CAT24C32YI-GT3JN - ON Semiconductor

May, 2018 − Rev. 26

1Publication Order Number:

CAT24C32/D

CAT24C32

EEPROM Serial 32-Kb I2C

Description

The CAT24C32 is a EEPROM Serial 32−Kb I2C devices, internally

organized as 4096 words of 8 bits each.

It features a 32−byte page write buffer and supports the Standard

(100 kHz), Fast (400 kHz) and Fast−Plus (1 MHz) I2C protocol.

External address pins make it possible to address up to eight

CAT24C32 devices on the same bus.

Features

•Supports Standard, Fast and Fast−Plus I2C Protocol

•1.7 V to 5.5 V Supply Voltage Range

•32−Byte Page Write Buffer

•Hardware Write Protection for Entire Memory

•Schmitt Triggers and Noise Suppression Filters on I2C Bus Inputs

(SCL and SDA)

•Low Power CMOS Technology

•1,000,000 Program/Erase Cycles

•100 Year Data Retention

•Industrial and Extended Temperature Range

•PDIP, SOIC, TSSOP, UDFN, US 8−lead, WLCSP 4−ball and 5−ball

Packages

•This Device is Pb−Free, Halogen Free/BFR Free, and RoHS

Compliant

www.onsemi.com

See detailed ordering and shipping information in the package

dimensions section on page 9 of this data sheet.

ORDERING INFORMATION

SOIC−8

W SUFFIX

CASE 751BD

TSSOP−8

Y SUFFIX

CASE 948AL

For the location of Pin 1, please consult the

corresponding package drawing.

UDFN8

HU4 SUFFIX

CASE 517AZ

WLCSP4

C4C SUFFIX

CASE 567JY

* In Development; please contact factory for availability

WLCSP5

C5A SUFFIX

CASE 567JQ

VCC

SDA

VSS

SCL

WLCSP4 (C4C)

WLCSP5 (C5A)

WP SCL

VCC VSS

SDA

132

PIN CONFIGURATIONS (Top Views)

SDA

VCC

VSS

SCL

PDIP (L), SOIC (W), TSSOP (Y),

US (US), UDFN (HU4)

SOIC−8 WIDE

X SUFFIX

CASE 751BE

CAT24C32

www.onsemi.com

DEVICE MARKINGS

(SOIC−8)

(TSSOP−8)

(UDFN−8)

C5U = Specific Device Code

A = Assembly Location

XX = Last Two Digits of Assembly Lot Number

Y = Production Year (Last Digit)

M = Production Month (1−9, O, N, D)

C5U

AXX

C32F

AYMXXX

C32F = Specific Device Code

A = Assembly Location

Y = Production Year (Last Digit)

M = Production Month (1−9, O, N, D)

XXX = Last Three Digits of Assembly Lot Number

24C32F = Specific Device Code

A = Assembly Location

Y = Production Year (Last Digit)

M = Production Month (1−9, O, N, D)

XXX = Last Three Digits of Assembly Lot Number

24C32F

AYMXXX

2 = Specific Device Code

Y = Production Year (Last Digit)

M = Production Month (1−9, O, N, D)

(WLCSP−5)

B = Specific Device Code

Y = Production Year (Last Digit)

M = Production Month (1−9, O, N, D)

(WLCSP−4)

Figure 1. Functional Symbol

SDA

SCL

CAT24C32

VCC

VSS

A2, A1, A0

Device AddressA0, A1, A2

Serial DataSDA

Serial ClockSCL

Write ProtectWP

Power SupplyVCC

GroundVSS

FunctionPin Name

PIN FUNCTION

CAT24C32

www.onsemi.com

Table 1. ABSOLUTE MAXIMUM RATINGS

Parameters Ratings Units

Storage Temperature –65 to +150 °C

Voltage on any Pin with Respect to Ground (Note 1) –0.5 to +6.5 V

Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality

should not be assumed, damage may occur and reliability may be affected.

1. The DC input voltage on any pin should not be lower than −0.5 V or higher than VCC + 0.5 V. During transitions, the voltage on any pin may

undershoot to no less than −1.5 V or overshoot to no more than VCC + 1.5 V, for periods of less than 20 ns.

Table 2. RELIABILITY CHARACTERISTICS (Note 2)

Symbol Parameter Min Units

NEND (Note 3) Endurance 1,000,000 Program/Erase Cycles

TDR Data Retention 100 Years

2. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC−Q100

and JEDEC test methods.

3. Page Mode, VCC = 5 V, 25°C.

Table 3. D.C. OPERATING CHARACTERISTICS

(VCC = 1.8 V to 5.5 V, TA = −40°C to +125°C and VCC = 1.7 V to 5.5 V, TA = −40°C to +85°C, unless otherwise speciﬁed.)

Symbol Parameter Test Conditions Min Max Units

ICCR Read Current Read, fSCL = 400 kHz 1 mA

ICCW Write Current Write, fSCL = 400 kHz 2 mA

ISB Standby Current All I/O Pins at GND or VCC TA = −40°C to +85°C

VCC ≤ 3.3 V

1mA

TA = −40°C to +85°C

VCC > 3.3 V

TA = −40°C to +125°C 5

ILI/O Pin Leakage Pin at GND or VCC 2mA

VIL Input Low Voltage −0.5 VCC x 0.3 V

VIH Input High Voltage SCL, SDA Inputs VCC x 0.7 6.5 V

WP, A0, A1, A2 Inputs VCC x 0.7 VCC + 0.5

VOL1 Output Low Voltage VCC ≥ 2.5 V, IOL = 3.0 mA 0.4 V

VOL2 Output Low Voltage VCC < 2.5 V, IOL = 1.0 mA 0.2 V

Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product

performance may not be indicated by the Electrical Characteristics if operated under different conditions.

Table 4. PIN IMPEDANCE CHARACTERISTICS

(VCC = 1.8 V to 5.5 V, TA = −40°C to +125°C and VCC = 1.7 V to 5.5 V, TA = −40°C to +85°C, unless otherwise speciﬁed.)

Symbol Parameter Conditions Max Units

CIN (Note 4) SDA I/O Pin Capacitance VIN = 0 V, TA = 25°C, f = 1.0 MHz 8 pF

CIN (Note 4) Input Capacitance (other pins) VIN = 0 V, TA = 25°C, f = 1.0 MHz 6 pF

IWP (Note 5) WP Input Current VIN < VIH, VCC = 5.5 V 130 mA

VIN < VIH, VCC = 3.3 V 120

VIN < VIH, VCC = 1.7 V 80

VIN > VIH 2

IA (Note 5) Address Input Current

(A0, A1, A2)

Product Rev F

VIN < VIH, VCC = 5.5 V 50 mA

VIN < VIH, VCC = 3.3 V 35

VIN < VIH, VCC = 1.7 V 25

VIN > VIH 2

4. These parameters are tested initially and after a design or process change that affects the parameter according to appropriate AEC−Q100

and JEDEC test methods.

5. When not driven, the WP, A0, A1 and A2 pins are pulled down to GND internally. For improved noise immunity, the internal pull−down is relatively

strong; therefore the external driver must be able to supply the pull−down current when attempting to drive the input HIGH. To conserve power,

as the input level exceeds the trip point of the CMOS input buffer (~ 0.5 x VCC), the strong pull−down reverts to a weak current source.

CAT24C32

www.onsemi.com

Table 5. A.C. CHARACTERISTICS

(VCC = 1.8 V to 5.5 V, TA = −40°C to +125°C and VCC = 1.7 V to 5.5 V, TA = −40°C to +85°C.) (Note 6)

Symbol Parameter

Standard

VCC = 1.7 V − 5.5 V

Fast

VCC = 1.7 V − 5.5 V

Fast−Plus (Note 9)

VCC = 2.5 V − 5.5 V

TA = −405C to +855C

Units

Min Max Min Max Min Max

FSCL Clock Frequency 100 400 1,000 kHz

tHD:STA START Condition Hold Time 4 0.6 0.25 ms

tLOW Low Period of SCL Clock 4.7 1.3 0.45 ms

tHIGH High Period of SCL Clock 4 0.6 0.40 ms

tSU:STA START Condition Setup Time 4.7 0.6 0.25 ms

tHD:DAT Data In Hold Time 0 0 0 ms

tSU:DAT Data In Setup Time 250 100 50 ns

tR (Note 7) SDA and SCL Rise Time 1,000 300 100 ns

tF (Note 7) SDA and SCL Fall Time 300 300 100 ns

tSU:STO STOP Condition Setup Time 4 0.6 0.25 ms

tBUF Bus Free Time Between STOP

and START

4.7 1.3 0.5 ms

tAA SCL Low to Data Out Valid 3.5 0.9 0.40 ms

tDH (Note 7) Data Out Hold Time 100 100 50 ns

Ti (Note 7) Noise Pulse Filtered at SCL and

SDA Inputs

100 100 100 ns

tSU:WP WP Setup Time 0 0 0 ms

tHD:WP WP Hold Time 2.5 2.5 1 ms

tWR Write Cycle Time 5 5 5 ms

tPU (Notes 7, 8) Power−up to Ready Mode 1 1 1 ms

6. Test conditions according to “A.C. Test Conditions” table.

7. Tested initially and after a design or process change that affects this parameter.

8. tPU is the delay between the time VCC is stable and the device is ready to accept commands.

9. Fast−Plus (1 MHz) speed class available for product revision “F”. The die revision “F” is identified by letter “F” or a dedicated marking code

on top of the package.

Table 6. A.C. TEST CONDITIONS

Input Drive Levels 0.2 x VCC to 0.8 x VCC

Input Rise and Fall Time ≤ 50 ns

Input Reference Levels 0.3 x VCC, 0.7 x VCC

Output Reference Level 0.5 x VCC

Output Test Load Current Source IOL = 3 mA (VCC ≥ 2.5 V); IOL = 1 mA (VCC < 2.5 V); CL = 100 pF

CAT24C32

www.onsemi.com

Power−On Reset (POR)

Each CAT24C32 incorporates Power−On Reset (POR)

circuitry which protects the internal logic against powering

up in the wrong state. The device will power up into Standby

mode after VCC exceeds the POR trigger level and will

power down into Reset mode when VCC drops below the

POR trigger level. This bi−directional POR behavior

protects the device against ‘brown−out’ failure following a

temporary loss of power.

Pin Description

SCL: The Serial Clock input pin accepts the clock signal

generated by the Master.

SDA: The Serial Data I/O pin accepts input data and delivers

output data. In transmit mode, this pin is open drain. Data is

acquired on the positive edge, and is delivered on the

negative edge of SCL.

A0, A1 and A2: The Address inputs set the device address

that must be matched by the corresponding Slave address

bits. The Address inputs are hard−wired HIGH or LOW

allowing for up to eight devices to be used (cascaded) on the

same bus. When left floating, these pins are pulled LOW

internally. The Address inputs are not available for use with

WLCSP 4−ball and 5−ball.

WP: When pulled HIGH, the Write Protect input pin

inhibits all write operations. When left floating, this pin is

pulled LOW internally. The WP input is not available for the

WLCSP 4−ball, therefore all write operations are allowed

for the device in this package.

Functional Description

The CAT24C32 supports the Inter−Integrated Circuit

(I2C) Bus protocol. The protocol relies on the use of a Master

device, which provides the clock and directs bus traffic, and

Slave devices which execute requests. The CAT24C32

operates as a Slave device. Both Master and Slave can transmit

or receive, but only the Master can assign those roles.

I2C Bus Protocol

The 2−wire I2C bus consists of two lines, SCL and SDA,

connected to the VCC supply via pull−up resistors. The

Master provides the clock to the SCL line, and either the

Master or the Slaves drive the SDA line. A ‘0’ is transmitted

by pulling a line LOW and a ‘1’ by letting it stay HIGH. Data

transfer may be initiated only when the bus is not busy (see

A.C. Characteristics). During data transfer, SDA must

remain stable while SCL is HIGH.

START/STOP Condition

An SDA transition while SCL is HIGH creates a START

or STOP condition (Figure 2). The START consists of a

HIGH to LOW SDA transition, while SCL is HIGH. Absent

the START, a Slave will not respond to the Master. The

STOP completes all commands, and consists of a LOW to

HIGH SDA transition, while SCL is HIGH.

Device Addressing

The Master addresses a Slave by creating a START

condition and then broadcasting an 8−bit Slave address. For

the CAT24C32, the first four bits of the Slave address are set

to 1010 (Ah); the next three bits, A2, A1 and A0, must match

the logic state of the similarly named input pins. The devices

in WLCSP (C5A and C4C) respond only to the Slave

Address with A2 A1 A0 = 0 0 0. The R/W bit tells the Slave

whether the Master intends to read (1) or write (0) data

(Figure 3).

Acknowledge

During the 9th clock cycle following every byte sent to the

bus, the transmitter releases the SDA line, allowing the

receiver to respond. The receiver then either acknowledges

(ACK) by pulling SDA LOW, or does not acknowledge

(NoACK) by letting SDA stay HIGH (Figure 4). Bus timing

is illustrated in Figure 5.

START

CONDITION

STOP

CONDITION

SDA

SCL

Figure 2. Start/Stop Timing

Figure 3. Slave Address Bits

1010

DEVICE ADDRESS*

A2A1A0R/W

* The devices in WLCSP 4−ball and 5−ball respond only to Slave Address byte with A2 A1 A0 = 0 0 0

CAT24C32

www.onsemi.com

Figure 4. Acknowledge Timing

189

START

SCL FROM

MASTER

BUS RELEASE DELAY (TRANSMITTER) BUS RELEASE DELAY (RECEIVER)

DATA OUTPUT

FROM TRANSMITTER

DATA OUTPUT

FROM RECEIVER

ACK SETUP (≥ tSU:DAT)

ACK DELAY (≤ tAA)

Figure 5. Bus Timing

SCL

SDA IN

SDA OUT

tBUF

tSU:STO

tSU:DAT

tAA tDH

tLOW

tHIGH

tLOW

tSU:STA

tHD:SDA

tHD:DAT

WRITE OPERATIONS

Byte Write

To write data to memory, the Master creates a START

condition on the bus and then broadcasts a Slave address

with the R/W bit set to ‘0’. The Master then sends two

address bytes and a data byte and concludes the session by

creating a STOP condition on the bus. The Slave responds

with ACK after every byte sent by the Master (Figure 6). The

STOP starts the internal Write cycle, and while this

operation is in progress (tWR), the SDA output is tri−stated

and the Slave does not acknowledge the Master (Figure 7).

Page Write

The Byte Write operation can be expanded to Page Write,

by sending more than one data byte to the Slave before

issuing the STOP condition (Figure 8). Up to 32 distinct data

bytes can be loaded into the internal Page Write Buffer

starting at the address provided by the Master. The page

address is latched, and as long as the Master keeps sending

data, the internal byte address is incremented up to the end

of page, where it then wraps around (within the page). New

data can therefore replace data loaded earlier. Following the

STOP, data loaded during the Page Write session will be

written to memory in a single internal Write cycle (tWR).

Acknowledge Polling

As soon (and as long) as internal Write is in progress, the

Slave will not acknowledge the Master. This feature enables

the Master to immediately follow−up with a new Read or

Write request, rather than wait for the maximum specified

Write time (tWR) to elapse. Upon receiving a NoACK

response from the Slave, the Master simply repeats the

request until the Slave responds with ACK.

Hardware Write Protection

With the WP pin held HIGH, the entire memory is

protected against Write operations. If the WP pin is left

floating or is grounded, it has no impact on the Write

operation. The state of the WP pin is strobed on the last

falling edge of SCL immediately preceding the 1st data byte

(Figure 9). If the WP pin is HIGH during the strobe interval,

the Slave will not acknowledge the data byte and the Write

request will be rejected.

Delivery State

The CAT24C32 is shipped erased, i.e., all bytes are FFh.

CAT24C32

www.onsemi.com

SLAVE

ADDRESS

****

BUS ACTIVITY:

MASTER

SLAVE

ADDRESS

BYTE

ADDRESS

BYTE

DATA

BYTE

Figure 6. Byte Write Sequence

*a15 − a12 are don’t care bits

a15 − a8a7 − a0d7 − d0

Figure 7. Write Cycle Timing

STOP

CONDITION START

CONDITION ADDRESS

ACK8th Bit

Byte n

SCL

SDA

tWR

SLAVE

ADDRESS

BUS

ACTIVITY:

MASTER

SLAVE

n = 1

ADDRESS

BYTE

ADDRESS

BYTE

DATA

BYTE

DATA

BYTE

n+1

DATA

BYTE

n+P

Figure 8. Page Write Sequence

P ≤ 31

Figure 9. WP Timing

189

ADDRESS

BYTE

DATA

BYTE

SCL

SDA

tSU:WP

tHD:WP

a7a0d7d0

CAT24C32

www.onsemi.com

READ OPERATIONS

Immediate Read

To read data from memory, the Master creates a START

condition on the bus and then broadcasts a Slave address

with the R/W bit set to ‘1’. The Slave responds with ACK

and starts shifting out data residing at the current address.

After receiving the data, the Master responds with NoACK

and terminates the session by creating a STOP condition on

the bus (Figure 10). The Slave then returns to Standby mode.

Selective Read

To read data residing at a speciﬁc address, the selected

address must ﬁrst be loaded into the internal address register.

This is done by starting a Byte Write sequence, whereby the

Master creates a START condition, then broadcasts a Slave

address with the R/W bit set to ‘0’ and then sends two

address bytes to the Slave. Rather than completing the Byte

Write sequence by sending data, the Master then creates a

START condition and broadcasts a Slave address with the

R/W bit set to ‘1’. The Slave responds with ACK after every

byte sent by the Master and then sends out data residing at

the selected address. After receiving the data, the Master

responds with NoACK and then terminates the session by

creating a STOP condition on the bus (Figure 11).

Sequential Read

If, after receiving data sent by the Slave, the Master

responds with ACK, then the Slave will continue

transmitting until the Master responds with NoACK

followed by STOP (Figure 12). During Sequential Read the

internal byte address is automatically incremented up to the

end of memory, where it then wraps around to the beginning

of memory.

Figure 10. Immediate Read Sequence and Timing

SCL

SDA 8th Bit

STOP

NO ACKDATA OUT

SLAVE

ADDRESS

DATA

BYTE

BUS ACTIVITY

MASTER

SLAVE

Figure 11. Selective Read Sequence

SLAVE

ADDRESS

SLAVE

ADDRESS

BYTE

ADDRESS

BYTE ADDRESS

DATA

BYTE

BUS ACTIVITY:

MASTER

SLAVE

Figure 12. Sequential Read Sequence

SLAVE

ADDRESS

DATA

BYTE

DATA

BYTE

n+1

DATA

BYTE

n+2

DATA

BYTE

n+x

BUS ACTIVITY:

MASTER

SLAVE

CAT24C32

www.onsemi.com

ORDERING INFORMATION

Device Order Number

Specific

Device

Marking

Package

Type Temperature Range

Lead

Finish Shipping†

CAT24C32HU4I−GT3 C5U UDFN8 I = Industrial

(−40°C to +85°C)

NiPdAu Tape & Reel, 3,000 Units / Reel

CAT24C32C5ATR 2 WLCSP5 I = Industrial

(−40°C to +85°C)

SnAgCu Tape & Reel, 5,000 Units / Reel

CAT24C32C5CTR P WLCSP5 with

Die Coat

I = Industrial

(−40°C to +85°C)

SnAgCu Tape & Reel, 5,000 Units / Reel

CAT24C32C4CTR B WLCSP4 with

Die Coat

I = Industrial

(−40°C to +85°C)

SnAg Tape & Reel, 5,000 Units / Reel

CAT24C32XI−T2

(Note 14)

TBD SOIC−8I = Industrial

(−40°C to +85°C)

Matte−Tin Tape & Reel, 2,000 Units / Reel

CAT24C32WI−GT3 24C32F SOIC−8,

JEDEC

I = Industrial

(−40°C to +85°C)

NiPdAu Tape & Reel, 3,000 Units / Reel

CAT24C32YI−GT3 C32F TSSOP−8I = Industrial

(−40°C to +85°C)

NiPdAu Tape & Reel, 3,000 Units / Reel

CAT24C32USI−T3

(In Development)

TBD US8 I = Industrial

(−40°C to +85°C)

Matte−Tin Tape & Reel, 3,000 Units / Reel

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging

Specifications Brochure, BRD8011/D.

10.All packages are RoHS−compliant (Lead−free, Halogen−free).

11. The standard lead finish is NiPdAu.

12.For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging

Specifications Brochure, BRD8011/D.

13.Caution: The EEPROM devices delivered in WLCSP must never be exposed to ultraviolet light. When exposed to ultraviolet light

the EEPROM cells lose their stored data.

14.In development.

ON Semiconductor is licensed by the Philips Corporation to carry the I2C bus protocol.

UDFN8, 2x3 EXTENDED PAD

CASE 517AZ

ISSUE A DATE 23 MAR 201

SCALE 2:1

NOTES:

1. DIMENSIONING AND TOLERANCING PER

ASME Y14.5M, 1994.

2. CONTROLLING DIMENSION: MILLIMETERS.

3. DIMENSION b APPLIES TO PLATED

TERMINAL AND IS MEASURED BETWEEN

0.15 AND 0.25MM FROM THE TERMINAL TIP.

4. COPLANARITY APPLIES TO THE EXPOSED

PAD AS WELL AS THE TERMINALS.

ÇÇ

C0.10

PIN ONE

REFERENCE

TOP VIEW

SIDE VIEW

BOTTOM VIEW

C0.10

C0.08 A1 SEATING

PLANE

NOTE 3

0.10 C

0.05 C

DIM MIN MAX

MILLIMETERS

A0.45 0.55

A1 0.00 0.05

b0.20 0.30

D2.00 BSC

D2 1.35 1.45

E3.00 BSC

E2 1.25 1.35

e0.50 BSC

L0.25 0.35

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

SOLDERING FOOTPRINT*

0.50

PITCH

1.45 3.40

DIMENSIONS: MILLIMETERS

NOTE 4

0.30

DET AIL A

A3 0.13 REF

DETAIL B

L1 DETAIL A

ALTERNATE

CONSTRUCTIONS

L1 −−− 0.15

RECOMMENDED

1.56

GENERIC

MARKING DIAGRAM*

XXXXX = Specific Device Code

A = Assembly Location

WL = Wafer Lot

Y = Year

W = Work Week

G= Pb−Free Package

*This information is generic. Please refer to

device data sheet for actual part marking.

Pb−Free indicator, “G” or microdot “ G”,

may or may not be present.

XXXXX

AWLYWG

0.68

C0.10

ÉÉ

ÇÇ

DETAIL B

MOLD CMPDEXPOSED Cu

ALTERNATE

CONSTRUCTIONS

ÉÉÉ

ÇÇÇ

MECHANICAL CASE OUTLINE

PACKAGE DIMENSIONS

http://onsemi.com

October, 2002 − Rev. 0 Case Outline Number:

XXX

DOCUMENT NUMBER:

STATUS:

REFERENCE:

DESCRIPTION:

98AON42552E

ON SEMICONDUCTOR STANDARD

UDFN8, 2X3 EXTENDED PAD

Electronic versions are uncontrolled except when

accessed directly from the Document Repository. Printed

versions are uncontrolled except when stamped

“CONTROLLED COPY” in red.

PAGE 1 OF 2

DOCUMENT NUMBER:

98AON42552E

PAGE 2 OF 2

ISSUE REVISION DATE

ORELEASED FOR PRODUCTION FROM POD #UDFN8−046−01 TO ON SEMICON-

DUCTOR. REQ. BY B. BERGMAN. 23 JUL 2009

AREDREW PACKAGE DRAWING TO ON SEMICONDUCTOR/JEDEC STANDARD.

REQ. BY B. BECKER. 23 MAR 2015

March, 2015 − Rev. A Case Outline Number

517AZ

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice

to any products herein. SCILLC makes no warranty , representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability

arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.

“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All

operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights

nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications

intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should

Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, af filiates,

and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death

associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal

Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

WLCSP5, 1.34x0.91

CASE 567JQ

ISSUE A DATE 09 JUN 2015

SEATING

PLANE

0.10 C

NOTES:

1. DIMENSIONING AND TOLERANCING PER ASME

Y14.5M, 1994.

2. CONTROLLING DIMENSION: MILLIMETERS.

3. COPLANARITY APPLIES TO THE SPHERICAL

CROWNS OF THE SOLDER BALLS.

4. DIMENSION b IS MEASURED AT THE MAXIMUM

BALL DIAMETER PARALLEL TO DATUM C.

2X DIM

AMIN MAX

−−−

MILLIMETERS

D1.34 BSC

b0.16 0.20

e0.40 BSC

0.35

ÈÈ

PIN A1

REFERENCE

A0.05 BC

0.03 C

0.05 C

5X b

0.10 C

0.08 0.12

0.91 BSC

e1 0.693 BSC

SCALE 4:1

0.18

DIMENSIONS: MILLIMETERS

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

SOLDERING FOOTPRINT*

0.69

0.10 C

2X T OP VIEW

SIDE VIEW

BOTTOM VIEW

NOTE 3

A2 0.23 REF

RECOMMENDED

A1 PACKAGE

OUTLINE

PITCH

0.40

PITCH

X = Specific Device Code

Y = Year

W = W ork Week

*This information is generic. Please refer to

device data sheet for actual part marking.

Pb−Free indicator, “G” or microdot “ G”,

may or may not be present.

GENERIC

MARKING DIAGRAM*

XYW

DETAIL A

DIE COAT A3

(OPTIONAL)

DET AIL A

A3 0.025 REF

MECHANICAL CASE OUTLINE

PACKAGE DIMENSIONS

http://onsemi.com

October, 2002 − Rev. 0 Case Outline Number:

XXX

DOCUMENT NUMBER:

STATUS:

NEW STANDARD:

DESCRIPTION:

98AON82067F

ON SEMICONDUCTOR STANDARD

WLCSP5, 1.34X0.91

Electronic versions are uncontrolled except when

acc essed d irectly f rom the Doc ument R epository. Printed

versions are uncontrolled except when stamped

“CONTROLLED COPY” in red.

PAGE 1 OF 2

DOCUMENT NUMBER:

98AON82067F

PAGE 2 OF 2

ISSUE REVISION DATE

ORELEASED FOR PRODUCTION. REQ. BY I. MARIANO. 04 FEB 2014

AADDED BACKSIDE COATING OPTION AND DETAIL A. REQ. BY B. BECKER. 09 JUN 2015

June, 2015 − Rev. A Case Outline Number

568JQ

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice

to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any

liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental

damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over

time. All operating parameters, including “Typicals” must be validated for each customer application by customer ’s technical experts. SCILLC does not convey any license under

its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body,

or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death

may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees,

subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of

personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part.

SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

ÈÈ

WLCSP4, 0.77x0.77

CASE 567JY

ISSUE C DATE 07 MAR 2017

SEATING

PLANE

PIN A1

REFERENCE

A0.05 BC

0.03 C

0.05 C

4X b

0.05 C

SCALE 4:1

T OP VIEW

SIDE VIEW

BOTTOM VIEW

NOTE 4

PITCH 0.16

DIMENSIONS: MILLIMETERS

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

SOLDERING FOOTPRINT*

0.40 0.40

RECOMMENDED

1PACKAGE

OUTLINE

PITCH

DET AIL A

NOTES:

1. DIMENSIONING AND TOLERANCING PER ASME

Y14.5M, 1994.

2. CONTROLLING DIMENSION: MILLIMETERS.

3. DATUM C, THE SEATING PLANE, IS DEFINED BY THE

SPHERICAL CROWNS OF THE SOLDER BALLS.

4. COPLANARITY APPLIES TO SPHERICAL CROWNS OF

THE SOLDER BALLS.

5. DIMENSION b IS MEASURED AT THE MAXIMUM

CONTACT BALL DIAMETER PARALLEL TO DATUM C.

6. BACKSIDE COATING IS OPTIONAL.

DIM

AMIN NOM

−−−

MILLIMETERS

b0.15 0.155

e0.40 BSC

−−−

0.04 0.06

A2 0.23 REF

A3 0.025 REF

0.75 0.77

MAX

0.16

0.35

0.08

0.79

DETAIL A

NOTE 6

DIE COAT

(OPTIONAL) A3

X = Specific Device Code

Y = Year

W = W ork Week

*This information is generic. Please refer to

device data sheet for actual part marking.

Pb−Free indicator, “G” or microdot “ G”,

may or may not be present.

GENERIC

MARKING DIAGRAM*

NOTE 5

NOTE 3

MECHANICAL CASE OUTLINE

PACKAGE DIMENSIONS

http://onsemi.com

October, 2002 − Rev. 0 Case Outline Number:

XXX

DOCUMENT NUMBER:

STATUS:

NEW STANDARD:

DESCRIPTION:

98AON85186F

ON SEMICONDUCTOR STANDARD

WLCSP4, 0.77X0.77

Electronic versions are uncontrolled except when

acc essed d irectly f rom the Doc ument R epository. Printed

versions are uncontrolled except when stamped

“CONTROLLED COPY” in red.

PAGE 1 OF 2

DOCUMENT NUMBER:

98AON85186F

PAGE 2 OF 2

ISSUE REVISION DATE

ORELEASED FOR PRODUCTION. REQ. BY I. MARIANO. 06 MAY 2014

ACORRECTED DETAIL A AND DIMENSION A1, ADDED NOMINAL VALUES. REQ.

BY V. CRACIUNOIU. 23 JUN 2016

BMODIFIED DIMENSIONS D AND E TO 0.77X0.77. REQ. BY V. CRACIUNOIU. 02 AUG 2016

CMODIFIED DIMENSIONS A1 AND A2 VALUES. REQ. BY V. CRACIUNOIU. 07 MAR 2017

March, 2017 − Rev. C Case Outline Number

567JY