FH30-80S-0.3SHW(05) - Hirose Electric

1

■Features

1.

Strong actuator retention

Actuator will not be dislodged when operating under harsh conditions.

2. Rotating Flip–Lock actuator

Rotating actuator permits easy insertion and retention of the FPC.

Tactile sensation confirms complete FPC insertion and reliable

mechanical and electrical connection.

3.

FPC position hold

Tabs on each side of the FPC assure correct placement and hold in

the connector prior to closing of the actuator.

4. Standard FPC/FFC thickness

Reliable connection with the use of the ready available 0.3 mm thick

FFC/FPC.

5. Easy solderability on the PC board

The soldering leads are on 0.6 mm or 0.8 mm pitch, exiting on the front

and back of the connector.

6. Board placement with automatic equipment

Flat surface and packaging on the tape-and-reel allows use of vacuum

nozzles.

Standard reel contains 1,000 pieces.

■Applications

Notebook computers, LCD, plasma display panels (PDP), HDD and

other devices requiring FPC connections using reliable and strong

multiple position connectors.

NEW

2008.3

0.3 or 0.4 mm pitch, 3 mm above the board, Flip-Lock actuator,

Flexible Printed Circuit ZIF connectors

FH30 Series

Strong actuator construction

Enclosed shaft of the actuator

prevents it from dislocation

Simple FPC insertion

Lock

FPC positioning tab

Hard

Disk-Drive

PCB PCB

PCB

Notebook computers, LCD

PDP

HDD

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors

2

■Product Specifications

Item Specification Conditions

100 V DC

0.3 mm pitch: 90 Vrms AC / 1 minute

0.4mm pitch: 150 Vrms AC / 1 minute

1 mA AC

20 cycles

Frequency: 10 to 55 Hz, single amplitude of 0.75 mm

10 cycles in each of the 3 directions

Acceleration of 981m/s2, 6 ms duration,

sine half-wave, 3 cycles in each of the 3 axis

96 hours at 40°C and humidity of 90 to 95%

Temperature: -40°C ➝+15°C to 35°C ➝+85°C ➝+15°C to 35°C

Time: -30 ➝maximum 5 ➝+30 ➝+maximum 5 minutes

5 cycles

Reflow: At the recommended temperature profile

Manual soldering: 350°C for 5 seconds

1. Insulation resistance 500 Mø min.

2. Withstanding voltage No flashover or insulation breakdown

3. Contact resistance 150 mø max.

* Including FPC conductor resistance

4. Durability Contact resistance: 150 mø max.

No damage, cracks, or parts dislocation

5. Vibration

No electrical discontinuity of 1µs or longer

Contact resistance: 150 mø max.

No damage, cracks, or parts dislocation

6. Shock

No electrical discontinuity of 1µs or longer

Contact resistance: 150 mø max.

No damage, cracks, or parts dislocation

7.

Humidity (Steady state)

Contact resistance: 150 mø max.

Insulation resistance: 50Mø min.

No damage, cracks, or parts dislocation

8. Temperature cycle

Contact resistance: 150 mø max.

Insulation resistance: 50Mø min.

No damage, cracks, or parts dislocation

9.

Resistance to soldering heat

No deformation of components affecting

performance.

Note1: When passing the current through all of the contacts, use 70% of the rated current.

Note2: Includes temperature rise caused by current flow.

Note3: The term "storage" refers to products stored for a long period prior to mounting and use.

The operating temperature and humidity range covers the non-conducting condition of connectors after installation on a board.

■Materials

Insulator LCP Color: Gray/beige UL94V-0

Actuator LCP Color: Black UL94V-0

Contacts Phosphor bronze Gold flash --------------

Part Material Finish Remarks

Recommended FPC Thickness: 0.3±0.05, Gold plated contact pads

Ratings

Current rating(Note 1)

Voltage rating

0.3 mm pitch

0.15 A

30 Vrms AC

0.4 mm pitch

0.3 A

50 Vrms AC

Operating temperature range -40 to +85°C (Note 2)

Operating humidity range Relative humidity 90% max.

(No condensation)

Storage temperature range -10 to +50°C (Note 3)

Storage humidity range Relative humidity 90% max.

(No condensation)

■Ordering information

qSeries name : FH30

wBlank : 0.3mm pitch

M : 0.4 mm pitch

eNumber of contacts : 80

rContact pitch : 0.3 mm, 0.4 mm

tContact type : SHW(SMT horizontal staggered mounting)

yPlating specifications(05): Gold flash plated (RoHS compliant)

FH 30 M - 80S - 0.3 SHW (05)

1 2 3 4 5 6

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

3

FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors

■Dimensions

4.2

Vacuum pick-up surface

0.8 0.8

6.55

Number of contacts indicator

B

R9

R

C

Q

A

D

(E: FPC insertion slot dimension)

(0.12)

3

4.85

**

Notes 1: The coplanarity of each terminal lead is within 0.1.

2: Slight variations in color of the plastic compounds do not affect form ,fit or function of the connector.

Tape and reel packaging (1,000 pieces/reel).

Order by number of reels.

Part Number

FH30-80S-0.3SHW(05)

FH30M-80S-0.4SHW(05)

580-0100-4-05

580-0102-0-05

80

0.3

0.4

CL No.

Number of Contacts

FPC contact pitch

All dimensions: mm

YES

RoHS

A B C D E Q R

27.9

35.8

23.7

31.6

23.4

31.2

23.4

31.2

24.35

32.25

0.3

0.4

0.6

0.8

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

BRecommended PCB mounting pattern and metal mask dimensions

0.25±0.03(Metal mask)

1.7±0.1 3.95±0.1

1.7±0.1

R±0.05

R±0.05 0.3±0.03(Land)

Mark side

0.25±0.03(Metal mask)

C±0.05Q±0.05

B±0.05

D±0.05

0.3±0.03(Land)

BRecommended FPC Dimensions

J±0.1

0.3±0.05

2.2±0.1

A

R0.2

Q±0.02

R±0.02

B±0.03

F±0.05

G±0.1

0.3±0.07

0.3 +0.04

-0.03

0.3±0.07

2.65±0.2 (0.5)

3.2±0.3

0.07±0.070.1±0.05

0.3 +0.04

-0.03

1.3±0.1(0.8)

No.1

No.2

No(n-1)

No (n)

4.2±0.3

1.4±0.1

(C0.5)

H MIN

0.05 MIN

0±0.1

2

Detail A

Recommended metal mask thickness: t=0.15

Note 1 : Polyimide and thermally hardening adhesive is recommended as the materials for the stiffener.

2 : Conductor width shall be 0.1±0.05 if FPC has plating bars.

Part Number

FH30-80S-0.3SHW(05)

FH30M-80S-0.4SHW(05)

580-0100-4-05

580-0102-0-05

80

CL No.

Number of Contacts

0.3

0.4

FPC contact pitch

23.7

31.6

23.4

31.2

23.4

31.2

24.3

32.2

24.8

32.7

25.3

33.2

26.3

34.2

0.3

0.4

0.6

0.8

B C D F G H J Q R

All dimensions: mm

4

FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

5

FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors

●Embossed Carrier Tape Dimensions

BPackaging Specifications

Unreeling direction

1.35±0.1

(4.9)

(N)

(6.8)

12±0.1

2±0.15

4±0.1

Ø1.5

+0.1

0

1.75±0.1M±0.1

L±0.1

K±0.3

1.7 +0.15

0

1.5+0.1

0

0.4±0.1

●Reel Dimensions

(Ø13)

(T: INSIDE)

(U: OUTSIDE)

(Ø80)

(Ø380)

End section Mounting section Lead section (400mm min.)

Embossed carrier tape

Top cover tape

No connector inserted

(10 pockets min.)

No connector inserted

(10 pockets min.)

Tape and reel packaging (1,000 pieces/reel).

Part Number

FH30-80S-0.3SHW(05)

FH30M-80S-0.4SHW(05)

CL No.

580-0100-4-05

580-0102-0-05

Number of Contacts

80

K

44

56

L

40.4

52.4

M

20.2

26.2

N

28.1

36

T

45.4

57.4

U

49.4

61.4

All dimensions: mm

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

6

FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors

MAX 250ç

Start

Temperature(ç)

Time (Seconds)

25ç (60 sec.)

(30 sec.)

90 to 120 sec.

Preheating

Soldering

0

50

100

150 150ç

200ç

230ç

200

250

HRS test condition

Solder method :Reflow, IR/hot air

(Nihon Den-netsu Co., Ltd.'s Part Number:SENSBY NR-2)

Environment :Room air

Solder composition :Paste, 96.5%Sn/3.0%Ag/0.5%Cu

(Senju Metal Industry, Co., Ltd.'s Part Number:M705-221CM5-42-10.5)

Test board :Glass epoxy 45mm∞80mm∞1.6mm thick

Land dimensions :0.3mm∞1.7mm

Metal mask :0.25∞1.7∞0.15mm thick

The temperature profiles shown are based on the above conditions.

In individual applications the actual temperature may vary,depending on

solder paste type, volume / thickness and board size / thickness.

Consult your solder paste and equipment manufacturer for specific

recommendations.

BTemperature Profile

●Using Lead-free Solder Paste

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

7

FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors

B

FH30 Series Recommended FPC Construction

1. Using Single-sided FPC FPC : Flexible Printed Circuit

Material Name

Copper foil

Base adhesive

Base film

Reinforcement material adhesive

Stiffener

Material

Material Thickness

(µm)

Cu 1oz

Polyimide 1 mil thick

Thermosetting adhesive

Polyimide 7 mil thick

Covering film layer

Cover adhesive

Polyimide 1 mil thick

35

25

30

175

25

Surface treatment

Connecting side

Back side

0.2µm thick gold plated over 1 to 5µm

thick nickel underplating

3

Total 293

2. Using Double-sided FPC

* To prevent release of the FPC due to it’s bending, use of the double-sided FPC with copper foil on the back side is NOT

RECOMMENDED.

FPC : Flexible Printed Circuit

Material Name

Covering layer film

Cover adhesive

Material

Material Thickness

(µm)

Connecting side

Back side

Polyimide 1 mil thick

Through-hole copper

Copper foil

Base adhesive

Base film

Base adhesive

Cu

Cu 1/2oz

Polyimide 1 mil thick

15

18

25

18

Surface treatment

0.2µm thick gold plated over 1 to 5µm

thick nickel underplating

3

Copper foil

Cover adhesive

Covering film layer

Reinforcement material adhesive

Stiffener

Cu 1/2oz

Polyimide 1 mil thick

Thermosetting adhesive

Polyimide 1 mil thick

18

25

50

100

Total 297

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

8

FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors

BOperation and Precautions

Operation and Precautions

qInstall on the PC board with the actuator open.

wFPC Insertion

Orient the FPC with the contact pads facing down.

Insert in the connector at an angle, assuring that the

positioning tabs are placed in the corresponding

positioning tab areas on both sides of the insulator body.

Lower the FPC to a position parallel to the mounting

surface.

Verify the correct position by slightly pulling horizontally

on the FPC.

Positioning tab area (each side)

eActuator closing after the FPC is fully inserted.

Rotate the actuator down to a full stop, pushing it at the

center.

rRemoving the FPC

Carefully rotate the actuator up, lifting it at the center.

Lift the FPC slightly to clear the positioning tabs and

withdraw it from the connector.

Positioning part

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

9

FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors

BPrecautions

Operation and Precautions

Rotation shaft

qActuator operation

The actuator rotates at the center of it’s shaft, as

illustrated in the figure below.

Be careful not to apply excessive force when operating

the actuator from the open position (before the FPC has

been inserted).

Exercise care not to touch the contacts with fingernails or

any other object.

wFPC Insertion and closing of the actuator.

Do not insert the FPC on an angle as illustrated in the

photograph below.

eMake sure that the FPC/FFC does not rub against

the insertion slot or the contacts, as illustrated on the

figure below.

Properly insert the FPC positioning tabs into the

corresponding areas on both sides of the insulator body.

Incorrect FPC insertion

Correct FPC insertion

During the closing of the actuator do not pull up or push

on it directly down.

Do not grasp the actuator and pull on it (photograph

below).

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

10

FH30 Series●0.3 or 0.4mm pitch, 3mm above the board, Flip-Lock actuator, Flexible Printed Circuit ZIF connectors

Operation and Precautions

Closing of the actuator.

Rotate down pushing it at the center or evenly at each

end, as shown on the photographs below. Do not push at

one end only.

rOpening of the actuator

Rotate up, lifting it at the center or evenly at each end of

the actuator.

Do not lift at one end only.

tForces to the FPC/FFC after insertion and closing of

the actuator.

Do not apply upward pull-force to the FPC/FFC close to

the connector.

If a need arise to route the FPC/FFC upward, assure that

it is NOT transferring any forces to the closed actuator.

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.