1 DQ8 DQ9 DQ10 CD2# GND I/O O I/O I/O I/O I/O I I O I I I I I I I I I O I O I O O I/O I/O O O Function Ground Card Detect 1 Data bit 11 Data bit 12 Data bit 13 Data bit 14 Data bit 15 Card Enable 2 Voltage Sense 1 Reserved Reserved Address bit 17 Address bit 18 Address bit 19 Address bit 20 Address bit 21 Supply Voltage Prog. Voltage Address bit 22 Address bit 23 Address bit 24 Address bit 25 Voltage Sense 2 Card Reset Extended Bus cycle Reserved Attrib Mem Select Bat. Volt. Detect 2 Bat. Volt. Detect 1 Data bit 8 Data bit 9 Data bit 10 Card Detect 2 Ground Active LOW LOW N.C. 2MB(3) 4MB(3) N.C. 8MB(3) 16MB(3) 32MB(3) 64MB(3) N.C. HIGH (4) Low(2,4) (2) (2) LOW Notes: 1. RDY/BSY signal is an "Open drain" type output, pull-up resistor on host side is required. 2. Wait#, BVD1 and BVD2 are driven high for compatibility. 3. Shows density for which specified address bit is MSB. Higher order address bits are no connects (ie 4MB A21 is MSB A22 - A25 are NC). 4. NC - No Connection for FLA51 - FLA66. Mechanical Interconnect area 1.0mm 0.05 (0.039") 1.6mm 0.05 (0.063") 3.0mm MIN 10.0mm MIN (0.400") Substrate area 85.6mm 0.20 (3.370") 1.0mm 0.05 (0.039") 10.0mm MIN (0.400") August 2000 Rev. 4 - ECO #13125 54.0mm 0.10 (2.126") 3.3mm T1 (0.130") T1=0.10mm interconnect area T1=0.20mm substrate area 3 PC Card Products PCMCIA Flash Memory Card FLA Series Card Signal Description Symbol Type A0 - A25 INPUT DQ0 - DQ15 INPUT/OUTPUT CE1#, CE2# INPUT OE# INPUT WE# INPUT RDY/BSY# OUTPUT CD1#, CD2# OUTPUT WP OUTPUT VPP1, VPP2 N.C. VCC GND REG# INPUT RST INPUT WAIT# OUTPUT BVD1, BVD2 OUTPUT VS1, VS2 OUTPUT Name and Function ADDRESS INPUTS: A0 through A25 enable direct addressing of up to 64MB of memory on the card. Signal A0 is not used in word access mode. A25 is the most significant bit DATA INPUT/OUTPUT: DQ0 THROUGH DQ15 constitute the bidirectional databus. DQ15 is the MSB. CARD ENABLE 1 AND 2: CE1# enables even byte accesses, CE2# enables odd byte accesses. Multiplexing A0, CE1# and CE2# allows 8bit hosts to access all data on DQ0 - DQ7. OUTPUT ENABLE: Active low signal gating read data from the memory card. WRITE ENABLE: Active low signal gating write data to the memory card. READY/BUSY OUTPUT: Indicates status of internally timed erase or program algorithms. A high output indicates that the card is ready to accept accesses. A low output indicates that one or more devices in the memory card are busy with internally timed erase or write activities. CARD DETECT 1 and 2: Provide card insertion detection. These signals are internally connected to ground on the card. The host shall monitor these signals to detect card insertion (pulled-up on host side). WRITE PROTECT: Write protect reflects the status of the Write Protect switch on the memory card. WP set to high = write protected, providing internal hardware write lockout to the Flash array. If card does not include optional write protect switch, this signal will be pulled low internally indicating write protect = "off". PROGRAM/ERASE POWER SUPPLY: Provides programming voltages for card (12V). Not connected for 5V only card. CARD POWER SUPPLY: (5.0V). CARD GROUND ATTRIBUTE MEMORY SELECT : Active low signal, enables access to Attribute Memory Plane, occupied by Card Information Structure and Card Registers. RESET: Active high signal for placing card in Power-on default state. Reset can be used as a Power-Down signal for the memory array. WAIT: This signal is pulled high internally for compatibility. No wait states are generated. BATTERY VOLTAGE DETECT: These signals are pulled high to maintain SRAM card compatibility. VOLTAGE SENSE: Notifies the host socket of the card's VCC requirements. VS1 and VS2 are open to indicate a 5V card . RESERVED FOR FUTURE USE NO INTERNAL CONNECTION TO CARD: pin may be driven or left floating RFU N.C. Functional Truth Table READ function Function Mode Standby Mode Byte Access (8 bits) Word Access (16 bits) Odd-Byte Only Access /CE2 /CE1 H H H L H L L L L H A0 X L H X X /OE X L L L L /WE X H H H H X L H X X X H H H H X L L L L Common Memory Attribute Memory /REG D15-D8 D7-D0 X High-Z High-Z H High-Z Even-Byte H High-Z Odd-Byte H Odd-Byte Even-Byte H Odd-Byte High-Z /REG D15-D8 D7-D0 X High-Z High-Z L High-Z Even-Byte L High-Z Not Valid L Not Valid Even-Byte L Not Valid High-Z WRITE function Standby Mode Byte Access (8 bits) Word Access (16 bits) Odd-Byte Only Access H H H L L August 2000 Rev. 4 - ECO #13125 H L L L H X H H H H 4 X X X Even-Byte X Odd-Byte Odd-Byte Even-Byte Odd-Byte X X L L L L X X X X X X Even-Byte X Even-Byte X PC Card Products PCMCIA Flash Memory Card FLA Series Absolute Maximum Ratings (1) Operating Temperature TA (ambient) Commercial Industrial Storage Temperature Commercial Industrial Voltage on any pin relative to VSS VCC supply Voltage relative to VSS 0C to +60 C -40C to +85 C -30C to +80 C -40C to +85 C -0.5V to VCC+0.5V -0.5V to +7.0V Note: (1) Stress greater than those listed under "Absolute Maximum ratings" may cause permanent damage to the device. This is a stress rating only and functional operation at these or any other conditions greater than those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. DC Characteristics (1) Symbol Parameter Density (Mbytes) All ICCR VCC Read Current ICCW VCC Program Current All ICCW VCC Program Current IPPW ICCE Notes Typ(3) Max Units Test Conditions 35 mA 75 mA All 28F008S5 28F016S5 28F008SA 30 mA VPP Program Current All Vpp=12V 30 mA VCC Erase Current All 100 mA 230 A VCC Standby Current ICCS (CMOS) 2MB 20MB 2MB 20MB 4MB 40MB 2 28F008SA 2 28F008S5 2 28F016S5 110 900 60 420 60 380 VCC = VCCmax tcycle = 150ns,CMOS levels VCC = VCCmax Control Signals = VCC Reset = VSS, CMOS levels CMOS Test Conditions: VCC = 5V 5%, VIL = VSS 0.2V, VIH = VCC 0.2V Notes: 1. All currents are RMS values unless otherwise specified. ICCR, ICCW and ICCE are based on Byte wide operations. For 16 bit operation values are double. 2. Control Signals: CE1#, CE2#, OE#, WE#, REG#. 3. Typical: VCC = 5V, T = +25C. Symbol Parameter Notes Min Max Units Test Conditions ILI Input Leakage Current 1 20 A VCC = VCCMAX Vin =VCC or VSS VCC = VCCMAX Vout =VCC or VSS ILO Output Leakage Current 1 20 A VIL Input Low Voltage 1 0 0.8 V VIH Input High Voltage 1 0.7VCC VCC+0.5 V VOL Output Low Voltage 1 0.4 V IOL = 3.2mA VOH Output High Voltage 1 VCC-0.4 VCC V IOH = -2.0mA VLKO VCC Erase/Program Lock Voltage 1 2.0 V Notes: 1. Values are the same for byte and word wide modes for all card densities. 2. Exceptions: Leakage currents on CE1#, CE2#, OE#, REG# and WE# will be < 500 A when VIN = GND due to internal pull-up resistors. Leakage currents on RST will be <150A when VIN=VCC due to internal pull-down resistor. August 2000 Rev. 4 - ECO #13125 5 PC Card Products PCMCIA Flash Memory Card FLA Series AC Characteristics Read Timing Parameters 150ns SYMBOL (PCMCIA) tC (R) Parameter Min Max Unit Read Cycle Time ta(A) Address Access Time 150 ns ta(CE) Card Enable Access Time 150 ns ta(OE) Output Enable Access Time 75 ns tsu(A) Address Setup Time 20 ns tsu(CE) Card Enable Setup Time 0 ns th(A) Address Hold Time 20 ns th(CE) Card Enable Hold Time 20 ns tv(A) 0 ns tdis(CE) Output Hold from Address Change Output Disable Time from CE# 75 ns tdis(OE) Output Disable Time from OE# 75 ns ten (CE) Output Enable Time from CE# 5 ns ten (OE) Output Enable Time from OE# 5 ns trec(RSR) Power Down recovery to Output Delay. VCC = 5V 150 ns 500 ns Note: AC timing diagrams and characteristics are guaranteed to meet or exceed PCMCIA 2.1 specifications. Read Timing Diagram tc(R ) th(A ) ta(A ) A [25 ::0], /R E G tv(A ) ta(C E ) tsu(C E ) /C E 1, /C E2 NOTE 1 NOTE 1 tsu(A ) ta(O E ) th(C E ) tdis(C E ) /O E tdis(O E ) ten (O E ) D [15 ::0] D A T A V A LID Note: Signal may be high or low in this area. August 2000 Rev. 4 - ECO #13125 6 PC Card Products PCMCIA Flash Memory Card FLA Series Write Timing Parameters 150ns SYMBOL (PCMCIA) tCW Parameter Min Max Unit Write Cycle Time 150 ns tw(WE) Write Pulse Width 80 ns tsu(A) Address Setup Time 20 ns tsu(A-WEH) Address Setup Time for WE# 100 ns tsu(CECard Enable Setup Time for WE# WEH) tsu(D-WEH) Data Setup Time for WE# 100 ns 50 ns th(D) Data Hold Time 20 ns trec(WE) Write Recover Time 20 ns tdis(WE) Output Disable Time from WE# 75 ns tdis(OE) Output Disable Time from OE# 75 ns ten(WE) Output Enable Time from WE# 5 ns ten(OE) Output Enable Time from OE# 5 ns tsu(OE-WE) Output Enable Setup from WE# 10 ns th(OE-WE) Output Enable Hold from WE# 10 ns tsu(CE) Card Enable Setup Time from OE# 0 ns th(CE) Card Enable Hold Time 20 ns Note: AC timing diagrams and characteristics are guaranteed to meet or exceed PCMCIA 2.1 specifications. Write Timing Diagram tc (W ) A [ 2 5 :: 0 ], / R E G ts u ( A - W E H ) tre c (W E ) ts u ( C E - W E H ) th (C E ) ts u (C E ) /C E 1 , /C E 2 NOTE 1 NO TE 1 /O E tw (W E ) ts u ( A ) th (O E -W E ) /W E th ( D ) ts u (O E -W E ) D [ 1 5 : :0 ] ( D in ) ts u (D -W E H ) NO TE 2 D A T A IN P U T t d is ( W E ) t d is ( O E ) te n (O E ) te n (W E ) D [ 1 5 ::0 ] ( D o u t ) NO TE 2 Notes: 1. Signal may be high or low in this area 2. When the data I/O pins are in the output state, no signals shall be applied to the data pins (D15 - D0) by the host system. August 2000 Rev. 4 - ECO #13125 7 PC Card Products PCMCIA Flash Memory Card FLA Series Data Write and Erase Performance (1,3) VCC = 5V 5%, TA = 0C to + 70C Symbol Parameter Notes tWHQV1 Word/Byte Program time tEHQV1 tWHQV2 Block Program Time tEHQV2 4 Block Erase Time Min Typ(1) Max 8 device SA device S5 device SA device S5 0.4 0.9 0.6 0.5 1.6 1.1 Units s 2.1 sec 10 sec Notes: 1. Typical: Nominal voltages and TA = 25C. 2. Excludes system overhead. 3. Valid for all speed options. 4. To maximize system performance RDY/BSY# signal should be polled. August 2000 Rev. 4 - ECO #13125 8 PC Card Products PCMCIA Flash Memory Card FLA Series PRODUCT MARKING WED 7P016FLA6200C15 C995 9915 EDI Date code Lot code / trace number Part number Company Name Note: Some products are currently marked with our pre-merger company name/acronym (EDI). During our transition period, some products will also be marked with our new company name/acronym (WED). Starting October 2000 all PCMCIA products will be marked only with the WED prefix. PART NUMBERING 7 P 016 FLA62 00 C 15 Card access time 15 25 150ns 250ns Temperature range C Commercial 0C to +70C I Industrial -40C to +85C Packaging option 00 Standard, type 1 Card family and version - See Card Family and Version Info. for details (next page) Card capacity 016 16MB PC card P R Standard PCMCIA Ruggedized PCMCIA Card technology 7 8 August 2000 Rev. 4 - ECO #13125 FLASH SRAM 9 PC Card Products PCMCIA Flash Memory Card FLA Series Card Family and Version Information FLA21-FLA24 FLA21 FLA22 FLA23 FLA24 Based on 28F008SA (requires 12V VPP for programming and erase functions) No Attribute Memory, no Write Protect With Attribute Memory, no Write Protect No Attribute Memory, with Write Protect With Attribute Memory, with Write Protect Example P/N 7P004FLA2200C15 FLA25-FLA28 FLA25 FLA26 FLA27 FLA28 Based on 28F008S5 for 5V only applications No Attribute Memory, no Write Protect With Attribute Memory, no Write Protect No Attribute Memory, with Write Protect With Attribute Memory, with Write Protect Example P/N 7P004FLA2600C15 FLA29-FLA32 FLA29 FLA30 FLA31 FLA32 Based on 28F016S5 for 5V only applications No Attribute Memory, no Write Protect With Attribute Memory, no Write Protect No Attribute Memory, with Write Protect With Attribute Memory, with Write Protect Example P/N 7P004FLA3000C15 FLA33-FLA36 FLA33 FLA34 FLA35 FLA36 Based on 28F004S5 for 5V only applications No Attribute Memory, no Write Protect With Attribute Memory, no Write Protect No Attribute Memory, with Write Protect With Attribute Memory, with Write Protect Example P/N 7P004FLA3600C15 FLA51-FLA54 FLA51 FLA52 FLA53 FLA54 Based on 28F008SA Similar to FLA21-FLA24: does not support registers and signals RST, RDY/BSY, Wait are not connected No Attribute Memory, no Write Protect With Attribute Memory, no Write Protect No Attribute Memory, with Write Protect With Attribute Memory, with Write Protect Example P/N 7P004FLA5200C15 FLA55-FLA58 FLA55 FLA56 FLA57 FLA58 Based on 28F008S5 Similar to FLA25-FLA28: does not support registers and signals RST, RDY/BSY, Wait are not connected No Attribute Memory, no Write Protect With Attribute Memory, no Write Protect No Attribute Memory, with Write Protect With Attribute Memory, with Write Protect Example P/N 7P004FLA5600C15 August 2000 Rev. 4 - ECO #13125 10 PC Card Products PCMCIA Flash Memory Card FLA Series FLA59-FLA62 FLA59 FLA60 FLA61 FLA62 Based on 28F016S5 Similar to FLA29-FLA32: does not support registers and signals RST, RDY/BSY, Wait are not connected No Attribute Memory, no Write Protect With Attribute Memory, no Write Protect No Attribute Memory, with Write Protect With Attribute Memory, with Write Protect Example P/N 7P004FLA6000C15 FLA63-FLA66 FLA63 FLA64 FLA65 FLA66 Based on 28F004S5 Similar to FLA33-FLA36: does not support registers and signals RST, RDY/BSY, Wait are not connected No Attribute Memory, no Write Protect With Attribute Memory, no Write Protect No Attribute Memory, with Write Protect With Attribute Memory, with Write Protect Example P/N 7P004FLA6600C15 August 2000 Rev. 4 - ECO #13125 11 PC Card Products PCMCIA Flash Memory Card FLA Series Ordering Information 7P XXX FLAYY SS T ZZ where XXX: 002 1) 004 006 1) 008 010 1) 012 014 1) 016 018 1) 020 024 2) 028 2) 032 2) 036 2) 040 2) 2MB 4MB 6MB 8MB 10MB 12MB 14MB 16MB 18MB 20MB 24MB 28MB 32MB 36MB 40MB 1) available only for FLA21-FLA24, FLA25-FLA28, FLA51-FLA54, and FLA55-FLA59 2) available only for FLA29-FLA32 and FLA59-FLA62 FLAYY: Card Family and Version (See Card Family and Version Information) SS: 00 01 02 WEDC Logo Silkscreen Blank Housing, Type I Blank Housing, Type I Recessed C I** Commercial Industrial 15 150ns T: ZZ: 0C to +70C -40C to +85C Notes: Options without attribute memory and with hardware write protect switch are available. ** Denotes advanced information. August 2000 Rev. 4 - ECO #13125 12 PC Card Products PCMCIA Flash Memory Card FLA Series CIS Information for FLA Series Cards Address Value Description Address Value 00H 01H CISTPL_DEVICE 30H F6H EDI TPLMID_MANF: LSB 02H 03H TPL_LINK 32H 01H EDI TPLMID_MANF: MSB 04H 53H FLASH = 150ns (device writable) 34H 00H LSB: Number Not Assigned 06H 06H CARD SIZE: 2MB 36H 00H MSB: Number Not Assigned 0EH 4MB 38H 15H 08H Description CISTPL_VERS1 16H 6MB 3AH 47H TPL_LINK 1EH 8MB 3CH 05H TPLLV1_MAJOR 26H 10MB 3EH 00H TPLLV1_MINOR 2EH 12MB 40H 45H E 36H 14MB 42H 44H D 3EH 16MB 44H 49H I 46H 18MB 46H 37H 7 4EH 20MB 48H 50H P 5EH 24MB 4AH 30H 0 6EH 28MB 4CH x 7EH 32MB 4EH x 8EH 36MB 50H 46H F 9EH 40MB 52H 4CH L FFH END OF DEVICE 54H 41H A 0AH 18H CISTPL_JEDEC_C 56H 32H 2 0CH 02H TPL_LINK 58H 32H 2 28F008SA 0EH 89H INTEL - ID 32H 2 based on 10H A2H INTEL 28F008SA - ID 36H 6 28F008S5 A6H INTEL 28F008S5 - ID 33H 3 based on AAH INTEL 28F016S5 - ID 30H 0 28F016S5 12H 17H CISTPL_DEVICE_A 5AH 2DH - 14H 03H TPL_LINK 5CH 2DH - 16H 42H EEPROM - 200ns 5EH 2DH - 18H 01H Device Size = 2KBytes 60H 31H 1 1AH FFH END OF TUPLE 62H 35H 5 based on 1CH 1EH CISTPL_DEVICEGEO 64H 20H SPACE 1EH 06H TPL_LINK 66H 00H END TEXT 20H 02H DGTPL_BUS 68H 43H C 22H 11H DGTPL_EBS 6AH 4FH O 24H 01H DGTPL_RBS 6CH 50H P 26H 01H DGTPL_WBS 6EH 59H Y 28H 01H DGTPL_PART 70H 52H R 2AH 01H FLASH DEVICE 72H 49H I NON-INTERLEAVED 74H 47H G 2CH 20H CISTPL_MANFID 76H 48H H 2EH 04H TPL_LINK(04H) 78H 54H T 7AH 20H SPACE August 2000 Rev. 4 - ECO #13125 13 PC Card Products PCMCIA Flash Memory Card FLA Series CIS Information for FLA Series Cards (Cont.) Address 7CH 7EH 80H 82H 84H 86H 88H 8AH 8CH 8EH 90H 92H 94H 96H 98H 9AH 9CH 9EH A0H A2H A4H A6H A8H AAH ACH AEH B0H B2H B4H B6H B8H BAH BCH BEH C0H C2H C4H C6H C8H CAH CCH CEH D0H D2H D4H D6H D8H DAH DCH Value 45H 4CH 45H 43H 54H 52H 4FH 4EH 49H 43H 20H 44H 45H 53H 49H 47H 4EH 53H 20H 49H 4EH 43H 4FH 52H 50H 4FH 52H 41H 54H 45H 44H 20H 00H 31H 39H 39H 37H 00H FFH 1AH 05H 01H 00H 00H 40H 03H 00H FFH 00H August 2000 Rev. 4 - ECO #13125 Description E L E C T R O N I C SPACE D E S I G N S SPACE I N C O R P O R A T E D SPACE END TEXT 1 9 9 7 END TEXT END OF LIST CISTPL_CONF TPL_LINK TPCC_SZ TPCC_LAST TPCC_RADR TPCC_RADR TPCC_RMSK NULL CONTROL TUPLE CISTPL_END INVALID ADDRESS 14 PC Card Products PCMCIA Flash Memory Card FLA Series Revision History: rev level description date rev 0 initial release May 26, 1998 rev 1 Logo change May 27, 1999 rev 2 Change in Ordering info: January 31, 2000 added FLA24, took "EDI" off of all part numbers, changed "EDI Silkscreen" to "WEDC Logo Silkscreen" rev 3 Heading/Logo changed and May 30, 2000 added to all pages Changes to Pages 1 & 12 Pages 9-11: Added Product Marking Info, added Family and Version Information, edited Ordering Info, edited General description and edited Architecture Overview rev 4 Corrected Errors on pgs. 6 & 7 August 1, 2000 White Electronic Designs Corporation One Research Drive, Westborough, MA 01581, USA tel: (508) 366 5151 fax: (508) 836 4850 www.whiteedc.com August 2000 Rev. 4 - ECO #13125 15 PC Card Products