SINUMERIK
SINUMERIK Integrate
Analyze MyCondition (AMC),
Access MyMachine/Ethernet (AMM/E)
Installation Manual
Valid for control:
SINUMERIK 840D, SINUMERIK 840D sl/ 840DE sl
SINUMERIK 828D
Software
SINUMERIK Integrate, version 4.1 SP7
AMC, version 4.13 SP7
AMM/E, version 4.1 SP7
06/2017
A5E33520367B-AF
Preface
Fundamental safety
instructions 1
Introduction 2
Analyze MyCondition (AMC)
client setup 3
Access MyMachine/Ethernet
(AMM/E) client setup 4
Configuring ASC-SE/ASC-MO 5
Appendix A
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in
this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Division Digital Factory
Postfach 48 48
90026 NÜRNBERG
GERMANY
A5E33520367B-AF
Ⓟ 07/2017 Subject to change
Copyright © Siemens AG 2016 - 2017.
All rights reserved
Preface
SINUMERIK documentation
The SINUMERIK documentation is organized into the following categories:
● General documentation/catalogs
● User documentation
● Manufacturer/service documentation
Additional information
You can find information on the following topics at the following address (https://
support.industry.siemens.com/cs/de/en/view/108464614):
● Ordering documentation/overview of documentation
● Additional links to download documents
● Using documentation online (find and search in manuals/information)
If you have any questions regarding the technical documentation (e.g. suggestions,
corrections), please send an e-mail to the following address
(mailto:docu.motioncontrol@siemens.com).
mySupport/Documentation
At the following address (https://support.industry.siemens.com/My/ww/en/documentation),
you can find information on how to create your own individual documentation based on
Siemens' content, and adapt it for your own machine documentation.
Training
At the following address (http://www.siemens.com/sitrain), you can find information about
SITRAIN (Siemens training on products, systems and solutions for automation and drives).
FAQs
You can find Frequently Asked Questions in the Service&Support pages under Product
Support (https://support.industry.siemens.com/cs/de/en/ps/faq).
SINUMERIK
You can find information about SINUMERIK at the following address (http://www.siemens.com/
sinumerik).
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 3
Target group
This document addresses commissioning engineers and machine tool manufacturers. The
document provides detailed information that commissioning engineers require to commission
the SINUMERIK Integrate software.
Benefits
The software installation manual instructs the target group on how to install and uninstall the
software correctly.
Standard scope
This documentation describes the functionality of the standard scope. Additions or revisions
made by the machine manufacturer are documented by the machine manufacturer.
Other functions not described in this documentation might be executable in the control system.
This does not, however, represent an obligation to supply such functions with a new control
or when servicing.
For the sake of simplicity, this documentation does not contain all detailed information about
all types of the product and cannot cover every conceivable case of installation, operation, or
maintenance.
Security information on the product
Note
SINUMERIK Integrate
The SINUMERIK Integrate product is available as standalone (intranet) version or in cloud
operation (ASP).
● Standalone (intranet):
Read and write access to the file system and resources of the operating system of the
SINUMERIK Integrate server is enabled only for users with administrator rights.
● Cloud mode (ASP):
Siemens AG as operator ensures the security of the SINUMERIK Integrate server.
Customers must only ensure the security of the infrastructure on the machine side.
Further information about server operation can be found at Industrial Security Configuration
Manual (https://support.industry.siemens.com/cs/us/en/view/108862708).
Preface
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
4Installation Manual, 06/2017, A5E33520367B-AF
NOTICE
Misuse of data
It is essential to use secure data storage when saving your data - particularly your confidential
data. It is best to store this data encrypted locally or encrypted on the network. Make sure
that this data cannot be accessed by unauthorized personnel.
This applies to the following data:
● Archive files
● Image files
● Project files
● Trace files
● Safety-relevant files
Further information on secure data storage can be found at Industrial Security Configuration
Manual (https://support.industry.siemens.com/cs/us/en/view/108862708).
NOTICE
Danger due to insecure Internet connection
Before establishing a network connection, ensure your PC is connected to the Internet via a
secure connection. Pay attention to the security-relevant notes. Further information about
communications security can be found at Industrial Security Configuration Manual (https://
support.industry.siemens.com/cs/us/en/view/108862708).
NOTICE
Security risk through administrator rights
If you operate a PC with permanent administrator rights, there is an increased security risk.
Therefore, ensure that there is a secure operating environment, and assign administrator
rights only temporarily and selectively.
Further information on the secure administration of user accounts and the assignment of
rights can be found at Industrial Security Configuration Manual (https://
support.industry.siemens.com/cs/us/en/view/108862708).
EC Declaration of Conformity
The EC Declaration of Conformity for the EMC Directive can be found on the Internet at the
following address (https://support.industry.siemens.com/cs/https://
support.industry.siemens.com/cs/ww/de/ps/14604/certww/en/ps/13231/cert).
Preface
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 5
Preface
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
6Installation Manual, 06/2017, A5E33520367B-AF
Table of contents
Preface.........................................................................................................................................................3
1Fundamental safety instructions...................................................................................................................9
1.1 General safety instructions.......................................................................................................9
1.2 Warranty and liability for application examples......................................................................10
1.3 Industrial security...................................................................................................................11
2 Introduction.................................................................................................................................................13
2.1 Product overview....................................................................................................................13
2.2 Application areas and interaction...........................................................................................15
2.3 System preconditions.............................................................................................................17
3 Analyze MyCondition (AMC) client setup ..................................................................................................19
3.1 Overview................................................................................................................................19
3.2 Machine with SINUMERIK Operate.......................................................................................20
3.2.1 Display the "SINUMERIK Integrate" softkey..........................................................................20
3.2.2 Release applications..............................................................................................................20
3.2.3 Locking applications...............................................................................................................22
3.2.4 Installing the basis installation................................................................................................23
3.2.4.1 Basis installation, installing Installer.......................................................................................23
3.2.4.2 App installation, installing Base Setup...................................................................................24
3.2.5 Configuring proxy settings......................................................................................................28
3.2.6 Proxy authentication...............................................................................................................29
3.2.7 Configuring URL settings.......................................................................................................32
3.2.8 Uninstalling the basis installation...........................................................................................34
3.2.8.1 App installation, uninstalling Base Setup...............................................................................34
3.2.8.2 Basis installation, uninstalling Installer...................................................................................35
3.2.9 Client update of SINUMERIK Integrate..................................................................................36
3.2.9.1 Requirement...........................................................................................................................36
3.2.9.2 Client update under Windows................................................................................................36
3.2.9.3 Client update under Linux......................................................................................................40
3.3 Machine with HMI-Advanced.................................................................................................45
3.3.1 Installing SINUMERIK Integrate client...................................................................................45
3.3.2 Correcting connection problems............................................................................................57
3.3.3 Importing the root certificate...................................................................................................60
3.3.4 Configuring user-specific parameters - expert mode.............................................................65
3.3.4.1 Overview of the expert mode.................................................................................................65
3.3.4.2 Configuring URL settings.......................................................................................................66
3.3.4.3 Configuring Internet access...................................................................................................67
3.3.4.4 Selecting a driver...................................................................................................................71
3.3.4.5 Specifying data volumes and protocol settings......................................................................73
3.3.4.6 Specifying the target directory data buffering.........................................................................75
3.3.4.7 Changing the log file target directory.....................................................................................77
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 7
3.3.4.8 Changing the download method for the boot script................................................................79
3.3.4.9 Changing the start parameter client.......................................................................................81
3.3.4.10 Changing the time synchronization between PLC and HMI...................................................83
3.3.5 Integrating the client setup as external applications..............................................................84
3.3.6 Changing, repairing and uninstalling programs......................................................................87
3.4 Machine PC............................................................................................................................93
3.4.1 Installing SINUMERIK Integrate client (IPC)..........................................................................93
3.5 Workstation PC....................................................................................................................108
3.5.1 Client setup .........................................................................................................................108
4 Access MyMachine/Ethernet (AMM/E) client setup..................................................................................109
4.1 Overview..............................................................................................................................109
4.2 Machine with SINUMERIK Operate.....................................................................................111
4.2.1 Installing the AMM/E SE......................................................................................................111
4.2.2 Installation/Update AMM/E SE (ASC-MO)...........................................................................111
4.2.3 Uninstalling AMM/E Service Client.......................................................................................114
4.3 Machine with HMI-Advanced...............................................................................................115
4.3.1 Teleservice Client-Update....................................................................................................115
4.3.2 Installation/Update AMM/E SE (ASC-MO)...........................................................................117
4.3.3 Configuring SINUMERIK Integrate client.............................................................................119
4.3.4 Uninstalling client setup.......................................................................................................133
4.4 Machine PC..........................................................................................................................136
4.4.1 Configuring SINUMERIK Integrate Client SE (IPC).............................................................136
4.5 Workplace PC......................................................................................................................149
4.5.1 Installing AMM/E Service Client SE Client-Setup................................................................149
4.5.2 Uninstalling AMM/E Service Client SE.................................................................................155
5 Configuring ASC-SE/ASC-MO.................................................................................................................157
5.1 Overview..............................................................................................................................157
5.2 Setting the log-on data.........................................................................................................158
5.3 Setting the file transfer.........................................................................................................159
5.4 Entering the address of a proxy server................................................................................161
5.5 Setting/changing the language.............................................................................................163
5.6 Setting the log file.................................................................................................................165
5.7 Activating functions..............................................................................................................167
A Appendix...................................................................................................................................................169
A.1 List of abbreviations.............................................................................................................169
A.2 Documentation overview SINUMERIK 840D sl....................................................................172
Index.........................................................................................................................................................173
Table of contents
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
8Installation Manual, 06/2017, A5E33520367B-AF
Fundamental safety instructions 1
1.1 General safety instructions
WARNING
Danger to life if the safety instructions and residual risks are not observed
If the safety instructions and residual risks in the associated hardware documentation are not
observed, accidents involving severe injuries or death can occur.
● Observe the safety instructions given in the hardware documentation.
● Consider the residual risks for the risk evaluation.
WARNING
Malfunctions of the machine as a result of incorrect or changed parameter settings
As a result of incorrect or changed parameterization, machines can malfunction, which in turn
can lead to injuries or death.
● Protect the parameterization (parameter assignments) against unauthorized access.
● Handle possible malfunctions by taking suitable measures, e.g. emergency stop or
emergency off.
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 9
1.2 Warranty and liability for application examples
The application examples are not binding and do not claim to be complete regarding
configuration, equipment or any eventuality which may arise. The application examples do not
represent specific customer solutions, but are only intended to provide support for typical tasks.
You are responsible for the proper operation of the described products. These application
examples do not relieve you of your responsibility for safe handling when using, installing,
operating and maintaining the equipment.
Fundamental safety instructions
1.2 Warranty and liability for application examples
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
10 Installation Manual, 06/2017, A5E33520367B-AF
1.3 Industrial security
Note
Industrial security
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens products and solutions only represent one component of such a
concept.
The customer is responsible for preventing unauthorized access to its plants, systems,
machines and networks. Systems, machines and components should only be connected to
the enterprise network or the internet if and to the extent necessary and with appropriate
security measures (e.g. use of firewalls and network segmentation) in place.
Additionally, Siemens’ guidance on appropriate security measures should be taken into
account. For more information about industrial security, please visit:
Industrial security (http://www.siemens.com/industrialsecurity).
Siemens’ products and solutions undergo continuous development to make them more secure.
Siemens strongly recommends to apply product updates as soon as available and to always
use the latest product versions. Use of product versions that are no longer supported, and
failure to apply latest updates may increase customer’s exposure to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed at:
Industrial security (http://www.siemens.com/industrialsecurity).
WARNING
Unsafe operating states resulting from software manipulation
Software manipulations (e.g. viruses, trojans, malware or worms) can cause unsafe operating
states in your system that may lead to death, serious injury, and property damage.
● Keep the software up to date.
● Incorporate the automation and drive components into a holistic, state-of-the-art industrial
security concept for the installation or machine.
● Make sure that you include all installed products into the holistic industrial security concept.
● Protect files stored on exchangeable storage media from malicious software by with
suitable protection measures, e.g. virus scanners.
Fundamental safety instructions
1.3 Industrial security
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 11
Fundamental safety instructions
1.3 Industrial security
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
12 Installation Manual, 06/2017, A5E33520367B-AF
Introduction 2
2.1 Product overview
Overview of the applications
As a whole, applications are available that completely cover all aspects of integrating machines
into your communication, engineering and production processes.
Harmonized to address your particular requirements, you can access the following applications
of SINUMERIK Integrate:
3URGXFWLYLW\LQVHUYLFH3URGXFWLYLW\LQSURGXFWLRQ$XWRPDWLRQLQSURGXFWLRQ6,180(5,.,QWHJUDWH0DQDJH0\3URJUDPV$FFHVV0\'DWD0DQDJH0\7RROV$QDO\]H0\3HUIRUPDQFH$QDO\]H0\&RQGLWLRQ$FFHVV0\0DFKLQH
Figure 2-1 Overview
Delivery format
The latest packages and further information on the applications are stored on PridaNet and
can be downloaded directly from there.
Client setup directory
The client setups can be found in the following directories:
AMC
Sinumerik_Integrate_Clients > SinInt > Operate > Version > Linux/Windows
or
Sinumerik_Integrate_Clients > SinInt > HMI_Advanced
AMM/E
The AMM/E Service Client Setup is located in the following directory:
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 13
Sinumerik_Integrate_Clients > AMM > AMM-ServiceClient-MO
Regular software updates
The security patches regularly supplied by Microsoft are checked by the Cloud mode (ASP)
operator for compatibility with the current version of SINUMERIK Integrate by way of an internal
system test and are then released. An overview of the patch compatibility is generally given
shortly after the release of the security patch on the Service & Support Portal of Siemens
Industry Automation and Drive Technologies.
Additional software
SINUMERIK Integrate additionally uses the following software:
Software that was developed for "OpenSSL" to use the "OpenSSL Toolkit" (http://
www.openssl.org/)
.
Software that was developed for "Openevidence" to use the "OpenEvidence Toolkit" (http://
www.open-evidence.com/about/).
Cryptographic software written by Eric Young (eay@cryptsoft.com)
.
Software written by Tim Hudson (tjh@cryptsoft.com).
Software developed by Bodo Moeller.
Example: Remote access Access MyMachine (AMM/E)
,QWHJUDWH6HUYHUIDUP,QWHJUDWH&OLHQW+0,$GYDQFHG,QWHJUDWH&OLHQW6,180(5,.2SHUDWH3&8,QGXVWULDO(WKHUQHWKWWSVKWWSV
Figure 2-2 Overview AMM/E
Introduction
2.1 Product overview
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
14 Installation Manual, 06/2017, A5E33520367B-AF
2.2 Application areas and interaction
In order to integrate machine tools into SINUMERIK Integrate, various server and client setups
are required, depending on the computer version.
Note
Combining SINUMERIK Integrate applications
● A machine can only be connected with one server. It is not possible to distribute applications
across various servers (Siemens and local servers).
● Parallel operation with the MindApp "Manage MyMachines" is not possible.
SINUMERIK Integrate in Cloud mode (ASP)
This server is provided by Siemens and need not be installed on the customer’s premises. The
software functions are retrieved via the Internet and global telecommunication infrastructures.
The following section gives an overview of server/client installations if SINUMERIK Integrate
is operated via the Siemens server.
,
Q
W
H
U
Q
H
W
6
L
H
P
H
Q
V
6
H
U
Y
H
U
/RNDOHV1HW]ZHUN0DVFKLQH$UEHLWVSODW]3&6,180(5,.2SHUDWH+0,$GYDQFHG0DVFKLQHQ3&6HUYHU&OLHQW,QVWDOODWLRQVHSDUDWH,QVWDOODWLRQQLFKWHUIRUGHUOLFK$00($0&$00($0&$00($0&$00($0&
Introduction
2.2 Application areas and interaction
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 15
Installation
Clients can be installed in different ways:
Client installation:
● Installation via network
● Installation via USB interface
Client installation
You must install the appropriate clients, depending on the version of your PC, IPC or machine.
You can install the client as follows:
● Via PridaNet
● Via the USB interface
The following overview table shows which client setup is required on IPCs, PCs and machines.
Analyze MyCondition
(AMC)
Machine with SINUMERIK Operate
Basic installation:
Installer
Base Setup
X
Client setup
SINUMERIK Integrate (SI)
X
Machine with HMI-Advanced
Client setup
SINUMERIK Integrate (SI)
X
Machine PC (IPC)
Client setup
SINUMERIK Integrate (SI)
X
Workplace PC
Client setup
SINUMERIK Integrate (SI)
X
Introduction
2.2 Application areas and interaction
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
16 Installation Manual, 06/2017, A5E33520367B-AF
2.3 System preconditions
To operate SINUMERIK Integrate Analyze MyCondition or SINUMERIK Integrate Access
MyMachine/Ethernet, it is essential that the system requirements listed in the tables below are
fulfilled depending on their user version. The use of SINUMERIK Integrate Analyze
MyCondition or SINUMERIK Integrate Access MyMachine/Ethernet under different basic
conditions is explicitly not supported!
NOTICE
Operational safety jeopardized
If the system requirements are not observed, functional restrictions may occur. This may also
jeopardize operational safety!
Hardware and software requirements
As a minimum, the following hardware and software requirements must be met:
Product SINUMERIK Integrate 4.1 SP7
Applications AMC 4.13 SP7 AMM/E 4.1 SP7 10)
Workplace PC
Processor at least 1-GHz processor
RAM (GB) min. 4
Free hard disk capacity (GB)1) min. 1
Operating systems Windows 7 SP1 (x64) Professional/Enterprise/Ultimate1)
Windows XP SP2 (x32) Professional
Windows XP Embedded (x32) SP3 Standard
Web browser
Microsoft Internet Explorer IE11 with Compatibility Mode
Machine PC
Processor 1 GHz processor
RAM (GB) 4
Free hard disk capacity (GB)1) 1
Operating systems Windows 7 SP1 (x64) Professional/Enterprise/Ultimate1)3)
Windows XP SP3 (x32) Professional
Web browser
Microsoft Internet Explorer9) IE10, IE11 with comp. mode
Databases -
Machine4)5)
SINUMERIK 840D sl
with SINUMERIK Operate
As of 2.6 SP1 HF57)
As of 2.7 / 4.4 SP4 HF2
As of 4.5 SP4
As of 4.7 SP2 HF1
Introduction
2.3 System preconditions
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 17
Product SINUMERIK Integrate 4.1 SP7
Applications AMC 4.13 SP7 AMM/E 4.1 SP7 10)
Hardware As of NCU 710.3
As of NCU 720.2
As of NCU 730.1
As of PCU 50.3 (Windows XP SP3 or higher)
SINUMERIK 840D
with HMI-Advanced6)
As of 7.3 SP3
Hardware As of PCU 50.38)
Free hard disk capacity Not specified
Database -
Screen resolution 640 x 480
800 x 600
1024 x 768
1280 x 768 (Ergoline Panel)2)
1280 x 1024
800 x 480 (16:9.6; TP 900)
1366 x 768 (16:9; WXGA (TV))
1280 x 800 (16:10; TP 1200)
1) The Aero desktop representation under Windows 7 is not supported.
2) Not released for SINUMERIK Operate 2.6.
3) Embedded operating systems are not supported.
4) The SINUMERIK software versions that can actually be used are verified within the framework of the Q-Gate.
5) No data regarding the processor and operating system, as these parameters are specified by the hardware components.
6) To increase the fault tolerance, a RAID1 system with two hard disks (73 GB each) is recommended.
7) Restricted functional scope for AMM Remote STEP 7 is NOT available for HMI-Advanced and SINUMERIK Operate under
Windows (PCU).
8) PCU 50.3 available with Windows XP SP3 or higher.
9) Only Internet Explorer 32-bit version has been released for the AMM Service Client MO.
10) SINUMERIK Integrate ASC-MO Client is available in Cloud mode (ASP) with Windows XP SP3 or higher and only with
SINUMERIK Integrate V04.01.07 or higher.
Introduction
2.3 System preconditions
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
18 Installation Manual, 06/2017, A5E33520367B-AF
Analyze MyCondition (AMC) client setup 3
3.1 Overview
Requirements
You require the following access authorization to install and uninstall client setups: Access
level 1 (password: machine manufacturer).
Overview
The following section describes the client installation of Analyze MyCondition (AMC) for the
following workplaces:
● Machine with SINUMERIK Operate (Page 20)
● Machine with HMI-Advanced (Page 45)
● Machine PC (Page 93)
● Workstation PC (Page 108)
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 19
3.2 Machine with SINUMERIK Operate
3.2.1 Display the "SINUMERIK Integrate" softkey
The softkey on the user interface to call SINUMERIK Integrate is activated by a display machine
data.
Procedure
1. At the control system, start the SINUMERIK Operate operating soft‐
ware.
2. Press the "Commissioning" and "Masch. data" softkeys.
3. Press the menu forward key and press the "Display MD" softkey.
4. Set the machine data
MD9108 $MM_SINUMERIK_INTEGRATE to "1".
The "SINUMERIK Integrate" softkey is displayed on the extended hor‐
izontal softkey bar.
- OR -
If you are working on a control with operating software up to V4.5.1,
the machine data is:
MD9108 $MM_ENABLE_EPS_SERVICES.
Set the machine data to "1."
The "ePS Network services" softkey is displayed on the extended hor‐
izontal softkey bar.
3.2.2 Release applications
When installing the applications for the first time, SINUMERIK Integrate is always stopped,
and you must enable the applications.
During operation on the controller, you have the possibility to stop SINUMERIK Integrate again,
see chapter: Locking applications (Page 22)
Procedure
1. SINUMERIK Operate is started.
2. Press the menu forward key and press the "SINUMERIK Integrate" softkey.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
20 Installation Manual, 06/2017, A5E33520367B-AF
If the softkey is not displayed in the horizontal bar, then you must first enable
the softkey, see chapter: Display the "SINUMERIK Integrate" softkey
(Page 20).
- OR -
If you are working on a control with operating software up to V4.5.1, the
softkey with the previous designation "ePS Network services" is displayed
instead of the "SINUMERIK Integrate" softkey.
The welcome window opens.
3. Press the "Settings" softkey.
The "Settings" window opens displaying the system status "Use LOCKED".
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 21
4. Press the "Enable use" softkey to activate SINUMERIK Integrate.
You obtain the safety prompt "Do you really want to enable the use of SIN‐
UMERIK Integrate applications?"
5. Press the "OK" softkey to confirm the confirmation prompt.
The use of SINUMERIK Integrate applications is enabled.
- OR -
Press the "Cancel" softkey.
The applications are not enabled, and the previous window is displayed.
3.2.3 Locking applications
You can stop SINUMERIK Integrate if you do not need the applications during operation at the
control system.
Procedure
1. The "Settings" window is displayed.
Use is enabled for SINUMERIK Integrate applications.
Select the "Inhibit use" softkey to inhibit the applications.
2. The following confirmation warning is displayed:
"Do you really wish to inhibit the use of SINUMERIK Integrate applica‐
tions?"
3. Select the "OK" softkey to confirm the confirmation warning.
- OR -
Select the "Cancel" softkey not to stop SINUMERIK Integrate.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
22 Installation Manual, 06/2017, A5E33520367B-AF
4. After the applications have been inhibited, the following message is dis‐
played in the "Settings" window: "SINUMERIK Integrate use LOCKED".
5. Then restart the control system.
3.2.4 Installing the basis installation
3.2.4.1 Basis installation, installing Installer
Requirement
The use of SINUMERIK Integrate applications must be enabled.
Procedure
1. The "Settings" window is displayed.
Press the "Basic Installation" softkey.
An appropriate status message is displayed as to whether the basic instal‐
lation has already been installed.
If the basic installation is not yet performed, press the "Install" softkey.
2. The "Select Basic Installation" window opens and the directory overview is
displayed.
If the data is on a USB flash drive, for example, position the cursor on the
"installer_00_00_00_00.tar.gz" file. (In place of "00_00_00_00", the current
version is displayed.)
Press the "OK" softkey.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 23
3. An appropriate message pertaining to the selected software, its directory
and version is displayed.
Press the "OK" softkey to install the package.
- OR -
Press the "Cancel" softkey if you do not wish to install the selected package.
4. The installation is started, and the progress is displayed with a progress bar.
A message window is then displayed showing that the installation was suc‐
cessful.
The applications covered by the basic installation are displayed in the title
bar.
Press the "OK" softkey to complete the installation.
3.2.4.2 App installation, installing Base Setup
Requirements
The basic installation installer is installed.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
24 Installation Manual, 06/2017, A5E33520367B-AF
Installed applications
The installed applications are displayed as an overview in the "App Installation" window.
Function Description
Application name Installed application
Actual version Version number of the installed version.
In place of the current version, "00.00.00.000" is always displayed in the subse‐
quent illustrations.
Reference version Actual version (effective version = installed version) and reference version
(nominal version) match.
!Reference and actual versions do not match.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 25
Procedure
1. The "Settings" window is open and the use of SINUMERIK Integrate is
enabled.
Press the "App Installation" softkey.
2. The "App Installation" window is opened and shows the applications that
have already been installed.
3. Select the "Install" softkey.
The "Select Basic Installation" window is opened and a directory overview
is displayed.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
26 Installation Manual, 06/2017, A5E33520367B-AF
4. If the data is on a USB flash drive, for example, position the cursor on the
"basesetup_00_00_00_00.tar.gz" file (instead of "00_00_00_00_000", the
version currently installed on the control system is displayed).
Select the "OK" softkey.
5. A confirmation message is displayed, which you must confirm with the "OK"
softkey.
The installation is started, and the progress is displayed by way of a pro‐
gress bar.
6. Subsequently, an appropriate message is displayed as to whether the in‐
stallation was successful, and the installed application is displayed under
"Application is being installed."
Select the "OK" softkey.
The control system is restarted and activates the application.
7. The "App Installation" window is displayed with the applications that have
already been installed, specifying the version numbers. (In place of
"00.00.00.00.000", the current version is displayed.)
8. For additional information on the individual applications, select the appro‐
priate application and then the "Details" softkey.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 27
3.2.5 Configuring proxy settings
● Cloud mode (ASP): The settings for connection to the Siemens server are either fixed or
can be selected by default.
● Standalone (intranet): If you perform a local installation and are connected with the Internet
via a proxy server, you can individually adapt the proxy settings.
Requirement
The applications are installed.
You are using a machine with SINUMERIK Operate, as of version 4.5.3.
Proxy settings
Function Description
Proxy settings enabled Generally use proxy settings.
Directory The following directories are offered in the drop-down list:
● Siemens (data cannot be changed)
● OEM
● Addon
● User
Automatic The proxy settings are determined automatically.
Use proxy script Use the following proxy settings.
URL (proxy script) Individual address input of the proxy.
Use fixed proxy Use the following proxy settings.
Proxy 1
Proxy 2
Proxy 3
Specify a maximum of three proxy settings.
Direct Establish connection without proxy.
You can select for each setting by activating or deactivating the checkbox whether or not to
overwrite the entry.
Procedure
1. The "Settings" window is open.
Press the "Proxys>" softkey.
The current settings are displayed.
2. Press the "Edit" softkey to change the server access data.
Activate the "Overwrite here" checkbox to accept the new entry.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
28 Installation Manual, 06/2017, A5E33520367B-AF
3. Press the "OK" softkey.
A syntax check is performed and the access data is saved.
4. To enable the access data, restart the control system.
Example
You can enter only one script proxy and activate the general use in the user directory.
Additional entries are determined from the other directories.
3.2.6 Proxy authentication
To perform an authorization, you must enter the necessary proxy authentication data.
Introduction
The following proxy authentication procedures are supported:
NTLM - Microsoft Windows NT Challenge/Response authentication
For the NTLM authentication protocols, users are authenticated based on a challenge and
response mechanism. This mechanism proves to a server or domain controller that a user
knows the password that is linked to an account.
BASIC
The Basic Authentication as per RFC 2617 is the most common type of HTTP authentication:
A web server requests authentication. The application then searches for a user name /
password for this URL and possibly prompts the user. Then the application sends the
authentication with the authorization header in the form of the user name: Password Base64
encoded to the web server.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 29
KERBEROS
The Kerberos protocol is an authentication mechanism for identifying a user or host identity.
With the aid of the Kerberos protocol, a node can check at both ends of a network connection
to see whether the node on the other end is the entity that it is specified to be.
Note
Individual adaptation
Individually adapt the settings for the proxy authentication to the specific IT environments.
To do this, contact the responsible network operator / IT technician at the site of the machine
in order to get the necessary access data.
Authentication data
Function Description
Domain: Entry of a domain for a Microsoft Windows domain user.
User name: Entry of the user name for authentication on the proxy server.
Password: Entry of the password for authentication on the proxy server.
Workstation: Optional setting for an NTLM authorization proxy server.
Directory: Set authentication data for the desired level.
The default setting is "Siemens".
As with the data structure of SINUMERIK Operate, you can define settings for each
level.
● User
● OEM
● Addon
● Siemens
The various settings are merged.
Settings for "user" have priority over settings in "oem", etc.
The settings for "Siemens" represent the original state and cannot be changed.
By activating and deactivating the appropriate checkboxes, for each setting you can select
whether the entry should be overwritten.
Procedure
1. The "Settings" window is open.
Press the "Proxys>" softkey.
The current settings are displayed.
2. Press the "Credentials" softkey to enter the data for authenticating on the
proxy server.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
30 Installation Manual, 06/2017, A5E33520367B-AF
- OR -
Press the "Edit" softkey to change the data.
3. Select the desired level in the "Directories" drop-down list.
4. Activate the checkbox "Overwrite here" checkbox.
Activating overwriting
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 31
5. Now enter the data for the domain, user name, and password.
6. Press the "OK" softkey to save the settings.
- OR -
Press the "Cancel" softkey to close the window without accepting the
settings.
7. Restart the control so that the access data can take effect.
3.2.7 Configuring URL settings
The client requires three URLs to communicate with the server.
● Cloud mode (ASP): If you use SINUMERIK Integrate Server in cloud mode (ASP), all URLs
are preconfigured and you do not have to make any URL settings.
● Standalone (intranet): If you perform a local installation, you can individually adapt the URL
settings.
Requirement
The client setup has been completed.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
32 Installation Manual, 06/2017, A5E33520367B-AF
URL settings
Section Meaning
Directory The following directories are listed in a selection box:
● Siemens (data cannot be changed)
● OEM
● Addon
● User
Display homepage Individual addressing of the homepage
RenderService Individual address entry from Render Service.
Web service URL Individual addressing of the WebService, e. g.
http://<IP / Hostname>/mcis_if/MHComm/MHComm.asmx
Send timeout in ms Maximum permissible transmission time for sending in milliseconds
Note:
The entry of the timeout must be greater than 10 seconds.
Receive timeout in
ms
Maximum permissible transmission time for receiving in milliseconds.
Note:
The entry of the timeout must be greater than 10 seconds.
You can select for each setting by activating or deactivating the checkbox whether or not to
overwrite the entry.
Procedure
1. The "Settings" window is open.
Press the "URLs>" softkey.
The current settings are displayed.
2. Press the "Edit" softkey to change the server access data.
The new entry is accepted if you select the "Overwrite here" checkbox.
Example:
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 33
3. Press the "OK" softkey.
A syntax check is performed and the access data is saved.
4. To enable the access data, restart the control system.
3.2.8 Uninstalling the basis installation
3.2.8.1 App installation, uninstalling Base Setup
Procedure
1. Press the "App Installation" softkey.
The "App Installation" window is displayed with the applications that have
already been installed, specifying the version numbers. (In place of
"00.00.00.000", the current version is displayed on the control system.)
2.
Base Setup is selected. Press the "Uninstall" softkey.
3. The following confirmation warning is displayed: "Do you really want to un‐
install this application: Base Setup?"
Select the "OK" softkey to remove the package.
The progress is displayed by way of a progress bar.
- OR -
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
34 Installation Manual, 06/2017, A5E33520367B-AF
Select the "Cancel" softkey to cancel the uninstallation.
4. After the "Uninstallation was successful" message has been issued, restart
the control system.
To this end, select the "OK" softkey.
3.2.8.2 Basis installation, uninstalling Installer
Procedure
1. Select the "Basic Installation" softkey.
The installed version is displayed under "System status" (In place of
"00.00.00.00.000", the version currently installed on the control system is
displayed.)
2.
Select the "Uninstall" softkey.
3. The following confirmation warning is displayed: "Do you really want to de‐
lete the Basic Installation?".
Select the "OK" softkey to remove the package.
The progress is displayed by way of a progress bar.
- OR -
Select the "Cancel" softkey to cancel the uninstallation.
4. Upon completion of the process, the message "No Basic Installation cur‐
rently installed".
5. Restart the control system.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 35
3.2.9 Client update of SINUMERIK Integrate
3.2.9.1 Requirement
An update from the SINUMERIK Integrate Client is only supported as of SINUMERIK Operate
version 4.5.4.
If you upgrade SINUMERIK Operate from version 4.5.3 (or older) to version 4.5.4 (or later),
you must delete the existing service entries from the configuration file "systemconfiguration.ini"
manually.
The configuration file can be found in the following directories:
● Windows XP: F:\hmisl\user\sinumerik\hmi\cfg
● Windows 7: C:\Program Files (x86)\Siemens\MotionControl\user\sinumerik\hmi\cfg
● Linux: card/user/sinumerik/hmi/cfg
Procedure
1. Open the "systemconfiguration.ini" file.
2. Delete the following lines:
– SVC013 ...
– SVC014 ...
– SVC015 ...
– SVC017 ...
3. Save and close the file.
4. Delete the following files, if applicable:
– systemconfiguration.ini.453
– systemconfiguration.xml
3.2.9.2 Client update under Windows
Requirement
If not installed, install the PCU Base Software from 01.04.00.00 before starting the
SINUMERIK Integrate client update.
Procedure
1. Start the PCU in the Windows service mode.
2. Open the installation directory on the PCU.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
36 Installation Manual, 06/2017, A5E33520367B-AF
3. Start setup file "setup.exe" with a double-click.
SINUMERIK Integrate Client - InstallShield Wizard opens.
4. The welcome dialog opens and the current version number is displayed.
The installation language is English.
Click "Next >" to prepare for the installation.
5. The "License Agreement" window opens.
Read the license agreement.
– If you want to print the terms, click "Print."
– Then activate the "I accept the terms in the license agreement" checkbox and click "Next
>".
- OR -
Click "< Back" to return to the previous window.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 37
6. The next window displays the installation directory for the application.
Click "Next >" to accept the directory suggested by the setup.
7. The Wizard is ready to start the installation.
Click "Install" to start the installation.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
38 Installation Manual, 06/2017, A5E33520367B-AF
8. The installation is started, and the progress is displayed with a progress bar.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 39
9. Click "Finish" to complete the installation.
10.Finally, an overview of the applications that the client can use is shown.
3.2.9.3 Client update under Linux
Prerequisite
● Emergency Boot System as of Version 04.70.05.00
● SINUMERIK Operate as of Version 4.5 SP4
- OR -
● SINUMERIK Operate as of Version 4.7 SP2
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
40 Installation Manual, 06/2017, A5E33520367B-AF
Procedure
1. Copy the "sinintclient.tgz" file to the USB flash drive.
2. Insert the USB flash drive into the NCU.
3. Start the NCU.
4. In the menu, select "Update NCU Software and Data" with the cursor keys and press the
"OK" softkey.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 41
5. In the menu, select "Update system software from USB memory stick" with the cursor keys
and press the "OK" softkey.
6. You receive a list with all tgz files.
Select the current file.
Press the "OK" softkey to confirm your selection.
- OR -
Press the shortcut key <Shift> + <F8> on the operator panel.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
42 Installation Manual, 06/2017, A5E33520367B-AF
7. The selected file is displayed.
Press the "OK" softkey to confirm your selection.
- OR -
Press the shortcut key <Shift> + <F8> on the operator panel.
8. A confirmation prompt appears.
Press the "OK" softkey to confirm the confirmation prompt.
- OR -
Press the shortcut key <Shift> + <F7> on the operator panel.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 43
9. The installation is started.
10.When the installation has been completed, the following message appears.
Remove the USB flash drive.
Select "Restart" from the menu and press the "OK" softkey.
Analyze MyCondition (AMC) client setup
3.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
44 Installation Manual, 06/2017, A5E33520367B-AF
3.3 Machine with HMI-Advanced
3.3.1 Installing SINUMERIK Integrate client
The SINUMERIK Integrate client contains the setup of the application Analyze MyCondition
(AMC).
If the SINUMERIK Integrate Client has already been installed, then the system identifies the
scope of the installation. Compared to a new installation, several installation steps are skipped.
The procedure for installation for the first time is explained below.
Requirement
You have installed the appropriate Internet Explorer, see Section System preconditions
(Page 17).
Procedure
1. Start the PCU in the Windows service mode.
2. Open the installation directory on the PCU.
3. Start the "setup.exe" setup file by double-clicking.
– If you have not installed the appropriate Internet Explorer, a corresponding message is
displayed. For example, the program requires Internet Explorer 6 or higher.
The installation is aborted and you must first install the appropriate Internet Explorer.
Then restart the client installation.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 45
4. The welcome screen opens and displays the current version number (in place of "V.
0.0.0.00", the current version number is displayed on the control system).
The installation language is English.
Click "Next >" to prepare for installation.
5. The "License Agreement" window opens.
Read the license agreement.
– Click "Print" if you want to print out the conditions.
– Then activate the "I accept the terms of the license agreement" checkbox and click
"Next >".
- OR -
Click "< Back" to return to the previous window.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
46 Installation Manual, 06/2017, A5E33520367B-AF
6. You then have the option of selecting between two installation types:
– Standard mode
The preconfigured settings are used.
– Expert mode
The preconfigured settings can be changed to meet individual requirements.
Select "Standard mode" and click "Next >".
- OR -
Select "Expert mode (with additional installation options)" and click "Next >".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 47
7. The "Controller Configuration" window opens.
Select "SINUMERIK" and click "Next >".
8. The SINUMERIK connection types are displayed in the "Controller Configuration" window.
If you are working in a networked environment, select "HMI-Advanced and SINUMERIK
840D/Di or 810D + PCU50/70".
- OR -
If separately integrated, e.g. via HMI Pro, then select "SINUMERIK with own integration".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
48 Installation Manual, 06/2017, A5E33520367B-AF
9. Select the connection type in the next window:
– "1:1"
The function allows a direct connection to the machine.
– "1:N"
The function allows a connection in a group with several machines.
– "Flying HMI"
The function allows the use of SINUMERIK Integrate at machines, on which a client
cannot be installed, because the operating software of the machine does not support
this client. In this case, SINUMERIK Integrate is installed and configured on a workplace
PC or machine PC (IPC). PC/IPC and machine communicate via a (W)LAN connection.
Select connection type 1:1 and click "Next >".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 49
10.If you have selected the "Standard mode" installation type, then the "Reconfigurable
Parameters" window opens.
You can select the following configuration:
– "HMI softkey to start the product on the machine": After selecting this function, you can
define the softkey position on the user interface.
– "Internet proxy configurations": After selecting this function, you can enter the interface
to the Internet.
Click "Next >".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
50 Installation Manual, 06/2017, A5E33520367B-AF
11.If you select "HMI softkey to start the product on the machine", the "Available Hotkeys"
window opens.
From the drop-down list, select the position of the softkey with which you want to start the
application on the user interface.
Click "Next >".
- OR -
If you selected the "Expert mode" installation type under step ⑥, then the "Choose
Destination Location" window opens.
The installation directory is displayed.
If you want to use a different directory, click "Change..." and enter the required directory.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 51
12.If you want to change the default directory, the following confirmation warning is displayed:
– Click "Yes" to change the path.
- OR -
– Click "No" to cancel any changes.
13.If you selected the "Expert mode" installation type, then the "Reconfigurable Parameters"
window opens.
For the individual configuration options, see Section Configuring user-specific parameters
- expert mode (Page 65).
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
52 Installation Manual, 06/2017, A5E33520367B-AF
14.The "SINUMERIK Integrate URL Configuration" window opens.
Define the URLs of SINUMERIK Integrate, see Section Configuring URL settings
(Page 66)
15.In the following prompt, you are requested to check the address settings.
Confirm the prompt to check the Internet settings with "OK".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 53
16.The "Internet Properties" window opens.
The address is specified under the "General" tab in order to create the start page tabs.
Click the "Connections" tab to set up the Internet connection and to configure the LAN
settings, see Section Configuring Internet access (Page 67). Use the connection in your
company network that has already been set up.
Click "OK".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
54 Installation Manual, 06/2017, A5E33520367B-AF
17.The "Detected Internet Connection Settings" window opens and shows the actual settings.
Click "< Back" to correct the settings.
Click "Next >" to continue.
18.The settings are subject to an additional check, and an appropriate message is displayed
in the "Detected Internet Security Settings" window.
Click "< Back" to change the settings in the Internet Explorer.
- OR -
Activate the checkbox "Fix internet security settings" to permit the displayed settings.
Click "Next >" to continue.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 55
19.The "Start Copying Files" window opens and shows an overview of the settings that you
have made.
Click "Next >" to start the installation.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
56 Installation Manual, 06/2017, A5E33520367B-AF
20.The "Maintenance Complete" window opens.
Click "Finish" to complete the installation.
21.You are prompted to restart the system after the installation has been completed.
To do this, click "OK".
3.3.2 Correcting connection problems
Connection and synchronization problems between AMC and the control system with HMI-
Advanced can be caused by the following reasons:
● The OPC server is not registered
● HMI-Advanced version 07.06.02.08 or later
PCU Base Version earlier than 08.06.04
● The proxy configuration is faulty
● RSA certificate is not up-to-date
Requirement
You require administrator rights to make the following settings.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 57
Registering the OPC server
● Check whether the following registration has been entered:
"OPC.Sinumerik.Machineswitch".
If not, open the command line with administrator rights and start the following command:
F:\mmc2\opc\dataaccess\SOPC_MachineSwitch\RegServer\
● Then restart.
HMI-Advanced/PCU Base versions
If you work on a control system with HMI-Advanced version 07.06.02.08 or later, the OPC
server will be registered incorrectly and no current entries represented on the PC server.
1. Install the latest PCU base software or at least version 08.06.04.00
2. Then open the command line with administrator rights and start the following command: F:
\mmc2\opc\dataaccess\SOPC_MachineSwitch /RegServer
If you have a PCU Base version earlier than 08.06.04, then use DDE instead of OPC.
Set the value as follows:
1. Navigate to the following directory: F:\add_on\mh.
2. Open the "settings.ini" file with a text editor.
3. Search for the entry "ACCESSTYPE".
4. Change the value to "DDE".
Changing the proxy configuration
The problem occurs mainly on operating systems that are newer than Windows XP, e.g. with
Windows 7.
1. Adapt the standard configuration for Windows 7 as follows:
Open the path: HKEY_USERS\.DEFAULT\Software\Microsoft\Windows\CurrentVersion
\Internet Settings\Connections
2. Open the "Edit Binary Value" window.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
58 Installation Manual, 06/2017, A5E33520367B-AF
3. Change the value 09 to 03.
4. Start the service again. The connection is established.
RSA certificate not available/not up-to-date
For the SSL communication between server and machine, you require a certificate with 2048-
bit length. If you use a certificate with 1024-bit length, no connection is established between
server and client.
To establish a connection, install the following file: Ipins.exe
If the expiration date of VeriSign Class 3 International Server CA - G3 is 01/01/2014, the date
is updated by installing the "ipins.exe".
The file is located in the following directory: Sinumerik_Integrate_Clients/SinInt/
HMI_Advanced/Certificate\ipins.exe
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 59
3.3.3 Importing the root certificate
How to proceed under Windows
1. Open the Start menu and enter "mmc" in the input field.
2. Select "MMC" from the program menu.
The "Console1 - [Console Root]" window opens.
– From the "File" menu, select the function "Add/Remove Snap-in...".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
60 Installation Manual, 06/2017, A5E33520367B-AF
3. The "Add or Remove Snap-ins" window opens.
– From the "Available snap-ins:" list, select the "Certificates" snap-in.
– Click the "Add >" button.
4. The "Certificates snap-in" window opens.
– Select the "Computer account" option button.
– Click "Next >".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 61
5. The "Select Computer" window opens.
– Select the "Local computer: (the computer this console is Running on)" check box.
– Click the "Finish" button.
6. In the "Add or Remove Snap-ins" window, you will now see the following:
– The "Certificates (Local Computer)" snap-in is shown in the right-hand list "Selected
snap-ins:".
– Click "OK".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
62 Installation Manual, 06/2017, A5E33520367B-AF
7. The "Consol1 - ..." window opens.
– Open the following directory "Console Root" > "Certificates (Local Computer)" >
"Personal".
– Select "Certificates" and right click to open the menu.
– Select "All Tasks" and click the "Import..." function.
8. The "Welcome to the Certificate Export Wizard" window opens.
– Click "Next >" to start importing.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 63
9. The "File to Import" window opens.
– Click the "Browse..." button and select the directory that you want.
– Click "Next >".
10.The "Certificate Store" window opens.
– Select the "Place all certificates in the following store" option button.
– Click the "Browse..." button and select "Trusted Root Certification Authorities".
– Click "Next >".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
64 Installation Manual, 06/2017, A5E33520367B-AF
11.The "Completing the Certificate Import Wizard" window opens.
– A success message and an overview of the settings are displayed.
– Click the "Finish" button to complete the import.
12.Perform the same steps as are described above for all servers and Windows clients.
3.3.4 Configuring user-specific parameters - expert mode
3.3.4.1 Overview of the expert mode
The overview indicates the preconfigured settings, which you can change in the expert mode.
Expert mode
Table 3-1 Overview of the expert configuration
Function Default setting
1 Changing the URLs of the client IAC: https://www.epsnetwork.com/Services/HMI
MHComm: https:// www.epsnetwork.com/Services/MHC/Mhcomm.asmx
2 Configuration for the Internet access -
3 Size of the local data volume Maximum size (MB): 100
Maximum files: 5000
4 Directory path for data transfer C:\...\HMI-Advanced\add_on\temp\MhDtsTmp
5 Directory path, log file C:\...\HMI-Advanced\add_on\MH\log
6 Select download method, boot script Offline mode ON, no repeat attempts to download the boot script from the
server
7 Startup parameters ✔ Activate services
✔ Automatically start SINUMERIK Integrate Client on the machine at
startup
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 65
Function Default setting
8 Time synchronization between PLC and
HMI
TimeAdjustInterval 3600
TimeReadyOK 300
Note
Expert mode
If, in the "Installation mode" window, you select the "Expert mode" function, then the installation
wizard guides you through all of the options one after the other, which can be set in a user-
defined fashion.
You can save time if you install the client in the standard mode and then carry out all of the
user-defined settings.
See also
Configuring URL settings (Page 66)
Configuring Internet access (Page 67)
Selecting a driver (Page 71)
Specifying data volumes and protocol settings (Page 73)
Specifying the target directory data buffering (Page 75)
Changing the log file target directory (Page 77)
Changing the download method for the boot script (Page 79)
Changing the start parameter client (Page 81)
Changing the time synchronization between PLC and HMI (Page 83)
3.3.4.2 Configuring URL settings
You define the URLs of SINUMERIK Integrate using this function.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
66 Installation Manual, 06/2017, A5E33520367B-AF
SINUMERIK Integrate URLs
1. The "Reconfigurable parameters" window opens.
Activate the "SINUMERIK Integrate URLs" checkbox and click "Next >".
2. The "SINUMERIK Integrate URL configuration" window opens.
You define the URLs of SINUMERIK Integrate here.
For the address data, a distinction is made between a connection to the Siemens server
(Cloud mode (ASP)) or a connection to a local server (standalone (intranet)) within a
company network.
3.3.4.3 Configuring Internet access
You define the download method using this function.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 67
Internet proxy configurations
1. The "Reconfigurable Parameters" window is open.
Activate the "Internet proxy configurations" checkbox and click "Next >".
2. Confirm the note regarding checking the Internet settings with "OK".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
68 Installation Manual, 06/2017, A5E33520367B-AF
3. The "Internet Properties" window opens. Use the connection in your company network that
has already been setup and confirm the settings with "OK".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 69
4. Select the "Connections" tab.
Under LAN settings, click the button with the same name.
The "Local Area Network (LAN) Settings" window opens.
For the address data, a distinction is made between a connection to the Siemens server
(Cloud mode (ASP)) or a connection to a local server (standalone (intranet)) within a
company network.
Activate the "Use automatic configuration script" checkbox to use the automatic
configuration script.
Use a connection in your company network that has already been set up
Confirm your selection with "OK".
5. A window to check your settings opens.
Click "Next >".
- OR -
Change the settings by returning to the window that was previously displayed by clicking
"< Back".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
70 Installation Manual, 06/2017, A5E33520367B-AF
3.3.4.4 Selecting a driver
Use this function to specify the access method for data exchange.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 71
Generic Driver Support
1. The "Reconfigurable Parameters" window is open.
Activate the "Generic Driver Support" checkbox to define the server drivers. Click "Next >".
2. In the following window, under "Available Driver", you are given a selection of server drivers.
Select the corresponding driver.
In order to be able to address variable monitors, in the "Identifier (ProgID or CLSID)" entry
field, enter the ID of the selected driver. You can define the driver ID in the driver
documentation.
Confirm your change and click "Next >".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
72 Installation Manual, 06/2017, A5E33520367B-AF
3.3.4.5 Specifying data volumes and protocol settings
Using this function you define where data is saved if an Internet connection develops a fault.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 73
Data volumes and protocol settings
1. The "Reconfigurable Parameters" window is open.
Activate the "Data transfer area and logging settings" checkbox and click "Next >".
2. If there is an Internet connection fault during data transfer to the server, data is locally saved
in order to continue data transfer once the connection has been established again.
– In the entry field "Maximum size (MB)", enter a value between 0 and 2000 MB.
Recommendation:
20 MB (20971520 bytes) for Windows NT
50 MB (52428800 bytes) for Windows XP
– In the entry field "Maximum files" enter the maximum number of files that should be
locally saved.
– If you activate the "Enable limiting number of files for logging" checkbox, enter the
maximum number of files that should be saved in the log file at "Maximum files".
Confirm the settings and click "Next >".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
74 Installation Manual, 06/2017, A5E33520367B-AF
Option "MAXFILECOUNT"
In addition, you have the possibility of limiting the number of files in the directory "MHDTS"
using the option "MAXFILECOUNT" in the "settings.ini" file:
Example
[APP]
; Maximum directory size [byte]
MAXDIRSIZE = 104857600
; Maximum "*.DTS" files in folder, additionally "*.TMP" with same
amount.
MAXFILECOUNT = 1000
Note
Number of files
When setting the parameter, keep in mind that the total number of files will double because
the system creates the same number of * .DTS and * .TMP files.
3.3.4.6 Specifying the target directory data buffering
You define in which directory the data in operation is saved using this function.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 75
Data transfer area location
1. The "Reconfigurable Parameters" window is open.
Activate the "Data transfer area location" checkbox and click "Next >".
2. In the defined directory, all the data for operation is buffered until it is uploaded to the server.
Click "Browse..." to select a new, local target directory.
Confirm the change with "Next" >.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
76 Installation Manual, 06/2017, A5E33520367B-AF
Note
Restriction
It is not possible to buffer data in target directories that are located on network drives.
3.3.4.7 Changing the log file target directory
You define in which directory the log files are saved using this function.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 77
Log directory location
1. The "Reconfigurable Parameters" window is open.
Activate the "Log directory location" checkbox and click "Next >".
2. All log files are saved in the defined directory.
Click "Browse..." to select a new, local target directory for the log files.
Confirm the change and click "Next >".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
78 Installation Manual, 06/2017, A5E33520367B-AF
Note
Restriction
It is not possible to save log files in target directories, which are located on network drives.
3.3.4.8 Changing the download method for the boot script
You define the download method for the bootscript using this function.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 79
Bootscript download strategy
1. The "Reconfigurable Parameters" window is open.
Activate the "Bootscript download strategy" checkbox and click "Next >".
2. The following settings are available:
– "Offline mode ON, no repeated attempts to download the bootscript from the server"
A single attempt is made to load the bootscript from the server.
If there is no Internet connection, then the locally saved bootscript is used.
– "Offline mode OFF, the client performs repeated attempts to download the bootscript
from the server"
Several attempts are made to load the bootscript from the server.
If there is no Internet connection, a local bootscript is not used.
– "Offline mode OFF, no repeated attempts to download the bootscript from the server"
A single attempt is made to load the bootscript from the server.
If there is no Internet connection, then the locally saved bootscript is used.
Note
Offline mode OFF
If the "Offline mode OFF" option is set, alarms that occur are not buffered and are lost.
Select the preferred method to download the bootscript, by clicking the appropriate option field.
Click "Next >".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
80 Installation Manual, 06/2017, A5E33520367B-AF
3.3.4.9 Changing the start parameter client
You define the start properties of SINUMERIK Integrate Client using this function.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 81
SINUMERIK Integrate Client startup parameters
1. The "Reconfigurable Parameters" window is open.
Activate the "SINUMERIK Integrate Client startup parameter" checkbox and click "Next >".
2. The following settings are available:
– "Deferred startup of SINUMERIK Integrate Client"
SINUMERIK Integrate Client starts delayed by the specified time (0 - 300 s).
– "Slow internet connection"
The SINUMERIK Integrate Client delays establishing the Internet connection if there is
slow access (analog modem, ISDN, modem/router).
– "Start of SINUMERIK Integrate Client"
Activating/deactivating SINUMERIK Integrate.
Activating/deactivating the automatic start of the SINUMERIK Integrate Client when the
PCU, PC or PG powers up.
Activating/deactivating the welcome screen while SINUMERIK Integrate is loaded.
Select the start parameters and confirm your selection. Click "Next >".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
82 Installation Manual, 06/2017, A5E33520367B-AF
3.3.4.10 Changing the time synchronization between PLC and HMI
This function changes the time synchronization between the PLC and HMI.
Time master settings
1. The "Reconfigurable parameters" window opens.
Activate the "Time master settings" checkbox and click "Next >".
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 83
● If an alarm is output at the control system, this alarm is displayed with the PLC time.
Because the HMI and PLC time can deviate from one another, the operating software
provides a function to synchronize/align both of these times. This function is also used by
SINUMERIK Integrate.
An error message is displayed if you enter values that are too low.
– Activate the "Use HMI as time master" checkbox to activate time synchronization.
The entry fields to set the time intervals are enabled.
– For "TimeAdjustInterval" enter the time in seconds, which should elapse until the
difference between the HMI and PLC time is saved in the operating software. An error
message is displayed if you enter values that are too low.
– For "TimeReadOK", enter the time in seconds that should elapse until the next interval
for time synchronization starts.
An error message is displayed if you enter values that are too low.
Confirm the settings by clicking "Next >".
3.3.5 Integrating the client setup as external applications
Introduction
You have the option of calling the client setup from other applications, e.g. via TRANSLINE
2000 HMI PRO CS.
The call is configured via the TRANSLINE user interface.
Setup client with HMI-Advanced
Within the external application, a softkey must be configured, which starts the "iac.exe" file.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
84 Installation Manual, 06/2017, A5E33520367B-AF
Setup client without HMI-Advanced
Within the external application, the "MhCtrlr.exe" file must be configured as a background
process with the name "MhController".
Example: Setup client with HMI-Advanced
1. Select the menu "Configuration" and "Function keys".
The following window is opened.
– Under "New image", enter the softkey name, e.g. "EXE".
– Define the softkey position using the <Shift> key + right mouse click.
– In the selection list "HMI images", select the function "Integrate EXE.".
2. Make the other settings as follows:
– In the option field, select "Standard EXE".
– In the text field "Exe (path and file):" enter the following directory:
"f:\add_on\IAC.exe"
– In the text field "Windows title:" enter the title: "SINUMERIK Integrate"
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 85
Example: Setup client without HMI-Advanced
1. Select the menu "Configuration" and "Start background processes".
The following window is opened.
– In the text field "Exe (path and file):" enter the following directory:
"f:\add_on\MhCtrlr.exe".
– In the text field "Windows title" enter the following title: "MhController"
Note
It is not permissible that "MhCtrlr.exe" is started as background process, if the .exe is started
as background task by the Regie (administrator) (e.g. Task88).
While installing in the control, ensure that the following connection type is not selected:
"HMI-Advanced and SINUMERIK 840D/Di or 810D + PCU50/70".
2. Select the menu "File" and "Setting target computer", to configure the transfer of the project
to the target computer, e.g. to the PCU.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
86 Installation Manual, 06/2017, A5E33520367B-AF
– Select the menu "File" and "Installation of the system on PCU". The TRANSLINE system
is transferred to the selected PCU and installed on the PCU with the HMI PRO setup.
– Select the menu "File" and "Installation of the project on PCU". The TRANSLINE project
is transferred to the selected PCU and installed on the PCU with the HMI PRO setup.
3.3.6 Changing, repairing and uninstalling programs
In an existing client setup, you have the option of changing, repairing or uninstalling
installations.
Procedure
1. Start the PCU in the Windows service mode.
2. Open the installation directory.
3. Start the "setup.exe" setup file by double-clicking.
4. The "Welcome" window opens and offers you the following options:
– Changing the client setup
– Repairing the client setup
– Removing the client setup
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 87
Changing the client setup
1. In the "Welcome" window, select the "Reconfigure" function if you want to change the client
version.
2. The next steps are described in the following Section Installing SINUMERIK Integrate
client (Page 45).
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
88 Installation Manual, 06/2017, A5E33520367B-AF
Repairing the client setup
1. In the "Welcome" window, select the "Repair" function if applications are damaged and you
want to restore the initial state.
Click "Next >".
2. The "Setup Status" window opens and the operation is displayed on a progress indicator.
3. Click "Finish" to complete the installation.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 89
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
90 Installation Manual, 06/2017, A5E33520367B-AF
Removing the client setup
1. In the "Welcome" window, select the "Remove" function if you want to remove the client
setup.
Click "Next >".
2. A confirmation prompt appears.
Confirm this message with "Yes" if an additional application is installed and you want to
uninstall this application.
3. You may be shown an additional confirmation prompt asking, for example, whether you
wish to uninstall the Service Mode Client application.
Click "Yes" to start this operation.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 91
4. The uninstallation is started and the procedure is displayed on a progress indicator.
5. Click "Finish" to complete uninstalling.
Analyze MyCondition (AMC) client setup
3.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
92 Installation Manual, 06/2017, A5E33520367B-AF
3.4 Machine PC
3.4.1 Installing SINUMERIK Integrate client (IPC)
SINUMERIK Integrate Client includes the application Analyze MyCondition (AMC).
If the SINUMERIK Integrate client has already been installed, the system identifies the scope
of the installation. Compared to a new installation, several installation steps are skipped.
The procedure when installing for the first time is described below.
Procedure
1. Start the industrial PC (IPC) in Windows service mode.
2. Open the installation directory.
3. Start the "setup.exe" setup file by double-clicking.
4. The welcome dialog opens and displays the current version number (the current version
number is displayed for "V.0.0.0.00").
The installation language is English.
Click "Next >" to prepare for the installation.
Analyze MyCondition (AMC) client setup
3.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 93
5. The "License Agreement" window opens.
Read the license agreement.
– Click "Print" if you wish to print out the conditions.
– Then activate the "I accept the terms of the license agreement" checkbox and click
"Next >".
- OR -
Click "< Back" to return to the previous window.
Analyze MyCondition (AMC) client setup
3.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
94 Installation Manual, 06/2017, A5E33520367B-AF
6. You then have the option of selecting between two installation types:
– Standard mode
The preconfigured settings are used. You can only set that the Internet settings are
adapted using one option.
– Expert mode
The preconfigured settings can be changed to meet individual requirements.
Select "Standard mode" and click "Next >".
- OR -
Select "Expert mode (with additional installation options)" and click "Next >".
Analyze MyCondition (AMC) client setup
3.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 95
7. The "Controller Configuration" window opens.
Select "Industrial PC" and click "Next >".
Analyze MyCondition (AMC) client setup
3.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
96 Installation Manual, 06/2017, A5E33520367B-AF
8. If you selected the "Standard mode" installation type, the "Reconfigurable Parameters"
window opens.
Here, you can activate the "Internet proxy configurations" option if you wish to change the
Internet settings.
Click "Next >".
- OR -
If you selected "Expert mode" installation type, the "Choose Destination Location" window
opens.
The installation directory is displayed.
If you want to use a different directory, click "Change..." and enter the required directory.
Analyze MyCondition (AMC) client setup
3.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 97
9. If you selected the "Expert mode" installation type, the "Reconfigurable Parameters"
window opens.
For the individual configuration options, see Section Configuring user-specific parameters
- expert mode (Page 65)
Analyze MyCondition (AMC) client setup
3.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
98 Installation Manual, 06/2017, A5E33520367B-AF
10.The "SINUMERIK Integrate URL Configuration" window opens. You define the URLs of
SINUMERIK Integrate here.
In the following prompt, you are requested to check the address settings.
Confirm the prompt to check the Internet settings with "OK".
Analyze MyCondition (AMC) client setup
3.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 99
11.The "Internet Properties" window opens.
The address is specified under the "General" tab in order to create the start page tabs.
Click the "Connections" tab to set up the Internet connection and to configure the LAN
settings.
Click "OK".
Analyze MyCondition (AMC) client setup
3.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
100 Installation Manual, 06/2017, A5E33520367B-AF
12.The "Detected Internet Connection Settings" window opens and shows the current settings.
Click "< Back" to change the settings.
Click "Next >" to continue.
13.The settings are subject to an additional check, and an appropriate message is displayed
in the "Detected Internet Security Settings" window.
Click "< Back" to change the settings in the Internet Explorer.
- OR -
Click "Next >" to continue.
Analyze MyCondition (AMC) client setup
3.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 101
14.The "Generic Driver Support" window opens. Additional devices can be integrated here.
Select "OPC driver" and click "Next >".
15.The "Data Transfer Backup Area Location" window opens and shows the archive directory
for the transfer data.
Click "Browse..." if you want to create another directory.
Click "Next >" to continue.
Analyze MyCondition (AMC) client setup
3.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
102 Installation Manual, 06/2017, A5E33520367B-AF
16.The "Data Transfer Backup Area Location" window opens and shows the archive directory
for the temporary data.
Click "Browse..." if you want to create another directory.
Click "Next >" to continue.
17.The "Log Directory Location" window opens and shows the archive directory for the log data.
Click "Browse..." if you want to create another directory.
Click "Next >" to continue.
Analyze MyCondition (AMC) client setup
3.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 103
18.The "Data Transfer Area and Logging Settings" window opens. Here you define the data
storage during an Internet connection fault.
Enter the maximum data volume for the transfer data and click "Next >".
19.The "Boot Script Download Strategy" window opens.
You can select one of three different strategies for the download
Click "Next >".
Analyze MyCondition (AMC) client setup
3.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
104 Installation Manual, 06/2017, A5E33520367B-AF
20.The "Startup Parameter Configuration" window opens.
Select the start properties of the client.
Click "Next >".
21.The "Time Master Settings for the Machine" window opens. You can change the time
synchronization between the PLC and HMI.
Activate the "Use HMI as time master" checkbox to activate the time synchronization.
Click "Next >".
Analyze MyCondition (AMC) client setup
3.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 105
22.The "Start Copying Files" window opens and shows an overview of the settings that you
have made.
Click "Next >" to start the installation.
Analyze MyCondition (AMC) client setup
3.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
106 Installation Manual, 06/2017, A5E33520367B-AF
23.The "Maintenance Complete" window opens.
Click "Finish" to complete the installation.
24.You are prompted to restart the system after the installation has been completed.
To do this, click "OK".
Analyze MyCondition (AMC) client setup
3.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 107
3.5 Workstation PC
3.5.1 Client setup
A client installation is not required on a workstation PC.
Requirement
Only for standalone (intranet):
In order to set up users and machines on the local server, Internet Explorer is required on the
workplace PC.
To find out which Internet Explorer is suitable for your PC, see Section System preconditions
(Page 17).
References
Detailed information regarding the functions of AMC is provided in the following documentation:
Function Manual, SINUMERIK Integrate AMC.
Analyze MyCondition (AMC) client setup
3.5 Workstation PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
108 Installation Manual, 06/2017, A5E33520367B-AF
Access MyMachine/Ethernet (AMM/E) client setup 4
4.1 Overview
The Access Access MyMachine/Ethernet application is supported only for a separate
installation of Windows on a PCU 50 with HMI-Advanced.
For a control system with SINUMERIK Operate on NCU (Linux) or on the PCU (Windows), the
application is available without separate installation. The application functionality is installed
with the client installation of SINUMERIK Integrate.
In addition to the embedded AMM/E client, it is possible to use the AMM/E functions on
Windows control systems (as of XP SP3), provided the control system is in service mode, the
so-called AMM Service Client MO (ASC-MO).
Prerequisite for a client update
For a client update, the machine must be connected to the SINUMERIK Integrate Server.
Installation
Refer to the following sections regarding the installation:
● Machine with SINUMERIK Operate: Machine with SINUMERIK Operate (Page 111)
● PCU 50 with HMI-Advanced: Machine with HMI-Advanced (Page 115)
● Machine PC: Machine PC (Page 136)
● Workplace PC: Workplace PC (Page 149)
Client update
If remote access software is available on the control system, you can install the current AMM/
E application using an update.
For an update, the old version is automatically uninstalled and replaced by the current version.
If no predecessor version is available, "Update XY" is used to perform a client setup.
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 109
The current AMM/E application can be installed in the following ways:
● PCU 50 with HMI-Advanced:
– In SINUMERIK Integrate Client, the "Update Teleservice" function updates the AMM/E
functionality in SINUMERIK Integrate and the AMM/E Service Client MO, see Section
Teleservice Client-Update (Page 115)
– You can also use the "Update ASC-MO" function to update only the AMM/E Service
Client MO (ASC-MO), see Section Installation/Update AMM/E SE (ASC-MO)
(Page 117)
● NCU/PCU with SINUMERIK Operate:
– You can use only the Update function for AMM/E Service Client MO (ASC-MO), see
Section Installation/Update AMM/E SE (ASC-MO) (Page 111)
Access MyMachine/Ethernet (AMM/E) client setup
4.1 Overview
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
110 Installation Manual, 06/2017, A5E33520367B-AF
4.2 Machine with SINUMERIK Operate
4.2.1 Installing the AMM/E SE
If you operate a PCU 50 (Windows) or an NCU (Linux) with the "SINUMERIK Operate"
operating software, you do not require a separate installation.
The functionality is installed with the client installation of SINUMERIK Integrate, see Section
Machine with SINUMERIK Operate (Page 20).
If you want to use the AMM/E functionality on a PCU control system in service mode, you must
install the AMM/E Service Client MO beforehand, see Section Installation/Update AMM/E SE
(ASC-MO) (Page 111)
4.2.2 Installation/Update AMM/E SE (ASC-MO)
Before participating in a session, you require a current "AMM/E Service Client MO" client on
the control system with SINUMERIK Operate.
If the current version has already been installed, the "Update ASC-MO" softkey is not active.
If the prerequisite for the control system is not satisfied, i.e. Windows earlier than XP SP3 or
Linux, the "Update ASC-MO" softkey is not displayed.
The Access MyMachine Service Client MO (ASC-MO) offers the same AMM/E functionality
as the SINUMERIK Integrate Client. You can, however, use the ASC-MO when the control
system is in service mode, i.e. without the operating software running.
Requirement
You require a control system with Windows XP SP3 or later.
Procedure
1. Start "SINUMERIK Integrate" on the control system.
2. In the "Fault services" section, press the "Select" softkey.
The "Fault Services" window opens.
Access MyMachine/Ethernet (AMM/E) client setup
4.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 111
3. Press the "Update ASC-MO" softkey.
4. The client setup for AMM/E Service Client (ASC-MO) is downloaded in the background.
The client setup is loaded in the D:\Install directory by default.
The download is started and informs you about its progress.
Access MyMachine/Ethernet (AMM/E) client setup
4.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
112 Installation Manual, 06/2017, A5E33520367B-AF
5. You receive a success or error message on completion of the installation.
Press the "OK" softkey.
6. You can use AMM/E Service Client after a restart.
The procedure for making the settings is described in the following Section Configuring ASC-
SE/ASC-MO (Page 157)
Access MyMachine/Ethernet (AMM/E) client setup
4.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 113
4.2.3 Uninstalling AMM/E Service Client
Procedure
1. The "Add or Remove Programs" window opens.
Select the setup "Access MyMachine Service Client" and click the "Remove" button.
2. You receive a prompt whether you really want to remove "Access MyMachine Service
Client".
Click "No" to abort the operation.
Click "Yes" to start the uninstallation
3. The uninstallation is started and the procedure is displayed on a progress bar.
Access MyMachine/Ethernet (AMM/E) client setup
4.2 Machine with SINUMERIK Operate
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
114 Installation Manual, 06/2017, A5E33520367B-AF
4.3 Machine with HMI-Advanced
4.3.1 Teleservice Client-Update
Before participating in a session, you require a current "AMM/E Service Client MO" client on
the control system with HMI-Advanced.
If the current version has already been installed, the "Update Teleservice" softkey is not active.
If the prerequisite for the control system is not satisfied, i.e. Windows earlier than XP SP3 or
Linux, the "Update Teleservice" softkey is not displayed.
The "Update Teleservice" function updates the AMM/E functionality in SINUMERIK Integrate
client and the AMM/E Service Client MO.
Requirement
You require a control system with Windows XP SP3 or later.
Procedure
1. Start "SINUMERIK Integrate" on the control system.
2. In the "Fault services" section, press the "Select" softkey.
The "Fault Services" window opens.
3. Press the "Update Teleservice" softkey.
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 115
4. The client setup for Teleservice is downloaded in the background.
The client setup is loaded in the D:\Install directory by default.
The download is started and informs you about its progress.
5. You receive a success or error message on completion of the installation.
6. You can use the remote access function after a restart.
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
116 Installation Manual, 06/2017, A5E33520367B-AF
4.3.2 Installation/Update AMM/E SE (ASC-MO)
Before participating in a session, you require a current "AMM/E Service Client MO" client on
the control system with HMI-Advanced.
If the current version has already been installed, the "Update ASC-MO" softkey is not active.
If the prerequisite for the control system is not satisfied, i.e. Windows earlier than XP SP3 or
Linux, the "Update ASC-MO" softkey is not displayed.
The Access MyMachine Service Client MO (ASC-MO) offers the same AMM/E functionality
as the SINUMERIK Integrate Client. You can, however, use the ASC-MO when the control
system is in service mode, i.e. without the operating software running.
Requirement
You require a control system with Windows XP SP3 or later.
Procedure
1. Start "SINUMERIK Integrate" on the control system.
2. In the "Fault services" section, press the "Select" softkey.
The "Fault Services" window opens.
3. Press the "Update ASC-MO" softkey.
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 117
4. The client setup for AMM/E Service Client (ASC-MO) is downloaded in the background.
The client setup is loaded in the D:\Install directory by default.
The download is started and informs you about its progress.
5. You receive a success or error message on completion of the installation.
Press the "OK" softkey.
6. You can use AMM/E Service Client MO after a restart.
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
118 Installation Manual, 06/2017, A5E33520367B-AF
4.3.3 Configuring SINUMERIK Integrate client
If the SINUMERIK Integrate client has already been installed, then the system identifies the
scope of the installation. When compared to a new installation, several installation steps are
skipped.
The procedure is subsequently described if the SINUMERIK Integrate client setup was already
installed with another application, e.g. AMC and you wish to add the Access MyMachine/
Ethernet (AMM/E) application.
If you are installing for the first time, see Chapter: Installing SINUMERIK Integrate client
(Page 45).
Also see "Delivery form of the client setups" in Chapter: Product overview (Page 13)
Procedure
1. Start the PCU in the Windows service mode.
2. Open the installation directory.
3. Start the "ePS_Client_AT.exe" setup file with a double click.
4. The "Welcome" window opens.
The default installation language is English and offers you the following options:
– Changing the client setup
– Repairing the client setup
– Removing the client setup
Select "Reconfigure" and click "Next >".
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 119
5. You then have the option of selecting between two installation types:
– Standard mode
The preconfigured settings are used.
– Expert mode
The preconfigured settings can be changed to meet individual requirements.
Select "Standard mode" and click "Next >".
- OR -
Select "Expert mode (with additional installation options)" and click "Next >".
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
120 Installation Manual, 06/2017, A5E33520367B-AF
6. The "Additional Products" window opens if you use Windows XP SP3 or higher versions.
– Select "Access MyMachine for HMI Advanced" if you are installing AMM/E without the
service client.
- AND /OR -
– Select "Access MyMachine Service Client" to install the service client necessary for
remote access.
Click "Next >".
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 121
7. You will then receive a prompt whether you wish to make changes to the existing client
installation.
– Activate "NO - Do not prepare SINUMERIK Integrate client for series start-up" if you
want to keep the existing installation.
Click "Next >" to start the installation.
-OR-
Select "YES - Prepare SINUMERIK Integrate Client for Series start-up" if you wish to
change the parameter settings.
Click "Next >" to confirm the selection.
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
122 Installation Manual, 06/2017, A5E33520367B-AF
8. You obtain a confirmation prompt as to whether you wish to delete the directories that have
been created.
The directories are deleted if you confirm the prompt with "Yes".
You must now configure the parameters to address your requirements.
For the next steps, see step ⑨.
If you confirm the prompt with "No", the directories already installed are retained.
The installation is started and the procedure is displayed on a progress bar.
9. The "Reconfigurable Parameters" window opens.
A precise description of the configuration options can be found in Chapter Configuring user-
specific parameters - expert mode (Page 65)
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 123
10.The "SINUMERIK Integrate URL Configuration" window opens.
Define the URLs of SINUMERIK Integrate.
For the address data, a distinction is made between a connection to the Siemens server
or a connection to a local server within a company network.
If both the applications "Access MyMachine for HMI-Advanced" and "Access MyMachine
Service Client" are selected in the "Additional Products" window, then enter the following
URLs:
– Cloud mode (ASP) - Establish a connection to the local server:
Display home page: https://www.epsnetwork.com/services/HMI/
Render service: https://render.epsnetwork.com/IERenderService/
HandshakeService.asmx
Web service: https://www.epsnetwork.com/Services/MHC/MHComm.asmx
Click "Next >" to continue.
- OR -
If, in the "Additional Products" window, only "Access MyMachine Service Client" is selected,
enter the URLs "IAC" and "MHComm" depending on your server:
The window "SINUMERIK Integrate URL configuration" is opened.
– Cloud mode (ASP) - Establish a connection to the Siemens server:
IAC: https://www.epsnetwork.com/services/HMI/
IAC: MHComm: https://www.epsnetwork.com/Services/MHC/MHComm.asmx
– Standalone (intranet) - Establish a connection to the local server:
IAC: http://<servername or ip>/mcis_if/HMI
MHComm: http://<servername or ip>/mcis_if/MHComm/MHComm.asmx
IAC: https://www.epsnetwork.com/services/HMI/
IAC: MHComm: https://www.epsnetwork.com/Services/MHC/MHComm.asmx
Click "Next >" to continue.
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
124 Installation Manual, 06/2017, A5E33520367B-AF
11.In the following prompt, you are requested to check the address settings.
Confirm the prompt to check the Internet settings with "OK".
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 125
12.The "Internet Properties" window opens.
Enter the Internet connection and click the "OK" button.
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
126 Installation Manual, 06/2017, A5E33520367B-AF
13.The "Detected internet connection settings" message window opens and shows the actual
settings.
Click "< Back" to correct the settings.
Click "Next >" to continue.
14.The settings are subject to an additional check, and in the "Detected Internet Security
Settings" window you obtain an appropriate message.
Click "< Back" to change the settings in the Internet Explorer.
- OR -
Click "Next >" to continue.
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 127
15.The "Generic Driver Support" window opens. Additional devices can be integrated here.
Select "OPC driver" and click "Next >".
16.The "Data Transfer Backup Area Location" window opens and shows the archive directory
for the transfer data.
Click "Browse..." if you want to create another directory.
Click "Next >" to continue.
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
128 Installation Manual, 06/2017, A5E33520367B-AF
17.The "Data Transfer Area Location" window opens and shows the archive directory for the
temporary data.
Click "Browse..." if you want to create another directory.
Click "Next >" to continue.
18.The "Data Transfer Area Location" window opens and shows the archive directory for the
log data.
Click "Browse..." if you wish to create another directory.
Click "Next >" to continue.
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 129
19.The "Data Transfer Area and Logging Settings" window opens. Here you define the data
storage during an Internet connection fault.
Enter the maximum data volume for the transfer data and click "Next >".
20.The "Boot Script Download Strategy" window opens.
You can select one of three different strategies for the download
Click "Next >".
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
130 Installation Manual, 06/2017, A5E33520367B-AF
21.The "Startup Parameter Configuration" window opens.
Select the start properties of the client.
Click "Next >".
22.The "Time Master Settings for the Machine" window opens. You can change the time
synchronization between PLC and HMI.
Active the "Use HMI as time master" checkbox to activate time synchronization.
Click "Next >".
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 131
23.The "Start Copying Files" window opens and shows an overview of the settings that you
have made.
Click "Next >" to start the installation.
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
132 Installation Manual, 06/2017, A5E33520367B-AF
24.The "Maintenance Complete" window opens.
Click "Finish" to complete the installation.
25.You are prompted to restart the system after the installation has been completed.
To do this, click "OK".
4.3.4 Uninstalling client setup
You remove an existing client setup with the installed applications using the setup file
"ePS_Client_AT.exe".
Procedure
1. Start the PCU in the Windows service mode.
2. Open the installation directory.
3. Start the "ePS_Client_AT.exe" setup file with a double click.
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 133
4. The "Welcome" window opens.
The default installation language is English.
Select the "Remove" function to remove the client setup with the installed applications.
Click on "Next >".
5. A confirmation prompt appears.
Confirm the message with "OK" to start the uninstallation.
6. You obtain an additional confirmation prompt as to whether you wish to uninstall the Service
Mode Client.
Click "Yes" to start this operation.
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
134 Installation Manual, 06/2017, A5E33520367B-AF
7. The uninstallation is started and the procedure is displayed on a progress indicator.
8. Select whether you want to perform a restart immediately after completion of the
uninstallation or sometime later.
Click "Finish" to complete the uninstallation.
Access MyMachine/Ethernet (AMM/E) client setup
4.3 Machine with HMI-Advanced
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 135
4.4 Machine PC
4.4.1 Configuring SINUMERIK Integrate Client SE (IPC)
If the SINUMERIK Integrate client has already been installed, the system identifies the scope
of the installation. Compared to a new installation, several installation steps are skipped.
The procedure is subsequently described if the SINUMERIK Integrate client setup was already
installed with another application, e.g. AMC, and you wish to add the Access MyMachine/
Ethernet (AMM/E Service Client SE) application.
If you are installing for the first time, see Section: Installing SINUMERIK Integrate client (IPC)
(Page 93).
Procedure
1. Start the IPC in Windows service mode.
2. Open the installation directory.
3. Start the "setup.exe" setup file with a double click.
English is the default installation language.
4. The "Welcome" window opens and offers you the following options:
– Changing the client setup
– Repairing the client setup
– Removing the client setup
Select "Reconfigure" and click "Next >".
Access MyMachine/Ethernet (AMM/E) client setup
4.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
136 Installation Manual, 06/2017, A5E33520367B-AF
5. You then have the option of selecting between two installation types:
– Standard mode
The preconfigured settings are used.
– Expert mode
The preconfigured settings can be changed to meet individual requirements.
Select "Standard mode" and click "Next >".
- OR -
Select "Expert mode (with additional installation options)" and click "Next >".
Access MyMachine/Ethernet (AMM/E) client setup
4.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 137
6. The "Additional Products" window opens if you use Windows XP SP3 or higher versions.
Select "Access MyMachine Service Client" to install the service client necessary for remote
access.
Click "Next >".
Access MyMachine/Ethernet (AMM/E) client setup
4.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
138 Installation Manual, 06/2017, A5E33520367B-AF
7. You obtain a confirmation prompt as to whether you wish to make changes to the existing
client installation.
– Activate "NO - Do not prepare SINUMERIK Integrate Client for Series start-up" if you
want to keep the existing installation.
Click "Next >" to start the installation.
-OR-
Select "YES - Prepare SINUMERIK Integrate Client for Series start-up" if you wish to
change the parameter settings.
Click "Next >" to confirm the selection.
Access MyMachine/Ethernet (AMM/E) client setup
4.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 139
8. You obtain a confirmation prompt as to whether you wish to delete the directories that have
been created.
The directories are deleted if you confirm the prompt with "Yes".
You must now configure the parameters to address your requirements. For the next steps,
see step ⑥.
If you confirm the prompt with "No", the directories already installed are retained.
The installation is started and the procedure is displayed on a progress bar.
9. The "Reconfigurable Parameters" window opens.
A precise description of the configuration options can be found in Section: Configuring user-
specific parameters - expert mode (Page 65).
Access MyMachine/Ethernet (AMM/E) client setup
4.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
140 Installation Manual, 06/2017, A5E33520367B-AF
10.The "SINUMERIK Integrate URL Configuration" window opens.
You define the URLs of SINUMERIK Integrate here.
Enter the following URLs "IAC" and "MHComm" depending on your server.
– Cloud mode (ASP) - Establish a connection to the Siemens server:
IAC: https://www.epsnetwork.com/services/HMI/
IAC: MHComm: https://www.epsnetwork.com/Services/MHC/MHComm.asmx
– Standalone (intranet) - Establish a connection to the local server:
IAC: http://<servername or ip>/mcis_if/HMI
MHComm: http://<servername or ip>/mcis_if/MHComm/MHComm.asmx
Click "Next >" to continue.
11.In the following prompt, you are requested to check the address settings.
Confirm the prompt to check the Internet settings with "OK".
Access MyMachine/Ethernet (AMM/E) client setup
4.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 141
12.The "Internet Properties" window opens.
Enter the Internet connection.
Use the connection in your company network that has already been set up and click "OK".
Access MyMachine/Ethernet (AMM/E) client setup
4.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
142 Installation Manual, 06/2017, A5E33520367B-AF
13.The "Detected Internet Connection Settings" window opens and shows the actual settings.
Click "< Back" to correct the settings.
Click "Next >" to continue.
14.The settings are subject to an additional check, and an appropriate message is displayed
in the "Detected Internet Security Settings" window.
Click "< Back" to change the settings in the Internet Explorer.
- OR -
Click "Next >" to continue.
Access MyMachine/Ethernet (AMM/E) client setup
4.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 143
15.The "Generic Driver Support" window opens. Additional devices can be integrated here.
Select "OPC driver" and click "Next >".
16.The "Data Transfer Backup Area Location" window opens and shows the archive directory
for the transfer data.
Click "Browse..." if you want to create another directory.
Click "Next >" to continue.
Access MyMachine/Ethernet (AMM/E) client setup
4.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
144 Installation Manual, 06/2017, A5E33520367B-AF
17.The "Data Transfer Backup Area Location" window opens and shows the archive directory
for the temporary data.
Click "Browse..." if you want to create another directory.
Click "Next >" to continue.
18.The "Log Directory Location" window opens and shows the archive directory for the log data.
Click "Browse..." if you want to create another directory.
Click "Next >" to continue.
Access MyMachine/Ethernet (AMM/E) client setup
4.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 145
19.The "Data Transfer Area and Logging Settings" window opens. Here you define the data
storage during an Internet connection fault.
Enter the maximum data volume for the transfer data and click "Next >".
20.The "Boot Script Download Strategy" window opens.
You can select one of three different strategies for the download
Click "Next >".
Access MyMachine/Ethernet (AMM/E) client setup
4.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
146 Installation Manual, 06/2017, A5E33520367B-AF
21.The "Startup Parameter Configuration" window opens.
Select the start properties of the client.
Click "Next >".
22.The "Time Master Settings for the Machine" window opens.
You can change the time synchronization between the PLC and HMI.
Activate the "Use HMI as time master" checkbox to activate the time synchronization.
Click "Next >".
Access MyMachine/Ethernet (AMM/E) client setup
4.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 147
23.The "Start Copying Files" window opens and shows an overview of the settings that you
have made.
Click "Next >" to start the installation.
24.The "Maintenance Complete" window opens.
Click "Finish" to complete the installation.
25.After the installation has been completed, a restart is required.
Access MyMachine/Ethernet (AMM/E) client setup
4.4 Machine PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
148 Installation Manual, 06/2017, A5E33520367B-AF
4.5 Workplace PC
4.5.1 Installing AMM/E Service Client SE Client-Setup
The "ServiceClient_ServiceEng_Setup_32bit.exe" or
"ServiceClient_ServiceEng_Setup_64bit.exe" client setup is required for a remote access.
You have the following option of starting the client setup:
● Via online download.
- OR -
● Via a download saved on a storage medium / hard disk.
Requirement
Internet Explorer is installed on the workplace PC.
To find out which Internet Explorer is suitable for your PC, see Section: System
preconditions (Page 17).
Procedure
The system checks whether the necessary software has been installed when you start the
"Execute remote access" function.
Access MyMachine/Ethernet (AMM/E) client setup
4.5 Workplace PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 149
If the AMM/E Service Client has not yet been installed, the "Version Update" window opens.
1. Follow the instructions and click "OK" to start the installation.
2. The "File Download - Security Warning" window opens. English is the user interface
language.
You obtain the following data regarding setup:
– Name: Name of the setup
– Type: Type and size of the setup
– From: Specification of the Siemens server
Click "Save" to save the setup. You can initiate the installation later.
Click "Run" to start the download.
3. Once the download has been started, a further note with the following details appears:
– Name: Name of the setup
– Publisher: Specification of the Siemens server
Click "Run" to start the setup.
Access MyMachine/Ethernet (AMM/E) client setup
4.5 Workplace PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
150 Installation Manual, 06/2017, A5E33520367B-AF
4. The InstallShield wizard is started and displays which further Windows updates you require:
– Visual C++Redistributable 2015
– Microsoft .NET Framework 4.6.2
Click "Install" to start the pending updates.
Visual C++Redistributable 2015 is installed first.
5. Click "Install" again to start "Microsoft.NET Framework 4.6.2".
Access MyMachine/Ethernet (AMM/E) client setup
4.5 Workplace PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 151
6. The setup of ASC-SE is then prepared and the procedure is displayed on a progress bar.
7. The welcome screen opens and displays the current version number (in place of
"V0.0.0.00", the current version number is displayed).
Click "Next >" to prepare for installation.
Access MyMachine/Ethernet (AMM/E) client setup
4.5 Workplace PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
152 Installation Manual, 06/2017, A5E33520367B-AF
8. The "License Agreement" window opens.
Read the license agreement.
– Click "Print" if you want to print out the conditions.
– Then activate the "I accept the terms of the license agreement" checkbox and click
"Next >".
- OR -
Click "< Back" to return to the previous window.
Access MyMachine/Ethernet (AMM/E) client setup
4.5 Workplace PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 153
9. Select the installation directory.
Click "Next >" to accept the directory suggested by setup.
- OR -
Click "Change..." to change the installation directory.
10.Press "Install" to start the installation.
Remote STEP 7
Remote STEP 7 is only available with SINUMERIK Operate on Linux systems.
When using Remote STEP 7, with the setup of Service Client, the following files are
automatically copied to your computer:
● Windows XP: %WINDIR%\system32\remote_step7.dl
● Windows 7: %CommonProgramFiles%\Siemens\Automation\Simatic OAM\bin
\remote_step7.dll.
If the Service Client is installed on the PC without SIMATIC STEP 7, the setup must be repeated
if SIMATIC STEP 7 is subsequently installed.
Access MyMachine/Ethernet (AMM/E) client setup
4.5 Workplace PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
154 Installation Manual, 06/2017, A5E33520367B-AF
4.5.2 Uninstalling AMM/E Service Client SE
Procedure
1. The "Add or Remove Programs" window opens.
Select the setup "AMM/E Service Client SE" and click "Remove".
2. You receive a prompt whether you really want to remove "AMM/E Service Client SE".
Click "No" to abort the operation.
Click "Yes" to start the uninstallation
3. The uninstallation is started and the procedure is displayed on a progress bar.
Access MyMachine/Ethernet (AMM/E) client setup
4.5 Workplace PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 155
Access MyMachine/Ethernet (AMM/E) client setup
4.5 Workplace PC
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
156 Installation Manual, 06/2017, A5E33520367B-AF
Configuring ASC-SE/ASC-MO 5
5.1 Overview
You can make the following settings in Access MyMachine Service Client SE and in ASC-MO:
You can make the following settings in the "Settings" menu:
● Login..., see Section Setting the log-on data (Page 158).
● File transfer..., see Section Setting the file transfer (Page 159).
● Proxy..., see Section Entering the address of a proxy server (Page 161).
● Language..., see Section Setting/changing the language (Page 163).
● Logging..., see Section Setting the log file (Page 165).
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 157
5.2 Setting the log-on data
You can register your login data. Your data is then automatically set when logging in.
Settings Description
Server selection
AMM/E server Address of the Access MyMachine server.
User role
Service engineer Activate the appropriate role.
Machine operator
Login data
User name User data to log in to SINUMERIK Integrate.
Password
Organization
Note password If the function is activated, the password is stored in encoded form in the
system.
Session number
Display entry field for
the session number
when logging in.
If the function is activated, the entry fields for the session number are dis‐
played in the login window.
Procedure
1. Call "Settings" > "Login..." in the menu bar.
The "Login Settings" window opens.
2. Enter your required data.
Click "OK" to save the settings.
- OR -
Click "Cancel" to reject the settings.
Configuring ASC-SE/ASC-MO
5.2 Setting the log-on data
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
158 Installation Manual, 06/2017, A5E33520367B-AF
5.3 Setting the file transfer
You can log the actions in a file during a remote access. You specify the settings of the log file
in the "File Transfer Settings" window.
Settings Description
Temporary files
Directory: Specify the log directory or create a new directory in which the log files will
be stored
The directory selection is made in the "Find Directory" window.
Max. file size [KB]: Specify the maximum number of log files.
If "0" is entered, no log files are written. When the maximum number of files
is reached, the oldest log file is deleted.
Additional drive types
Removable drives The machine operator specifies which drive types the service engineer may
access. If no drive type is selected, the service engineer may only access
the available hard drives.
Remote/network drives
Procedure
1. Call "Settings" > "File transfer..." in the menu bar.
The "File Transfer Settings" window opens.
2. A standard directory is specified for the logs.
If you want to use another directory as log directory, you can specify that here, see "Find
directory / Create new directory" below.
3. Specify the maximum number of log files that can be saved in the log directory.
4. Then define which drive types are supported for the file transfer.
Activate the corresponding checkbox for each drive type that is to be supported.
5. Click "OK" to save the settings.
- OR -
Click "Cancel" to reject the settings.
Configuring ASC-SE/ASC-MO
5.3 Setting the file transfer
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 159
Find directory / Create new directory
1. Click "..." behind "Directory:" if you want to set a different directory than that specified.
The "Find Directory" window opens.
2. Select the required directory in the directory tree.
- OR -
Click "Create new directory" to create a new directory.
3. Click "OK" to specify the directory.
Configuring ASC-SE/ASC-MO
5.3 Setting the file transfer
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
160 Installation Manual, 06/2017, A5E33520367B-AF
5.4 Entering the address of a proxy server
If access to the Internet is done via a proxy server, define the desired method via the proxy
settings.
Setting Description
Do not use a proxy (direct connection) Establishes a direct connection to the Internet.
Automatic proxy detection Automatically determines the address of a proxy server for
access to the Internet from the network.
Use system proxy settings Uses the Internet Explorer settings for connection to the In‐
ternet.
Click "Internet options" to open the Internet options of the
system in order to check or change the proxy settings.
Use Manufacturing IT client proxy set‐
tings
Uses the settings of the Manufacturing IT client to gain ac‐
cess to the Internet.
Use automatic configuration script: Address input of the proxy server from which the proxy script
is downloaded.
Use these proxy settings (manual): Address input (address and port) of a specific proxy server.
Use these proxy credentials: Input of the access data if the proxy server requires a login.
Remember authentication data The access data is stored retentively in the system.
The password is stored in encoded form.
Procedure
1. Call "Settings" > "Proxy..." in the menu bar.
The "Proxy settings" window opens.
2. Select the desired proxy setting.
If you are using your own proxy login data, activate the "Use these proxy settings (manual):"
checkbox.
]Then activate the checkbox "Use these proxy credentials:" and enter your username and
password.
Configuring ASC-SE/ASC-MO
5.4 Entering the address of a proxy server
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 161
3. Activate the "Remember authentication data" checkbox if you want to save your login data
permanently.
4. Click "OK" to save the settings.
- OR -
Click "Cancel" to reject the settings.
Configuring ASC-SE/ASC-MO
5.4 Entering the address of a proxy server
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
162 Installation Manual, 06/2017, A5E33520367B-AF
5.5 Setting/changing the language
The displayed language can be changed during a session in two different ways:
● Via the "Languages" menu.
● Via the key combination <Ctrl> and <L>.
However, you must define the two "preferred" languages for this beforehand, see below:
Setting the language changeover.
Changing the language
You can change the currently displayed language.
1. Open the "Languages" menu.
All the available languages are displayed. The current language is marked.
2. Check the checkbox for the desired language.
The user interface is changed and displays the texts in the corresponding language.
Configuring ASC-SE/ASC-MO
5.5 Setting/changing the language
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 163
Setting the language changeover
To ensure that you can quickly change to another language during a session using the key
combination <Ctrl> + <L>, you must first specify the two preferred languages.
1. Call "Settings" > "Language..." in the menu bar.
2. The "Toggle language" window opens.
Select the favorited languages.
3. Click "OK" to save the selection.
- OR -
Click "Cancel" to reject the selection.
Configuring ASC-SE/ASC-MO
5.5 Setting/changing the language
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
164 Installation Manual, 06/2017, A5E33520367B-AF
5.6 Setting the log file
A log file is frequently required for diagnostic purposes. You can activate the creation of a log
file and make further settings for the file.
Setting Description
Configuration
Activate logging Switches the log functionality on/off.
Activate diagnostics
logging
Performs the logging with an increased log level and a greater maximum file
size. More data is therefore available for diagnostic purposes. In this mode, the
user cannot specify the maximum file size or a log level, because these values
are specified by AMM/E.
Directory: Defines or creates a directory in which the log files are stored. The directory is
created in the "Find Directory" window.
Max. file size [KB] Specification of the maximum file size in KB. AMM/E creates a maximum of two
log files. As soon as the first file reaches the maximum size, a new log file is
created. If an older file is already available, it is overwritten.
Log level Specifies whether and which data is to be logged.
None Do not log any data.
Fatal Fatal error that prevents the further program execution.
Error Simpler errors that occur during the program execution, but that do not prevent
further execution.
Warning Warnings that may indicate problems.
Info Information that indicates irregularities in the execution.
DebugN Logging of the program execution. "N" specifies the level of detail.
Procedure
1. Call "Settings" > "Logging..." in the menu bar.
The "Logging settings" window opens.
2. Activate the "Enable logging" checkbox.
This activates the creation of a log file. The log files can be created with the default settings
displayed in the dialog. If required, you can make fine settings for the logging.
3. A standard directory is specified for the log files.
If you want to use another directory as a log file directory, specify the desired directory, see
"Find directory/Create new directory" below.
Configuring ASC-SE/ASC-MO
5.6 Setting the log file
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 165
4. Activate the "Activate diagnostics logging" checkbox if you want an extended log file.
However, you can then no longer manually define the maximum file size and the log level.
5. Click "OK" to save the settings.
- OR -
Click "Cancel" to reject the settings.
Find directory / Create new directory
1. Click "..." behind "Directory:" if you want to set a different directory than that specified.
The "Find Directory" window opens.
2. Select the required directory in the directory tree.
- OR -
Click "Create new directory" to create a new directory.
3. Click "OK" to specify the directory.
Configuring ASC-SE/ASC-MO
5.6 Setting the log file
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
166 Installation Manual, 06/2017, A5E33520367B-AF
5.7 Activating functions
To use the remote access functions, activate the following functions via checkboxes in the
settings area "Remote access via Access MyMachine / settings":
● Screen enable
● File transfer
● STEP 7 via the Internet
● Automatic recording of the meeting
The "Screen enable" and "File transfer" functions are separate applications that exist between
the session leader and the machine operator.
Observing participants cannot participate actively in the actions.
Functions
Function Description
Screen enable Enables the screen enable for a remote access.
File transfer Enables the transfer of files.
STEP 7 via the Internet...
Seconds
Enables a remote access via STEP7.
Automatic recording of the
meeting
Enables the automatic recording of a conference.
Procedure
1. Open the "Administration" > "Organization administration" > "Organization data" tab.
2. The "Organization Data" window opens.
You can switch the individual functions on and off via the checkboxes at "Remote access
via Access MyMachine / settings".
3. Click "OK" to confirm the settings.
Configuring ASC-SE/ASC-MO
5.7 Activating functions
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 167
Configuring ASC-SE/ASC-MO
5.7 Activating functions
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
168 Installation Manual, 06/2017, A5E33520367B-AF
Appendix A
A.1 List of abbreviations
Admin Administrator (user role)
AMC Analyze MyCondition
AMD Access MyData
AMM/E Access MyMachine/Ethernet
AMP Analyze MyPerformance
AMT Access MyTool ID
ASC Access MyMachine/Ethernet Service Client
ASCII American Standard Code for Information Interchange
ASP Application Service Provider-Variante
BA Operating instructions
CAM Computer-Aided Manufacturing
CF card CompactFlash Card: Memory card
CNC Computerized Numerical Control:
CoL Certificate of License
COM Communication
COM Component Object Protocol (programming model of Microsoft®)
CU Control Unit
CP Communication Processor
CPU Central Processing Unit:
DB Data Block (PLC)
DBB Data Block Byte (PLC)
DBW Data Block Word (PLC)
DCOM Distributed Component Object Model
Dbxy Data Block (e.g. B 59)
DHCP Dynamic Host Configuration Protocol: Dynamic assignment of an IP address and other
configuration parameters on a computer in a network
DNC Direct Numeric Control
DIR Directory:
DW Data Word
FCC File Client Cache
ET Equability axis test
h Hour
HMI Human Machine Interface: SINUMERIK user interface
HD Hard Disk: Hard disk
HTTP Hypertext Transfer Protocol
HTTPS HyperText Transfer Protocol Secure,
HW Hardware
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 169
IAC InterActive Client
IB Commissioning engineer (user role)
IE Internet Explorer
IFC Interface Client
IH Maintenance
IIS Microsoft Internet Information Service
CT Circularity Test
MB Megabyte
MCIS Motion Control Information System
MCIS MDA MCIS Machine Data Aquisition: Machine data management
MCP Machine Control Panel:
MD Machine Data
MHComm Machine Handler Communication
MCS Machine Coordinate System
MLFB Machine-Readable Product Code
MMP Manage MyPrograms
MMP IFC Manage MyPrograms InterFace Client
MMT Manage MyTools
MO Machine Operator: Machine operator (user role)
MPI Multi Port Interface: Multiport Interface
MRL Manufacturing Resource Library
MS Microsoft
MSDE Microsoft Data Engine or Microsoft Desktop Engine database software
MSI Microsoft Software Installation
MSTT Machine control panel
NC Numerical Control: Numerical control
NCK Numerical Control Kernel: Numeric kernel with block preparation
NCU Numerical Control Unit: NCK hardware unit
NFS Network File System
NTLM NT LAN Manager: Authentication procedure for computer networks
OB Organization block in the PLC
ODBC Open Database Connectivity
OEM Original Equipment Manufacturer
OLE Object Linking & Embedding
OP Operation Panel: Operating equipment
OPI Operation Panel Interface: Interface for connection to the operator panel
OPC OLE for Process Control
PC Personal Computer
PCMCIA Personal Computer Memory Card International Association (memory card standardi‐
zation)
PCU PC Unit: Computer unit
PG Programming device
PDA Production Data Acquisition: Production data acquisition
PLC Programmable Logic Control: PLC
Appendix
A.1 List of abbreviations
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
170 Installation Manual, 06/2017, A5E33520367B-AF
PMT Parts Monitoring & Tracking: Parts tracking
PO POWER ON
ProToolPro Configuration tool
PWS Personal Web Server
RFC Requests for Comments
ROM Read Only Memory
SC Service Client
SE Service Engineer
SEC Service Engineer Client
SEG Tool presetter
SFI or SFI RM Shop Floor Integrate or Shop Floor Integrate Resource Management
SI SINUMERIK Integrate
SK Softkey
SSL Secure Socket Layer
SW Software
TDI Tool Data Information
TC Teamcenter
TCP Transmission Control Protocol
TLCA Tool Library CA: Tool catalog data
TLCU Tool Library Customer: Customer tool catalog data
TLCUA Tool Library Customer Assemblies: Complete tools
UAT Universal Axis Test
UNC Uniform naming convention
VB Visual Basic
VC Visual C
VNCK Virtual numerical control core
WCS Workpiece Coordinate System
T Tool
TLC Tool Length Compensation
WOP Workshop-Oriented Programming
WPD Work Piece Directory: Workpiece directory
TRC Tool Radius Compensation
WSDL Web Services Description Language
T Tool
TO Tool Offset
MT Machine Tool
TM Tool Management
TC Tool Change
XML Extensible Markup Language
Appendix
A.1 List of abbreviations
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 171
A.2 Documentation overview SINUMERIK 840D sl
7UDLQLQJGRFXPHQWDWLRQದ6LPSOHPLOOLQJZLWK6KRS0LOOದ6LPSOHWXUQLQJZLWK6KRS7XUQ7RRODQG0ROG0DNLQJ0DQXDO$GYHUWLVLQJEURFKXUH&DWDORJ1&&DWDORJ30)XQFWLRQ0DQXDO6DIHW\,QWHJUDWHG&RQILJXUDWLRQ0DQXDOದ(0&LQVWDOODWLRQJXLGHOLQHದ,QGXVWULDOVHFXULW\(TXLSPHQW0DQXDOದ1&8ದ2SHUDWRUFRPSRQHQWVDQGQHWZRUNLQJದ$',)XQFWLRQ0DQXDOದ%DVLFIXQFWLRQVದ([WHQGHG)XQFWLRQVದ6SHFLDO)XQFWLRQVದ6\QFKURQL]HG$FWLRQVದ,62'LDOHFWV)XQFWLRQ0DQXDO7RROPDQDJHPHQW2SHUDWLQJ0DQXDOದ8QLYHUVDOದ7XUQLQJದ0LOOLQJದ*ULQGLQJ&UHDWH0\&RQILJ2SHUDWLQJ0DQXDO3URJUDPPLQJ0DQXDOದ)XQGDPHQWDOVದ-RE3ODQQLQJದ0HDVXULQJ&\FOHV3URJUDPPLQJ0DQXDOದ,627XUQLQJದ,620LOOLQJ'LDJQRVWLFV0DQXDO$ODUPV&RPPLVVLRQLQJ0DQXDOದ&1&1&.3/&'ULYHದ%DVHVRIWZDUHDQGRSHUDWLQJVRIWZDUH/LVWV0DQXDOದ0DFKLQHGDWDದ,QWHUIDFHVLJQDOVದ9DULDEOHV6\VWHP0DQXDO*XLGHOLQHVIRUPDFKLQHFRQILJXUDWLRQ,QGXVWU\0DOO,QGXVWU\2QOLQH6XSSRUW6,26'2&RQ&'6\VWHP0DQXDO&WUO(QHUJ\(OHFWURQLFGRFXPHQWDWLRQ,QIR7UDLQLQJ*HQHUDOGRFXPHQWDWLRQ8VHUGRFXPHQWDWLRQ0DQXIDFWXUHU6HUYLFHGRFXPHQWDWLRQ0DQXIDFWXUHU6HUYLFHGRFXPHQWDWLRQ6,180(5,.6,180(5,.6,180(5,.6,180(5,.'VO'6,180(5,.'VO6,180(5,.'VO6,180(5,.'VO6,180(5,.'VO6,180(5,.'VO6,180(5,.'VO6,1$0,&666,180(5,.'VO6,1$0,&666,1$0,&666,180(5,.'VO'6,180(5,.'VO'6,180(5,.'VO6,1$0,&666,180(5,.'VO'6,180(5,.'VO6,180(5,.'VO'
Appendix
A.2 Documentation overview SINUMERIK 840D sl
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
172 Installation Manual, 06/2017, A5E33520367B-AF
Index
A
AMM/E Service Client
Installing with HMI-Advanced, 119
Uninstalling, 114
Uninstalling with HMI-Advanced, 134
Update, 111
AMM/E Service Client SE
configuring, 157
Installing on machine PC, 136
Online download, 149
Remote STEP 7, 154
Uninstalling, 155
App installation
Base Setup, 27
ASC-MO Update
HMI-Advanced, 117
SINUMERIK Operate, 112
Authentication procedures, 29
B
Base Setup, 26
Uninstalling, 34
Basic installation
Installer, 23
C
Certificate
Importing the root certificate, 60
Updating the RSA certificate, 59
Client installation
Overview, 16
Client setup
AMC directory, 13
AMM/E directory, 13
Configuring AMM/E remote access
Activating file transfer, 167
Activating screen enable, 167
Activating session recording, 167
Activating STEP 7, 167
File transfer, 159
Language selection, 164
Log file, 165
Login data, 158
Proxy server, 161
Set the language., 163
Configuring ASC-MO, 157
Configuring URLs
HMI Advanced, 67
SINUMERIK Operate, 33
Connection problems
HMI-Advanced, 57
D
Data transfer, 76
Download methods for the bootscript, 80
E
Expert mode, 65
G
Generic Driver Support, 72
I
IAC.exe, 85
Installer, 23
install, 23
Uninstalling, 35
Installing an AMC client
HMI-Advanced, 45
Industrial PC, 93
Overview, 19
Installing the TRANSLINE client setup, 84
L
Log file directory, 78
M
MhController, 86
MhCtrlr.exe, 86
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
Installation Manual, 06/2017, A5E33520367B-AF 173
P
Proxy
adapting, 28, 30
Authentication procedures, 29
Change configuration, 58
setting, 28
R
Registering the OPC server, 58
Remote STEP 7
AMM/E, 154
S
Setting data volumes, 74
SINUMERIK Integrate
Applications in ASP operation, 15
Display on SINUMERIK Operate softkey, 20
Enable at SINUMERIK Operate, 22
Start properties, 82
stopping at SINUMERIK Operate, 22
SINUMERIK Integrate client
Change,
Remove,
Repair,
Update for SINUMERIK Operate under Linux, 41
Update for SINUMERIK Operate under
Windows, 36
System requirement, 17
T
Teleservice update
HMI-Advanced, 115
Time synchronization, PLC-HMI, 84
U
Update
ASC-MO for HMI-Advanced, 117
ASC-MO for SINUMERIK Operate, 112
Teleservice for HMI-Advanced, 115
Index
Analyze MyCondition (AMC), Access MyMachine/Ethernet (AMM/E)
174 Installation Manual, 06/2017, A5E33520367B-AF
