IDPC-45-500 - MEAN WELL ENTERPRISES

■Model Encoding

■Description

■Features ■Applications

LED panel lighting

LED flood lighting

Indoor LED lighting

Rated output current(350/500/700/1050/1400mA)

Output wattage

Series name

-350

IDPC -45

File Name:IDPC-45-SPEC 2017-09-14

IDPC-45 series is a 45W PCB type LED AC/DC driver featuring the constant current mode output

with flicker free design. IDPC-45 operates from 90~295VAC and offers models with different rated

current ranging between 350mA and 1400mA. Thanks to the efficiency up to 86%, with the fanless

design, the entire series is able to operate for -20 ~+40 ambient temperature under free air convection. ℃℃

IDPC-45 is equipped with various function options, such as dimming methodologies, so as to provide

the optimal design flexibility for lighting system.

SELV

Function options

45W Constant Current Mode LED Driver IDPC-45 series

Constant Current mode output

Flicker free design

PCB type design

Built-in active PFC function

No load power consumption<0.5W(Blank-Type),

Standby power consumption<0.5W(DA-Type)

Function options: 2 in 1 dimming (dim-to-off);

Auxiliary DC output; DALI

3 years warranty

Type

Blank

Function Note

In Stock

2 in 1 dimming (0~10VDC and 10V PWM)

DA DALI control technology

(for DA-Type only)

Note: The DALI control model(DA Type) only for IDPC-45 Non Auxiliary DC output models.

A:Auxiliary DC output(12V@50mA)

:None

{

SPECIFICATION

File Name:IDPC-45-SPEC 2017-09-14

MODEL

OUTPUT

SETUP TIME Note.4

FREQUENCY RANGE

POWER FACTOR (Typ.)

EFFICIENCY (Typ.)

AC CURRENT

INPUT

INRUSH CURRENT (Typ.)

LEAKAGE CURRENT

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

MTBF

DIMENSION

OTHERS

NOTE

PACKING

SHORT CIRCUIT

<0.75mA / 277VAC

20 ~ 90% RH non-condensing

-40 ~ +80 , 10 ~ 95% RH℃

±℃ ℃0.03%/ (0 ~ 40 )

10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes

408.8Khrs min. MIL-HDBK-217F (25 )℃

0.14Kg; 81pcs/ 12.5Kg/ 1.32CUFT

ENVIRONMENT

SAFETY &

EMC

PROTECTION

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

I/P-O/P:3.75KVAC

I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH℃

SAFETY STANDARDS

Compliance to EN55015, EN61000-3-2 Class C ( ) ; EN61000-3-3,GB17743,GB17625.1@load 60%≧

EMC IMMUNITY

EMC EMISSION

120*66.5*25mm(L*W*H)

Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level( )surge immunity:Line-Line:1KV

UL8750, CSA C22.2 NO.250.13-12; ENEC EN61347-1, EN61347-2-13, EN62384,GB19510.1,GB19510.14 approved

TOTAL HARMONIC DISTORTION

VOLTAGE RANGE Note.3

IDPC-45 -350 IDPC-45 -700 IDPC-45 -1400

350mA 700mA 1400mA

33.25W 44.8W 44.8W

118V

500ms / 230VAC 1200ms/115VAC

47 ~ 63Hz

PF>0.95/115VAC, PF>0.92/230VAC, PF>0.9/277VAC@full load

(Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)

86% 85% 83%

0.6A/115VAC 0.4A/230VAC 0.3A/277VAC

COLD START 30A(twidth= s measured at 50% Ipeak) at 230VAC100μ;Per NEMA 410

57 ~ 95V 38 ~ 64V 19 ~ 32V

84V 50V

IDPC-45 -500

500mA

45W

85%

54 ~ 90V

115V

IDPC-45 -1050

1050mA

45.15W

84%

26 ~ 43V

63V

RATED CURRENT

RATED POWER

CURRENT TOLERANCE

CONSTANT CURRENT REGION

Note.2

OPEN CIRCUIT VOLTAGE

(max.)

CURRENT RIPPLE

±7.0%

5% max. @rated current

THD< 20%(@load 60%/115VAC,230VAC; @load 75%/277VAC)≧≧

(Please refer to “TOTAL HARMONIC DISTORTION” section)

MAX. No. of PSUs on 16A

CIRCUIT BREAKER 32 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC

(Please refer to "STATIC CHARACTERISTIC" section)

90 ~ 295VAC 127 ~ 417VDC

AUXILIARY DC OUTPUT

Note.5

Nominal 12V(deviation 11.4~12.6)@50mA for IDPC-45A only

45W Constant Current Mode LED Driver IDPC-45 series

1. All parameters NOT specially mentioned are measured at 230VAC input, rated current and 25 of ambient temperature.℃

2. Please refer to "DRIVING METHODS OF LED MODULE".

3. De rating may be needed under low input voltages. Please .- refer to STATIC CHARACTERISTIC sections for details

4. Length of set up time is measured at cold first start. Turning ON/OFF the driver may lead to increase of the set up time.

5. There is no design of short circuit protection for the Auxiliary DC output; this function can not be used when dimming input terminals(DIM+,DIM-)

are short circuit or when it is no load or short circuit at output(Vo+,Vo-).

6. The driver is considered as a component that will be operated in combination with final equipment. Since EMC performance will be

affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

7.The DALI version driver does not support the bit 1: Lamp failure in the Command 144 Query status of the DALI standard.

NO LOAD/STANDBY

POWER CONSUMPTION

WORKING TEMP.

Ta=-20 ~ +40 (Please refer to “ OUTPUT LOAD vs TEMPERATURE” section)℃

No load power consumption<0.5W for Blank-Type,<1.2W for IDPC-45A

Standby power consumption<0.5W for DA-Type

DALI STANDARDS Compliance to IEC62386-101, 102 for DA-Type only

Hiccup mode,auto-recovery after fault condition is removed for DAtype；

Hiccup mode,re-power on to recovery for other type

File Name:IDPC-45-SPEC 2017-09-14

fosc : 70KHz

Block Diagram

DRIVING METHODS OF LED MODULE

※This series works in constant current mode to directly drive the LEDs.

Typical output current normalized by rated current (%)

In the constant current region, the highest voltage at the output of the driver

depends on the configuration of the end systems.

Should there be any compatibility issues, please contact MEAN WELL.

100

(min.)

Vo(%)

50 100 Io(%)

Constant

Current area

Hiccup

Protection

45W Constant Current Mode LED Driver IDPC-45 series

DIM+(DA+)

DIM-(DA-)

DETECTION

CIRCUIT

EMI FILTER

RECTIFIERS

POWER

SWITCHING

FILTER

RECTIFIERS

Vo+

Vo-

I/P

CONTROL

CURRENT

LIMIT

PWM&PFC

O.L.P.

AUX+(for IDPC-45A)

AUX- (for IDPC-45A)

DIMMING OPERATION

※2 in 1 dimming function

Output constant current level can be adjusted by applying one of the two methodologies between DIM+ and DIM-:

0 ~ 10VDC, or 10V PWM signal.

Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers.

◎Applying additive 0 ~ 10VDC

◎Applying additive 10V PWM signal (frequency range 300Hz ~ 3KHz):

Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< out<8%.I

2. The output current could drop down to 0% when dimming input is about 0Vdc or 10V PWM signal with 0% duty cycle.

Vo+

Vo-

DIM+

DIM-

“DO NOT connect "DIM- ”to Vo-

Additive Voltage

Vo+

Vo-

DIM+

DIM-

“DO NOT connect "DIM- ”to Vo-

Additive PWM signal

0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V

10%

20%

30%

40%

50%

60%

70%

80%

90%

100%

Output current (%)

10% 20% 30% 40% 50% 60% 70% 80% 90% 100%

10%

20%

30%

40%

50%

60%

70%

80%

90%

100%

Output current (%)

Dimming input: Additive voltage

Duty cycle of additive 10V PWM signal dimming input

File Name:IDPC-45-SPEC 2017-09-14

45W Constant Current Mode LED Driver IDPC-45 series

ACN

ACL

HS1

FS1

TB1

AKA

HS2

ACN

ACL

Vo+

DIM+(DA+)

TB2

Vo-

DIM-(DA-)

※DALI Interface (primary side; for DA-Type)

Apply DALI signal between DA+ and DA-.

DALI protocol comprises 16 groups and 64 addresses.

First step is fixed at 8% of output.

0.7

0.75

0.8

0.85

0.9

0.95

50% 60% 70% 80% 90% 100%

115V

230V

277V

File Name:IDPC-45-SPEC 2017-09-14

45W Single Output LED Power Supply IDPC-45 series

OUTPUT LOAD vs TEMPERATURE

50% 60% 70% 80% 90% 100%

277V

230V

115V

50% 60% 70% 80% 90% 100%

277V

230V

115V

LOAD

STATIC CHARACTERISTIC

TOTAL HARMONIC DISTORTION (THD)

POWER FACTOR (PF) CHARACTERISTIC

※De-rating is needed under low input voltage.

EFFICIENCY vs LOAD

IDPC-45 series possess superior working efficiency that up to 86% can

be reached in field applications.

※350mA Model ※350mA Model

EFFICIENCY(%)

THD(%)

LOAD

(45W)

INPUT VOLTAGE (V)

LOAD (%)

90 295

100

135 180

for others

for 350mA Model

200

LOAD

LOAD (%)

(HORIZONTAL)

-20 -10 0 10 20 30 40

100

90~295VAC for 350mA Model,200~295VAC for others

90~200VAC for models other

than 350mA Model

AMBIENT TEMPERATURE,Ta ( )℃

File Name:IDPC-45-SPEC 2017-09-14

Unit:mm

MECHANICAL SPECIFICATION

45W Constant Current Mode LED Driver IDPC-45 series

IDPC-45

Terminal Pin No. Assignment(TB2)※

Pin No. Pin No.

Assignment Assignment

DIM+(DA+)

Vo-DIM-(DA-)

Vo+

※Terminal Pin No. Assignment(TB1)

Pin No.

Assignment

ACL

ACN

Installation Manual

Please refer to : http://www.meanwell.com/manual.html

TB2

HS2

HS1

FS1

TB1

AKA

120

66.5

112

58.5

435*ψ .

IDPC-45A

※Terminal Pin No. Assignment(TB2)

Pin No. Pin No.

Assignment Assignment

DIM+ Vo-

DIM-

Vo+

AUX+

AUX-