2018 Microchip Technology Inc. DS20006029A-page 1
MIC94305
Features
• 1.8V to 3.6V Input Voltage Range
• Active Noise Rejection Over a Wide Frequency
Band
- >60 dB from 40 kHz to 5 MHz
• Rated to 500 mA Output Current
• Current-Limit and Thermal-Limit Protected
• 1.6 mm × 1.6 mm 6-Pin Thin DFN
• Logic-Controlled Enable Pin
• –40°C to +125°C Junction Temperature Range
Applications
• Smartphones
• Tablet PC/Notebooks and Webcams
• Digital Still and Video Cameras
• Video Conferencing
• Barcode Scanners
• Global Positioning Systems
• Automotive and Industrial Applications
General Description
The MIC94305 is an integrated load switch that
incorporates Microchip’s Ripple Blocker™ active filter
technology. The MIC94305 provides high-frequency
ripple attenuation (switching noise rejection) for
applications where switching noise cannot be tolerated
by sensitive downstream circuits, such as RF
applications. A low voltage logic enable pin
disconnects the pass element and puts the MIC94305
in a low current shutdown state when disabled.
The MIC94305 operates from an input voltage of 1.8V
to 3.6V, allowing true load switching of low voltage
power rails in any electronic device. The output voltage
(VOUT) is set at a fixed drop (typically 170 mV) from the
input voltage (VOUT = VIN – 170 mV). This maintains
high efficiency independent of given load conditions
and currents.
The MIC94305 is packaged in a 6-pin 1.6 mm x 1.6 mm
Thin DFN package and has a junction operating
temperature range of –40°C to +125°C.
Package Type
MIC94305
6-Pin TDFN (MT)
(Top View)
VOUT
VOUT
GND
VIN
VIN
EN
EP
1
2
34
5
6
500 mA Switch with Ripple Blocker™ Technology
MIC94305
DS20006029A-page 2 2018 Microchip Technology Inc.
Typical Application Circuit
Functional Block Diagram
MIC94305
1.6 x 1.6 TDFN
VIN
EN GND
VOUT
MIC94305YMT
C
IN
4.7μF
EN
C
OUT
4.7μF
LOAD
DC/DC
VIN
EN
DRIVER
CHARGE
PUMP
VOUT
BIAS AND
THERMAL
SHUTDOWN
GND
LPF
2018 Microchip Technology Inc. DS20006029A-page 3
MIC94305
1.0 ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings †
Input Voltage (VIN) .................................................................................................................................... –0.3V to +4.0V
Output Voltage (VOUT) .............................................................................................................................. –0.3V to +4.0V
Enable Voltage (VEN) ............................................................................................................ –0.3V to VIN+0.3V or +4.0V
ESD Rating (Note 1) ................................................................................................................................................ +3 kV
Operating Ratings ††
Input Voltage (VIN) .................................................................................................................................... +1.8V to +3.6V
Enable Voltage (VEN) ..........................................................................................................................................0V to VIN
† Notice: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the device at those or any other conditions above those indicated
in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended
periods may affect device reliability.
†† Notice: The device is not guaranteed to function outside its operating ratings.
Note 1: Devices are ESD sensitive. Handling precautions are recommended. Human body model, 1.5 kΩ in series
with 100 pF.
ELECTRICAL CHARACTERISTICS
Electrical Characteristics: VIN = VEN = 3.6V; IOUT = 1 mA; COUT = 4.7 µF; TA = +25°C, bold values indicate –40°C
≤ TJ ≤ +125°C, unless noted. Note 1
Parameter Sym. Min. Typ. Max. Units Conditions
Input Voltage VIN 1.8 —3.6 V—
Voltage Drop VDROP — 170 250 mV VIN – VOUT, –40°C ≤ TJ ≤ +85°C
VIN Ripple Rejection PSRR —45—dB f = 20 kHz, IOUT = 500 mA
— 55 — f = 100 kHz to 5 MHz, IOUT = 500 mA
Total Output Noise eN—98—µV
RMS f = 10 Hz to 100 kHz
Current Limit ILIM 530 725 1100 mA VOUT = 0V
Turn-On Time tON —90150 µs EN controlled
Load Regulation — — 10 — mV 100 µA to 100 mA
Ground Current IGND — 150 200 µA IOUT = 100 µA
Shutdown Current ISHDN —0.2 5 µAV
EN = 0V
Enable
Input Logic Low — — — 0.4 V—
Input Logic High — 1.0 —— V—
Input Current IIN —0.01 1 µA—
Note 1: Specification for packaged product only.
MIC94305
DS20006029A-page 4 2018 Microchip Technology Inc.
TEMPERATURE SPECIFICATIONS
Parameters Sym. Min. Typ. Max. Units Conditions
Temperature Ranges
Junction Operating Temperature TJ–40 — +125 °C —
Lead Temperature — — — +260 °C Soldering, 10 sec.
Storage Temperature Range TS–65 — +150 °C —
Package Thermal Resistances
Thermal Resistance, TDFN 6-Ld JA —92 —°C/W—
Note 1: The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable
junction temperature and the thermal resistance from junction to air (i.e., TA, TJ, JA). Exceeding the
maximum allowable power dissipation will cause the device operating junction temperature to exceed the
maximum +125°C rating. Sustained junction temperatures above +125°C can impact the device reliability.
2018 Microchip Technology Inc. DS20006029A-page 5
MIC94305
2.0 TYPICAL PERFORMANCE CURVES
FIGURE 2-1: PSRR COUT = 4.7 µF.
FIGURE 2-2: PSRR COUT = 4.7 µF.
FIGURE 2-3: PSRR COUT = 4.7 µF.
FIGURE 2-4: PSRR COUT = 10 µF.
FIGURE 2-5: PSRR COUT = 10 µF.
FIGURE 2-6: PSRR COUT = 10 µF.
Note: The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
MIC94305
DS20006029A-page 6 2018 Microchip Technology Inc.
FIGURE 2-7: PSRR COUT = 22 µF.
FIGURE 2-8: PSRR COUT = 22 µF.
FIGURE 2-9: PSRR COUT = 22 µF.
.
FIGURE 2-10: Output Voltage vs. Output
Current.
FIGURE 2-11: Output Voltage vs. Output
Current.
FIGURE 2-12: Voltage Drop vs. Output
Current.
2018 Microchip Technology Inc. DS20006029A-page 7
MIC94305
FIGURE 2-13: Voltage Drop vs. Input
Current.
FIGURE 2-14: Ground Current vs. Output
Current.
FIGURE 2-15: Ground Current vs. Input
Voltage.
FIGURE 2-16: Output Noise Spectral
Density.
FIGURE 2-17: Load Transient.
FIGURE 2-18: Line Transient.
Time (1.00ms/div)
VIN
(1V/div)
VOUT
(1V/div)
CIN = COUT = 4.7μF
IOUT = 300mA
MIC94305
DS20006029A-page 8 2018 Microchip Technology Inc.
FIGURE 2-19: Enable Turn -O ff.
FIGURE 2-20: Enable Turn -O n .
VEN
(1V/div)
VOUT
(2V/div)
Time (400μs/div)
VIN = 2.8V
CIN = COUT = 4.7μF
IOUT = 500mA
VEN
(1V/div)
VOUT
(2V/div)
Time (400μs/div)
VIN = 2.8V
CIN = COUT = 4.7μF
2018 Microchip Technology Inc. DS20006029A-page 9
MIC94305
3.0 PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1: PIN FUNCTION TABLE
Pin Number Pin Name Description
1, 2 VOUT Power switch output.
3 GND Ground.
4EN
Enable Input. A logic-high signal on this pin enables the part. Logic-low disables
the part. Do not leave floating.
5, 6 VIN Power switch input and chip supply.
ePad EP Exposed heatsink pad. Connect to Ground for best thermal performance.
MIC94305
DS20006029A-page 10 2018 Microchip Technology Inc.
4.0 APPLICATION INFORMATION
The MIC94305 uses Ripple Blocker technology to
integrate a load switch with a high-performance active
filter. The MIC94305 includes a low voltage logic
enable pin and is fully protected from damage caused
by fault conditions, offering linear current-limiting and
thermal shutdown.
4.1 Input Capacitor
The MIC94305 is a high-performance, high-bandwidth
device. An input capacitor of 0.47 µF is required from
the input to ground to provide stability. Low-ESR
ceramic capacitors provide optimal performance at a
minimum of space. Additional high-frequency
capacitors, such as small-valued NPO dielectric-type
capacitors, help filter out high-frequency noise and are
good practice in any RF-based circuit. X5R or X7R
dielectrics are recommended for the input capacitor.
Y5V dielectrics lose most of their capacitance over
temperature and are not recommended.
4.2 Output Capacitance
The MIC94305 requires an output capacitor of 4.7 µF
or greater to maintain stability. For optimal ripple
rejection performance, a 4.7 µF capacitor is
recommended. The design is optimized for use with
low-ESR ceramic-chip capacitors. High-ESR
capacitors are not recommended because they may
cause high-frequency oscillation. The output capacitor
can be increased, but performance has been optimized
for a 4.7 µF ceramic output capacitor and does not
improve significantly with larger capacitance.
X7R/X5R dielectric-type ceramic capacitors are
recommended because of their temperature
performance. X7R-type capacitors change capacitance
by 15% over their operating temperature range and are
the most stable type of ceramic capacitors. Z5U and
Y5V dielectric capacitors change value by as much as
50% and 60%, respectively, over their operating
temperature ranges. If you use a ceramic-chip
capacitor with a Y5V dielectric, the value must be much
higher than an X7R ceramic capacitor to ensure the
same minimum capacitance over the equivalent
operating temperature range.
4.3 No-Load Stability
The MIC94305 will remain stable with no load. This is
especially important in CMOS RAM keep-alive
applications.
4.4 Enable/Shutdown
The MIC94305 comes with an active-high enable pin
that allows the Ripple Blocker to be disabled. Forcing
the enable pin low disables the MIC94305 and sends it
into a “zero” off mode current state. In this state, current
consumed by the MIC94305 goes to nearly zero.
Forcing the enable pin high enables the output voltage.
The active-high enable pin uses CMOS technology and
cannot be left floating; a floating enable pin may cause
an indeterminate state on the output.
4.5 Thermal Considerations
The MIC94305 is designed to provide 500 mA of
continuous current in a very small package. Maximum
ambient operating temperature can be calculated
based on the output current and the voltage drop
across the part, which is fixed at 170 mV typical,
250 mV worst case. For example if the input voltage is
2.75V, the output voltage is 2.5V, and the output current
equals 500 mA. The actual power dissipation of the
Ripple Blocker™ can be determined using
Equation 4-1:
EQUATION 4-1:
Because this device is CMOS and the ground current
is typically <100 µA over the load range, the power
dissipation contributed by the ground current is <1%
and can be ignored for the calculation shown in
Equation 4-2.
EQUATION 4-2:
To determine the maximum ambient operating
temperature of the package, use the
junction-to-ambient thermal resistance of the device
and the Equation 4-3:
EQUATION 4-3:
Substituting PD for PD(MAX) and solving for the ambient
operating temperature will give the maximum operating
conditions for the regulator circuit.
For proper operation, the maximum power dissipation
must not be exceeded.
PDVIN VOUT
–IOUT VINIGND
+=
PD2.75V2.5V–500 mA=
PD0.125W=
PDMAX
TJMAX
TA
–
JA
--------------------------------
=
Where:
TJ(MAX) = +125°C; the max. junction temp. of the die.
θJA = 92°C/W for the 6-lead TDFN.
2018 Microchip Technology Inc. DS20006029A-page 11
MIC94305
For example, when operating the MIC94305YMT at a
2.75V input voltage and 500 mA load with a minimum
footprint layout, the maximum ambient operating
temperature TA can be determined as follows:
EQUATION 4-4:
It follows from this equation that the maximum ambient
operating temperature of 113.5°C is allowed in a
1.6 mm x 1.6 mm TDFN package. For a full discussion
of heat sinking and thermal effects on voltage
regulators, refer to the “Regulator Thermals” section of
Microchip’s Designing with Low-Dropout Voltage
Regulators handbook.
0.125W125CT
A
–92C/W=
TA113.5C=
MIC94305
DS20006029A-page 12 2018 Microchip Technology Inc.
5.0 PACKAGING INFORMATION
5.1 Package Marking Information
Example6-Lead TDFN*
XX 2W
Legend: XX...X Product code or customer-specific information
Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week code (week of January 1 is week ‘01’)
NNN Alphanumeric traceability code
Pb-free JEDEC® designator for Matte Tin (Sn)
*This package is Pb-free. The Pb-free JEDEC designator ( )
can be found on the outer packaging for this package.
●, ▲, ▼Pin one index is identified by a dot, delta up, or delta down (triangle
mark).
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information. Package may or may not include
the corporate logo.
Underbar (_) and/or Overbar (⎯) symbol may not be to scale.
3
e
3
e
2018 Microchip Technology Inc. DS20006029A-page 13
MIC94305
6-Lead 1.6 mm × 1.6 mm Thin DFN Package Outline & Recommended Land Pattern
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging.
MIC94305
DS20006029A-page 14 2018 Microchip Technology Inc.
NOTES:
2018 Microchip Technology Inc. DS20006029A-page 15
MIC94305
APPENDIX A: REVISION HIST OR Y
Revision A (May 2018)
• Converted Micrel document MIC94305 to Micro-
chip data sheet template DS20006029A.
• Minor grammatical text changes throughout.
• Added soldering conditions to Lead Temperature
value in Temperature Specifications.
• Added voltage drop information to Section 4.5
“Thermal Considerations”.
MIC94305
DS20006029A-page 16 2018 Microchip Technology Inc.
NOTES:
2018 Microchip Technology Inc. DS20006029A-page 17
MIC94305
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, contact your local Microchip representative or sales office.
Examples:
a) MIC94305YMT-T5: MIC94305, –40°C to +125°C
Temperature Range, 6-Lead
TDFN, 500/Reel
b) MIC94305YMT-TR: MIC94305, –40°C to +125°C
Temperature Range, 6-Lead
TDFN, 5,000/Reel
Device: MIC94305: 500 mA Switch with Ripple Blocker
Technology
Junction
Temperature
Range: Y = –40°C to +125°C, RoHS-Compliant
Package: MT = 6-Lead 1.6 mm x 1.6 mm TDFN
Media Type: T5 = 500/Reel
TR = 5,000/Reel
Note 1: Tape and Reel identifier only appears in the
catalog part number description. This identifier is
used for ordering purposes and is not printed on
the device package. Check with your Microchip
Sales Office for package availability with the
Tape and Reel option.
Device X XX -XX
Part No. Junction
Temp. Range
Package Media Type
MIC94305
DS20006029A-page 18 2018 Microchip Technology Inc.
NOTES:
2018 Microchip Technology Inc. DS20006029A-page 19
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights unless otherwise stated.
Trademarks
The Microchip name and logo, the Microchip logo, AnyRate, AVR,
AVR logo, AVR Freaks, BeaconThings, BitCloud, CryptoMemory,
CryptoRF, dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KEELOQ,
KEELOQ logo, Kleer, LANCheck, LINK MD, maXStylus,
maXTouch, MediaLB, megaAVR, MOST, MOST logo, MPLAB,
OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, Prochip
Designer, QTouch, RightTouch, SAM-BA, SpyNIC, SST, SST
Logo, SuperFlash, tinyAVR, UNI/O, and XMEGA are registered
trademarks of Microchip Technology Incorporated in the U.S.A.
and other countries.
ClockWorks, The Embedded Control Solutions Company,
EtherSynch, Hyper Speed Control, HyperLight Load, IntelliMOS,
mTouch, Precision Edge, and Quiet-Wire are registered
trademarks of Microchip Technology Incorporated in the U.S.A.
Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any
Capacitor, AnyIn, AnyOut, BodyCom, chipKIT, chipKIT logo,
CodeGuard, CryptoAuthentication, CryptoCompanion,
CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average
Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial
Programming, ICSP, Inter-Chip Connectivity, JitterBlocker,
KleerNet, KleerNet logo, Mindi, MiWi, motorBench, MPASM, MPF,
MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach,
Omniscient Code Generation, PICDEM, PICDEM.net, PICkit,
PICtail, PureSilicon, QMatrix, RightTouch logo, REAL ICE, Ripple
Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI,
SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC,
USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and
ZENA are trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated in
the U.S.A.
Silicon Storage Technology is a registered trademark of Microchip
Technology Inc. in other countries.
GestIC is a registered trademark of Microchip Technology
Germany II GmbH & Co. KG, a subsidiary of Microchip Technology
Inc., in other countries.
All other trademarks mentioned herein are property of their
respective companies.
© 2018, Microchip Technology Incorporated, All Rights Reserved.
ISBN: 978-1-5224-3068-1
Note the following deta ils of the code protection feature on Microchip devices:
• Microchip products meet the specification contained in their particular Microchip Data Sheet.
• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
• Microchip is willing to work with the customer who is concerned about the integrity of their code.
• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Microchip received ISO/TS-16949:2009 certif ication for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, micro perip hera ls, n onvolat ile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
QUALITYMANAGEMENTS
YSTEM
CERTIFIEDBYDNV
== ISO/TS16949==
DS20006029A-page 20 2018 Microchip Technology Inc.
AMERICAS
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Austin, TX
Tel: 512-257-3370
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Novi, MI
Tel: 248-848-4000
Houston, TX
Tel: 281-894-5983
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Tel: 317-536-2380
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Tel: 951-273-7800
Raleigh, NC
Tel: 919-844-7510
New York, NY
Tel: 631-435-6000
San Jose, CA
Tel: 408-735-9110
Tel: 408-436-4270
Canada - Toronto
Tel: 905-695-1980
Fax: 905-695-2078
ASIA/PACIFIC
Australia - Sydney
Tel: 61-2-9868-6733
China - Beijing
Tel: 86-10-8569-7000
China - Chengdu
Tel: 86-28-8665-5511
China - Chongqing
Tel: 86-23-8980-9588
China - Dongguan
Tel: 86-769-8702-9880
China - Guangzhou
Tel: 86-20-8755-8029
China - Hangzhou
Tel: 86-571-8792-8115
China - Hong Kong SAR
Tel: 852-2943-5100
China - Nanjing
Tel: 86-25-8473-2460
China - Qingdao
Tel: 86-532-8502-7355
China - Shanghai
Tel: 86-21-3326-8000
China - Shenyang
Tel: 86-24-2334-2829
China - Shenzhen
Tel: 86-755-8864-2200
China - Suzhou
Tel: 86-186-6233-1526
China - Wuhan
Tel: 86-27-5980-5300
China - Xian
Tel: 86-29-8833-7252
China - Xiamen
Tel: 86-592-2388138
China - Zhuhai
Tel: 86-756-3210040
ASIA/PACIFIC
India - Bangalore
Tel: 91-80-3090-4444
India - New Delhi
Tel: 91-11-4160-8631
India - Pune
Tel: 91-20-4121-0141
Japan - Osaka
Tel: 81-6-6152-7160
Japan - Tokyo
Tel: 81-3-6880- 3770
Korea - Daegu
Tel: 82-53-744-4301
Korea - Seoul
Tel: 82-2-554-7200
Malaysia - Kuala Lumpur
Tel: 60-3-7651-7906
Malaysia - Penang
Tel: 60-4-227-8870
Philippines - Manila
Tel: 63-2-634-9065
Singapore
Tel: 65-6334-8870
Taiwan - Hsin Chu
Tel: 886-3-577-8366
Taiwan - Kaohsiung
Tel: 886-7-213-7830
Taiwan - Taipei
Tel: 886-2-2508-8600
Thailand - Bangkok
Tel: 66-2-694-1351
Vietnam - Ho Chi Minh
Tel: 84-28-5448-2100
EUROPE
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
Finland - Espoo
Tel: 358-9-4520-820
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany - Garching
Tel: 49-8931-9700
Germany - Haan
Tel: 49-2129-3766400
Germany - Heilbronn
Tel: 49-7131-67-3636
Germany - Karlsruhe
Tel: 49-721-625370
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Germany - Rosenheim
Tel: 49-8031-354-560
Israel - Ra’anana
Tel: 972-9-744-7705
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Italy - Padova
Tel: 39-049-7625286
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Norway - Trondheim
Tel: 47-7289-7561
Poland - Warsaw
Tel: 48-22-3325737
Romania - Bucharest
Tel: 40-21-407-87-50
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
Sweden - Gothenberg
Tel: 46-31-704-60-40
Sweden - Stockholm
Tel: 46-8-5090-4654
UK - Wokingham
Tel: 44-118-921-5800
Fax: 44-118-921-5820
Worldwide Sales and Service
10/25/17
