IDPC-45 45W Constant Current Mode LED Driver (for DA-Type only) Features Constant Current mode output Flicker free design PCB type design Built-in active PFC function No load power consumption<0.5W(Blank-Type), series SELV Applications LED panel lighting LED flood lighting Indoor LED lighting Standby power consumption<0.5W(DA-Type) Function options: 2 in 1 dimming (dim-to-off); Auxiliary DC output; DALI 3 years warranty Description IDPC-45 series is a 45W PCB type LED AC/DC driver featuring the constant current mode output with flicker free design. IDPC-45 operates from 90~295VAC and offers models with different rated current ranging between 350mA and 1400mA. Thanks to the efficiency up to 86%, with the fanless design, the entire series is able to operate for -20~+40 ambient temperature under free air convection. IDPC-45 is equipped with various function options, such as dimming methodologies, so as to provide the optimal design flexibility for lighting system. Model Encoding IDPC - 45 A - 350 Function options Rated output current(350/500/700/1050/1400mA) A:Auxiliary DC output(12V@50mA) :None Output wattage Series name { Type Blank DA Function 2 in 1 dimming (0~10VDC and 10V PWM) DALI control technology Note In Stock In Stock Note: The DALI control model(DA Type) only for IDPC-45 Non Auxiliary DC output models. File Name:IDPC-45-SPEC 2017-09-14 IDPC-45 45W Constant Current Mode LED Driver series SPECIFICATION IDPC-45 -350 IDPC-45 -500 IDPC-45 -700 IDPC-45 -1050 IDPC-45 -1400 RATED CURRENT 350mA 500mA 700mA 1050mA 1400mA RATED POWER 33.25W 45W 44.8W 45.15W 44.8W CONSTANT CURRENT REGION Note.2 57 ~ 95V 54 ~ 90V 38 ~ 64V 26 ~ 43V 19 ~ 32V OPEN CIRCUIT VOLTAGE(max.) 118V 115V 84V 63V 50V 84% 83% MODEL OUTPUT CURRENT RIPPLE 5% max. @rated current CURRENT TOLERANCE 7.0% SETUP TIME 500ms / 230VAC 1200ms/115VAC Note.4 AUXILIARY DC OUTPUT Note.5 Nominal 12V(deviation 11.4~12.6)@50mA for IDPC-45A only VOLTAGE RANGE Note.3 FREQUENCY RANGE INPUT 90 ~ 295VAC 127 ~ 417VDC (Please refer to "STATIC CHARACTERISTIC" section) 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.95/115VAC, PF>0.92/230VAC, PF>0.9/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section) TOTAL HARMONIC DISTORTION THD< 20%(@load60%/115VAC,230VAC; @load75%/277VAC) (Please refer to "TOTAL HARMONIC DISTORTION" section) EFFICIENCY (Typ.) 86% AC CURRENT 0.6A/115VAC 0.4A/230VAC INRUSH CURRENT (Typ.) COLD START 30A(twidth=100s measured at 50% Ipeak) at 230VAC; Per NEMA 410 85% 85% 0.3A/277VAC MAX. No. of PSUs on 16A 32 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC CIRCUIT BREAKER LEAKAGE CURRENT <0.75mA / 277VAC NO LOAD/STANDBY POWER CONSUMPTION No load power consumption<0.5W for Blank-Type,<1.2W for IDPC-45A Standby power consumption<0.5W for DA-Type Hiccup mode,auto-recovery after fault condition is removed for DA type Hiccup mode,re-power on to recovery for other type PROTECTION SHORT CIRCUIT WORKING TEMP. Ta=-20 ~ +40 (Please refer to " OUTPUT LOAD vs TEMPERATURE" section) WORKING HUMIDITY 20 ~ 90% RH non-condensing ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80, 10 ~ 95% RH TEMP. COEFFICIENT 0.03%/ (0 ~ 40) VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes SAFETY STANDARDS UL8750, CSA C22.2 NO.250.13-12; ENEC EN61347-1, EN61347-2-13, EN62384,GB19510.1,GB19510.14 approved DALI STANDARDS WITHSTAND VOLTAGE Compliance to IEC62386-101, 102 for DA-Type only I/P-O/P:3.75KVAC SAFETY & ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25/ 70% RH EMC Compliance to EN55015, EN61000-3-2 Class C (@load60%) ; EN61000-3-3,GB17743,GB17625.1 EMC EMISSION EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level( surge immunity:Line-Line:1KV ) MTBF 408.8Khrs min. OTHERS DIMENSION PACKING NOTE MIL-HDBK-217F (25) 120*66.5*25mm(L*W*H) 0.14Kg; 81pcs/ 12.5Kg/ 1.32CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature. 2. Please refer to "DRIVING METHODS OF LED MODULE". 3. De-rating may be needed under low input voltages. Please refer to STATIC CHARACTERISTIC sections for details. 4. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time. 5. There is no design of short circuit protection for the Auxiliary DC output; this function can not be used when dimming input terminals(DIM+,DIM-) are short circuit or when it is no load or short circuit at output(Vo+,Vo-). 6. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. 7.The DALI version driver does not support the bit 1: Lamp failure in the Command 144 Query status of the DALI standard. File Name:IDPC-45-SPEC 2017-09-14 IDPC-45 45W Constant Current Mode LED Driver series Block Diagram fosc : 70KHz AUX+(for IDPC-45A) AUX- (for IDPC-45A) RECTIFIERS I/P EMI FILTER & RECTIFIERS RECTIFIERS & FILTER POWER SWITCHING O.L.P. PWM&PFC CONTROL CURRENT LIMIT Vo+ VoDIM+(DA+) DIM-(DA-) DETECTION CIRCUIT DRIVING METHODS OF LED MODULE This series works in constant current mode to directly drive the LEDs. In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. 100 Vo(%) Constant Current area Should there be any compatibility issues, please contact MEAN WELL. 60 (min.) Hiccup Protection 50 100 Io(%) Typical output current normalized by rated current (%) File Name:IDPC-45-SPEC 2017-09-14 IDPC-45 45W Constant Current Mode LED Driver series TB1 ACL ACL ACN ACN - DIMMING OPERATION FS1 + HS1 DIM-(DA-) TB2 HS2 Vo+ Vo- A K A DIM+(DA+) O G I 2 in 1 dimming function Output constant current level can be adjusted by applying one of the two methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Applying additive 0 ~ 10VDC 100% 90% Vo- + + - - DIM+ + Output current (%) 80% Vo+ 70% 60% 50% 40% 30% Additive Voltage - 20% DIM- 10% "DO NOT connect "DIM- to Vo- " 0% 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage Applying additive 10V PWM signal (frequency range 300Hz ~ 3KHz): 100% 90% Vo- + + - - DIM+ Additive PWM signal Output current (%) 80% Vo+ 70% 60% 50% 40% 30% 20% DIM"DO NOT connect "DIM- to Vo- " DALI Interface (primary side; for DA-Type) Apply DALI signal between DA+ and DA-. DALI protocol comprises 16 groups and 64 addresses. First step is fixed at 8% of output. 10% 0% 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< I out<8%. 2. The output current could drop down to 0% when dimming input is about 0Vdc or 10V PWM signal with 0% duty cycle. File Name:IDPC-45-SPEC 2017-09-14 IDPC-45 45W Single Output LED Power Supply series OUTPUT LOAD vs TEMPERATURE 90~295VAC for 350mA Model,200~295VAC for others 100 80 90~200VAC for models other than 350mA Model LOAD (%) 60 40 20 -20 -10 0 10 20 30 (HORIZONTAL) 40 AMBIENT TEMPERATURE,Ta () STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC 100 1 for 350mA Model 90 0.95 80 PF LOAD (%) 0.9 for others 70 60 50 115V 0.85 230V 277V 0.8 40 0.75 90 135 180 295 200 0.7 50% INPUT VOLTAGE (V) 60% 80% 90% 100% (45W) LOAD De-rating is needed under low input voltage. TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs LOAD IDPC-45 series possess superior working efficiency that up to 86% can be reached in field applications. 350mA Model 350mA Model 90 14 88 10 277V 8 230V 6 115V 4 2 EFFICIENCY(%) 16 12 THD(%) 70% 86 84 277V 82 230V 115V 80 78 0 50% 60% 70% LOAD 80% 90% 100% 76 50% 60% 70% 80% 90% 100% LOAD File Name:IDPC-45-SPEC 2017-09-14 IDPC-45 45W Constant Current Mode LED Driver series MECHANICAL SPECIFICATION Unit:mm 120 112 1 4 * - 4 FS1 2 3. 5 3 M 4 M + TB1 3 A K A 2 HS2 58.5 66.5 HS1 1 4 5 6 TB2 25 O G I IDPC-45 Terminal Pin No. Assignment(TB2) Terminal Pin No. Assignment(TB1) Pin No. 1 2 3 4 Pin No. 1 2 Assignment ACL ACL ACN ACN Assignment DIM+(DA+) DIM-(DA-) Pin No. 3 4 Assignment Vo+ Vo- IDPC-45A Terminal Pin No. Assignment(TB2) Pin No. 1 2 3 Assignment DIM+ DIMVo+ Pin No. 4 5 6 Assignment VoAUX+ AUX- Installation Manual Please refer to : http://www.meanwell.com/manual.html File Name:IDPC-45-SPEC 2017-09-14