Data Sheet Rev. 2.6
www.infineon.com/voltage-regulators 1 2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Features
• Output voltage tolerance ≤±2%
• 400 mA output current capability
• Low-drop voltage
• Very low standby current consumption
• Input voltage up to 40 V
• Overvoltage protection up to 60 V (≤400 ms)
• Reset function down to 1 V output voltage
• ESD protection up to 2000 V
• Adjustable reset time
•On/off logic
• Overtemperature protection
• Reverse polarity protection
• Short-circuit proof
• Wide temperature range
•Suitable for use in automotive electronics
• Green Product (RoHS compliant)
Potential applications
• Automotive applications directly connected to the battery
• Applications with a protected power supply for off-board load
Product validation
Qualified for automotive applications. Product validation according to AEC-Q100/101.
Description
TLE4267 is a 5 V low drop voltage regulator for automotive applications in the PG-TO263-7 or PG-DSO-14
package. It supplies an output current of greater than 400 mA. The IC is short-circuit-proof and has an
overtemperature protection circuit.
Data Sheet 2 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Type Package Marking
TLE4267G PG-TO263-7 TLE4267
TLE4267GM PG-DSO-14 TLE4267
Data Sheet 3 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Potential applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Product validation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Pin assignment PG-TO263-7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Pin assignment PG-DSO-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3 General product characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2 Functional range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.3 Thermal resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4 Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4.1 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2 Typical performance characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5 Test and application circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6 Package outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table of contents
Data Sheet 4 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Block diagram
1 Block diagram
Figure 1 Block diagram TLE4267
BLOCKDIAGRAM
Temperature
Sensor
Saturation
Control and
Protection Circuit
Adjustment Bandgap
Reference
Turn-ON/Turn-OFF
Logic
Reset
Generator
Input I
E6E2
RO
D
Q
Inhibit Hold
Reset
Output
Reset
Delay
5V
Output
Control
Amplifier Buffer
Ground
GND
Data Sheet 5 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Pin configuration
2 Pin configuration
2.1 Pin assignment PG-TO263-7
Figure 2 Pin configuration (top view)
Table 1 Pin definitions and functions
Pin Symbol Function
1IInput; block to ground directly at the IC by a ceramic capacitor
2E2Inhibit; device is turned on by High signal on this pin; internal pull-down
resistor of 100 kΩ
3ROReset Output; open-collector output internally connected to the output via a
resistor of 30 kΩ
4GNDGround; connected to rear of chip
5DReset Delay; connect via capacitor to GND
6E6Hold; see Table 6 for function; this input is connected to output voltage via a
pull-up resistor of 50 kΩ
7Q5V Output; block to GND with 22 μF capacitor, ESR < 3 Ω
7651234
AEP01724
E6 Q
D
GND
RO
E2
Ι
Data Sheet 6 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Pin configuration
2.2 Pin assignment PG-DSO-14
Figure 3 Pin configuration (top view)
Table 2 Pin definitions and functions
Pin Symbol Function
1IInput; block to ground directly at the IC by a ceramic capacitor
2E2Inhibit; device is turned on by High signal on this pin; internal pull-down
resistor of 100 kΩ
7ROReset Output; open-collector output internally connected to the output via a
resistor of 30 kΩ
3, 4, 5, 10, 11,
12
GND Ground; connected to rear of chip
8DReset Delay; connect with capacitor to GND for setting delay
9E6Hold; see Table 6 for function; this input is connected to output voltage via a
pull-up resistor of 50 kΩ
13 Q 5V Output; block to GND with 22 μF capacitor, ESR ≤3Ω
6, 14 N.C. Not Connected
AEP02710
E6
GND
N.C.
N.C.
RO
GND
Q
10
9
GND GND
1
2
3
4
5
GND
6
7D
14
13
12
11
E2
GND
8
Ι
Data Sheet 7 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
General product characteristics
3 General product characteristics
3.1 Absolute maximum ratings
Notes
1. Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
2. Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
data sheet. Fault conditions are considered as outside normal operating range. Protection functions are not
designed for continuous repetitive operation.
Table 3 Absolute maximum ratings1)
TJ = -40 to 150°C
1) Not subject to production test, specified by design.
Parameter Symbol Values Unit Note or Test Condition Number
Min. Typ. Max.
Input
Voltage VI-42 – 42 V – P_3.1.1
Voltage VI––60Vt≤400 ms P_3.1.2
Current II– – – – Internally limited P_3.1.3
Reset output
Voltage VRO -0.3 – 7 V – P_3.1.4
Current IRO – – – – Internally limited P_3.1.5
Reset delay
Voltage VD-0.3 – 42 V – P_3.1.6
Current ID––– –– P_3.1.7
Output
Voltage VQ-0.3 – 7 V – P_3.1.8
Current IQ– – – – Internally limited P_3.1.9
Inhibit
Voltage VE2 -42 – 42 V – P_3.1.10
Current IE2 -5 – 5 mA t≤400 ms P_3.1.11
Hold
Voltage VE6 -0.3 – 7 V – P_3.1.12
Current IE6 – – – mA Internally limited P_3.1.13
GND
Current IGND -0.5 – – A – P_3.1.14
Temperatures
Junction temperature TJ– – 150 °C – P_3.1.15
Storage temperature Tstg -50 – 150 °C – P_3.1.16
Data Sheet 8 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
General product characteristics
3.2 Functional range
Note: Within the functional or operating range, the IC operates as described in the circuit description. The
electrical characteristics are specified within the conditions given in the Electrical Characteristics
table.
3.3 Thermal resistance
Note: This thermal data was generated in accordance with JEDEC JESD51 standards. For more
information, go to www.jedec.org.
Table 4 Functional range
Parameter Symbol Values Unit Note or Test Condition Number
Min. Typ. Max.
Input voltage VI5.5 – 40 V – P_3.2.1
Junction temperature TJ-40 – 150 °C – P_3.2.2
Table 5 Thermal resistance
Parameter Symbol Values Unit Note or Test Condition Number
Min. Typ. Max.
PG-TO263-7 package
Junction ambient Rthja ––70K/W– P_3.3.4
Junction-case Rthjc ––6 K/W– P_3.3.5
Junction-case Zthjc ––2 K/Wt<1ms P_3.3.6
PG-DSO-14 package
Junction ambient Rthja ––70K/W– P_3.3.10
Junction-pin Rthjp ––30K/W– P_3.3.11
Data Sheet 9 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Functional description
4 Functional description
Application
The IC regulates an input voltage VI in the range of 5.5 V < VI< 40 V to a nominal output voltage of VQ=5.0V.
A reset signal is generated for an output voltage of VQ<VRT (typ. 4.5 V). The reset delay can be set with an
external capacitor. The device has two logic inputs. A voltage of VE2 > 4.0 V applied to the E2-pin (e.g. by
ignition) turns the device on. Depending on the voltage on pin E6 the IC may be kept in Hold active-state even
if VE2 goes to low level (see Table 6). This makes it simple to implement a self-holding circuit without external
components. When the device is turned off, the output voltage drops to 0 V and current consumption tends
towards 0 μA.
Design notes for external components
The input capacitor CI is necessary for compensation of line influences. The resonant circuit consisting of lead
inductance and input capacitance can be damped by a resistor of approximately 1 Ω in series with CI. The
output capacitor is necessary for the stability of the regulating circuit. Stability is specified at values of
CQ≥22 μF and an ESR of ≤3Ω within the operating temperature range.
Circuit description
The control amplifier compares a reference voltage, which is kept highly accurate by resistance adjustment,
to a voltage that is proportional to the output voltage and drives the base of the series transistor via a buffer.
Saturation control as a function of the load current prevents any over-saturating of the power element.
The reset output RO is in high-state if the voltage on the delay capacitor CD is greater or equal VUD. The delay
capacitance CD is charged with the current ID for output voltages greater than the reset threshold VRT. If the
output voltage drops below VRT a fast discharge of the delay capacitor CD sets in and as soon as VCD drops below
VLD the reset output RO is set to low-level (see Figure 6). The reset delay can be set within a wide range by
dimensioning the capacitance of the external capacitor.
Table 6 Truth table for turn-ON/turn-OFF logic
E2,
Inhibit1)
1) Inhibit: E2 Enable function, active high.
E6,
Hold2)
2) Hold: E6 Hold and release function, active low.
VQRemarks
LXOFFInitial state
H X ON Regulator switched on via Inhibit, by ignition for example
H L ON Hold clamped active to ground by controller while Inhibit is still high
X L ON Previous state remains, even if ignition is shutting off: self-holding state
L L ON Ignition shut off while regulator is in self-holding state
L H OFF Regulator shut down by releasing of Hold while Inhibit remains Low, final state.
No active clamping required by external self-holding circuit (μC) to keep
regulator in off-state
Data Sheet 10 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Functional description
4.1 Electrical characteristics
Table 7 Electrical characteristics
VI = 13.5 V; -40°C < TJ < 125°C; VE2 > 4 V (unless specified otherwise)
Parameter Symbol Values Unit Note or Test Condition Number
Min. Typ. Max.
Output voltage VQ4.9 5 5.1 V 5 mA ≤IQ≤400 mA
6V≤VI≤26 V
P_4.1.1
Output voltage VQ4.9 5 5.1 V 5 mA ≤IQ ≤150 mA
6V≤VI ≤40 V
P_4.1.2
Output current limiting IQ500 – – mA TJ= 25°C P_4.1.3
Current consumption
Iq = II - IQ
Iq––50μAIC turned off P_4.1.4
Current consumption
Iq = II - IQ
Iq–1.010μATJ= 25°C
IC turned off
P_4.1.5
Current consumption
Iq = II - IQ
Iq–1.34 mAIQ=5mA
IC turned on
P_4.1.6
Current consumption
Iq = II - IQ
Iq––60mAIQ= 400 mA P_4.1.7
Current consumption
Iq = II - IQ
Iq––80mAIQ= 400 mA
VI=5V
P_4.1.8
Drop voltage VDr –0.30.6VIQ= 400 mA1) P_4.1.9
Load regulation ∆VQ––50mV5mA≤IQ≤400 mA P_4.1.10
Supply-voltage regulation ∆VQ–1525mVVI=6to36V;
IQ=5mA
P_4.1.11
Supply-voltage rejection SVR –54– dBfr= 100 Hz;
Vr=0.5Vpp
P_4.1.12
Longterm stability ∆VQ– 0 – mV 1000 h P_4.1.13
Reset generator
Switching threshold VRT 4.2 4.5 4.8 V – P_4.1.14
Reset High level – 4.5 – – V Rext =∞P_4.1.15
Saturation voltage VRO,SAT –0.10.4VRR=4.7kΩ2) P_4.1.16
Internal Pull-up resistor RRO –30– kΩ–P_4.1.17
Saturation voltage VD,SAT – 50 100 mV VQ<VRT P_4.1.18
Charge current ID81525μAVD=1.5 V P_4.1.19
Upper delay switching threshold VUD 2.6 3 3.3 V – P_4.1.20
Delay time tD–20– msCD= 100 nF P_4.1.21
Lower delay switching threshold VLD –0.43– V– P_4.1.22
Reset reaction time tRR –2– μsCD=100nF P_4.1.23
Inhibit
Turn on voltage VU,INH –34 VIC turned on P_4.1.24
Turn off voltage VL,INH 2–– VIC turned off P_4.1.25
Data Sheet 11 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Functional description
Pull-down resistor RINH 50 100 200 kΩ–P_4.1.26
Hysteresis ∆VINH 0.2 0.5 0.8 V – P_4.1.27
Input current IINH – 35 100 μAVINH =4V P_4.1.28
Hold voltage VU,HOLD 30 35 40 % Referred to VQP_4.1.29
Turn off voltage VL,HOLD 60 70 80 % Referred to VQP_4.1.30
Pull-up resistor RHOLD 20 50 100 kΩ–P_4.1.31
Overvoltage Protection
Turn off voltage VI,OV 42 44 46 V VI increasing P_4.1.32
Turn on voltage VI,turn on 36 – – V VI decreasing
after turn off
P_4.1.33
1) Drop voltage = VI - VQ (measured when the output voltage VQ has dropped 100 mV from the nominal value obtained at
VI =13.5V).
2) The reset output is low for 1 V < VQ<VRT.
Table 7 Electrical characteristics (cont’d)
VI = 13.5 V; -40°C < TJ < 125°C; VE2 > 4 V (unless specified otherwise)
Parameter Symbol Values Unit Note or Test Condition Number
Min. Typ. Max.
Data Sheet 12 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Functional description
4.2 Typical performance characteristics
Output voltage VQ versus
junction temperature Tj
Drop voltage VDr versus
output current IQ
Charge current ID versus
junction temperature Tj
Delay switching threshold VUD versus
junction temperature Tj
AED01486
-40
4.70
Q
T
V
Ι
=
5.10
V
4.80
4.90
5.00
13.5 V
C
0 40 80 160
V
j
AED01488
0
0
Ι
Q
C
T
125 C
=25
=
T
100
200
300
400
500
mV
700
100 200 300 400 mA 600
Dr
V
j
j
AED01485
-40
Ι
D
T
V
Ι
= 13.5 V
C
0 40 80 160
A
V
C
=0 V
μ
10
12
14
16
18
22
D
Ι
j
AED01487
-40
0
UD
T
VΙ= 13.5 V
C
0 40 80 160
0.5
1.0
1.5
2.0
2.5
3.0
V
4.0
VUD
V
j
Data Sheet 13 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Functional description
Current consumption Iq versus
output current IQ
Current consumption Iq versus
input voltage VI
Output current limiting IQ versus
junction temperature Tj
Output current limiting IQ versus
input voltage VI
AED01491
0
0
q
Ι
=
10 20 30 50
R
L
Ι
V
V
Ω25
5
10
mA
15
AED01489
-40
Ι
Q
T
C
0 40 80 160
mA
100
200
300
400
500
700
0
13.5 V=
Ι
V
j
00
AED01987
Ι
Q
V
V
i
mA
100
200
300
400
500
600
700
10 20 30 40 50
125 C=
=C25
j
T
j
T
Data Sheet 14 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Functional description
Output voltage VQ versus
inhibit voltage VINH
Inhibit current IINH versus
inhibit voltage VINH
00
AED01988
V
Q
2
4
V
6
1
3
5
INH
V
1 2 3456
V
00
AED01989
Ι
INH
V
V
INH
1 2 3456
10
20
30
40
50
Aμ
Data Sheet 15 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Test and application circuit
5 Test and application circuit
Figure 4 Test circuit TLE4267
Figure 5 Application circuit TLE4267
AES01483
22 F
Ι
Q
Ι
RO
V
E6
Ω4.7 k
D
RO
QΙ
E2
Ι
1000 F 470 nF
Ι
Ι
V
E2 D
C
V
C
GND
Ι
d
Ι
V
R
Q
V
V
Ι
TLE 4267
μμ
Inhibit
GND Hold
APPLICATIONDIAGRAM
TLE4267
+
I
Input Q
E2
E6GND
RO
D
Inhibit; e.g.
from Terminal 15
Reset
to µC
5V
Output
Hold
from µC
22µF100nF
e.g.
470nF
Data Sheet 16 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Test and application circuit
Figure 6 Time response
AET01985
t
D
t
RR
RR
t<
Power
Reset Shutdown
Thermal Voltage Drop
at Input Undervoltage
at Output Secondary
Spike Bounce
Load Shutdownon
V
RO, SAT
LD
V
UD
V
V
D, SAT
RT
V
L, INH
V
V
U, INH
INH
V
RO
V
V
D
Q
V
Ι
V
t
t
t
t
t
=
dt
Vd
D
D
C
Ι
Data Sheet 17 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Test and application circuit
Figure 7 Enable and Hold behavior
AET01986
V
Enable inactive, clamped by int.
V
pull-down resistor
GND by external
Hold active, clamped to
Power-ON reset
5)
4)
3)
Cμ
V
Hold inactive, pulled up by
Enable active
V
RO, SAT
2)
1)
RO
3)
t
D
LD
V
V
D, SAT
UD
V
V
RT
D
E6
E6
V
Voltage controller shutdown
10)
9)
8)
μ
was released to
No switch on via
Output-low reset
than 4 s Vfor more
possible after E6
E6, rel
V>
Hold inactive, released by
Pulse width smaller than
7)
6)
Q
t
C
s
μ
1μ
9)
RR
8)
E6
V
V
Q, NOM
V
Q
U, HOLD
V
L, HOLD
V2)
1)
μ
4) 6)
<1 s
5)
μ
7) 10)
10<s
V
Ι
E2
V
U, INH
L, INH
V
V
t
t
t
t
t
t
Data Sheet 18 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Package outlines
6 Package outlines
Green Product (RoHS compliant)
To meet the world-wide customer requirements for environmentally friendly products and to be compliant
with government regulations the device is available as a green product. Green products are RoHS-Compliant
(i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020).
Figure 8 PG-TO263-7 (Plastic Transistor Single Outline)
Figure 9 PG-DSO-14 (Plastic Dual Small Outline)
For further information on alternative packages, please visit our website:
http://www.infineon.com/packages.Dimensions in mm
A
BA0.25
M
0.1
Typical
±0.2
10
8.5
1)
7.55
1)
(15)
±0.2
9.25
±0.3
1
0...0.15
7 x 0.6
±0.1
±0.1
GPT09114
1.27
4.4
B
0.5
±0.1
±0.3
2.7
4.7
±0.5
0.05
1)
0.1
Metal surface min. X = 7.25, Y = 6.9
2.4
1.27
All metal surfaces tin plated, except area of cut.
0...0.3
B
6 x
8˚ MAX.
Data Sheet 19 Rev. 2.6
2018-07-03
TLE4267
5 V Low Drop Voltage Regulator
Revision history
7 Revision history
Revision Date Changes
2.6 2018-07-03 Discontinued product variants TLE4267 and TLE4267S removed from data sheet.
Editorial changes.
Package updated by optional chamfer for PG-DSO-14.
2.51 2012-02-20 Page 1: Cover page added.
Page 4: Figure 1 “Block diagram TLE4267” updated with clear label for reset
output pin.
Page 15: Figure 5 “Application circuit TLE4267” updated with clear labels for
inhibit, hold, reset and reset delay pin.
2.5 2007-03-20 Initial version of RoHS-compliant derivative of TLE4267:
Page 1: AEC certified statement added.
Page 1 and Page 18 ff: RoHS compliance statement and Green product feature
added.
Page 1 and Page 18 ff: Package changed to RoHS compliant version
Legal Disclaimer updated.
Trademarks
All referenced product or service names and trademarks are the property of their respective owners.
Edition 2018-07-03
Published by
Infineon Technologies AG
81726 Munich, Germany
© 2018 Infineon Technologies AG.
All Rights Reserved.
Do you have a question about any
aspect of this document?
Email: erratum@infineon.com
Document reference
Z8F50686678
IMPORTANT NOTICE
The information given in this document shall in no
event be regarded as a guarantee of conditions or
characteristics ("Beschaffenheitsgarantie").
With respect to any examples, hints or any typical
values stated herein and/or any information regarding
the application of the product, Infineon Technologies
hereby disclaims any and all warranties and liabilities
of any kind, including without limitation warranties of
non-infringement of intellectual property rights of any
third party.
In addition, any information given in this document is
subject to customer's compliance with its obligations
stated in this document and any applicable legal
requirements, norms and standards concerning
customer's products and any use of the product of
Infineon Technologies in customer's applications.
The data contained in this document is exclusively
intended for technically trained staff. It is the
responsibility of customer's technical departments to
evaluate the suitability of the product for the intended
application and the completeness of the product
information given in this document with respect to
such application.
For further information on technology, delivery terms
and conditions and prices, please contact the nearest
Infineon Technologies Office (www.infineon.com).
WARNINGS
Due to technical requirements products may contain
dangerous substances. For information on the types
in question please contact your nearest Infineon
Technologies office.
Except as otherwise explicitly approved by Infineon
Technologies in a written document signed by
authorized representatives of Infineon Technologies,
Infineon Technologies’ products may not be used in
any applications where a failure of the product or any
consequences of the use thereof can reasonably be
expected to result in personal injury.