HA17358A Series Dual Operational Amplifier REJ03D0676-0300 (Previous: ADE-204-033B) Rev.3.00 Jun 15, 2005 Description HA17358A series are dual operational amplifier that provide high gain and internal phase compensation, with single power supply. They can be widely applied to control equipments and to general use. Features * Wide range of supply voltage, and single power supply used * Wide range of common mode voltage, and possible to operate with an input about 0 V, and output around 0 V is available * Frequency characteristics and input bias current are temperature compensated * Low electro-magnetic susceptibility level Measurement Condition 5.0 Output Offset Voltage vs. Input Interference Rs Rs - + Rf 0.01 Vin -10 dBm RF signal source (for quasi-RF noise) Vout V _ (= 100Vio) Output offset voltage (arb. unit) Rf Vcc = +7.5 V Vee = -7.5 V 4.0 HA17358 series 3.0 2.0 Improvement 1.0 HA17358A series 0 -1.0 100E+3 1E+6 10E+6 100E+6 1E+9 Input RF frequency (Hz) 10E+9 Ordering Information Type No. HA17358A HA17358AF HA17358ARP HA17358AT Rev.3.00 Jun 15, 2005 page 1 of 7 Application Commercial use Package Code (Previous Code) PRDP0008AF-A (DP-8B) PRSP0008DE-B (FP-8DGV) PRSP0008DD-C (FP-8DCV) PTSP0008JC-B (TTP-8DAV) HA17358A Series Pin Arrangement Vout1 1 Vin(-)1 2 Vin(+)1 3 GND 4 1 - + 2 + - 8 VCC 7 Vout2 6 Vin(-)2 5 Vin(+)2 (Top View) Circuit Schematic (1/2) Q5 Vin(-) Q1 Q2 Q3 Q4 Q6 C Q7 R1 Vin(+) Vout Q11 Q10 Q8 Rev.3.00 Jun 15, 2005 page 2 of 7 Q9 Q13 Q12 HA17358A Series Absolute Maximum Ratings (Ta = 25C) Item Symbol Ratings HA17358A HA17358AF/ARP Unit 32 50 V mA Supply voltage Sink current VCC Isink 32 50 Power dissipation Common mode input voltage PT VCM 570 * -0.3 to VCC 385 * -0.3 to VCC mW V Differential input voltage Operating temperature Vin (diff) Topr VCC -40 to +85 VCC -40 to +85 V C 1 2 Storage temperature Tstg -55 to +125 -55 to +125 C Notes: 1. This is the allowable values up to Ta = 50C. Derate by 8.3 mW/C. 2. These are the allowable values up to Ta = 25C mounting in air. When it is mounted on glass epoxy board of 40 mm x 40 mm x 1.5 mmt with 30% wiring density, the allowable value is 570 mW up to Ta = 45C. If Ta > 45C, derate by 7.14 mW/C. Electrical Characteristics (VCC = +15 V, Ta = 25C) Item Symbol Min Typ Max Unit Test Conditions Input offset voltage Input offset current VIO IIO -- -- 3 5 7 50 mV nA VCM = 7.5V, RS = 50, Rf = 50k VCM = 7.5V, IIO = | II (+) - II (-) | Input bias current Power source rejection ratio IIB PSRR -- -- 30 93 250 -- nA dB VCM = 7.5V RS = 1k, Rf = 100k Voltage gain Common mode rejection ratio AVD CMR 75 -- 90 80 -- -- dB dB RL = , RS = 1k, Rf = 100k RS = 50, Rf = 5k Common mode input voltage range VCM (+) VCM (-) 13.5 -- -- -- -- -0.3 V V RS = 1k, Rf = 100k RS = 1k, Rf = 100k Peak-to-peak output voltage Vop-p -- 13.6 -- V Output source current Iosource 20 40 -- mA f = 100Hz, RL = 20k, RS = 1k, Rf = 100k + - VIN = 1V, VIN = 0V, VOH = 10V Output sink current Output sink current Iosink Iosink 10 15 20 50 -- -- mA A VIN = 1V, VIN = 0V, VOL = 2.5V - + VIN = 1V, VIN = 0V, Vout = 200mV Supply current Slew rate ICC SR -- -- 0.8 0.2 2 -- mA V/s VIN = GND, RL = RL = , VCM = 7.5V, f = 1.5kHz Channel separation CS -- 120 -- dB Rev.3.00 Jun 15, 2005 page 3 of 7 - f = 1kHz + HA17358A Series Output Source Current vs. Ambient Temperature 80 VCC = 15 V 70 VOH = 10 V 60 50 40 30 20 10 0 -20 0 20 40 60 Ambeint temperature Ta (C) Input Bias Current vs. Ambient Temperature 80 Input bias current IIB (nA) Output source current Iosource (mA) Characteristic Curves VCC = 15 V VCM = 7.5 V 70 60 50 40 30 20 10 0 -20 80 2 1 8 16 24 32 Supply voltage VCC (V) 80 Input bias current IIB (nA) Supply current ICC (mA) Ta = 25C 3 0 40 20 0 40 120 80 40 40 Maximum output voltage VOP-P (V) Voltage gain AVD (dB) Ta = 25C RL = Rev.3.00 Jun 15, 2005 page 4 of 7 8 16 24 32 Supply voltage VCC (V) 40 Maxlmum Output Voltage vs. Frequency 160 8 16 24 32 Supply voltage VCC (V) Ta = 25C 60 Voltage Gain vs. Supply Voltage 0 80 Input Bias Current vs. Supply Voltage Supply Current vs. Supply Voltage 4 0 20 40 60 Ambeint temperature Ta (C) 20 VCC = 15 V Ta = 25C RL = 20 k 16 12 8 4 0 1k 3k 10 k 30 k 100 k 300 k Frequency f (Hz) 1M HA17358A Series Voltage Gain vs. Frequency 120 VCC = 15V Ta = 25C RL = Voltage gain AVD (dB) 100 80 60 40 20 0 1 3 10 30 100 300 1k 3k Frequency f (Hz) 10 k 30 k 100 k 300 k Common Mode Rejection Ratio vs. Frequency Common mode rejection ratio CMR (dB) 120 VCC = 15V Ta = 25C RS = 50 100 80 60 40 20 0 100 Rev.3.00 Jun 15, 2005 page 5 of 7 300 1k 3 k 10 k 30 k 100 k 300 k Frequency f (Hz) 1M 1M HA17358A Series Package Dimensions JEITA Package Code P-DIP8-6.3x9.6-2.54 RENESAS Code PRDP0008AF-A Previous Code DP-8B MASS[Typ.] 0.51g D 5 E 8 1 4 b3 0.89 Z Reference Symbol Dimension in Millimeters Min Nom 7.62 D 9.6 E 6.3 Max A1 A e1 L A1 0.5 bp 0.38 c e1 0.48 c 0.20 0 e 2.29 0.25 0.35 2.54 2.79 15 1.27 Z 2.54 L JEITA Package Code P-SOP8-4.4x4.85-1.27 RENESAS Code PRSP0008DE-B *1 Previous Code FP-8DGV MASS[Typ.] 0.1g F D 8 0.58 1.3 b3 bp 7.4 5.06 A e 10.6 NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. 5 c *2 E HE bp Reference Symbol Terminal cross section ( Ni/Pd/Au plating ) Z e Min Nom Max 4.85 5.25 E 4.4 A2 4 1 Dimension in Millimeters D Index mark *3 bp A1 x M 0.00 0.1 0.35 0.4 0.45 0.15 0.20 0.25 6.5 6.75 A 2.03 bp L1 0.20 b1 c A c1 A1 L y Detail F 0 HE 6.35 e 1.27 x 0.12 y 0.15 0.75 Z L L Rev.3.00 Jun 15, 2005 page 6 of 7 8 0.42 1 0.60 1.05 0.85 HA17358A Series JEITA Package Code P-SOP8-3.95x4.9-1.27 RENESAS Code PRSP0008DD-C *1 Previous Code FP-8DCV MASS[Typ.] 0.085g NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. F D 8 5 c *2 E HE bp Index mark Reference Symbol Terminal cross section ( Ni/Pd/Au plating ) Dimension in Millimeters Min Nom Max D 4.90 5.30 E 3.95 A2 4 1 *3 e Z A1 bp x M L1 A c A1 L y Detail F 8 0.40 0.46 0.15 0.20 0.25 6.10 6.20 0 HE 5.80 8 1.27 e x 0.25 y 0.10 0.75 Z L 0.40 0.60 1.27 1.08 1 MASS[Typ.] 0.034g Previous Code TTP-8DAV D 0.34 1 L *1 0.25 b1 c RENESAS Code PTSP0008JC-B 0.14 1.75 bp JEITA Package Code P-TSSOP8-4.4x3-0.65 0.10 A F 5 NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. c HE *2 E bp Reference Symbol Terminal cross section ( Ni/Pd/Au plating ) Dimension in Millimeters Min Nom Max D 3.00 3.30 E 4.40 A2 Index mark A1 0.03 0.07 0.15 0.20 0.25 0.10 0.15 0.20 6.40 6.60 A L1 0.10 1.10 bp b1 1 4 e c *3 bp x c1 M A1 A Z L Detail F y 0 HE 6.20 e 0.65 x 0.13 y 0.10 0.805 Z L L Rev.3.00 Jun 15, 2005 page 7 of 7 8 0.40 1 0.50 1.00 0.60 Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology (Shanghai) Co., Ltd. Unit2607 Ruijing Building, No.205 Maoming Road (S), Shanghai 200020, China Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 (c) 2005. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon 2.0