LME49600 LME49600 High Performance, High Fidelity, High Current Audio Buffer Literature Number: SNAS422D LME49600 High Performance, High Fidelity, High Current Audio Buffer General Description Key Specifications The LME49600 is a high performance, low distortion high fidelity 250mA audio buffer. The LME49600 is designed for a wide range of applications. It can be used inside the feedback loop of op amps. The LME49600 offers a pin-selectable bandwidth: a low current, 110MHz bandwidth mode that consumes 7.3mA and a wide 180MHz bandwidth mode that consumes 13.2mA. In both modes the LME49600 has a nominal 2000V/s slew rate. Bandwidth is easily adjusted by either leaving the BW pin unconnected or connecting a resistor between the BW pin and the VEE pin. The LME49600 is fully protected through internal current limit and thermal shutdown. Low THD+N (VOUT = 3VRMS, f = 1kHz, Figure 2) Slew Rate 0.00003% (typ) 2000V/s (typ) High Output Current 250mA (typ) Bandwidth BW pin floating 110MHz (typ) BW connected to VEE 180MHz (typ) Supply Voltage Range 2.25V VS 18V Features Pin-selectable bandwidth and quiescent current Pure fidelity. Pure performance Short circuit protection Thermal shutdown TO-263 surface-mount package Applications Headphone amplifier output drive stage Line drivers Low power audio amplifiers High-current operational amplifier output stage ATE Pin Driver Buffer Power supply regulator Functional Block Diagram 30029805 FIGURE 1. Simplified Circuit Diagram (Note: I1 and I2 are mirrored from I) Boomer(R) is a registered trademark of National Semiconductor Corporation. (c) 2008 National Semiconductor Corporation 300298 www.national.com LME49600 High Performance, High Fidelity, High Current Audio Buffer March 31, 2008 LME49600 Connection Diagrams 300298a0 Top View Order Number LME49600TS See NS Package Number TS5B 30029832 Top View U -- Wafer fabrication code Z -- Assembly plant XY -- 2 Digit date code TT -- Lot traceability www.national.com 2 JA (Note 3) Soldering Information TO-263 Package (10 seconds) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage ESD Ratings(Note 4) ESD Ratings (Note 5) Storage Temperature Junction Temperature Thermal Resistance 20V 2000V 200V -40C to +150C 150C JC 65C/W Operating Ratings 20C/W 260C (Notes 1, 2) Temperature Range TMIN TA TMAX Supply Voltage -40C TA 85C 2.25V to 18V 4C/W System Electrical Characteristics for LME49600 The following specifications apply for VS = 15V, fIN = 1kHz, unless otherwise specified. Typicals and limits apply for TA = 25C. LME49600 Symbol IQ Parameter Total Quiescent Current Conditions IOUT = 0 BW pin: No connect BW pin: Connected to VEE pin Typical Limit (Note 6) (Note 7) 7.3 13.2 10.5 18 Units (Limits) mA (max) mA (max) AV = 1, VOUT = 3VRMS, RL THD+N SR Total Harmonic Distortion + Noise (Note 8) Slew Rate = 32, BW = 80kHz, closed loop see Figure 2. f = 1kHz f = 20kHz 0.000035 0.0005 % % 2000 V/s 100 110 MHz MHz 160 180 MHz MHz f = 10kHz BW pin: No Connect 3.0 nV/Hz f = 10kHz BW pin: Connected to VEE pin 2.6 nV/Hz 200 60 ns ns 30 BW 180MHz VOUT = 20VP-P, RL = 100 AV = -3dB BW pin: No Connect RL = 100 Bandwidth BW RL = 1k AV = -3dB BW pin: Connected to VEE pin RL = 100 RL = 1k Voltage Noise Density V = 10V, RL = 100 ts Settling Time 1% Accuracy BW pin: No connect BW pin: Connected to VEE pin VOUT = 10V AV Voltage Gain RL = 67 0.93 0.95 0.99 RL = 100 RL = 1k 3 0.90 0.92 0.98 V/V (min) V/V (min) V/V (min) www.national.com LME49600 JA Absolute Maximum Ratings (Notes 1, 2) LME49600 LME49600 Symbol VOUT Parameter Voltage Output Conditions Typical Limit Units (Limits) (Note 6) (Note 7) Positive IOUT = 10mA IOUT = 100mA IOUT = 150mA VCC -1.4 VCC -2.0 VCC -2.3 VCC -1.6 VCC -2.1 VCC -2.7 V (min) V (min) V (min) Negative IOUT = -10mA IOUT = -100mA IOUT = -150mA VEE +1.5 VEE +3.1 VEE +3.5 VEE +1.6 VEE +2.4 VEE +3.2 V (min) V (min) V (min) IOUT Output Current IOUT-SC Short Circuit Output Current BW pin: No Connect BW pin: Connected to VEE pin 490 490 550 mA (max) mA (max) IB Input Bias Current VIN = 0V BW pin: No Connect BW pin: Connected to VEE pin 1.0 3.0 2.5 5.0 A (max) A (max) ZIN Input Impedance RL = 100 BW pin: No Connect BW pin: Connected to VEE pin 7.5 5.5 VOS Offset Voltage VOS/C Offset Voltage vs Temperature 250 17 40C TA +125C 100 mA M M 60 mV (max) V/C Note 1: All voltages are measured with respect to ground, unless otherwise specified. Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature TA. The maximum allowable power dissipation is PDMAX = (TJMAX-TA)/JA or the number given in Absolute Maximum Ratings, whichever is lower. For the LME49600, typical application (shown in Figure 2) with VSUPPLY = 30V, RL = 32, the total power dissipation is 1.9W. JA = 20C/W for the TO-263 package mounted to 16in2 1oz copper surface heat sink area. Note 4: Human body model, 100pF discharged through a 1.5k resistor. Note 5: Machine Model, 220pF - 240pF discharged through all pins. Note 6: Typical specifications are specified at 25C and represent the parametric norm. Note 7: Tested limits are guaranteed to National's AOQL (Average Outgoing Quality Level). Note 8: This is the distortion of the LME49600 operating in a closed loop configuration with an LME49710. When operating in an operational amplifier's feedback loop, the amplifier's open loop gain dominates, linearizing the system and determining the overall system distortion. Note 9: The TSB package is non-isolated package. The package's metal back and any heat sink to which it is mounted are connected to the same potential as the -VEE pin. www.national.com 4 Gain vs Frequency vs Quiescent Current Phase vs Frequency vs Quiescent Current 30029899 30029881 Gain vs Frequency vs Power Supply Voltage Wide BW Mode Phase vs Frequency vs Supply Voltage Wide BW Mode 30029898 30029880 5 www.national.com LME49600 Typical Performance Characteristics LME49600 Gain vs Frequency vs Power Supply Voltage Low IQ Mode Phase vs Frequency vs Supply Voltage Low IQ Mode 30029897 30029879 Gain vs Frequency vs RLOAD Wide BW Mode Phase vs Frequency vs RLOAD Wide BW Mode 30029896 30029878 Gain vs Frequency vs RLOAD Low IQ Mode Phase vs Frequency vs RLOAD Low IQ Mode 30029895 30029877 www.national.com 6 LME49600 Gain vs Frequency vs CLOAD Wide BW Mode Phase vs Frequency vs CLOAD Wide BW Mode 30029894 30029875 Gain vs Frequency vs CLOAD Low IQ Mode Phase vs Frequency vs CLOAD Low IQ Mode 30029893 30029876 +PSRR vs Frequency VS = 15V, Wide BW Mode +PSRR vs Frequency VS = 15V, Low IQ Mode 30029889 30029891 7 www.national.com LME49600 +PSRR vs Frequency VS = 15V, Wide BW Mode +PSRR vs Frequency VS = 15V, Low IQ Mode 30029892 30029890 Quiescent Current vs Bandwidth Control Resistance THD+N vs Output Voltage VS = 15V, RL = 32, f = 1kHz Both channels driven 30029888 300298j4 High BW Noise Curve Low BW Noise Curve 30029845 www.national.com 30029846 8 LME49600 Typical Application Diagram 300298j5 FIGURE 2. High Performance, High Fidelity LME49600 Audio Buffer Application result is that the error signal (distortion) is amplified by a factor of 101. Although the amplifier's closed-loop gain is unaltered, the feedback available to correct distortion errors is reduced by 101, which means that measurement resolution increases by 101. To ensure minimum effects on distortion measurements, keep the value of R1 low as shown in Figure 3. This technique is verified by duplicating the measurements with high closed loop gain and/or making the measurements at high frequencies. Doing so produces distortion components that are within the measurement equipment's capabilities. This datasheet's THD+N and IMD values were generated using the above described circuit connected to an Audio Precision System Two Cascade. DISTORTION MEASUREMENTS The vanishingly low residual distortion produced by LME49710/LME49600 is below the capabilities of all commercially available equipment. This makes distortion measurements just slightly more difficult than simply connecting a distortion meter to the amplifier's inputs and outputs. The solution, however, is quite simple: an additional resistor. Adding this resistor extends the resolution of the distortion measurement equipment. The LME49710/LME49600's low residual distortion is an input referred internal error. As shown in Figure 3, adding the 10 resistor connected between the amplifier's inverting and non-inverting inputs changes the amplifier's noise gain. The 9 www.national.com LME49600 30029843 FIGURE 3. THD+N Distortion Test Circuit The audio input signal is applied to the input jack (HP31 or J1/J2) and dc-coupled to the volume control, VR1. The output signal from VR1's wiper is applied to the non-inverting input of U2-A, an LME49720 High Performance, High Fidelity audio operational amplifier. U2-A's AC signal gain is set by resistors R2, R4, and R6. To allow for a DC-coupled signal path and to ensure minimal output DC voltage regardless of the closedloop gain, the other half of the U2 is configured as a DC servo. By constantly monitoring U2-A's output, the servo creates a voltage that compensates for any DC voltage that may be present at the output. A correction voltage is generated and applied to the feedback node at U2-A, pin 2. The servo ensures that the gain at DC is unity. Based on the values shown in Figure 4, the RC combination formed by R11 and C7 sets the servo's high-pass cutoff at 0.16Hz. This is over two decades below 20Hz, minimizing both amplitude and phase perturbations in the audio frequency band's lowest frequencies. Application Information HIGH PERFORMANCE, HIGH FIDELITY HEADPHONE AMPLIFIER The LME49600 is the ideal solution for high output, high performance high fidelity head phone amplifiers. When placed in the feedback loop of the LME49710, LME49720 or LME49740 High Performance, High Fidelity audio operational amplifier, the LME49600 is able to drive 32 headphones to a dissipation of greater than 500mW at 0.00003% THD+N while operating on 15V power supply voltages. The circuit schematic for a typical headphone amplifier is shown in Figure 4. Operation The following describes the circuit operation for the headphone amplifier's Left Channel. The Right Channel operates identically. www.national.com 10 LME49600 30029858 FIGURE 4. LME49600 delivers high output current for this high performance headphone amplifier 11 www.national.com LME49600 Figure 6 shows the LME49600 connected as an open-loop buffer. The source impedance and optional input resistor, RS, can alter the frequency response. As previously stated, the power supplies should be bypassed with capacitors connected close to the LME49600's power supply pins. Capacitor values as low as 0.01F to 0.1F will ensure stable operation in lightly loaded applications, but high output current and fast output slewing can demand large current transients from the power supplies. Place a recommended parallel combination of a solid tantalum capacitor in the 5F to 10F range and a ceramic 0.1F capacitor as close as possible to the device supply pins. AUDIO BUFFERS Audio buffers or unity-gain followers, have large current gain and a voltage gain of one. Audio buffers serve many applications that require high input impedance, low output impedance and high output current. They also offer constant gain over a very wide bandwidth. Buffers serve several useful functions, either in stand-alone applications or in tandem with operational amplifiers. In standalone applications, their high input impedance and low output impedance isolates a high impedance source from a low impedance load. SUPPLY BYPASSING The LME49600 will place great demands on the power supply voltage source when operating in applications that require fast slewing and driving heavy loads. These conditions can create high amplitude transient currents. A power supply's limited bandwidth can reduce the supply's ability to supply the needed current demands during these high slew rate conditions. This inability to supply the current demand is further exacerbated by PCB trace or interconnecting wire inductance. The transient current flowing through the inductance can produce voltage transients. For example, the LME49600's output voltage can slew at a typical 2000V/s. When driving a 100 load, the di/dt current demand is 20 A/s. This current flowing through an inductance of 50nH (approximately 1.5" of 22 gage wire) will produce a 1V transient. In these and similar situations, place the parallel combination of a solid 5F to 10F tantalum capacitor and a ceramic 0.1F capacitor as close as possible to the device supply pins. Ceramic capacitors with values in the range of 10F to 100F, ceramic capacitor have very lower ESR (typically less than 10m) and low ESL when compared to the same valued tantalum capacitor. The ceramic capacitors, therefore, have superior AC performance for bypassing high frequency noise. In less demanding applications that have lighter loads or lower slew rates, the supply bypassing is not as critical. Capacitor values in the range of 0.01F to 0.1F are adequate. 30029860 FIGURE 6. Buffer Connections OUTPUT CURRENT The LME49600 can continuously source or sink 250mA. Internal circuitry limits the short circuit output current to approximately 450mA. For many applications that fully utilize the LME49600's current source and sink capabilities, thermal dissipation may be the factor that limits the continuous output current. The maximum output voltage swing magnitude varies with junction temperature and output current. Using sufficient PCB copper area as a heat sink when the metal tab of the LME49600's surface mount TO-263 package is soldered directly to the circuit board reduces thermal impedance. This in turn reduces junction temperature. The PCB copper area should be in the range of 3in2 (12.9cm2) to 6in2 (38.7cm2). SIMPLIFIED LME49600 CIRCUIT DIAGRAM The LME49600's simplified circuit diagram is shown in Figures 1 and 5. The diagram shows the LME49600's complementary emitter follower design, bias circuit and bandwidth adjustment node. THERMAL PROTECTION LME49600 power dissipated will cause the buffer's junction temperature to rise. A thermal protection circuit in the LME49600 will disable the output when the junction temperature exceeds 150C. When the thermal protection is activated, the output stage is disabled, allowing the device to cool. The output circuitry is enabled when the junction temperature drops below 150C. The TO-263 package has excellent thermal characteristics. To minimize thermal impedance, its exposed die attach paddle should be soldered to a circuit board copper area for good heat dissipation. Figure 7 shows typical thermal resistance from junction to ambient as a function of the copper area. The TO-263's exposed die attach paddle is electrically connected to the VEE power supply pin. 30029805 FIGURE 5. Simplified Circuit Diagram www.national.com 12 HIGH FREQUENCY APPLICATIONS The LME49600's wide bandwidth and very high slew rate make it ideal for a variety of high-frequency open-loop applications such as an ADC input driver, 75 stepped volume attenuator driver, and other low impedance loads. Circuit board layout and bypassing techniques affect high frequency, fast signal dynamic performance when the LME49600 operates open-loop. A ground plane type circuit board layout is best for very high frequency performance results. Bypass the power supply pins (VCC and VEE) with 0.1F ceramic chip capacitors in parallel with solid tantalum 10F capacitors placed as close as possible to the respective pins. Source resistance can affect high-frequency peaking and step response overshoot and ringing. Depending on the signal source, source impedance and layout, best nominal response may require an additional resistance of 25 to 200 in series with the input. Response with some loads (especially capacitive) can be improved with an output series resistor in the range of 10 to 150. OVERVOLTAGE PROTECTION If the input-to-output differential voltage exceeds the LME49600's Absolute Maximum Rating of 3V, the internal diode clamps shown in Figures 1 and 5 conduct, diverting current around the compound emitter followers of Q1/Q5 (D1 - D7 for positive input), or around Q2/Q6 (D8 - D14 for negative inputs). Without this clamp, the input transistors Q1/Q2 and Q5/Q6 will zener and damage the buffer. To ensure that the current flow through the diodes is held to a save level, the internal 200 resistor in series with the input limits the current through these clamps. If the additional current that flows during this situation can damage the source that drives the LME49600's input, add an external resistor in series with the input (see Figure 6). THERMAL MANAGEMENT BANDWITH CONTROL PIN The LME49600's -3dB bandwidth is approximately 110MHz in the low quiescent-current mode (7.3mA typical). Select this mode by leaving the BW pin unconnected. Connect the BW pin to the VEE pin to extend the LME49600's bandwidth to a nominal value of 180MHz. In this mode, the quiescent current increases to approximately 13.2mA. Bandwidths between these two limits are easily selected by connecting a series resistor between the BW pin and VEE . Regardless of the connection to the LME49600's BW pin, the rated output current and slew rate remain constant. With the power supply voltage held constant, the wide-bandwidth mode's increased quiescent current causes a corresponding increase in quiescent power dissipation. For all values of the BW pin voltage, the quiescent power dissipation is equal to the total supply voltage times the quiescent current (IQ * (VCC + |VEE |)). Heatsinking For some applications, the LME49600 may require a heat sink. The use of a heat sink is dependent on the maximum LME49600 power dissipation and a given application's maximum ambient temperature. In the TO-263 package, heat sinking the LME49600 is easily accomplished by soldering the package's tab to a copper plane on the PCB. (Note: The tab on the LME49600's TO-263 package is electrically connected to VEE.) Through the mechanisms of convection, heat conducts from the LME49600 in all directions. A large percentage moves to the surrounding air, some is absorbed by the circuit board material and some is absorbed by the copper traces connected to the package's pins. From the PCB material and the copper, it then moves to the air. Natural convection depends on the amount of surface area that contacts the air. If a heat conductive copper plane has perfect thermal conduction (heat spreading) through the plane's total area, the temperature rise is inversely proportional to the total exposed area. PCB copper planes are, in that sense, an aid to convection. These planes, however, are not thick enough to ensure perfect heat conduction. Therefore, eventually a point of diminishing returns is reached where increasing copper area offers no additional heat conduction to the surrounding air. This is apparent in Figure 7 as the thermal resistance reaches an asymptote above a copper area of 8in2). As can be seen, increasing the copper area produces decreasing improvements in thermal resistance. This occurs, roughly, at 4in2 of 1 oz copper board. Some improvement continues until about 16in2. Boards using 2 oz copper boards will have decrease thermal resistance providing a better heat sink compared to 1 oz. copper. Beyond 1oz or 2oz copper plane areas, external heat sinks are required. Ultimately, the 1oz copper area attains a nominal value of 20C/W junction to ambient thermal resistance (JA) under zero air flow. BOOSTING OP AMP OUTPUT CURRENT When placed in the feedback loop, the LME49600 will increase an operational amplifier's output current. The operational amplifier's open loop gain will correct any LME49600 errors while operating inside the feedback loop. To ensure that the operational amplifier and buffer system are closed loop stable, the phase shift must be low. For a system gain of one, the LME49600 must contribute less than 20 at the operational amplifier's unity-gain frequency. Various operating conditions may change or increase the total system phase shift. These phase shift changes may affect the operational amplifier's stability. Unity gain stability is preserved when the LME49600 is placed in the feedback loop of most general-purpose or precision op amps. When the LME46900 is driving high value capacitive loads, the BW pin should be connected to the VEE pin for wide bandwidth and stable operation. The wide bandwidth mode is also suggested for high speed or fast-settling operational amplifiers. This preserves their stability and the ability to faithfully amplify high frequency, fast-changing signals. Stability is ensured when pulsed signals exhibit no oscillations and ringing is minimized while driving the intended load and operating in the worst-case conditions that perturb the LME49600's phase response. 13 www.national.com LME49600 LOAD IMPEDANCE The LME49600 is stable under any capacitive load when driven by a source that has an impedance of 50 or less. When driving capacitive loads, any overshoot that is present on the output signal can be reduced by shunting the load capacitance with a resistor. LME49600 TRISE = TJ(MAX) - TA(MAX) Thus, if ambient temperature extremes force TRISE to exceed the design maximum, the part must be de-rated by either decreasing PD to a safe level, reducing JA further or, if available, using a larger copper area. Procedure 1. First determine the maximum power dissipated by the LME49600, PD(MAX). For the simple case of the buffer driving a resistive load, and assuming equal supplies, PD(MAX) is given by: 30029861 FIGURE 7. Thermal Resistance for 5 lead TO-263 Package Mounted on 1oz. Copper PDMAX(DC) = (IS x VS) + (VS)2 / RL (Watts) (3) 2. Determine the maximum allowable die temperature rise, Determining Copper Area Find the required copper heat sink area using the following guidelines: 1. Determine the value of the circuit's power dissipation, PD. 2. Specify a maximum operating ambient temperature, TA (MAX). (Note that the die temperature, TJ, will be higher than TA by an amount that is dependent on the thermal resistance from junction to ambient, JA). Therefore, TA must be specified such that TJ does not exceed the absolute maximum die temperature of 150C. 3. Specify a maximum allowable junction temperature, TJ (MAX), This is the LME49600's die temperature when the buffer is drawing maximum current (quiescent and load). It is prudent to design for a maximum continuous junction temperature of 100C to 130C. Ensure, however, that the junction temperature never exceeds the 150C absolute maximum rating for the part. 4. Calculate the value of junction to ambient thermal resistance, JA TRISE(MAX) = TJ(MAX) - TA(MAX) (C) 3. Using the calculated value of TRISE(MAX) and PD(MAX), find the required value of junction to ambient thermal resistance combining equation 1 and equation 4 to derive equation 5: JA = TRISE(MAX) / PD(MAX) Example Assume the following conditions: VS = |VEE| + VCC = 30V, RL = 32, IS = 15mA, sinusoidal output voltage, TJ(MAX) = 125 C, TA(MAX) = 85C. Applying Equation (2): PDMAX = (IS x VS) + (VS)2 / 22RL = (15mA)(30V) + 900V2 / 142 = 1.86W (1) Applying Equation (4): where: TJ(MAX) = the maximum recommended junction temperature TA(MAX) = the maximum ambient temperature in the LME49600's environment PD(MAX) = the maximum recommended power dissipation Note: The allowable thermal resistance is determined by the maximum allowable temperature increase: TRISE(MAX) = 125C - 85C = 40C Applying Equation (5): JA = 40C/1.86W = 21.5C/W www.national.com (4) 4. Finally, choose the minimum value of copper area from Figure 7 based on the value for JA. 5. JA as a function of copper area in square inches is shown in Figure 7. Choose a copper area that will guarantee the specified TJ(MAX) for the calculated JA. The maximum value of junction to ambient thermal resistance, JA, is defined as: (C/W) (2) where: VS = |VEE| + VCC (V) IS =quiescent supply current (A) Equation (2) is for sinusoidal output voltages and (3) is for DC output voltages A copper plane may be placed directly beneath the tab. Additionally, a matching plane can be placed on the opposite side. If a plane is placed on the side opposite of the LME49600, connect it to the plane to which the buffer's metal tab is soldered with a matrix of thermal vias per JEDEC Standard JESD51-5. JA= (TJ(MAX) - TA(MAX) )/ PD(MAX) PDMAX(AC) = (IS x VS) + (VS)2 / (22RL) (Watts) 14 dv/dt = IPK / CL (5) Output voltages with high slew rates will require large output load currents. For example if the part is required to slew at 1000V/s with a load capacitance of 1nF, the current demanded from the LME49600 is 1A. Therefore, fast slew rate is incompatible with a capacitive load of this value. Also, if CL is in parallel with the load, the peak current available to the load decreases as CL increases. SLEW RATE A buffer's voltage slew rate is its output signal's rate of change with respect to an input signal's step changes. For resistive 15 www.national.com LME49600 loads, slew rate is limited by internal circuit capacitance and operating current (in general, the higher the operating current for a given internal capacitance, the faster the slew rate). However, when driving capacitive loads, the slew rate may be limited by the available peak output current according to the following expression. Examining the Copper Area vs. JA plot indicates that a thermal resistance of 50C/W is possible with a 12in2 plane of one layer of 1oz copper. Other solutions include using two layers of 1oz copper or the use of 2oz copper. Higher dissipation may require forced air flow. As a safety margin, an extra 15% heat sinking capability is recommended. When amplifying AC signals, wave shapes and the nature of the load (reactive, non-reactive) also influence dissipation. Peak dissipation can be several times the average with reactive loads. It is particularly important to determine dissipation when driving large load capacitance. The LME49600's dissipation in DC circuit applications is easily computed using Equation (3). After the value of dissipation is determined, the heat sink copper area calculation is the same as for AC signals. LME49600 30029844 FIGURE 8. High Speed Positive and Negative Regulator www.national.com 16 LME49600 Revision History Rev Date 1.0 01/15/08 Initial release. Description 1.01 01/16/08 Edited specification table. 1.02 02/07/08 Edited applications information. 1.03 03/28/08 Text edits. 17 www.national.com LME49600 Physical Dimensions inches (millimeters) unless otherwise noted Order Number LME49600TS See NS Package TS5B www.national.com 18 LME49600 Notes 19 www.national.com LME49600 High Performance, High Fidelity, High Current Audio Buffer Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated