Contacts www.amphenol-socapex.com Amphenol Table of contents TABLE OF CONTENTS 1. DESIGN, SCREW MACHINING AND PLATING CAPABILITY 6-7 2. SIGNAL CONTACTS 8-15 a. Crimp contacts - MILITARY STANDARD b. Crimp contacts - EUROPEAN STANDARD c. PCB contacts d. Thermo-couples contacts 8-11 12-13 14 15 3. POWER CONTACTS 16-19 a. Size 8 contacts b. Specific range of products c. Amphenol Radsok technology 16-17 17 18 4. COAXIAL CONTACTS 20-33 a. Introduction b. STANDARD PERFORMANCES i. Crimp contacts - MIL-DTL-38999 series II / EN4165 20 21-24 21 22-23 ii. Crimp contacts -MIL-DTL-38999 series I,III / EN3645 c. IMPEDANCE MATCHED COAXIAL CONTACTS 24-25 i. Crimp contacts - MIL-DTL-38999 series I, II, III / EN3645/EN4165 d. TYPICAL CONTACT INSTALLATION INSTRUCTIONS 25 e. PRINT CIRCUIT board contacts 26-27 f. RF COAXIAL CONTACTS 28-30 g. 75 OHMS COAXIAL CONTACTS 31-32 5. TWINAX CONTACTS 34-39 a. Introduction b. Crimp contacts - MILITARY STANDARD 34 35 c. Crimp contacs - EUROPEAN and AIRBUS STANDARD 36 d. Crimp contacts - 1760 INTERFACE 37 e. Crimp contacts - ARINC 600 37 f. TYPICAL CONTACT INSTALLATION INSTRUCTIONS 38 g. PCB contacts 39 6. DIFFERENTIAL TWINAX CONTACTS 40-41 7. QUADRAX CONTACTS 42-47 a. Introduction b. Crimp contacts c. TYPICAL CONTACT INSTALLATION INSTRUCTIONS d. PCB Contacts e. Crimp and PCB contacts - ARINC 600 2 24 Table of contents 42 43 44 45 46 Table of contents Amphenol TABLE OF CONTENTS 8. SPLIT PAIR QUADRAX CONTACTS 48 9. COM CONTACTS 49 10. High-speed cordsets 50 11. OPTICAL TERMINI 51-57 a. M29504/4 & /5 b. Lux-Beam expanded beam contacts c. Lumiere (EN4531 - ELIO) d. ARINC801 52 53-55 56 57 12. ACCESSORIES 58-59 13. GLOSSARY 60-61 14. CONTACT AND CABLE SELECTION GUIDE a. COAXIAL CONTACTS b. TWINAXIAL CONTACTS 62-67 62-65 66 Table of contents 3 Amphenol INDEX P/N Pin or Socket Type 140675 Pin TWINAX Contact ABS 1600 AND ABS 1607 P/N Pin or Socket Type P/N Pin or Socket Type 37 140683 Socket 250711 Socket 250712 600513 600907 Pin Impedance Matched Coaxial Contact 24 603116 Pin QUADRAX CONTACTS FOR ARINC600 TWINAX Contact ABS 1600 AND ABS 1607 37 600908 Pin Impedance Matched Coaxial Contact 24 603160 Socket Power contact 16 Thermo-couple 15 600909 Socket 75OHMS Coaxial Contact - PCB 32 603161 Piggy Back Grommet 75OHMS Coaxial Contact 32 Socket Thermo-couple 15 600910 Socket Shielded Coaxial contact 23 603177 Pin QUADRAX CONTACTS FOR ARINC600 - PCB 46 Pin QUADRAX CONTACTS 43 600911 Socket Shielded Coaxial contact 23 Socket Pin QUADRAX CONTACTS 43 75OHMS Coaxial Contact 31 600514 603180 600912 Socket Shielded Coaxial contact 23 600515 43 600913 QUADRAX CONTACTS FOR ARINC600 46 QUADRAX CONTACTS 603209 Socket Socket Socket Shielded Coaxial contact 23 600914 603210 Socket 46 Socket Shielded Coaxial contact 23 QUADRAX CONTACTS FOR ARINC600 603228 Pin QUADRAX CONTACTS FOR ARINC600 - PCB 46 603229 Socket QUADRAX CONTACTS FOR ARINC600 - PCB 46 603247 Socket Shielded Coaxial contact 22 600516 600520 QUADRAX CONTACTS Socket QUADRAX CONTACTS -PCB 43 45 600526 Socket Signal contact LI 14 600580 Socket RF Coaxial Contact 30 600581 Socket RF Coaxial Contact 30 600915 600916 Socket Socket Pages Impedance Matched Coaxial Contact 24 Impedance Matched Coaxial Contact 24 Pages 46 17 600917 Socket Impedance Matched Coaxial Contact 24 900000 Pin Signal contact 8 10 600918 Socket Impedance Matched Coaxial Contact 24 900001 Pin Signal contact 8 10 600919 Socket RF Coaxial Contact 30 900004 Pin Signal contact 8 10 57 600920 Pin RF Coaxial Contact 30 900005 Pin Signal contact 8 10 57 600921 Pin RF Coaxial Contact 30 900010 Socket Signal contact 8 10 600922 Pin RF Coaxial Contact 30 900011 Socket Signal contact 8 10 600923 Pin RF Coaxial Contact 30 900014 Socket Signal contact 8 10 900020 SEALING PLUGS 58 900021 SEALING PLUGS 58 900022 SEALING PLUGS 58 600600 Pin RF Coaxial Contact 30 600606 Pin RF Coaxial Contact 30 600611 Pin TWINAX Contact - EN or ABS 36 600612 Pin TWINAX Contact - EN or ABS 36 600613 Pin TWINAX Contact - EN or ABS 36 600614 Socket TWINAX Contact - EN or ABS 36 600924 Pin RF Coaxial Contact 30 600615 Socket TWINAX Contact - EN or ABS 36 600925 Socket RF Coaxial Contact 30 600616 Socket TWINAX Contact - EN or ABS 36 600926 Socket RF Coaxial Contact 30 600659 Socket Impedance Matched Coaxial Contact 24 600927 Socket RF Coaxial Contact 30 600929 30 SEALING PLUGS 58 39 RF Coaxial Contact 900022 TWINAX - PCB Pin 600930 Socket RF Coaxial Contact 30 900023 SEALING PLUGS 58 600931 Pin DIFFERENTIAL TWINAX CONTACTS 41 900024 SEALING PLUGS 58 600932 Socket DIFFERENTIAL TWINAX CONTACTS 41 900025 DUMMY CONTACS 58 600933 Pin DIFFERENTIAL TWINAX CONTACTS 41 900026 DUMMY CONTACS 58 600934 Socket DIFFERENTIAL TWINAX CONTACTS 41 900028 DUMMY CONTACS 58 600935 Pin DIFFERENTIAL TWINAX CONTACTS 41 900029 DUMMY CONTACS 600936 Socket DIFFERENTIAL TWINAX CONTACTS 41 900040 Socket Signal contact 8 10 600938 Socket DIFFERENTIAL TWINAX CONTACTS 41 900041 Socket Signal contact 8 10 900044 Socket Signal contact 8 10 900045 Socket Signal contact 8 10 600709 Socket 75OHMS Coaxial Contact 31 Shielded Coaxial contact CI 26 Impedance Matched Coaxial Contact 26 Piggy Back Grommet 75OHMS Coaxial Contact 31 Socket Impedance Matched Coaxial Contact 24 75OHMS Coaxial Contact 31 Piggy Back Grommet 75OHMS Coaxial Contact 31 600813 Pin 75OHMS Coaxial Contact 31 600822 Pin 75OHMS Coaxial Contact 32 600830 Pin 75OHMS Coaxial Contact 32 600715 600748 600749 600749 600750 600757 600762 Socket Socket Socket Pin Socket 75OHMS Coaxial Contact 32 600841 Socket 75OHMS Coaxial Contact 32 600850 Pin TWINAX Contact - MIL 35 600836 600851 600939 DIFFERENTIAL TWINAX CONTACTS 41 600940 Socket DIFFERENTIAL TWINAX CONTACTS 41 900048 Socket Signal contact 8 10 600941 Pin DIFFERENTIAL TWINAX CONTACTS 41 900049 Pin Signal contact 8 10 600942 Socket DIFFERENTIAL TWINAX CONTACTS 41 900075 Socket Shielded Coaxial contact 22 600943 Pin DIFFERENTIAL TWINAX CONTACTS 41 900090 REDUCING FERRULE 59 600944 Socket DIFFERENTIAL TWINAX CONTACTS 41 900091 REDUCING FERRULE 59 600945 Pin DIFFERENTIAL TWINAX CONTACTS 41 900092 REDUCING FERRULE 59 600946 Socket DIFFERENTIAL TWINAX CONTACTS 41 900093 REDUCING FERRULE 59 600947 Pin DIFFERENTIAL TWINAX CONTACTS 41 900094 REDUCING FERRULE 59 600948 Socket DIFFERENTIAL TWINAX CONTACTS 41 900099 REDUCING FERRULE 600951 Pin QUADRAX CONTACTS 43 900130 Pin Shielded Coaxial contact 23 600952 Socket QUADRAX CONTACTS 43 900135 Pin Shielded Coaxial contact 23 600953 Pin QUADRAX CONTACTS 43 900136 Pin Shielded Coaxial contact 23 600954 Socket QUADRAX CONTACTS 43 900137 Pin Shielded Coaxial contact 23 TWINAX Contact - MIL Pin TWINAX Contact - EN or ABS Socket TWINAX Contact - EN or ABS Pin TWINAX Contact - EN or ABS Socket TWINAX Contact - EN or ABS 600858 Pin TWINAX Contact - EN or ABS 36 600858 Pin DIFFERENTIAL TWINAX CONTACTS 41 600859 Socket TWINAX Contact - EN or ABS 36 600863 Pin Power contact 16 17 600955 Pin QUADRAX CONTACTS 43 900138 Pin Shielded Coaxial contact 23 600864 Pin Power contact 16 17 600956 Socket QUADRAX CONTACTS 43 900140 Socket Shielded Coaxial contact 23 600865 Socket Power contact 16 17 600958 Socket QUADRAX CONTACTS 43 900145 Socket Shielded Coaxial contact 23 600866 Socket Signal contact LI 14 600959 Pin QUADRAX CONTACTS 43 900146 Socket Shielded Coaxial contact 23 600867 Pin Signal contact LI 14 600960 Socket QUADRAX CONTACTS 43 900147 Socket Shielded Coaxial contact 23 600889 Pin 75OHMS Coaxial Contact - PCB 32 600961 Pin QUADRAX CONTACTS 43 900148 Socket Shielded Coaxial contact 23 600899 Socket DIFFERENTIAL TWINAX CONTACTS 41 600962 Socket QUADRAX CONTACTS 43 900154 REDUCING FERRULE 600900 Pin Shielded Coaxial contact 23 600963 Pin QUADRAX CONTACTS - EN 43 900179 Pin Shielded Coaxial contact CI 26 600901 Pin Shielded Coaxial contact 23 600964 Socket QUADRAX CONTACTS - EN 43 600902 900183 DUMMY CONTACS Pin Shielded Coaxial contact 23 600987 Pin QUADRAX CONTACTS 43 600903 Pin Shielded Coaxial contact 23 603015 Piggy Back Grommet Shielded Coaxial contact CI 26 Pin 900184 58 900186 Pin Shielded Coaxial contact 62 603016 Piggy Back Grommet 58 900186 DUMMY CONTACS 603085 Pin 43 900187 Socket Shielded Coaxial contact 21 603086 Socket QUADRAX CONTACTS - EN 43 900197 Pin Power contact 16 59 603113 Pin QUADRAX CONTACTS FOR ARINC600 46 900198 Pin Power contact 16 59 600855 600856 600857 35 Pin 58 Socket 600854 36 36 36 36 600904 Pin Shielded Coaxial contact 23 600905 Pin Impedance Matched Coaxial Contact 24 Pin Impedance Matched Coaxial Contact 24 Pin Impedance Matched Coaxial Contact 24 600906 600907 4 Socket Pages Table of contents QUADRAX CONTACTS - EN 59 59 58 27 58 59 Amphenol INDEX P/N Pin or Socket Type 900210 Pin QUADRAX CONTACTS -PCB 45 Pages P/N Pin or Socket Type 900458 Pin Signal contact CI 900217 Socket Power contact 16 900238 Pin Signal contact CI 14 900459 Socket Signal contact CI 900471 Piggy Back Grommet 900240 Pin Signal contact CI 14 900472 Piggy Back Grommet 16 900241 Pin Signal contact CI 14 900476 Piggy Back Grommet 900243 900245 Pin Signal contact LI 14 900488 Pin Signal contact CI 14 DUMMY CONTACS 59 P/N Pin or Socket Type 14 Pages 072503 Socket Thermo-couple 13 14 074834 Pin TWINAX Contact - MIL 33 16 076588 Socket TWINAX Contact 1760 interface 35 076589 Socket TWINAX Contact 1760 interface 35 58 076590 Pin TWINAX Contact - 1760 interface 35 35 32 58 076915 Pin TWINAX Contact 1760 interface 26 077516 Socket TWINAX Contact 1760 interface 35 900489 Pin Shielded Coaxial contact LI 900496 Pin QUADRAX CONTACTS 43 077517 Pin TWINAX Contact 1760 interface 35 900928 Socket RF Coaxial Contact 30 077987 Socket Shielded Coaxial contact 19 900937 Pin DIFFERENTIAL TWINAX CONTACTS 41 900246 Pin Signal contact LI 14 900251 Socket Signal contact CI 14 900252 Socket Signal contact LI 14 900256 Socket Signal contact CI 14 900263 Socket Signal contact CI 14 922390 Socket Signal contact LI 14 900286 Socket Shielded Coaxial contact 21 60020802 Socket Signal contact 8 10 900294 Pin DIFFERENTIAL TWINAX CONTACTS 41 60023302 Pin Signal contact 8 10 900299 Socket DIFFERENTIAL TWINAX CONTACTS 41 60087001 Socket Signal contact 12 13 Socket Signal contact 12 13 Shielded Coaxial contact 41 60087101 60087201 Socket Signal contact 12 13 60087301 Socket Signal contact 12 13 60087401 Socket Signal contact 12 13 60087501 Socket Signal contact 12 13 60087601 Socket Signal contact 12 13 60087701 Socket Signal contact 12 13 60088001 Pin Signal contact 12 13 60088002 Pin Signal contact 8 10 60088101 Pin Signal contact 12 13 60088201 Pin Signal contact 12 13 60088202 Pin Signal contact 8 10 60088301 Pin Signal contact 12 13 60088401 Pin Signal contact 12 13 43 60088402 Pin Signal contact 8 10 58 60088501 Pin Signal contact 12 13 900309 Pin 900310 Socket Shielded Coaxial contact 41 900310 Socket Shielded Coaxial contact 22 900317 Pin 900318 Pin 900319 Pin 900320 Pin 900322 Socket 900323 Socket Signal contact 8 10 900324 Socket Signal contact 8 10 900325 Socket 900327 Pin 900329 DUMMY CONTACS 900330 Pin 900332 DUMMY CONTACS 900337 Socket QUADRAX CONTACTS 43 60088601 Pin Signal contact 12 13 900338 Socket QUADRAX CONTACTS 43 60088602 Pin Signal contact 8 10 900340 Pin Shielded Coaxial contact 21 22 60088701 Pin Signal contact 12 13 900341 Pin Shielded Coaxial contact 21 22 60089001 Socket Signal contact 12 13 900350 Socket Shielded Coaxial contact 22 60089002 Socket Signal contact 8 10 900351 Socket Shielded Coaxial contact 22 60089101 Socket Signal contact 12 13 900354 Socket Shielded Coaxial contact 21 60089201 Socket Signal contact 12 13 900361 Socket QUADRAX CONTACTS 43 60089202 Socket Signal contact 8 10 900384 Pin Impedance Matched Coaxial Contact 24 60089301 Socket Signal contact 12 13 900385 Pin Impedance Matched Coaxial Contact 24 60089401 Socket Signal contact 12 13 900389 Pin Signal contact LI 14 60089402 Socket Signal contact 8 10 900395 Socket Impedance Matched Coaxial Contact 24 60089501 Socket Signal contact 12 13 900403 Socket Signal contact CI 14 60089601 Socket Signal contact 12 13 Socket Shielded Coaxial contact CI 26 60089602 Socket Signal contact 8 10 60089701 Socket Signal contact 12 13 050741 Socket SPLIT PAIR QUADREX CONTACTS 48 050742 Pin SPLIT PAIR QUADREX CONTACTS 48 050998 Pin QUADRAX CONTACTS 43 050999 Socket QUADRAX CONTACTS 43 070247 Pin Shielded Coaxial contact 21 070248 Socket Shielded Coaxial contact 22 900405 Signal contact Signal contact Signal contact Signal contact Signal contact Signal contact QUADRAX CONTACTS 8 8 8 8 8 8 22 10 10 10 10 10 10 43 58 QUADRAX CONTACTS 900409 Pin Shielded Coaxial contact LI 26 900410 Pin QUADRAX CONTACTS 43 27 900411 Socket QUADRAX CONTACTS 43 900412 Socket Impedance Matched Coaxial Contact 26 Pin Signal contact LI 14 900418 Pin DIFFERENTIAL TWINAX CONTACTS 900419 Socket DIFFERENTIAL TWINAX CONTACTS 41 070586 Pin Thermo-couple 15 900420 Socket Shielded Coaxial contact 21 070587 Pin Thermo-couple 15 900421 Socket Shielded Coaxial contact 22 071094 Pin Shielded Coaxial contact 21 900422 Socket Shielded Coaxial contact 22 071315 Socket Signal contact 8 10 900423 Socket Signal contact LI 14 071954 Pin Shielded Coaxial contact 21 22 900424 Pin Shielded Coaxial contact 21 071965 Socket Shielded Coaxial contact 22 900425 Socket Shielded Coaxial contact 21 071998 Socket Shielded Coaxial contact 21 900426 Pin Shielded Coaxial contact 21 072265 Pin TWINAX - PCB 39 900427 Socket Shielded Coaxial contact 21 072453 Socket TWINAX Contact - MIL 35 900428 Pin Shielded Coaxial contact 21 072500 Socket Thermo-couple 15 900429 Socket Shielded Coaxial contact 21 072501 Pin Thermo-couple 15 900430 Socket Shielded Coaxial contact 22 072502 Pin Thermo-couple 15 900413 41 22 22 22 56 Pages 22 56 22 Table of contents 5 Design Screw machining operations Plating capabilities Amphenol Design - Screw machining operations Plating capabilities DESIGN Amphenol Socapex drives innovation through products since years. Thanks to our localization in the Arves valley and our integrated organization, Amphenol acquires a strong knowledge on design and manufacturing of contacts. Our team can support customer requests and offer the right design for the right application. QUICK FACTS ProEngineer software link to a mechanical software analysis CST software to characterize high speed contacts Engineering laboratory for: Mechanical measurements SCREW MACHINING OPERATIONS Our screw machining operations based in Thyez work independently. They manage both internal requests for Amphenol and demands from outside companies. QUICK FACTS A park for all series from 1 to 100 000 pieces, and more. Maximal diameter workable: 10mm Machined parts with slots, milling, axial holes, radial or eccentric holes, thread, tapping, contacts woth wire wrap terminations and winchester. Deburring and polishing by tribofinishing or dry sand blasting. Heat treatment under controlled atmosphere (beryllium copper). Local induction annealing on contacts. Standard metal on stock: beryllium copper, brass, brass for crimping, steel, stainless steel. Capability to have a combined project with plating including cadmium plating, electroless nickel-plating, nickel + gold plating, silver plating, tin plating, passivating for stainless steel. Quick turn-around: quick delivery for small quantities. PLATING CAPABILITIES Amphenol Socapex provides you with plating services for a wide range of pieces such as connectors, contacts, boxes and accessories. Our plating services include: cadmium plating chemical nickel (medium and high phosphorous) copper, nickel, silver and gold plating passivation of stainless steel substitutes treatment plating to ROHS cadmium These treatments can be done in rack, barrel, vibratory bowl-feeder, reel to reel for stamped and formed contacts. To guarantee the best quality, we utilize different control methods: X-ray measurement for thickness binocular microscope for aspect salt spray chamber for testing corrosion chemical laboratory for the follow-up of the baths and the development of new processes. Our workshop is accredited by many OEMs such as MBDA, Aerazur, Safran... The plating is made in compliance with environmental norms, our factory is certified ISO 14001. 6 Design - Screw machining operations - Plating capabilities Amphenol PRODUCT DESIGNATION AND DERIVATED PRODUCTS In this catalog, Amphenol refers only on standard designations for the contacts usages. This page is a guide to help finding all the Amphenol compliant products behind the standard designation Design Screw machining operations Plating capabilities Product designation and derivated products MIL-DTL-38999 SERIES I Amphenol proprietary : LJT series (please refer catalog DOC-000031-ANG) Rack & Panel derivated product: RNJ series (please refer catalog E115) MIL-DTL-38999 SERIES II Amphenol proprietary : JT series (please refer catalog E 111 ) Quick release derivated product: SC39LP (please refer DOC-000637-ANG) MIL-DTL-38999 SERIES III / EN3645 Amphenol proprietary: TV / CTV series (please refer DOC-000035-ANG) Rack & Panel derivated product: RNJLP series (please refer catalog E124 ) Quick release derivated product: SC39 (please refer DOC-000637-ANG) For more information, please visit our website: www.38999-solutions.com Product designation and derivated products 7 Amphenol Signal Contacts Signal Contacts SIGNAL CONTACTS CRIMP CONTACTS MIL-DTL-38999 SERIES I, II,III / EN3645 / EN4165 Amphenol contacts are designed to meet and exceed SAE39029 and EN3155 standards. The following contacts are gold plating over suitable underplate. They withstand 500 and 1500 cycles. The 1500 cycles contacts are dedicated to MIL-DTL-38999 series III classes H and J. SAE39029 CONTACTS - US MIL STANDARD 500 CYCLES Color bands CONTACT PIN or SOCKET M39029/18-177 M39029/58-360 M39029/58-363 M39029/58-364 M39029/58-365 M39029/17-172 M39029/56-348 M39029/57-354 M39029/56-351 M39029/57-357 M39029/56-352 M39029/57-358 M39029/56-353 M39029/57-359 P S ! MILITARY Nb AMPHENOL Mating end Wire barrel P/N size size 23 22 20 16 12 23 22 22 20 20 16 16 12 12 22 22D 20 16 12 22 22D 22D 20 20 16 16 12 12 CONNECTOR Wire barrel MIL-DTL-38999 1st 2nd 3rd 900049 900004 900001 900000 900005 900048 900044 900014 900041 900011 900040 900010 900045 071315 SI S II X X X X X X X X X EN3645 EN4165 S III X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Contacts size 23 are dedicated to HD38999 Amphenol connectors. QU ALI FI PRO CATIO GRE N IN SS SAE39029 CONTACTS ENHANCED PERFORMANCES Color bands CONTACT PIN or SOCKET P S 8 MILITARY Nb AS39029/122-669 AS39029/122-670 AS39029/122-671 AS39029/122-672 AS39029/122-673 AS39029/122-674 AS39029/122-675 AS39029/121-662 AS39029/121-663 AS39029/121-664 AS39029/121-665 AS39029/121-666 AS39029/121-667 AS39029/121-668 AMPHENOL Mating end Wire barrel P/N size size 23 23 22 20 16 12 10 23 23 22 20 16 12 10 CONNECTOR Wire barrel 26 22 22D 20 16 12 10 26 22 22D 20 16 12 10 Signal Contacts / / 60088002 60088202 60088402 60088602 60023302 / / 60089002 60089202 60089402 60089602 60020802 MIL-DTL-38999 1st 2nd 3rd SI X X X X X X X X X X S II X X X X X S III X X X X X X X X X X X X X X EN3645 EN4165 X X X X X X X X X X X X Amphenol Signal Contacts Signal Contacts SIGNAL CONTACTS CRIMP CONTACTS MIL-DTL-38999 SERIES I, II,III / EN3645 / EN4165 SAE39029 CONTACTS 1500 CYCLES CONTACT PIN or SOCKET MILITARY Nb Mating end Wire barrel size size AMPHENOL P/N P S 22 20 16 12 22 20 16 12 22D 20 16 12 22D 20 16 12 MIL-DTL-38999 SI 1st M39029/107-620 M39029/107-621 M39029/107-622 M39029/107-623 M39029/106-614 M39029/106-615 M39029/106-616 M39029/106-617 CONNECTOR Color bands Wire barrel 2nd S II S III EN3645 3rd 900317 900318 900319 900320 900322 900323 900324 900325 X X X X X X X X X X X X X X X X SAE39029 WIRE BARREL RANGE AND NOMINAL TEST CURRENT (A) Wire barrel size 22 22D 20 16 12 12 14 23 17 16 18 13 10 Wire Size 20 22 5 5 7.5 5 7.5 24 3 3 3 26 2 2 28 1.5 1.5 COLOR BAND Orange Brown Violet Blue Green Black Yellow Red Gray White Signal Contacts 9 Signal Contacts Amphenol Signal Contacts SIGNAL CONTACTS CRIMP CONTACTS MIL-DTL-38999 SERIES I, II,III / EN3645 / EN4165 SAE 39029 CRIMPING TOOLS PIN or SOCKET MILITARY Nb M39029/18-177 M39029/58-360 P S PIN or SOCKET P S 10 CONTACT Mating end Wire barrel size size 23 22 22 22D Amphenol P/N 900049 900004 M39029/58-363 20 20 900001 M39029/58-364 M39029/58-365 M39029/17-172 M39029/56-348 M39029/57-354 16 12 23 22 22 16 12 22 22D 22D 900000 900005 900048 900044 900014 M39029/56-351 20 20 900041 M39029/57-357 20 20 900011 M39029/56-352 M39029/57-358 M39029/56-353 M39029/57-359 16 16 12 12 16 16 12 12 900040 900010 900045 071315 CONTACT Mating end Wire barrel size size AS39029/122-669 23 26 AS39029/122-670 23 22 Amphenol P/N AS39029/122-671 22 22D 60088002 AS39029/122-672 20 20 60088202 AS39029/122-673 16 16 60088402 AS39029/122-674 AS39029/122-675 AS39029/122-662 AS39029/122-663 12 10 23 23 12 10 26 22 60088602 60023302 / / AS39029/122-664 22 22D 60089002 AS39029/122-665 20 20 60089202 AS39029/122-666 16 16 60089402 AS39029/122-667 AS39029/122-668 12 10 12 10 60089602 60020802 MILITARY Nb Signal Contacts / / Crimping Tool Crimping Tool Positionner M22520/2-01 M22520/2-01 M22520/2-01 M22520/1-01 M22520/1-01 M22520/1-01 M22520/2-01 M22520/2-01 M22520/2-01 M22520/2-01 M22520/1-01 M22520/2-01 M22520/1-01 M22520/1-01 M22520/1-01 M22520/1-01 M22520/1-01 M22520/2-13 M22520/2-09 M22520/2-10 M22520/1-04 M22520/1-04 M22520/1-04 M22520/2-16 M22520/2-07 M22520/2-06 M22520/2-10 M22520/1-04 M22520/2-10 M22520/1-04 M22520/1-04 M22520/1-04 M22520/1-04 M22520/1-04 Crimping Tool QU ALI FI PRO CATIO GRE N IN SS Crimping Tool Positionner M22520/2-01 M22520/2-01 M22520/2-01 M22520/7-01 M22520/1-01 M22520/7-01 M22520/1-01 M22520/1-01 M22520/7-01 M22520/1-01 M22520/45-04 M22520/2-01 M22520/2-01 M22520/2-01 M22520/7-01 M22520/2-01 M22520/7-01 M22520/1-01 M22520/1-01 M22520/7-01 M22520/1-01 M22520/45-01 M22520/2-16 M22520/2-16 M22520/2-09 M22520/7-07 M22520/2-10 M22520/7-08 M22520/1-04 M22520/1-04 M22520/7-04 M22520/1-04 Basic tool M22520/2-16 M22520/2-16 M22520/2-07 M22520/7-05 M22520/2-10 M22520/7-08 M22520/1-04 M22520/1-04 M22520/7-04 M22520/1-04 Basic tool SIGNAL CONTACTS CRIMP CONTACTS MIL-DTL-38999 SERIES I, II,III / EN3645 / EN4165 Amphenol Signal Contacts Signal Contacts SAE 39029 CRIMPING TOOLS PIN or SOCKET P S CONTACT Mating end Wire barrel size size M39029/107-620 22 22D MILITARY Nb M39029/107-621 20 20 M39029/107-622 M39029/107-623 M39029/106-614 16 12 22 16 12 22D M39029/106-615 20 20 M39029/106-616 M39029/106-617 16 12 16 12 Crimping Tool Crimping Tool Positionner M22520/2-01 M22520/2-01 M22520/1-01 M22520/2-01 M22520/1-01 M22520/1-01 M22520/2-01 M22520/1-01 M22520/2-01 M22520/2-01 M22520/2-13 M22520/2-10 M22520/1-04 M22520/2-10 M22520/1-04 M22520/1-04 M22520/2-10 M22520/1-04 M22520/2-16 M22520/2-07 Signal Contacts 11 Signal Contacts Amphenol Signal Contacts SIGNAL CONTACTS CRIMP CONTACTS MIL-DTL-38999 SERIES I, II,III / EN3645 / EN4165 EN3155 CONTACTS - EUROPEAN STANDARD CONTACT CONNECTOR Color bands Wire barrel PIN or SOCKET EN3155 Mating end Wire barrel size size AMPHENOL P/N MIL-DTL-38999 1st P EN3155-008 EN3155-003 S EN3155-009 22 20 20 20 16 16 12 12 22 20 20 20 16 16 12 12 22 20 20 20 16 16 12 12 22 22 20 18 16 14 12 14 22 22 20 18 16 14 12 14 22 22 20 18 16 14 12 14 2st SI X X X X X X X X 60088001 60088101 60088201 60088301 60088401 60088501 60088601 60088701 60087001 60087101 60087201 60087301 60087401 60087501 60087601 60087701 60089001 60089101 60089201 60089301 60089401 60089501 60089601 60089701 X X X X X X X X S II X X X X X X X X X X X X X X X X EN3645 EN4165 S III X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X EN3155 WIRE BARREL RANGE AND NOMINAL TEST CURRENT (A) Wire barrel size 22 20 18 16 14 12 12 14 23 13 17 16 13 13 Wire Size 20 22 5 7.5 5 7.5 7.5 5 10 7.5 10 7.5 18 24 3 3 3 HOW TO BUILD EN3155 REFERENCE EN3155-008Y2020 12 EN3155-009X2020 Product Standard Product Standard Pin Contact Socket Contact Mating end size Mating end size Wire barrel size Wire barrel size Signal Contacts 26 2 28 SIGNAL CONTACTS CRIMP CONTACTS MIL-DTL-38999 SERIES I, II,III / EN3645 / EN4165 Amphenol Signal Contacts Signal Contacts EN3155 CRIMPING TOOLS PIN or SOCKET P EN3155 EN3155-008 EN3155-003 S EN3155-009 CONTACT Mating end Wire barrel size size 22 22 Amphenol P/N 60088001 20 22 60088101 20 20 60088201 20 18 60088301 16 16 12 12 22 16 14 12 14 22 60088401 60088501 60088601 60088701 60087001 20 22 60087101 20 20 60087201 20 18 60087301 16 16 12 12 22 16 14 12 14 22 60087401 60087501 60087601 60087701 60089001 20 22 60089101 20 20 60089201 20 18 60089301 16 16 12 12 16 14 12 14 60089401 60089501 60089601 60089701 Crimping Tool Crinping Tool POSITIONNER M22520/2-01 M22520/2-01 M22520/1-01 M22520/2-01 M22520/1-01 M22520/2-01 M22520/1-01 M22520/1-01 M22520/1-01 M22520/1-01 M22520/1-01 M22520/2-01 M22520/2-01 M22520/1-01 M22520/2-01 M22520/1-01 M22520/2-01 M22520/1-01 M22520/1-01 M22520/1-01 M22520/1-01 M22520/1-01 M22520/2-01 M22520/2-01 M22520/1-01 M22520/2-01 M22520/1-01 M22520/2-01 M22520/1-01 M22520/1-01 M22520/1-01 M22520/1-01 M22520/1-01 M22520/2-09 M22520/2-10 M22520/1-04 M22520/2-10 M22520/1-04 M22520/2-10 M22520/1-04 M22520/1-04 M22520/1-04 M22520/1-04 M22520/1-04 M22520/2-06 M22520/2-10 M22520/1-04 M22520/2-10 M22520/1-04 M22520/2-10 M22520/1-04 M22520/1-04 M22520/1-04 M22520/1-04 M22520/1-04 M22520/2-07 M22520/2-10 M22520/1-04 M22520/2-10 M22520/1-04 M22520/2-10 M22520/1-04 M22520/1-04 M22520/1-04 M22520/1-04 M22520/1-04 Signal Contacts 13 Signal Contacts Amphenol Signal Contacts SIGNAL CONTACTS SIGNAL CONTACTS PCB CONTACTS MIL-DTL-38999 SERIES I, III / EN3645 / EN4165 PIN or SOCKET Mating end size TYPE AMPHENOL P/N CI 900458 900245 900241 900240 900238 900459 900256 900251 900263 900403 23 22D 20 16 12 23 22D 20 16 12 P S TYPE AMPHENOL P/N LI 600867 922389 900243 900246 900282 600866 922390 900252 600526 Pin 900245, Socket 900256 MIL-DTL-38999 series I Connectors with PCB Contacts Sizes L2 Tailles L2 Pin Sizes SocketMale Femelle Pin Male Socket L2 L1 17 1,1 9-a2,1 a 24 0,7 - 1,78 a 161,2 -182,4 8,7 - 9,7 0,7 - 1,7 0,9 - 1,9 9 to 25 0,9 - 1,9 0,5 - 1,5 L1 9 a 25 1,6 - 2,6 13,7 - 14,6 13,5 - 14,4 1,6 - 2,6 L2 L1 1,4 2,4 13,5 --14,4 L2 Pin 12,3 - 13,2 8 a 18 0,4 - 1,620 a 22 0,4 - 1,6 1 - 2,2 13,6 - 14,6 8 to 22 1 - 2,2 12,1 - 13 5,1 - 5,9 0,2 - 1,4 24 4,9 - 5,7 L2 1,3 - 2,2 12,1 - 12,9 L2 L1 1,6 - 2,6 13,8 - 14,6 1,6 - 2,6 / 13,6 - 14,4 1,4 - 2,4 13,6 - 14,4 2,7 - 3,7 15,4 - 16,2 11,8 - 12,6 L2 2,7 - 3,7 1,1 - 2 15,2 - 16 11,6 - 12,4 2,5 - 3,5 0 - 0,7 8 a 22 24 11,9 - 12,7 1,1 - 2 L1 L2 L2 / 8 to 22 0,1 - 1 24 8 to 22 9 to 25 0 - 0,9 12,2 - 13 4,6 - 5,5 0 - 0,7 12 - 12,8 4,4 - 5,3 24 8 a 24 24 0,8 - 1,8 / 0,8 - 1,8 Signal Contacts 12,2 - 13 6,8 - 7,8 0,7 - 1,512 - 12,8 / 9,3 - 10,2 4,6 - 5,5 3,3 - 4,2 12 - 12,8 6,6 - 7,6 1-2 3,3 - 4,2 4,4 - 5,3 3,1 - 4 11,3 - 12,2 3,1 - 4 8 to 24 0,8 - 1,8 9 a 19 (-0,1) - 0,8 9,9 - 10,9 9,8 - 10,7 (-0,3) - 0,6 9 to 19 21 to 25 0,8 9,1 - 101,89,2 - 10,1 9 to 19 21 to 25 0,8 - 1,7 21 a 25- 13,2 12,3 21 a 25 9 a 19 12,3 - 13,2 12,8 - 13,6 1-2 11,3 - 12,2 9,3 - 10,2 9,4 - 10,3 13,6 - 14,4 12,1 - 13 1 - 1,9 0,8 - 1,8 12,6 - 13,4 13,4 - 14,2 1 - 1,9 9,1 - 10 9,2 - 10,1 0,8 - 1,7 9 to 19 21 to 25 12,8 - 13,6 13,6 - 14,4 1 - 1,9 12,6 - 13,4 13,4 - 14,2 0,8 - 1,7 0,8 - 1,7 9 to 19 21 to 25 21 a 25 11,5 - 12,4 11,5 - 12,4 12,3 - 13,2 12,3 - 13,2 6,8 - 7,8 / 6,8 - 7,8 11,3 - 12,2 12 - 12,8 6,6 - 7,6 9,4 - 10,3 9,1 - 9,9 1 - 1,9 12,1 - 13 10,1 - 11,1 10 - 10,9 21 a 25 1-2 11,5 - 12,4 11,5 - 12,4 6,8 - 7,8 L2 9,3 - 10,1 12,2 - 13 / - 1,5 4,2 0,7 - 5,1 9 a 19 0,8 - 1,8 24 1 - 2/ 4,2 - 5,1 9,8 - 10,7 13 to 25 (-0,3) - 0,6 0,8 - 1,7 9 a 25 9 a 19 12,2 - 13 1-2 0,8 - 1,6 0,8 - 1,7 9,9 - 10,9 9,1 - 9,9 0,9 - 1,7 0,9 - 1,7 9,8 - 10,7 0,8 - 1,7 1-2 / 4,5 - 5,3 L1 L1 L2 0 - 0,9 2,5 - 3,5 4,5 - 5,3 / 0,8 - 1,6 10 - 10,9 (-0,1) - 0,8 1 - 1,9 9,8 - 10,7 0,8 - 1,7 0,3 - 1,2 0,3 - 1,2 1,3 - 2,2 11,1 - 11,9 1 - 1,8 13 a 25 1 - 1,8 1 - 1,9 9,3 - 10,1 L1 11,1 - 11,9 11,9 - 12,7 15,2 - 16 11,6 - 12,4 L2 9,9 - 10,9 3,1 - 4,0 24 1,4 - 2,48 to0,1 -1 9 to 191,4 - 2,421 to 25 22 11,3 - 12,1 10,1 - 11,1 13,8 - 14,6 8 a 22 CTV 10 - 10,9 10 - 10,9 1 - 1,9 MIL-DTL-38999 series III / EN3645 composite 13 15 to 17 19 to 25 9 to 11 9 a 11 9,9 - 10,9 3,1 - 4,0 a 22 19 21 a 25- 12,9 8 a 22 24 L1 11,3 9-a12,1 12,1 15,4 - 16,2 11,8 -812,6 L1 9 to 11 13 a 25 3,3 - 4,215 a 17 1 19- 1,9 11,4 - 12,4 4,9 - 5,7 11,4 - 12,4 24 10,1 - 11,1 3,3 - 4,2 12,1 - 13 0,2 - 1,4 24 5,1 - 5,99 a 11 11,6 - 12,6 12,3 - 13,2 MIL-DTL-38999 series III / EN3645 11,6 - 12,6 TV 10,1 - 11,1 JT Tailles L1 Male 8 to 18 20 to 22 13,6 - 14,6 1,2 - 2,4 0,5 - 1,5 8,5 - 9,5 Tailles Socket Femelle 13,8 - 14,8 8,5 - 9,5 1,1 - 2,1 18 to 24 13,8 - 14,8 19 a 25 L1 L2 Sizes 14 SJT 13,7 - 14,6 L1 Tailles Sizes Femelle L1 L2 L2 8 to 16 8,7LJT- 9,7 L1 Femelle Socket Male Pin Connecteurs avec contact CI Contacts Male 900245, Femelle 900256 L1 19 to 25 9 to 17 MIL-DTL-38999 series II SJT 11,3 - 12,2 12,1 - 13 6,6 - 7,6 6,6 - 7,6 / 12,1 - 13 Amphenol Signal Contacts Signal Contacts SIGNAL CONTACTS THERMO COUPLE CONTACTS MIL-DTL-38999 SERIES I, II,III / EN3645 / EN4165 AMPHENOL thermocouples contacts are designed to keep the signal transmission of thermocouples wires. They meet or exceed SAE 39029 standards EN3155 BIN CODES Color bands CONTACT PIN or SOCKET P S ! AMPHENOL P/N 072502 072501 070586 070587 072500 072503 250711 250712 Wire barrel end MILITARY Nb Mating end size Wire barrel size M39029/87-471 M39029/87-472 M39029/87-475 M39029/87-476 M39029/87-479 M39029/87-480 M39029/88-484 M39029/88-483 M39029/88-488 M39029/88-487 M39029/88-492 M39029/88-491 22 22 20 20 16 16 22 22 20 20 16 16 22D 22D 20 20 16 16 22D 22D 20 20 16 16 CLASS 1st 2nd 3nd ALUMEL CHROMEL ALUMEL CHROMEL ALUMEL CHROMEL CHROMEL ALUMEL CHROMEL ALUMEL CHROMEL ALUMEL For other thermocouple class as Iron or Constantan, please consult us. PRINT CIRCUIT BOARD CONTACTS Amphenol Socapex can design specific Print Circuit Board pin contacts for thermocouple application. Please consult us. Amphenol Socapex has a wide range of thermo-couple contacts. Signal Contacts 15 Amphenol Power Contacts Power Contacts POWER CONTACTS SIZE 8 CONTACTS MIL-DTL-38999 SERIES III / EN3645 / EN4165 EN3155 COMPLIANT Amphenol has a large experience in power generation contact, and has developed some technologies dedicated to power in order to reduce heating, save space, as well as increasing the durability Pin or socket P Amphenol Mating end Wire barrel P/N size size EN3155-065 S ! EN3155 Color bands Contact EN3155-083 8 8 600863 8 10 600864 8 8 603160 8 10 600865 Wire barrel Crimping Tools 1st P 8 S See page 17 8 8 8 Piggy Back Grommet M300-BT with SP593 900471 900197 900198 900217 The contact 900198 is only compliant with 21-48 connector CONTACT PERFORMANCES MECHANICAL Endurance: 500 mating/unmating Shock & vibrations: As per EN3645 /MIL-DTL-38999 ELECTRICAL Max Current rating: 46A (8 8); 33A (8 10) ENVIRONMENTAL Temperature : -65C +200C Power Contacts 900472 900471 900472 Crimping Tool M300-BT is supplied by DMC Tools 16 900471 The standard EN3155-066 has been superseded by EN3155-083 Contact Pin or Amphenol socket Mating end Wire barrel P/N size size ! 2st Piggy Back Grommet Amphenol Power Contacts Power Contacts POWER CONTACTS CRIMPING TOOLS Pin or socket P S Crimping Tool Contact EN3155 Mating end Wire barrel size size EN3155-065 EN3155-083 Automatic tool M22520/23-01 Amphenol P/N Die Set 8 8 600863 8 10 600864 8 8 603160 8 10 600865 WA23-264DA Automatic tool Crimping tool M22520/23-01 Die Set Manual tool M300BT Locator WA23-447L Locator Selector SP593 4 SP593 3 SP593 4 SP593 3 Manual hand tool Locator Crimping tool M300BT Locator 38999 TYPE 21-48 - 4X60 AMPS CIRCULAR POWER CONNECTOR The Amphenol Socapex power connector 38999 type 21-48 provides 4 size 8 power contacts in a size 21 shell in accordance with the MIL-DTL-38999 Series I standard. This arrangement was originally developped for military applications. Due to the rigidity of the cables used, the front male insulator has been reinforced to maintain a perfect alignment of contacts during mating. A header is placed in the backshell to guide each wire and to guarantee tightness even when cables are bent. Available in TV-CTV (Mil-DTL-38999 Series III). Please refer to catalog E117 4X100A - CIRCULAR POWER This power connector from Amphenol LJT 25-1A was originally developped for military applications. Indeed, it is used in the conditioning of tanks. This connector has the particularity to provide 4 size 4 power contacts and 4 size 16 contacts in a size 25 shell in accordance with the MIL-C-38999 Series 1 standard. Available in TV-CTV Please refer to catalog E116 Power Contacts 17 Amphenol Power Contacts Power Contacts POWER CONTACTS SPECIFIC RANGE OF PRODUCTS AMPHENOL RADSOK TECHNOLOGY The RADSOK(R) High Amperage Electrical Terminal benefits the user from engineering, quality, and manufacturing viewpoints. RADSOK(R) technology is based upon a stamped and formed flat grid, twisted into a hyperbolic shape to provide secure and robust contact to the mating pin's contact surface. Most Pin and Socket technologies rely upon spring (compressive) properties of the contact elements,which may weaken over time. Unlike other Pin and Socket solutions, the RADSOK(R) also utilizes the tensile strength properties of the flat stamped, copper alloy grid to provide high normal forces with a large socket-to-pin conductive surface area. This design provides a correspondingly low voltage drop and low temperature rise. Other tensile design products use round wires (instead of flat bands) in the hyperbolic shape, this significantly reduces the contact surface between pin and socket. Proven by millions of parts in the field, a RADSOK(R) electrical connection is economical and extremely reliable, with zero reported failures in properly designed applications. RADSOK(R) technology benefits can be summarized as: * HIGH RELIABILITY Unique RADSOK(R) design and construction technology create an electrical contact interface that exceeds typical interconnect requirements. Applications in aerospace, medical, industrial, automotive, mining, offshore, and other harsh environments depend on high reliability of the Amphenol RADSOK(R) technology. * LOW CONTACT ENGAGEMENT/SEPARATION FORCES The hyperbolic lamella socket contact construction distributes normal forces over a high percentage of the mating pin surface. This creates a smooth, even engagement effort. This force distribution also contributes to excellent performance in vibration applications with resistance to typical fretting corrosion. * LOW CONTACT RESISTANCE The large interface area between the socket lamella and pin surface result in very low contact resistance, enabling the RADSOK(R) contacts' high current ratings compared to traditional power contact designs. * HIGH MATING CYCLE DURABILITY RADSOK(R) contacts with typical silver plating finishes have demonstrated survival of 20,000 mating cycles. Specialized plating and contact lubricants can extend cycle life to 200,000 matings or higher. Even with continuous exposure to harsh environmental abuse (salt, sand, and high humidity), RADSOK(R) contacts have been tested to maintain low contact resistance beyond 10,000 mating cycles. 18 Power Contacts NOTES Power Contacts Amphenol 19 Amphenol Coaxial Contacts Coaxial Contacts SHIELDED COAXIAL CONTACT These contacts are required for high frequency interconnection. High speed Coax contacts within a connector provide the shielding protection in order to eliminate interferences from outside electrical sources, and many cases the RF/Microwave performance needed in the circuitry of many applications. FEATURES AND BENEFITS Large crimping area assures low contact resistance and high tensile strength Back insulator provides closed entry for socket inner contact against axial loads Front insulator provides closed entry for socket inner contact Recessed inner contact is protected Outer contact has rugged wall section for durability MATERIALS AND FINISH Body: Copper alloy Finish: Gold over nickel on mating parts Insulators: High Performance Fluorocarbon TYPICAL COAXIAL CABLE Center conductor Insulation Braid Jacket ? GUIDELINE TO CHOOSE THE RIGHT COAXIAL CONTACT Choose the contact application : Standard Frequency, High Frequency or very high Frequency Standard Frequency: Non Impedance Matched Contacts ( VSWR: 1.5:1) High Frequency: Impedance Matched Contacts (VSWR: 1.2:1 +.04F (GHz) up to 3GHz) Very High Frequency: BMA / BMZ Interface contacts Check the cable diameter versus the contact size : Sometimes we can use a smaller contact Sometimes the wire is bigger than the contact ! 20 For more details, please refer contact and cable selection guides at page 56 Coaxial Contacts Coaxial Contacts Amphenol Coaxial Contacts SHIELDED COAXIAL CONTACT MIL-DTL-38999 SERIES II EN4165 SERIES INTERFACE AND QUALIFICATION : SAE AS39029 / 27,28,76,78 Contact Part Number Contact Size 16 Cable Pin Socket Proprietary Standard Proprietary Standard RG-178B/U, RG-196A/U 070575 M39029/76-425 070574 M39029/78-433 HAVEG 30-00761, 30-02024, 30-02033 TENSOLITE 24713/A955KK1, 26723/ A955KK1 900309 HAVEG 61-02051 900186 RG-174A/U, RG-188A/U, RG-161/U, RG-187A/U, RG-316/U, RG-179B/U, HAVEG 8100207, TIMES (HS-179) AA3248, TELEDYNE 11299, RAYCHEM 7528H1424 071094 12 Cable RG-174A/U, RG-188A/U, RG-161/U, RG-187A/U, RG-316/U, RG-179B/U, Haveg 8100207, Times (HS-179) AA3248, Teledyne 11299, Raychem 7528H1424 RG-180B/U, RG-195A/U, Raychem 9528A1318 Raychem 5022E5111 Inner contact Crimp ferrule M22520/2-01 with Positioner M22520/2-35 or with Daniels Positioner K532 M22520/4-01 with Positioner M22520/4-02 900310 900187 M39029/76-424 077987 M39029/78-432 Contact Part Number Contact Size Crimping Tools Pin Socket Crimping Tools Proprietary Standard Proprietary Standard 900340 M39029/28-211 900354 M39029/27-210 900286 M22520/2-01 with Positioner M22520/2-34 or with Daniels M39029/27-402 Positioner K323 900341 M39029/28-409 900424 900425 Raychem 9530A5314 900426 900427 Raychem 9527A1318 071954 900420 GORE GWN1159A 900428 900429 Coaxial Contacts Inner contact Crimp ferrule M22520/31-01 with Positioner M22520/31-02 or Daniels GS200 Tool with Positioner G2P330 21 Amphenol Coaxial Contacts Coaxial Contacts SHIELDED COAXIAL CONTACT MIL-DTL-38999 SERIES I, III / EN3645 Contact Part Number Contact Size 16 Cable Pin Socket Proprietary Standard Proprietary Standard RG-178B/U, RG-196A/U 070575 M39029/76-425 071965 M39029/77-429 HAVEG 30-00761, 30-02024, 30-02033 TENSOLITE 24713/A955KK1, 26723/ A955KK1 900309 900310 HAVEG 61-02051 900186 603247 RG-174A/U, RG-188A/U, RG-161/U, RG-187A/U, RG-316/U, RG-179B/U, HAVEG 8100207, TIMES (HS-179) AA3248, TELEDYNE 11299, Raychem 7528H1424 KX22A KX21A 071094 M39029/76-424 070248 900132 900142 900131 900141 M39029/77-428 Contact Part Number Contact Size 12 22 Cable Pin RG-174A/U, RG-188A/U, RG-161/U, RG-187A/U, RG-316/U, RG-179B/U, Haveg 8100207, Times (HS-179) AA3248, Teledyne 11299, Raychem 7528H1424 RG-180B/U, RG-195A/U, Raychem 9528A1318 Raychem 5022E5111 Socket Proprietary Standard Proprietary Standard 900340 M39029/28-211 900350 M39029/75-416 900341 M39029/28-409 900351 900424 900421 Raychem 9530A5314 900426 900422 Raychem 9527A1318 071954 900430 Gore GWN1159A, Nexans RG179-DT 900428 900075 Contacts CoaxialCoaxial Contacts Crimping Tools Inner contact Crimp ferrule M22520/2-01 with Positioner M22520/2-35 or with Daniels Positioner K532 M22520/4-01 with Positioner M22520/4-02 Crimping Tools Inner contact M22520/2-01 with Positioner M22520/2-34 or with M39029/75-417 Daniels Positioner K323 Crimp ferrule M22520/31-01 with Positioner M22520/31-02 or Daniels GS-200 Tool with Positioner G2P330 Amphenol Coaxial Contacts Coaxial Contacts SHIELDED COAXIAL CONTACT MIL-DTL-38999 SERIES I, III / EN3645 Contact Part Number Contact Size Cable Pin Proprietary RG-187A/U, RG-179B/U, RG-174A/U, RG-188A/U, RG-316/U, RG-161/U, Haveg 8100201, Times (HS-179)AA3248, Teledyne 11299 8 Crimping Tools Socket Standard 900135 Proprietary Standard Inner contact M22520/5-01 with die set M22520/5-03 (A) or M22520/508 (B) or M 900145 M22520/2-01 with Positioner M22520/2-31 or solder RG-142B/U, RG-223/U, SF-142 (solder inner conductor) 900136 900146 Haveg 51-03111, Tensolite 28895/2X1 600900 600910 RG-180B/U, RG-195A/U, Raychem 9528A1318 900130 M39029/60-367 Supersedes MS27536 900140 Crimp ferrule M39029/59-366 M22520/5-01 with die set M22520/5-05 (A) or M22520/519 (B) or M22520/1001 with Die Set M22520/10-07 (A) M22520/2-01 with Positioner M22520/2-31** or solder M22520/5-01 with die set M22520/5-41 (B) RD-316 Double Shield (M17/152-00001) 900137 900147 M22520/2-01 with Positioner M22520/2-31 M22520/5-01 with die set M22520/5-37 (B) or M22520/10-01 with die set M22520/10-15 (A) RG-400, ECS3C058A, ECS352001, ECS432101 900138 900148 M22520/2-01 with Positioner M22520/2-10 M22520/5-01 with die set M22520/5-45 (A) RG-58(M17/155-00001), M17/028-RG-058, RG303, Times LMR-195-UF 600901 600911 Solder 5021D1331-0 600902 600912 5M2869-001, ESC432101, BMS13-65 600903 600913 5022A1311-0 600904 600914 M22520/2-01 with Positioner M22520/2-31 Coaxial Contacts M22520/5-01 with die set M22520/5-05 (B) M22520/5-01 with die set M22520/5-05 (B) or M22520/10-01 with die set M22520/10-07 (B) 23 Amphenol Coaxial Contacts Coaxial Contacts IMPEDANCE MATCHED COAXIAL CONTACT AMPHENOL(R) MATCHED IMPEDANCE SIZE 12 COAXIAL CONTACTS FOR RF/MICROWAVE, HIGH FREQUENCY AND HIGH PERFORMANCE REQUIREMENTS The use of this contact is mandatory when he performance of standard Mil or EN contacts is not sufficient to achieve the level of signal transmission required. Below a large range of contacts with the correspondence of cable PN. MATCHED IMPEDANCE COAX CONTACT PERFORMANCE Contact impedance = 50 ohms nominal Frequency range = 0-3 GHz Operable at higher frequencies depending on cable selection. Consult Amphenol for details. Dielectric withstanding voltage (for a mated pair): At sea level = 1000 VRMS At 50, 000 ft. = 250 VRMS Insulation resistance: 5 gigaohms min. @ 25C VSWR: 1.20 + .04F (F in GHz) max. up to 3 GHz Insertion Loss: .11 fGHz dB max. Environmental Specifications: Thermal limits: -55 to 200C Mechanical Specifications: Mating: slide-on Mounting: conforms to M39029/102 & /103 envelope dimensions MIL-DTL-38999 SERIES I, II, III / EN3645 / EN4165 Contact Part Number Contact Size Cable Pin Proprietary 12 (Series II) 12 (Series III) Standard Proprietary Standard Crimping Tools Inner contact Crimp ferrule RG-316, T-Flex-405 900384 600750 MH992 with K1360 (5) RG178, Gore CXN 340 600907 600659 MH992 with K1360 (4) RD316, Filotex, ET124962, M17/152-00 001 900385 900395 M39029/102 MH992 with K1360 (5) type JN1088WT 600905 600915 PAN6422XQ 600906 600916 MH992 with K1360 (6) M22520 5-01 with M225205-03(a) MH992 with K1360 (5) RG178, GORE CXN 3403 600907 600917 MH992 with K1360 (4) SFT-316-TR 600908 600918 MH992 with K1360 (5) RG316 900384 900394 MH992 with K1360(5) MH992 is supplied by DMC Tools 24 Socket CoaxialContacts Contacts Coaxial M39029/103 type Coaxial Contacts Amphenol TYPICAL COAXIAL CONTACT INSTALLATION INSTRUCTIONS Picture Process Check Tools Strip the jacket slide the piggy back grommet and crimping ferule Do not damage the braid Blade Do not damage the inner conductor Trim shield strip cable core Coaxial Contacts SHIELDED COAXIAL CONTACT Blade Position nut on retainer as illustrated flare shield and slide nut and retainer assembly under the cable shield until retainer bottoms against braid Slide inner pin contact over cable center conductor crimp inner conductor The inner conductor shall be visible thru the inspection hole M22520/2-01 with positionner M22520/231 (5) Slide nut and retainer assembly forward until retainer flush with edge of cable core crimp shield crimp sleeve and observe a 0,25 and 1,3mm dimension Nut must be rotate freely after crimping sleeve M22520/5-01 with die M22520/5-37 (B) Expander tool bendix p/n 1110136 or equivalent rod bendinx p/n 11-10135 or equivalent Slide rear insulator using expander tool. slide tool over inner pin contact. Push rear insulator with push rod until it seats between retainer end and inner pin contact shoulder Snap rear insulator behind inner contact shoulder slide fron insulator until the inner contact flange Slide outer socket contact over inner pin assembly and insulator thread nut into rear of outer pin contact tighten nut until metal to metal ( 0,21 - 0,25N.m) Do not allow the cable to rotate while tightening the nut Coaxial Contacts 25 Amphenol Coaxial Contacts Coaxial Contacts SHIELDED COAXIAL CONTACT MIL-DTL-38999 SERIES I, III / EN3645 PRINT CIRCUIT BOARD CONTACTS Contact Part Number Contact Size 16 Tail Length Pin Socket Proprietary Proprietary CI 900184 900405 CI 900179 600748 Gold Tin X X Contact Part Number Contact Size 12 Tail Length Gold Pin Socket Proprietary Proprietary CI 900489 600749 X LI 900409 900412 X Tin IMPEDANCE MATCHED PCB COAXIAL CONTACT 900461 - SIZE 12 MATCHED IMPEDANCE COAX CONTACT PERFORMANCE : Contact impedance = 50 ohms nominal Frequency range = 0-3 GHz Operable at higher frequencies depending on cable selection. Consult Amphenol for details. Dielectric withstanding voltage (for a mated pair): At sea level = 1000 VRMS At 50, 000 ft. = 250 VRMS 26 Coaxial Contacts Insulation resistance: 5 gigaohms min. @ 25C VSWR: 1.20 + .04F (F in GHz) max. up to 3 GHz Insertion Loss: .11 fGHz dB max. Environmental Specifications: Thermal limits: -55C to 200C Amphenol Coaxial Contacts Pin 900184, Socket 900405 Connectors with Coax Contacts MIL-DTL-38999 series I Socket Pin Sizes L1 L2 L1 L2 9 to 17 8,3 - 9,5 0,7 - 1,9 Pin Socket (-0,1) - 1,1 9,6 - 10,8 0,6 - 1,8 0,6 - 1,7 9,3 - 10,5 0,2 - 1,3 13 to 25 9,7 - 10,9 9,6 - 10,7 0,6 - 1,8 9,2 - 10,4 0,2 - 1,4 9 to 11 (-0,5) - 0,7 9,3 - 10,5 0,2 - 1,4 9,2 - 10,3 (-0,9) - 0,3 9 to 19 21 to 25 L1 13,4 - 14,5 8,9 - 10 8,9 - 10,1 9 - 10,1 L2 1,2 - 2,5 0,6 - 1,8 L1 13 - 14,1 8,5 - 9,6 L2 0,8 - 2,1 0,2 - 1,4 L1 L2 L1 L2 L2 L1 L2 0,6 - 1,8 8,5 - 9,7 8,6 - 9,7 0,2 - 1,4 9 to 19 21 to 25 9 to 19 21 to 25 9 to 19 21 to 25 10,9 - 12 11,7 - 12,8 11,2 - 12,3 11,9 - 13 12,4 - 13,4 13,2 - 14,2 0,9 - 2,1 10,5 - 11,6 11,3 - 12,4 0,5 - 1,7 L1 Pin 15 to 17 19 to 25 9 to 25 Sizes Socket 13 9 to 25 Sizes Pin 0,3 - 1,5 0,3 - 1,5 9 to 11 9,7 - 10,9 7,9 - 9,1 Sizes Socket 19 to 25 MIL-DTL-38999 series III / EN3645 composite MIL-DTL-38999 series III / EN3645 / 0,6 - 1,8 10,8 - 11,9 0,6 - 1,8 11,5 - 12,6 0,2 - 1,4 12 - 13 12,8 - 13,8 0,2 - 1,4 9 to 19 21 to 25 11,2 - 12,3 11,9 - 13 6,4 - 7,7 10,8 - 11,9 Coaxial Contacts SHIELDED COAXIAL CONTACT / 11,5 - 12,6 6 - 7,3 Coaxial Contacts 27 Amphenol Coaxial Contacts Coaxial Contacts RF COAXIAL CONTACT MIL-DTL-38999 SERIES I, III / EN3645 FEATURES AND BENEFITS The HIGHEST frequency available on the market : up to 65 GHz The LARGEST range of size available on the market : 3 sizes - 8, 12 & 16 Designed for HARSH ENVIRONMENT : resistance to shocks and vibrations Unique float mount technology to allow consistant microwave performance APPLICATIONS Battlefield communications : high frequency applications Aerospace Telecom : radars, wireless networks (wifi, GSM) MATERIALS AND FINISH Body and Sleeve : Stainless steel per AMS-5640 Alloy UNS S30300 Type 1 Spring : Stainless steel per ASTM A313 Type 631 Ferrule : Brass per ASTM B16,Alloy UNS C36000 Rear Body & Contacts : Gold per ASTM B488 Type II,Code C, Class 1.27; over Nickel per AMS-QQ-N-290 Class 1 (60 inches); over Copper per MIL-C-14550 (10 inches) Passivated per AMS-2700, Type 2 Contact & Lock Ring : Beryllium copper per ASTM B196 Alloy UNS C17300, Td04 Insulator : PTFE per ASTM D1710,Type 1, Grade 1, Class B 28 Coaxial Contacts Coaxial Contacts Amphenol RF COAXIAL CONTACT Coaxial Contacts MIL-DTL-38999 SERIES I, III / EN3645 BMZ INTERFACE SPECIFICATIONS Impedance 50 Frequency Range DC - 40 GHz VSWR 1.07+.01 (freq. GHZ) Insertion Loss 0.06 (freq. GHz) Contacts size 8 BMZ Interface Contact Resistance (Max.) center conductor: outer conductor: outer to cable: 6.0 m 3.0 m 0.5 m Insulation Resistance (Min.) 10,000M DWV 1,000 VRMS RF Leakage-(80-freq. GHz) Corona Extinction Voltage 250 VRMS RF High Potential Voltage 500 VRMS BMA INTERFACE SPECIFICATIONS Impedance 50 Frequency Range DC - 26,5 GHz VSWR DC to 18 GHz 1.05 + .005f (GHz) 18 to 22 GHz 1.05 + .009f (GHz) Contacts size 8 BMA Interface Insertion Loss 0.3xf (freq. GHz) Contact Resistance (Max.) center conductor: outer conductor: 2.0 m 2.0 m Insulation Resistance (Min.) 5,000M DWV1,000 VRMS RF Leakage -(90-fGHz) Corona Extinction Voltage 670 VRMS RF High Potential Voltage 500 VRMS Coaxial Contacts 29 Amphenol Coaxial Contacts RF COAXIAL CONTACT Coaxial Contacts MIL-DTL-38999 SERIES I, III / EN3645 SMPM INTERFACE SPECIFICATIONS Impedance 50 Frequency Range DC - 65 GHz VSWR 1.1:1 DC to 26.5 GHz (typical) 1.3:1 26.5 to 65 GHz (typical) Insertion Loss (Adapters) .10 dB x f (where f = GHz) dB Insertion Loss (Cable Connectors) .12 dB x f (where f = GHz) dB Contact Resistance (Max.) center conductor: 6.0 m outer conductor:2.0 m Insulation Resistance (Min.) 5,000M DWV 325 VRMS RF Leakage -80 dB from DC to 3 GHz -65 dB from 3 to 65 GHz Contact Size Interface BMZ 8 BMA 30 Cable Frequency TFLEX-405 Contacts size 12 or 16 SMPM Interface Contact Part Number Piggyback Grommet Pin Socket 40 GHZ 600920 600925 TFLEX-405 18 GHZ 600921 600926 RG-400/ RG-142 12 GHZ 600922 600927 900471 TFLEX-402 18 GHZ 600923 600919 900472 TFLEX-405 26.5 GHZ 600600 600580 TFLEX-402 26.5 GHZ 600606 600581 900472 Pin Socket Piggyback Grommet 600924 600928 Contact Size Interface Cable Frequency 12 SMPM TFLEX-405 65 GHZ Contact Size Interface Cable Frequency 16 SMPM 0.047 DIA CABLE 65 GHZ Coaxial Contacts Contact Part Number Contact Part Number Pin Socket 600929 600930 Piggyback Grommet Amphenol Coaxial Contacts 75 OHMS COAXIAL CONTACT Coaxial Contacts MIL-DTL-38999 SERIES I, III / EN3645 FEATURES AND BENEFITS MIL-DTL-38999 / EN3645 CONNECTORS CRIMP AND PCB VERSION AVAILABLE MEET 3G-SDI VIDEO FORMAT MATERIALS AND FINISH SMPTE STANDARDS Sleeve : Stainless steel Contact & Ferrule : Copper Alloy Insulator: PTFE Rear Body & Contacts: Gold over nickel SMPTE: Society of Motion and Television Engineers SDI: Serial Digital Interface SD-SDI: Standard Definition SDI (SMPTE 259M) ED-SDI: Enhanced Definition SDI (SMPTE 344M) HD-SDI: High Definition SDI (SMPTE 292M) 3G-SDI: (SMPTE 424M) 75 OHMS SIZE 6 CONTACTS AND CONNECTORS Contact Size 6 Cable SMPTE SD-SDI HD-SDI Contact Part Number 3G-SDI PIN SOCKET Piggy Back Grommet 600757 603180 600762 600813 600715 600759 RG179B/U X X X DRAKA HD PRO 0.8/3.7 AF X X X BELDEN RG59 0.8/3.7 X X X GRUN 0.6/3.7 X X X SIZE 6 CONTACT CONNECTORS AND ARRANGEMENTS SHELL SIZE: 11 Please consult us SHELL SIZE: 19 Please consult us Coaxial Contacts 31 Amphenol Coaxial Contacts Coaxial Contacts 75 OHMS COAXIAL CONTACT MIL-DTL-38999 SERIES I, III / EN3645 75 OHMS SIZE 8 PERFORMANCE IMPEDANCE: 75Ohms FREQUENCY RANGE: 0 - 3GHz . Meet 3G-SDI standard (SMPTE 424M) Insulation resistance: 5G min @ 25C Dielectric Withstanding Voltage: 1300Vrms Rms @ sea level 250 VRms @ 50 000ft Contact Size 8 Cable SMPTE SD-SDI HD-SDI Contact Part Number 3G-SDI PIN SOCKET Piggy Back Grommet 600822 600841 603161 600830 600836 900472 RG179B/U X X X PIC V75268 X X X PIC V76261 X X X PIC 73263 X X X EMTEQ TFLX125-075-01 X X X 75 OHMS SIZE 8 PRINT CIRCUIT BOARD CONTACTS 32 Contact Size Tail Length 8 CI Coaxial Contacts SMPTE Contact Part Number SD-SDI HD-SDI 3G-SDI PIN SOCKET X X X 600889 600909 NOTES Coaxial Contacts Amphenol 33 Amphenol Concentric Twinax Contacts Concentric Twinax Contacts TWINAX CONTACTS Amphenol Twinax contacts were designed for use with twinax cable in data Bus systems. FEATURES AND BENEFITS Protection from magnetic interference Protection from electrostatic interference including nuclear electromagnetic pulse Meets parameters defined by MIL-STD-1553B Maintains shield integrity through a multi-pin circular connector and does not require contact polarization within the insert MATERIALS AND FINISH Body: Copper alloy Finish: Gold over nickel on mating parts Insulators: High Performance Fluorocarbon or PEEK TYPICAL TWINAXIAL CABLE Center conductor Insulation Braid Jacket ? DO YOU KNOW BUS1553 AND ARINC429 ? Amphenol size 8 concentric twinax are designed for use in MIL-STD-1553 data bus. MIL-STD-1553 is a military standard published by the United Department of Defense that defines the mechanical, electrical and functional characteristics of a serial data bus. Amphenol size 8 concentric twinax are designed for use in ARINC429 or DITS (Data Information Transfer System). ARINC429 is technical standard for the avionics data bus used commercial and transport aircraft. 34 Concentric Twinax Contacts Concentric Twinax Contacts Amphenol MIL-DTL-38999 SERIES I, III / EN3645 INTERFACE AND QUALIFICATION : SAE AS39029 / 90/91/113/114 Concentric Twinax Contacts TWINAX CONTACTS FEATURES AND BENEFITS 175C rated and meets performance levels of MIL-DTL-38999 series III connectors MIL-C-17/176-00002 cable termination Gold plated full crimp termination contacts qualified to M39029/90 & 91 TYPICAL ELECTRICAL PERFORMANCE: Voltage Rating: 500 Vrms max. @ sea level Contact Resistance: Center @ 1 Amp: Intermediate @ 1 Amp: Outer @ 12 Amps: Operating Frequency: Dielectric Withstanding Voltage: Center to Intermediate: Intermediate to Outer: 55 millivolts max. voltage drop @ 25C 55 millivolts max. voltage drop @ 25C 75 millivolts max. voltage drop @ 25C 0-20 MHz 1000 VAC Rms @ Sea Level 500 VAC Rms@ Sea Level Contacts Part Number Contact Size 8 PIN Cable SOCKET Comments Proprietary Standard Proprietary Standard M17/176-00002 074834 M39029/90-529 072453 M39029/91-530 Supplied with heat shrink seal M17/176-00002 600850 M39029/113-625 600851 M39029/114-628 Supplied with heat shrink seal Concentric Twinax Contacts 35 Amphenol Concentric Twinax Contacts Concentric Twinax Contacts TWINAX CONTACTS MIL-DTL-38999 SERIES I, III / EN3645 / EN4165 INTERFACE AND QUALIFICATION : EN3155-024 -025 & ABS2217 EN3155 QUALIFIED ABS22 17 COMPLIANT FEATURES AND BENEFITS 200C rated and meets performance levels of MIL-DTL-38999 series III connectors, EN3645 and EN4165 Many EN3375 cable termination Gold plated full crimp termination contacts qualified to EN3155024 -025 TYPICAL ELECTRICAL PERFORMANCE Voltage Rating: 500 Vrms max. @ sea level Contact Resistance: Center @ 1 Amp: Intermediate @ 1 Amp: Outer @ 12 Amps: Dielectric Withstanding Voltage: Center to Intermediate: Intermediate to Outer: 55 millivolts max. voltage drop @ 25C 55 millivolts max. voltage drop @ 25C 75 millivolts max. voltage drop @ 25C 1000 VAC Rms @ Sea Level 500 VAC Rms@ Sea Level Contact Part Number 36 Contact Size Cable 8 EN3375-003 KG24 EN3375-004 WJ24 EN3375-005 WV24 EN3375-009 W26 EN3375-006 XM24 EN3375-004 WJ24 Pin Socket Proprietary Standard Proprietary Standard 600611 EN3155-024M08AA 600614 EN3155-025F08AA 600612 EN3155-024M08BA 600615 EN3155-025F08BA 600613 EN3155-024M08CA 600616 EN3155-025F08CA 600854 ABS2217P01 600855 ABS2217S01 600856 ABS2217P02 600857 ABS2217S02 600858 ABS2217P03 600859 ABS2217S03 Concentric Twinax Contacts Crimping Tools Inner contact Intermediate Outer M22520/2-01 with Daniels positionner K880 M22520/5-01 with Daniels tools Y832 M22520/2-01 with Daniels positionner K1815 M22520/5-01 with Daniels tools Y832 Amphenol Concentric Twinax Contacts 1760 INTERFACE Contact Part Number Contact Size Cable Raychem 10614 EPD44692 EPD44695 8 ! PAN6421 Raychem 10613 Raychem 10612 M17/176-00002 EPD44690 EPD44691 Pin Crimping Tools Socket Proprietary Standard Proprietary Standard 076590 711-1760-101 076589 711-1760-201 076915 711-1760-102 076588 711-1760-202 077517 711-1760-104 077516 711-1760-204 Inner contact Intermediate Outer M22520/2-01 with Daniels positionner K880 M22520/5-01 with Daniels tools Y832 Concentric Twinax Contacts TWINAX CONTACTS Delivered without heat shrink boot or piggy back grommet TWINAX CONTACTS FOR ARINC600 ABS1600 AND ABS1607 ABS1600 ABS1607 QUALIFIED TYPICAL ELECTRICAL PERFORMANCE Voltage Rating: 500 Vrms max. @ sea level Contact Resistance: Center @ 1 Amp: Intermediate @ 1 Amp: Outer @ 12 Amps: Operating Frequency: Dielectric Withstanding Voltage: Center to Intermediate: Intermediate to Outer: 55 millivolts max. voltage drop @ 25C 55 millivolts max. voltage drop @ 25C 75 millivolts max. voltage drop @ 25C 0-20 MHz 1000 VAC Rms @ Sea Level 500 VAC Rms@ Sea Level Contact Part Number Contact Size 8 Cable EN3375-004 Pin Socket Proprietary Standard Proprietary Standard 140675 ABS1600M08A 140683 ABS1607F08A Concentric Twinax Contacts 37 Amphenol Concentric Twinax Contacts Concentric Twinax Contacts TYPICAL CONTACTS INSTALLATION INSTRUCTIONS FOR TWINAX CONTACTS PICTURE PROCESS CHECK TOOLS Do not damage the braid Blade Strip the jacket Slide the piggy back grommet and crimping ferule Open the braid over the crimping ferule The braid shall coiver equally the crimping ferule Strip the inner conductors Do not damage the inner conductors Blade Insert the white jacket inner conductor into the inner contact and crimp The inner conductor shall be visible thru the inspection hole M22520/2-01 with positionner Insert the crimp inner contact into the center hole and insert the blue inner conductor in the intermediate contact crimp the intermediate contact The inner conductor shall be visible thru the inspection hole M22520/5-01 with correct die Push the sub assembly into the outer contact when nice installed, cut the additional braid Do not damage the crimping ferule Blade Crimp the outer contact 38 Concentric Twinax Contacts M22520/5-01 with correct die Amphenol Concentric Twinax Contacts MIL-DTL-38999 SERIES III / EN3645 PRINT CIRCUIT BOARD CONTACTS AND SPECIFICS Pin 072265, Socket 600709 Connectors with Twinax Contacts Pin/Socket Sizes L1 L2 Pin/Socket Sizes Pin/Socket 9 to 11 13 10,4 - 11,6 15 to 17 19 to 25 10,2 -11,4 1,2 - 2,5 1,2 - 2,3 1,2 - 2,5 9 to 11 13 to 25 10,4 - 11,6 10,2 - 11,4 0,1 - 1,4 9 to 25 9 to 19 21 to 25 L1 9,5 - 10,6 9,5 - 10,7 9,6 - 10,8 L2 1,2 - 2,5 Sizes ? MIL-DTL-38999 series III / EN3645 composite MIL-DTL-38999 series III L1 L2 Concentric Twinax Contacts TWINAX CONTACTS 1,2 - 2,5 9 to 19 21 to 25 9 to 19 21 to 25 11,8 - 12,9 12,5 - 13,7 13 - 14,1 13,8 - 14,9 1,2 - 2,5 1,2 - 2,5 INFORMATION AMPHENOL CAN ALSO PROVIDE SPECIFIC AND CUSTOM TWINAX CONTACT SUCH AS: SIZE 10 and 12 SIZE 8 HOODED 90 TWINAX PLEASE CONSULT US Concentric Twinax Contacts 39 Amphenol Differential Twinax Contacts Differential Twinax Contacts DIFFERENTIAL TWINAX CONTACTS MIL-DTL-38999 SERIES III / EN3645 / EN4165 FEATURES AND BENEFITS Offer several advantages for high data transfer rates, low power consumptionand excellent EMI compatibility: Two strategically spaced inner contacts form two 100 or 150 Ohm matched impedance differential pairs Outer contact has rugged wall section for durability Available in size 8 crimp termination style Also available in size 8 with PC tails Requires modification of MIL-DTL-38999 connector to accommodate keyed contacts MATERIALS AND FINISH Body: Copper alloy Finish: Gold over nickel on mating parts Insulators: High Performance Fluorocarbon or PEEK TYPICAL TWINAXIAL CABLE Center conductor Insulation Braid Jacket 40 TYPICAL ELECTRICAL PERFORMANCE Bandwidth: Up to 1.25 GHz Data Rate: Exceeding 2.5 Gbps Voltage Rating: 500 Vrms max. @ sea level Dielectric Withstanding Voltage:1000 VAC rms between all inner contacts @ sea level 500 VAC rms between inner and outer contacts @ sea level Differential Twinax Contacts Differential Twinax Contacts Amphenol Differential Twinax Contacts DIFFERENTIAL TWINAX CONTACTS MIL-DTL-38999 SERIES III / EN3645 / EN4165 CRIMP CONTACTS Cable Pin Contact Part Number Impedance Socket (Ohms) Tensolite 24463/05099X-8(LD), Thermax MX 100-24, Tensolite 24463/9P025X-2(LD), Thermax 12814, ST5M1284-003 (98 Ohm), 26463/70460X- 2 (98 Ohm), PIC E10224, Fileca 2709-3, NF24T100-200C (Space), S280W502-1 900418 900419 GORE GSC-05-827300-00 Tensolite 26453/03184X-2(LD) Thermax 956-626Z 600931 600932 Tensolite 26453/03184X-2(LD), Thermax 956-626Z, GORE GSC-05-827300-00 ASNE08072003-09 600933 600934 23460/05114X-2(LD), PIC E1024 600935 600936 600937 600938 600939 600940 S280W502-6, Tensolite 24463/9P026X-2(LD) 600941 600942 AXON P509782 Tensolite 26453/03184X-2(LD) 600943 600945 600944 600946 Gore DXN 2125 600947 600948 Raychem 0026A0024, M17/176-00002 (77 Ohm) JSFY11-24, Tensolite 24463/03220T-2(LD), Thermax 956-1T200 Tensolite 26483/03071X-2(LD) 900294 900299 Tensolite 26483/03071X-2(LD) 600858 600899 100 Crimping Tools Inner contact Outer contact M22520/2-01 with M22520/5-01 with M22520/2-37 or die with Daniels set M22520/5-45 positionner (Location A) K709 150 Differential Twinax Contacts 41 Amphenol Quadrax Contacts QUADRAX CONTACTS Quadrax Contacts MIL-DTL-38999 SERIES III / EN3645 / EN4165 FEATURES AND BENEFITS Amphenol(R) Quadrax Contacts -Offer several advantages for high data transfer rates, low power consumption and excellent EMI compatibility: Four strategically spaced inner contacts form two 100 or 150 Ohm matched impedance differential pairs Outer contact has rugged wall section for durability Available in size 8 crimp termination style Also available in size 8 with PC tails Requires modification of MIL-DTL-38999 connector to accommodate keyed contacts MATERIALS AND FINISH Body: Copper alloy Finish: Gold over nickel on mating parts Insulators: High Performance Fluorocarbon or equivalent TYPICAL QUADRAX CABLE 1 2 3 4 1 - 4 Center conductor 2 - 4 Insulation 3 - Braid 4 - Jacket TYPICAL QUADRAX CABLE Bandwidth: Up to 1.25 GHz Data Rate: Exceeding 2.5 Gbps. Voltage Rating: 500 Vrms max. @ sea level Dielectric Withstanding Voltage: 1000 VAC rms between all inner contacts @ sea level 500 VAC rms between innerand outer contacts @ sea level 42 Quadrax Contacts Quadrax Contacts Amphenol QUADRAX CONTACTS Quadrax Contacts TV SERIES, MIL-DTL-38999 SERIES III / EN3645 / EN4165 CRIMP CONTACTS Contact Part Number Contact Size Cable Draka Fileca F-4703-3, F4704-4, Filotex ET 2PC236, Filotex ET2PF870, PIC Wire E50424, ABS0972, Tensolite 23450/04090X-4(LD) Draka Fileca F-4704-5, ABS1503 KD 24 8 Pin Socket 900496 900361 Crimping Tools Impedance Inner conductor (Ohms) Gauge Tensolite NF24Q100, NF24Q100-01, 24443/9P025X-4(LD), S280W502-4, 24443/03130X-4(LD), 24443/C20714X-4(LD), 24450/0120X-4(LD), NF24-2Q100, TYCO CECRWC18664, GORE GSC-0181869-01, 24443/03166X-4(LD), Thermax T956-4T200, Pic Wire E51424, Thermax MX100Q-24, NF24Q100-01-200C (Space), BMS13-72T03C04G024 900330 900338 Tensolite NF22Q100, NF22Q100-01, Thermax 956-5, GORE RCN 7688 900410 900411 600514 600516 26 600953 600954 24 600513 600515 26 Tensolite NF26Q100, NF26Q100-01, NF26-2Q100, PIC E51426, Wirenetics W-3714-379 S280W502-4/BMS1372T03C04G024 Draka Fileca F-4704-6, Gore RCN 8672 Ethernet (100 Mbps), 1000 Base-T Gigabit Ethernet (1 Gbps) 22 Gore RCN8513, JSFY18-3 Ethernet (100 Mbps), 1000 Base-T Gigabit Ethernet (1 Gbps) 22 Tensolite NF24Q100, NF24Q100-01 for 2.5 Gbps applications 600951 600952 Gore 8647 600955 600956 USB2 (28433/02171LX-4) 600987 600958 Tensolite 24450/03089X-4(LD) Gore RCN8647 050998 050999 JSFY02-1, JSFY18 600959 600960 Gore RCN8487, JSFY18 Tensolite 26473/02006X-4(LD)/Gore RCN8328 (not for new designs, use 21-033450/1 series) 600961 600962 900327 900337 Inner contact Outer contact Ethernet, 1000 Base-T Gigabit Ethernet 24 100 Electrical Protocol M22520/2-01 with Positioner M22520/2-37 or with Daniels Positioner K709 M22520/5-01 with Die Set M22520/5-45 (Location A) Serial FPDP Applications (2.5 Gbps) (Typical app run at 150 Ohms) HDMI 1.3 24 24 90 USB2.0 (480 Mbps) IEEE 1394B Firewire 24 110 IEEE 1394B Firewire IEEE 1394B Firewire 150 26 EN3155-074 AND -075 CRIMP CONTACTS Contact Size 8 EN3155 QUALIFIED Contact Part Number Cable Pin Proprietary Standard 600963 EN3155-074M8A Socket Proprietary Standard 600964 Crimping Tools Impedance Inner conductor (Ohms) Gauge EN3155-075F08A ABS1503KD24 100 603085 EN3155-074M08 603086 EN3155-075F08 24 Electrical Protocol Inner contact Outer contact M22520/2-01 with Positioner Ethernet, 1000 Base-T M22520/2-37 Gigabit Ethernet or with Daniels Positioner K709 Quadrax Contacts M22520/5-01 with Die Set M22520/5-45 (Location B) 43 Amphenol Quadrax Contacts Quadrax Contacts QUADRAX CONTACTS FOR SUBMINIATURE TYPICAL CONTACTS INSTALLATION INSTRUCTIONS FOR QUADRAX CONTACTS Picture Process Check Tools Do not damage the braid Blade Open the braid over the crimping ferule The braid shall coiver equally the crimping ferule Blade (To Trim Excess Braid) Strip the inner conductors Do not damage the inner conductors Blade Crimp the inner contacts The inner conductor shall be visible thru the inspection hole M22520/2-01 with positionner M22520/2-37 Install the rear insulator and respect the circular location for each individual contact The contact location shall respect circular location Slide the front insulator over the contact by the front The keyway orientation shall meet the key way in outer contact Strip the jacket Slide the piggy back grommet and crimping ferule Crimp the outer contact 44 Quadrax Contacts M22520/5-01 with M22520/5-45(A) Quadrax Contacts Amphenol QUADRAX CONTACTS FOR SUBMINIATURE Quadrax Contacts MIL-DTL-38999 SERIES III / EN3645 PRINT CIRCUIT BOARD CONTACTS Contact Size 8 Release Type Rear Rear Contact Part Number PIN SOCKET CI 900210 600520 LI 600512 600519 Impedance (Ohms) 100 Pin 900210, Socket 600520 Connectors with Quadrax Contacts Pin/Socket Sizes L1 L2 Pin/Socket Sizes 9 to 11 13 10,4 - 11,6 15 to 17 19 to 25 10,2 -11,4 1,2 - 2,5 1,2 - 2,3 9 to 11 13 to 25 10,4 - 11,6 10,2 - 11,4 1,2 - 2,5 0,1 - 1,4 9 to 25 9 to 19 21 to 25 L1 9,5 - 10,6 9,5 - 10,7 9,6 - 10,8 L2 1,2 - 2,5 Sizes Pin/Socket MIL-DTL-38999 series III / EN3645 composite MIL-DTL-38999 series III / EN3645 L1 L2 1,2 - 2,5 9 to 19 21 to 25 9 to 19 21 to 25 11,8 - 12,9 12,5 - 13,7 13 - 14,1 13,8 - 14,9 1,2 - 2,5 1,2 - 2,5 Quadrax Contacts 45 Amphenol Quadrax Contacts QUADRAX CONTACTS Quadrax Contacts ARINC600, EN3545 CRIMP CONTACTS Contact Size Contact Part Number Cable Pin ABS0972 ABS1503KD24 8 603113 Tensolite NF24Q100, NF24Q100-01, 24443/9P025X-4(LD), S280W502-4, 24443/03130X-4(LD), 24443/0120X-4(LD), NF24-2Q100, TYCO CECRWC-18664, GORE GSC-01-81869-01, 24443/03166X-4(LD), Thermax T956-4T200, Pic Wire E51424, Thermax MX100Q-24, NF24Q100 01-200C (Space), BMS13 72T03C04G024 Socket Impedance (Ohms) Electrical Protocol Crimping Tools Inner contact Outer contact M22520/5-01 with Die set M22520/545 (Location A) 603116 100 603210 Inner conductor Gauge Ethernet, 1000 Base-T, Gigabit Ethernet, ARINC664 24 603209 M22520/2-01 with positionner K709 M22520/5-01 with Die set M22520/545 (Location B) PRINT CIRCUIT BOARD CONTACTS Contact Size Release Front 8 Rear Contact Part Number Pin Socket Impedance (Ohms) 603228 603177 Connector ARINC600 EN3545 603229 100 ? DO YOU KNOW AFDX AND ARINC664 ? Amphenol size 8 quadrax contacts are designed for use in ARINC664p7 or AFDX network. AFDX (Avionics Full Duplex Switched Ethernet) and ARINC 664 are a data network based on ethernet technology. AFDX is patented by AIRBUS. 46 Quadrax Contacts Quadrax Contacts Amphenol NOTES 47 Amphenol Split Pair Quadrax Contacts Split Pair Quadrax Contacts SPLIT PAIR QUADRAX CONTACTS MIL-DTL-38999 SERIES III / EN3645 / EN4165 FEATURES AND BENEFITS Overall higher bandwidth than standard CAT5E quadrax Enhanced crosstalk performance (compared to standard quadrax) due to compatibility with shielded twisted pair of cables Can be used for a variety of high speed applications beyond current quadrax design** Four strategically spaced inner contacts form two 100 Ohm matched impedance differential pairs Outer contact has rugged wall section for durability Available in size 8 crimp termination style Also available in size 8 PC tails Can be installed into existing quadrax contact connector cavities Requires modification of MIL-DTL-38999 connector to accommodate keyed contacts APPLICATION For use with, but not limited to, the following electrical protocols : 10/100/1000/10GBASE-T Ethernet DVI USB 2.0, 3.0 Serial Rapid IO (up to 3.125 Gbps) PCI-Express 2.0 HDMI 1.3a SATA 2.0 (up to 3 GHz) CRIMP CONTACTS Contact Part Number Contact Size 8 Cable Thermax 1536-224 Crimping Tools Pin Socket Inner conductor Gauge Inner contact Outer contact 050742 050741 24 DANIELS M22520/2-01 with positioner K1777 DANIELS M22520/5-01 with die set Y1999 or M22520/5-45 PRINT CIRCUIT BOARD CONTACTS Contact Part Number Contact Size 8 Release Type Socket Rear CI 603250 600742 Rear LI 603251 603252 ** For stick out, please refer to p45 48 Pin Split Pair Quadrax Contacts Impedance (Ohms) 100 Amphenol Com Contacts HARSH ENVIRONMENT 10GB ETHERNET MICRO CONNECTORS Com Series is a new range of connectors designed to address the latest trends of the industry : miniaturization and high speed, with the highest resistance for use in the harshest environments. Com-10Gb + is the first product of this new range. Com Contacts COM-10GB + MAIN FEATURES 10Gb+ exceeds 10Gb/s Ethernet following IEEE 802.3an-2006 : 10GBase-T Cat.6A connector according to TIA568C.2 and ISO/IEC11801 norms Environmental testing based on MIL-DTL-38999 series III military specifications Miniature : 15 mm(.59) max external diameter FEATURES AND BENEFITS 4 pairs totally insulated throughout the connector minimum cross-talk between the four pairs Machined & gold plated Solder and Crimp contacts design & performance according to the innercontact of M39029/77-429#16 M39029/76-425#16 38999 contact Patent pending special interfacial shapes minimum perturbation at the interface of each pair Solder contact : max AWG24 Crimp contact : AWG 24 to 26 Thread coupling mechanism 2000 mating cycles & high vibration resistance IP68 sealing mated and unmated for receptacles Machined Brass shells and RoHS compliant plating shell to shell continuity and 500h salt Spray resistance 1500 Vrms Dielectric Withstanding voltage Temperature range : - 55C / + 125C HOW TO ORDER Female In-line receptacles UCOM - 10G+ L S B G A Female receptacles UCOM - 10G+ Shell L: in line receptacle (push pull or thread) Shell R: receptacle (push pull or thread) Contacts termination C: crimp S: solder Contacts termination P: PCB S: solder C: crimp Shell plating B: black nickel G: olive drab cadmium U: unplated brass P B Shell plating B: black nickel G: olive drab cadmium U: unplated brass Backshell type G: gland B: band Cordsets Cable diameter (for gland backshell only) A: for cable diam 7.5mm B: to be defined Male plugs R UCOM - 10G+ Shell P: plug Mating (for plugs only) T: thread P: push-pull Contacts termination C: crimp S: solder Shell plating B: black nickel G: olive drab cadmium U: unplated brass Backshell type G: gland B: band Cable diameter (for gland backshell only) A: for cable diam 7.5mm B: to be defined P T C B G A UCOM - 10G+ C T C B 015 Shell C: Com plug - Com plug cordset D: Com plug - RJ45 Cat6A plug cordset E: Com panel mount receptacle - RJ45 Cat6A plug cordset F: Com plug - Com inline receptacle cordset Open versions: G: Com plug - no connector at the end H: Com panel mount receptacle - no connector at the end J: Com inline receptacle - no connector at the end Mating (for plugs only) T: thread Contacts termination C: crimp S: solder Shell plating B: black nickel G: olive drab cadmium U: unplated brass Total length - For other lengths, please consult us. 002: 20 cm [7.87] 005: 50 cm [19.68] 010: 1.0 m [39.37] 015: 1.5 m [59.05] 020: 2.0 m [78.74] 050: 5.0 m [196.85] 100: 10.0 m [393.70] For more information on Com series, thanks to consult our dedicated datasheet Com Contacts 49 Amphenol High-speed cordsets High-speed cordsets HIGH-SPEED CORDSETS Thanks to our large contacts portfolio and expertise on major high speed protocols, Amphenol Socapex is now offering a capability of high-speed cordsets design and manufacturing. All cordsets are fully tested with test such as DWV, resistance and continuity. Other tests could be performed on demand. 38999 connectors to RJ45 USB3 to SPLIT-PAIR QUADRAX QUADRAX TO DIFFERENTIAL TWINAX ASSEMBLY SHOP A dedicated 400m workshop and team focus on harnesses and cordsets manufacturing. Technical and manufacturing supports are available in France to help you on your definition. 50 High-speed cordsets Optical Termini Amphenol M29504/4 & /5 FEATURES AND BENEFITS Precision fiber optic ceramic ferrules Pre-radius ferrule design Precision "press fit" stainless steel design Accurate ferrule alignment system Size 16 design (MIL-DTL-38999 compatible) Low insertion loss and back refection Designed and manufactured to MIL-PRF-29504/ 4 and /5 specifications Optical Contacts FIBER OPTIC TERMINI BENEFITS Solid reliable connectivity through a wide range of harsh environmental conditions Compatible with all qualified MIL-DTL-38999, Series III connectors. Fast termination and polish time Reliable, repeatable and durable connections Easy to clean PRODUCT SPECIFICATIONS Solid reliable connectivity through a wide range of harsh environmental conditions Compatible with all qualified MIL-DTL-38999, Series III connectors. Fast termination and polish time Reliable, repeatable and durable connections Easy to clean Specification Back Reflection Insertion Loss Measurement/Detail Better than -40 dB - PC polish Better than -50 dB - enhanced PC polish 0.45 typical (measured with 62.5/ 125 mm fiber @1310nm) Operating Temperature -65C to +150C Temperature Life +150C for 1000 hours Vibration 40 G random Mechanical Shock 500 G Mating Durability 500 cycles Salt Spray 500 hours Cable Retention Force 25 lbs (dependent on cable construction) Optical Termini 51 Amphenol Optical Termini M29504/4 & /5 Optical Contacts FIBER OPTIC TERMINI ABOUT THE M29504 Amphenol Fiber Systems International's (AFSI) M29504 /4 & /5 Style Fiber optic termini, the M29K1000 and M29L1000 series, provide superior optical and mechanical performance. Designed to fit into MIL-DTL-38999 Series III, pin size 16 connectors, this low-cost, high-precision terminus family is ideal for harsh environment fiber optic interconnections. Available for single mode and multimode applications these termini conform to the rigorous conditions of the MIL-PRF-29504B specification. The M29K1000 and M29L1000 series termini utilize the highest quality Zirconia ceramic ferrules and split alignment sleeves available. AFSI's tight-tolerance ferrules are optimized for low insertion loss, low back reflection and exceptional durability. All ferrules are available in standard and ultra polished end faces for those tight optical budget applications. In addition, epoxy removal and polishing times are minimized by the ferrule's pre-domed design feature. The M29L1000's Zirconia split alignment sleeve design ensures accurate physical contact, fiber-tofiber alignment and guarantees the highest performing connector of its kind for use in a variety of demanding environmental conditions. The M29K1000 and M29L1000 series fiber optic termination system offers precise, superior and reliable connections over repeated connector mating cycles and through a wide range of harsh environmental conditions. M29504/4 FIBER SIZE TABLE AFSI Pin Part Number M29K2000 M29K1001 M29K1000 M29K3000 M29K3001 M29K5000 M29K5001 M29K6000 M29K6001 M29K8000 M29K8050 M29K9000 Fiber Size Core/Cladding A Diam. (Microns) Reference Only M29504 /4-XXXX 9/125 50/125 & 62.5/125 50/125 & 62.5/125 100/140 100/140 62.5/125/155 (Polyimide) 62.5/125/155 (Polyimide) 100/140/172 (Polyimide) 100/140/172 (Polyimide) 200/233 200/280 400/440 126 126 127 142 144 156 157 173 175 236 286 448 M29504/4-4209 M29504/4-4210 M29504/4-4040 M29504/4-4043 M29504/4-4044 M29504/4-4211 M29504/4-4212 M29504/4-4087 M29504/4-4213 M29504/4-4214 M29504/4-4215 M29504/4-4216 Fiber Size Core/Cladding A Diam. (Microns) Reference Only M29504 /4-XXXX 9/125 50/125 & 62.5/125 50/125 & 62.5/125 100/140 100/140 62.5/125/155 (Polyimide) 62.5/125/155 (Polyimide) 100/140/172 (Polyimide) 100/140/172 (Polyimide) 200/233 200/280 400/440 126 126 127 142 144 156 157 173 175 236 286 448 M29504/5-4238 M29504/5-4239 M29504/5-4046 M29504/5-4049 M29504/5-4050 M29504/5-4240 M29504/5-4241 M29504/5-4088 M29504/5-4242 M29504/5-4243 M29504/5-4244 M29504/5-4245 M29504/5 FIBER SIZE TABLE AFSI Pin Part Number M29L2000 M29L1001 M29L1000 M29L3000 M29L3001 M29L5000 M29L5001 M29L6000 M29L6001 M29L8000 M29L8050 M29L9000 52 Optical Termini Optical Termini Amphenol LUX-BEAM(R) ABOUT LUX-BEAM(R) The new requirements for Avionics and Field communication systems demand for always higher amount of data, HD video transmission and higher bandwidth to be transmitted. Fiber optic technology is the technology of choice for those requirements. Lux-beam size 16 Optical Contacts SINGLE EXPANDED BEAM TERMINI With over 20 years of production of fiber optics expanded beam solutions, Amphenol introduces the LUX-BEAMTM Single Expanded beam termini. A solution to upgrade the optical physical contact technology to an optical contacless technology. LUX-BEAMTM is easy to clean, less sensitive to pollution by dust or debris. The contactless coupling of LUX-BEAMTM is not subject to degradation of performances resulting from friction of optical surfaces as it usual is on traditional butt joint termini. With its patented pin to socket realignment feature, LUX-BEAMTM is compatible with connectors from different suppliers and provides an efficient adjustment to tolerances during mating. Per design, LUX-BEAMTM is as easy to install. FEATURES AND BENEFITS Expanded Beam technology Surface expanded bundle >140X Reduced sensitivity to dust No degradation of the optical face Easy cleaning Low maintenance Expanded Beam Technology Fiber S= Initial Expanded Beam >140xS Fiber S= Initial Compatibility Cavity #16 MIL-DTL-38999 series III TV/CTV, EN3645 EN 4165 (SIM) Lens Lens Other benefits technology Easy installation with standard tools Possibility to mix with Electrical contact for Hybrid solutions Optical Termini 53 Amphenol Optical Termini LUX-BEAM(R) TECHNICAL DATA Optical Contacts SPECIFICATION MEASUREMENT DETAILS STANDARD METHOD 1.5dB max multimode, 850nm 1.5dB max multimode, 1300nm 500 cycles MIL-PRF-29504D TIA-455-34 MIL-DTL-38999 TIA-455-21 125C 1000H MIL-PRF-29504D TIA-455-04 Storage temperature -40C / +85C MIL-PRF-29504D Temperature cycling 5 cycles -40C +70C MIL-DTL-38999 TIA-455-03 Thermal shock 5 cycles -55C +125C MIL-PRF-29504D TIA-455-34 Humidity 24h at 50C max 33% hum 240H at 40C 90% RH MIL-DTL-38999 TIA-455-05 MIL-PRF-29504D TIA-455-16 Insertion loss Mating durability Operating temperature, temperature life Salt spray Insertion and removal force 48H Connectors mated Method B: Figure 2, Table 1, level J (1g2/Hz) Duration: 8h / axe - 2 axes longitudinal and perpendicular direction. Duration of micro-discontinuity : < 1s IL max 2dB. Method A, severity 100 Number of shocks: 1 each way for each of the 2 directions (6 shocks in all). Duration of micro-discontinuity : < 1s max 22 pounds Maintenance aging 10 insertions / removal cycles Vibration Shock EN2591-6403 EN2591-6402 MIL-PRF-29504D 3.6.9 MIL-PRF-29504D 3.6.13 HOW TO ORDER Designation Series LXB : LUX-BEAM, Single expanded beam optical termini Cavity size 16 : size 16 for 38999 series III Type of termini P : Pin termini S2 : Socket termini for series II S3 : socket termini for seriess III Wavelength A : optimised for wavelength 850nm (Multimode) B : optimised for wavelength 1300nm (Multimode) C : optimised for wavelength 850nm & 1300nm (Multimode) Cable 18X : for cable 1.8mm 54 Optical Termini LXB LXB 16 16 P S2 A C 18X 18X Optical Termini Amphenol LUX-BEAM(R) CABLE ASSEMBLIES WITH LUX-BEAMTM TO OTHER TERMINI Designation LXB 16 P A 1 D 1 L 0020 ST2 Type of Termini LXB: LUX-BEAMTM, Single expanded beam optical termini 1 D 0 M Optical Contacts HOW TO ORDER CABLE ASSEMBLIES WITH LUX-BEAMTM Cavity size 16: size 16 for 38999 series III Type of termini P : pin termini S2 : socket termini for series II S3 : socket termini for series III Wavelength A: optimised for wavelength 850nm (Multimode) B: optimised for wavelength 1300nm (Multimode) C : optimised for wavelength 850nm & 1300nm (Multimode) Termination type 1: PC Ceramic Boot form D: straight boot Type of fiber 1: 50/125 Multimode 2: 62.5/125 Multimode Type of cable L: Simplex cable with buffer 900m and outer jacket dia. 1.8mm Length XXXX: length in m for L 10m, ex 0020 for L=20 meters X.XX: length in m for L < 10m, ex 5.00 for L=5.0 meters Type of Termini XXX: pigtail ST2: connector ST2 954: connector SC simplex LCS: connector LC simplex ELU: connector ARINC 801 optical termini Termination type 1: PC Ceramic Boot form D: straight boot Protective Cap O: standard protective cap Marking : standard marking MX: specific marking Optical Termini 55 Amphenol Optical Termini LUMIERE Optical Contacts FIBER OPTIC TERMINI ABOUT THE LUMIERE Amphenol Fiber Systems International (AFSI) offers the Lumiere fiber optic terminus for commercial airframe, avionics and aerospace applications. AFSI's Lumiere termini are a direct replacement for ELIO(R) termini and are compatible with existing ELIO(R) connectors. This fiber optic contact utilizes a 2.5mm diameter field-proven ceramic ST type ferrule which can be inserted into a size #16 cavity. The terminus is hermaphroditic allowing the use of the same contact on the receptacle or plug. In addition, the contact is available in both multi-mode and single mode versions and an anti-rotation feature allows PC, UPC and APC polishes. Because the Lumiere uses a standard ST type ferrule, well known procedures and readily available tools can be used for termination. Long and short boot versions are available to support multiple connector types. Amphenol also manufactures a full line of EN 4531 rectangular and cylindrical connectors to house the Lumiere termini. FEATURES AND BENEFITS Hermaphroditic style allows one contact type Standard 2.5mm ST type ferrule interface allows the use of standard termination procedures and readily available tools Simple access to optical termini facilitates cleaning Options available for single mode and multimode fiber Pull Proof option allows the use of the terminus in a connector without a backshell Supports both tight or loose structure cable OPTICAL PERFORMANCE Typical IL: 0.3dB SM, 0.2dB MM @ 1300nm Typical Return Loss: -30dB SM and MM @ 1300nm 56 Part Number Description AOT 4532-1 Lumiere-S, Short Boot AOT 4531-2 Lumiere-L, Long Boot Optical Termini Optical Termini Amphenol ARINC 801 Optical Contacts FIBER OPTIC TERMINI ABOUT ARINC 801 TERMINI Amphenol Fiber Systems International (AFSI) offers the fully-compliant ARINC 801 fiber optic terminus for aerospace applications. The AFSI ARINC 801 uses a standard 1.25 mm ferrule and sleeve and can be terminated with standard LC termination procedures. The terminus can be inserted, or removed, from the connector with a standard size 16 removal tool. The terminus is available in both multimode and single mode versions. The fiber optic contact provides low insertion loss (0.3 dB max) and backreflection (-50 dB). In addition to the standard PC end-face option, AFSI's ARINC 801 is offered with an APC end-face for those applications requiring lower backreflection. The terminus is highly flexible and is used primarily in ARINC 801, 600, 404, 781 and EPXA/B multichannel connectors. The fiber optic contact is offered in an optional pull-proof (allows the use of the contact in a connector without a strain-relief backshell) configuration and an optical disconnect style for tight jacket cable. FEATURES AND BENEFITS Flexible design for use in multiple connector types Genderless terminus allows one contact type Standard 1.25 mm LC ferrule interface allows the use of standard termination procedures and widely available tools Options available for single mode and multimode fiber in PC or APC polishes Pull-proof option allows the use of the terminus in a connector without a backshell Works with tight or loose structure cable All stainless steel option available Specification Insertion Loss Operating Temperature Measurement/Detail 0.3 dBmax (multimode) 0.5 dBmax (singlemode) -55 C to +85 C Connector Format ARINC 600, 404, 781&801;MIL-DTL-82527 type; MIL-DTL-38999 Mating 100 mate/demate cycles Cable OD Supported 1.55 mm to 2.2 mm Optical Termini 57 Amphenol Accessories Accessories Appendix ACCESSORIES Amphenol provides a full range of accessories as: Sealing plugs: to be mounted behind the crimp contacts Dummy contacts: to be mounted instead of the contacts Piggy Back Grommets: To insure back contact sealing when using size 8 power, coax, twinax or quadrax. Those piggy back grommets are only compliant with tower grommet style SEALING PLUGS Contact size Proprietary No Military No 8 power 900024 - 12 900023 MS27488-12-2 16 900020 MS27488-16-2 20 22D 23 900021 900022 900022 MS27488-20-2 MS27488-22-2 MS27488-22-2 Dummy contact material Proprietary No 4 White plastic 900329 8 Green plastic 900488 8 Brass + gold finish 900183 8 12 12 16 16 20 White plastic (recommended) Brass + gold finish White plastic Brass + gold finish Blue plastic Brass + gold finish 900029 900025 900486 900028 900026 900332 DUMMY CONTACTS Contact size Metal dummy contacts are recommended for applications requesting EMI protection. PIGGY BACK GROMMET Type of contact Cable OD (mm) Proprietary No 900471 Size 8 power 4.4 to 5.2 Size 8 twinax and coax 3 to 4.4 900472 Size 8 twinax and coax 3 to 4.4 900476* 3 to 4.4 603015 4.4 to 5.2 603016 Quadrax * to use for arrangements 25-20, 19-17 58 Accessories Accessories Amphenol ACCESSORIES Reducing ferrule No Contact size Wire Gauge Pin contacts 900154 8 10 900197/ 900198 900092 12 Socket contacts Crimping tool 900217 16 900090 20 22D 900094 1 7 6 20 5 20 6 M22520/1-01+ M22520/1-04 6 4 26 28 4 3 26 2 28 2 32 900004 900044 M22520/2-01 + M22520/2-09 or M22520/2-07 34 2 2 5 24 30 900099 6 18 24 900091 Type 16 22 900093 809872+809873 Selector position Accessories REDUCING FERRULE 4 5 4 2 2 2 2 The sealing of mated connectors is only guaranteed for the minimum wire outside diameter given in the table page 7 Type 1 Type 2 Accessories 59 Amphenol Glossary GLOSSARY Appendix Glossary INSERTION FORCE: It's force resulting when the pin contact get engaged in the socket contact. It's usually given in Newtons INSULATOR: It's the plastic components located between contacts for multi-part contacts (COAX, TWINAX, QUADRAX). There could be multiple insulators per contacts. ELECTRICAL IMPEDANCE (or IMPEDANCE): Electrical impedance, or simply "impedance," describes a measure of opposition to alternating current (AC). Electrical impedance extends the concept of resistance to AC circuits, describing not only the relative amplitudes of the voltage and current, but also the relative phases. When the circuit is driven with direct current (DC), there is no distinction between impedance and resistance; the latter can be thought of as impedance with zero phase angle. VOLTAGE STANDARD WAVE RATIO (or VSWR): It's used to measure the efficiency of a transmission line. The value is expressed as a ratio with 1 (1:1, 2:1, 3:1). A perfect transmission line would be 1:1. CRIMPING TOOL: The crimping tool is the tool used to crimp the wire into the contact. It's usually used with a additional component called positioner or die sets. FREQUENCY RANGE: It's define the better range of frequency in utilisation to obtain the better performance of the couple cable + contact. INSERTION LOSS: It's the difference between theamount of data has been sent versus the data received. POSITIONER: This complementary component of crimping tool is used to guide, locate the crimping area of the contact during the crimping operation. DIE SET: This complementary component of crimping tool defines the hexagonal crimping die. 60 Glossary Glossary Amphenol GLOSSARY DATA RATE: Data rate is the number of "bits" of data transferred per a given unit of time. BANDWIDTH: Is the difference between the upper and lower frequencies in a continuous set of frequencies. Glossary PIGGY BACK GROMMET: The piggy back grommet is an additional device for contact size 8 which provide sealing on the wire and also guiding of the contact in the connector. DURABILITY: Is the number of mating cycle admissible by the contacts. RF LEAKAGE: Is defined as the amount of energy which "leaks" from the connector and/or component. Although RF Leakage will vary with frequency, it is typically tested at only one frequency. Leakage, like Insertion Loss, is expressed in dB. Very large negative dB values indicate that the device does not radiate much energy. DIFFERENTIAL PAIR: Differential signaling is a method of transmitting information electrically with two complementary signals sent on two paired wires, called a differential pair. Glossary 61 Amphenol Contact and Cable Selection Guide CONTACT AND CABLE SELECTION GUIDE COAXIAL PIN Contact and Appendix Cable Selection Guide Most Appropriate Cable Impedance Contact Size RG-58C/U (M17/028-RG058) RG-58 (M17/155-00001) RG-142B/U (M17/060-RG142) 62 MIL-DTL-38999 EN4165 Contact Size vs Frequency EN3645 Series Series Series Cable Standard I II III 600901 X X X X X 50 8 600901 X X X X X 50 8 900136 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X RG-174A/U (M17/119-RG174) 50 RG-178B/U (M17/093-RG178) 50 RG-179B/U (M17/094-RG179) 75 RG-180B/U (M17/095-RG180) 95 RG-187A/U (M17/094-RG179) 75 RG-188A/U (M17/113-RG316) 50 95 50 50 RG-316/U (M17/113-RG316) 50 RD-316 50 (M17/152-00001) RG-400 (M17/128-RG400) 50 50 50 TFLEX-405 50 Filotex ET124962 PAN6422XQ Belden RG59 0,8/3,7 Draka HD PRO 0,8/3,7 AF Haveg 61-02051 50 75 75 Haveg 8100207 Impedance Match 8 70 TFLEX-402 P/N 50 RG-161/U RG-195A/U (M17/095-RG180) RG-196A/U (M17/169-00001) RG-223/U (M17/084-RG223) Standard Connector 75 16 12 8 16 12 8 16 12 16 12 8 8 6 12 8 16 12 8 16 12 8 12 8 * M39029/76-424 M39029/28-211 * M39029/76-424 M39029/28-211 * * * M39029/76-425 M39029/76-424 M39029/28-211 * * * M39029/28-409 M39029/60-367 M39029/76-424 M39029/28-211 071094 900340 900135 071094 900340 900135 070247 600907 071094 900340 600822 900135 600757 900341 900130 071094 900340 500135 071094 900340 900135 900341 900130 X X X X X X X X (3G-SDI) X X X X * M39029/76-424 M39029/28-211 * M39029/28-409 * M39029/76-425 070247 900136 X X X X X * M39029/76-424 M39029/28-211 071094 900340 900384 900135 900385 900137 900385 900138 600922 600923 600606 600924 600921 600600 600920 900385 600906 600813 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 6 600813 X 16 16 12 900186 071094 900340 16 8 16 12 12 8 12 8 8 8 8 8 8 12 8 8 8 12 12 6 * * M39029/103 * M39029/103 * * * * M39029/103 M39029/76-424 M39029/28-211 Contact and Cable Selection Guide X X X X X X X X X 12GHz 18GHz 26,5GHz 65GHz 18GHz 26,5GHz 40GHz X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Amphenol Contact and Cable Selection Guide CONTACT AND CABLE SELECTION GUIDE COAXIAL PIN Cable Grun 0,6/3,7 Gore GWN1159A Gore CXN340 Impedance Contact Size 75 Times AA3248 Times LMR-195-UF Teledyne 11299 Raychem 5021D13311-0 Raychem 5021D1331-0 Raychem 5022E5111 50 Raychem 9528A1318 75 P/N * M39029/76-424 M39029/28-211 * M39029/76-424 8 Raychem7528H1424 Raychem 9528A1318 6 12 12 16 12 8 8 16 12 8 Standard 95 600813 900428 600907 071094 900340 900135 600901 071094 900340 900135 Impedance Match X Connector MIL-DTL-38999 EN4165 Contact Size vs Frequency EN3645 Series Series Series Cable Standard I II III X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 600904 X X X X X 8 600902 X X X X X 12 16 12 12 12 8 12 900424 071094 900341 900340 071954 900130 900426 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 600900 X X X X X 600903 900138 900138 900138 600830 600830 600830 600830 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 600830 X X X X X X * M39029/76-424 M39029/28-409 M39029/28-211 * Raychem 9530A5314 95 Tensolite 8 28895/2X1 ESC432101 8 ECS3C058A 8 ECS352001 8 ECS432101 8 PIC V75268 75 8 PIC V75248 8 PIC V75261 75 8 PIC V73263 75 8 EMTQ TFLEX 12575 8 075.01 *Mean the best match between cable and contacts M39029/60-367 X X Contact and Cable Selection Guide Contact and Cable Selection Guide Most Appropriate 63 Amphenol Contact and Cable Selection Guide CONTACT AND CABLE SELECTION GUIDE COAXIAL SOCKET Most Appropriate Contact and Appendix Cable Selection Guide Cable RG-58C/U (M17/028-RG058) RG-58 (M17/155-00001) RG-142B/U (M17/060-RG142) RG-161/U RG-174A/U (M17/119-RG174) RG-178B/U (M17/093-RG178) RG-179B/U (M17/094-RG179) RG-180B/U (M17/095-RG180) RG-187A/U (M17/094-RG179) RG-188A/U (M17/113-RG316) RG-195A/U (M17/095-RG180) RG-196A/U (M17/169-00001) RG-223/U (M17/084-RG223) RG-316/U (M17/113-RG316) 64 Impedance Contact Size Standard P/N Connector MIL-DTL-38999 EN4165 Impedance Contact Match Size vs Frequency EN3645 Series Series Series Series Cable Standard I II III III 50 8 600911 X X X X 50 8 600911 X X X X 50 8 900146 X X X X X X X X X X 70 50 50 75 95 74 50 95 50 50 50 RD-316 50 (M17/152-00001) RG-400 (M17/128-RG400) 50 TFLEX-402 50 50 16 16 12 12 8 16 16 12 12 8 16 12 16 12 16 12 12 8 8 6 12 12 8 16 16 12 12 8 16 16 12 12 8 12 12 8 16 16 * * * * * M39029/78-432 M39029/77-428 M39029/27-210 M39209/75-416 M39029/78-432 M39029/77-428 M39029/27-210 M39209/75-416 M39029/78-433 M39029/77-429 * * M39029/78-432 M39029/27-210 M39209/75-416 * * * * * * * * * M39029/27-402 M39029/75-417 M39029/59-366 M39029/78-432 M39029/77-428 M39029/27-210 M39029/75-417 M39029/78-432 M39029/77-428 M39029/27-210 M39029/75-417 M39029/27-210 M39029/75-417 M39029/78-433 M39029/77-429 8 16 16 12 12 12 8 12 8 12 8 8 8 8 077987 070248 900354 900350 900145 077987 070248 900354 900350 900145 071998 600659 071965 600917 077987 900354 900350 600841 900145 603180 900286 900351 900140 077987 070248 900354 900351 900145 077987 070248 900354 900351 900145 900354 900351 900140 071998 071965 X X X X X X X X M39029/78-432 M39029/77-428 M39029/27-210 M39209/75-416 * * M39029/102 * M39029/102 * * 077987 070248 900354 900350 600750 900145 900395 900147 900395 900148 600927 600919 600581 Contact and Cable Selection Guide X X X X X X X X X X X X X X X X X X (3G-SDI) X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 12GHz 18GHz 26,5GHz X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 900146 * * X X X X X X X X X X X X X X X X X X X Amphenol Contact and Cable Selection Guide CONTACT AND CABLE SELECTION GUIDE COAXIAL SOCKET Cable Impedance Contact Size TFLEX-405 50 Filotex ET124962 PAN6422XQ Belden RG59 0,8/3,7 Draka HD PRO 0,8/3,7 AF 50 50 75 75 Haveg 61-02051 Haveg 8100207 Grun 0,6/3,7 75 Gore GWN1159A Gore CXN3403 Times AA3248 Times LMR-195-UF Teledyne 11299 Raychem 5021D13311-0 Raychem 5021D1331-0 Raychem 5022E5111 Raychem 7527A1318 50 75 Raychem 7528H1424 Raychem 9528A1318 Raychem 9530A5314 Tensolite 28895/2X1 ESC432101 ECS3C058A ECS352001 ECS432101 PIC V75268 PIC V75248 PIC V75261 PIC V73263 EMTQ TFLX 125075-01 95 95 12 8 8 8 12 12 6 Standard P/N * 600928 600926 600580 600925 900395 600916 600715 * M39029/102 6 600715 16 16 16 16 12 12 6 12 12 12 16 16 12 12 8 8 16 16 12 12 8 900187 603247 077987 070248 900354 900350 600715 900429 900075 600917 077987 070248 900354 900350 900145 600911 077987 070248 900354 900350 900145 * * * * M39029/78-432 M39029/77-428 M39029/27-210 M39209/75-416 M39029/78-432 M39029/77-428 M39029/27-210 M39209/75-416 M39029/78-432 M39029/77-428 M39029/27-210 M39209/75-416 Connector MIL-DTL-38999 EN4165 Impedance Contact Match Size vs Frequency EN3645 Series Series Series Series Cable Standard I II III III X X X X X X X 65GHz 18GHz X X X X 26,5GHz X X X X 40GHz X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X M39029/27-210 900425 900421 077587 070248 900354 900350 900354 M39209/75-416 900350 X X X X X X X X X X X X X X X X X X X 900140 X X X X X X X X 900420 900430 600836 X X X X X X X X X X X X X 600912 8 X X X 8 900427 900422 600910 600913 900148 900148 900148 600836 600836 600836 600836 X X X X 12 12 16 16 12 12 12 12 12 12 8 12 12 8 8 8 8 8 8 8 8 8 M39029/59-366 X X X X * * X X X X 600914 M39029/27-210 M39209/75-416 X X X 8 * M39029/78-432 * M39029/77-428 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X Contact and Cable Selection Guide Contact and Cable Selection Guide Most Appropriate 65 Amphenol Contact and Cable Selection Guide CONTACT AND CABLE SELECTION GUIDE TWINAX PIN AND SOCKET P/N Contact and Appendix Cable Selection Guide Cable Impedance Contact Size M17-176-0002 AS39029/90-529 AS39029/113-625 711-1760-104 EN3155-024M08AB EN3155-024M08BB ABS2217P03 ABS1600M08A EN3155-024M08CB PIN SKT 074834 072453 900937 900938 600611 600612 600858 140675 600613 600856 600854 600614 600615 600859 140683 600616 600857 600855 EN3375-003 KG24 77 EN3375-004 WJ24 77 EN3375-005 WV24 EN3375-006 XM24 EN3375-009 WS26 Raychem 10612 Raychem 10613 Raychem 10614 EPD44690 EPD44691 EPD44692 EPD44695 PAN 6421 Mc Donnell Douglas SM2022/003 ASNE08072003-09 AXON P509782 Tensolite 24463/05099X-8(LD) Tensolite 24463/9P025X-2(LD) Tensolite 26453/03184X-2(LD) Tensolite 24460/05114X-2(LD) Tensolite 24463/03220T-2 (LD) Tensolite 26453/03184X-2(LD) 77 78 120 77 77 77 77 77 77 77 77 8 (ARINC) 8 8 8 8 8 8 8 8 8 8 8 77 8 100 100 8 8 600933 600943 600934 600944 100 8 900418 100 8 100 Tensolite 26483/03071X-2(LD) Thermax MX 100-24 Thermax 12814 Thermax 956-626Z Thermax 956-1T200 ST5M1284-003 26463/70460X-2 PIC E10224 PIC E1024 Draka 2709-3 NF24T100-200C S280W502-1 S280W502-6 GORE GSC-05-827300-00 GORE DXN 2125 JSFY11-24 66 77 8 8 8 8 8 8 Standard Connector ABS2217P01 711-1060-104 711-1760-102 711-1760-101 711-1760-104 711-1760-104 711-1760-101 711-1760-101 711-1760-102 CONCENTRIC CONCENTRIC DIFFERENTIAL CONCENTRIC CONCENTRIC CONCENTRIC CONCENTRIC CONCENTRIC CONCENTRIC CONCENTRIC CONCENTRIC CONCENTRIC CONCENTRIC CONCENTRIC CONCENTRIC CONCENTRIC CONCENTRIC CONCENTRIC CONCENTRIC BUS1553 BUS1553 BUS1553 BUS1553 BUS1553 BUS1553 BUS1553 BUS1553 BUS1553 BUS1553 BUS1553 BUS1553 BUS1553 BUS1553 BUS1553 BUS1553 BUS1553 X X DIFFERENTIAL ETHERNET USB DIFFERENTIAL X X X X X X X X 900419 DIFFERENTIAL ETHERNET USB X X X X 900418 900419 DIFFERENTIAL ETHERNET USB X X X X 8 600933 600934 DIFFERENTIAL ETHERNET USB X X X X 100 8 600935 600934 DIFFERENTIAL ETHERNET USB X X X X 100 8 600939 600940 DIFFERENTIAL ETHERNET USB X X X X 100 8 600945 600946 DIFFERENTIAL X X X X 900294 900299 DIFFERENTIAL X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 100 100 100 100 98 98 100 100 100 100 100 100 8 8 8 8 8 8 8 8 8 8 8 8 600858 600899 DIFFERENTIAL 900418 900418 600933 600931 900418 900418 900418 600935 900418 900418 900418 600941 900419 900419 600934 600932 900419 900419 900419 600936 900419 900419 900419 600942 DIFFERENTIAL DIFFERENTIAL DIFFERENTIAL DIFFERENTIAL DIFFERENTIAL DIFFERENTIAL DIFFERENTIAL DIFFERENTIAL DIFFERENTIAL DIFFERENTIAL DIFFERENTIAL DIFFERENTIAL BUS1553 Sim Connector EN3645 Series III Series Series Series I II III X X X X X X X X X X X X X X X X X X X X X X X X X X X X ARINC CONNECTOR X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X MIL-DTL-38999 X 8 CONCENTRIC Protocol X 150 711-1760-103 Concentric differential FIBRE CHANNEL ETHERNET 1000BASE-T ETHERNET ETHERNET ETHERNET USB ETHERNET USB ETHERNET USB ETHERNET USB ETHERNET USB ETHERNET USB ETHERNET USB ETHERNET USB ETHERNET USB ETHERNET USB 100 8 600931 600932 DIFFERENTIAL ETHERNET USB X X X X 100 100 8 8 600947 600939 600948 600940 DIFFERENTIAL DIFFERENTIAL ETHERNET USB X X X X X X X X Contact and Cable Selection Guide Amphenol AbOut AMphenOl Amphenol has a diversified presence as a leader in high growth areas of the interconnect industry and provides solutions for customers in the automotive, broadband, industrial, information technology and data communications, military and aerospace, mobile devices, and mobile networks markets. Amphenol More info on www.amphenol.com eNABliNG THe eleCTrONiCS reVOlUTiON Amphenol Military & Aerospace Operations (AMAO) has the largest and broadest selection of interconnect products in the military and aerospace markets. Contact and Cable Selection Guide Founded in 1932, Amphenol is one of the largest manufacturers of interconnect products in the world. The company designs, manufactures, and markets electrical, electronic, and fiber optic connectors, interconnect systems, and coaxial and specialty cables. More info on www.amphenolmao.com europe frAnce Amphenol Air lB 2 rue Clement Ader, zAC de We - 08110 carignan +33 3 24 22 78 49 frAnce Amphenol SeFee z.i. des Cazes - BP243 - 12402 Saint-Affrique Cedex +33 5 65 98 11 00 gerMAnY Amphenol Air lB GMBH Am Kleinbahnhof 4 - 66740 Saarlouis +49 6831 981 00 itAlY Amphenol euroPeAn SAleS oPerATionS Via Barbaiana n.5 - 20020 lainate - Milano +39 293 254 214 uniteD KingDOM Amphenol iNVOTeC Unit 1-3, Hedging lane industrial estate, Dosthill - Tamworth, B77 5HH +44 1827 263 000 uniteD KingDOM Amphenol ionix SySTeMS Prospect House, Taylor Business Park, risley, Warrington, WA3 6HP +44 1 942 685 200 uniteD KingDOM Amphenol lTD Thanet Way, Whitstable - KeNT, cT53JF +44 1227 773 200 uniteD KingDOM Amphenol MArTec St Augustines Business Park, Swalecliffe Whitstable - Kent CT5 2QJ +44 1227 793 733 north America cAnADA Amphenol cAnADA 605 Milner avenue - Toronto, ontario +1 416 291 0647 usA Amphenol AeroSPAce oPerATionS 40-60 Delaware street - Sidney, ny 13838 +1 800 678 0141 usA Amphenol BOriSH TeCHNOlOGieS 4511 east Paris AVe - Grand rapids, Mi 49512 +1 616 554 9820 usA Amphenol FSi 1300 central expwy n, Suite 100 - Allen, Tx 75013 +1 214 547 2400 +1 928 634 3685 usA Amphenol griFFiTh enTerPriSeS 6000 east Coury Drive - Cottonwood, Az 86326 usA Amphenol nexuS TechnologieS 50 Sunnyside Avenue - Stamford, cT 06902 +1 203 327 7300 usA Amphenol PcD 72 Cherry Hill Drive - Beverly, MA. 01915 +1 978 624 3400 usA Amphenol PrinTeD circuiT Board Technology, 91 Northeastern Boulevard - Nashua, NH 03062 +1 603 324 4500 usA Amphenol SV MiCrOWAVe 2400 Centrepark West Drive - West Palm Beach, Fl +1 561 840 1800 usA Amphenol TiMeS MiCrOWAVe 358 Hall Avenue - Wallingford, CT 06492 +1 800 867 2629 Asia chinA Amphenol PcD co. Building 21, 1st liao Keng industrial zone, Shi Yan Street - Bao An District - Shenzhen 518108 +86 755 8173 8000/8286 inDiA Amphenol inTerconnecT inDiA 105 Bhosari industrial Area - Pune 411 026 +91 20 27120363 JApAn Amphenol JAPAn 471-1, Deba, ritto-City - Shiga 520 3041 +81 77 553 8501 KOreA Amphenol DAeShin 558 SongNae-Dong SoSa-Gu, Bucheon-city, Kyunggi-Do - 420-130 +81 32 610 3830/3845 singApOre Amphenol eAST ASiA 26/F, railway Plaza, 39 Chatham road South, Tsim Sha Tsui, Kowloon, Hong Kong +65 6294 2128 Other Areas AfricA Amphenol AFricA 30 impala rd - Sandton 2146 +27 82 410 5179 ArgentinA Amphenol ArgenTinA Av. Callao 930 2do piso Oficina B "Plaza" c1023 - AAP Buenos Aires +54 11 4815 6886 AustrAliA Amphenol AuSTrAliA PTy 2 Fiveways Blvd., Keysborough - Melbourne - Victoria 3173 +61 3 8796 8888 brAzil Amphenol DO BrAzil rua Diogo Moreira, 132, 20 andar, rooms 2001-2-3 +55 11 3815 1003 isrAel Amphenol BAr-TeC 3 Hagavish Street, K fir-Barkan Bldg. east industrial zone - Kfar-Sava, 44102 +972 9 764 4100 MexicO Amphenol OPTiMize Carretera internacional Km 6.5, Col. Parque industrial, Nogales, Sonora, C.P. 84094 +52 631 311 160 neW zeAlAnD Amphenol PHiTeK level 4, 2 Kingdon Street, Newmarket, Auckland 1023 +64 9 524 2984 russiA Amphenol ruSSiA yaroslavskaja Street 8 - 129164 Moscow +7 495 937 6341 turKeY Amphenol TUrKeY Sun Plaza 15 Kat: 15 Maslak Hah. Bilim Sok. No.5 - Sisli/istanbul, 34398 +90 212 367 92 19 67 Amphenol Socapex 948, promenade de l'Arve BP29 74311 Thyez Cedex - France Phone: +33 (0)4 50 89 28 00 contact@amphenol-socapex.fr www.amphenol-socapex.com For Technical Support +33 (0)4 50 89 28 49 technicalsupport@amphenol-socapex.fr www.amphenol-socapex.com/technical_support To buy our products +33 (0)4 50 90 28 00 contact@amphenol-socapex.fr www.amphenol-socapex.com/amphenol/sales Request a quote online at www.amphenol-socapex.com/quotation_request Documentation www.amphenol-socapex.com/documentation To order a paper version of our catalogs, send an e-mail to communication@amphenol-socapex.fr www.amphenol-socapex.com Follow Amphenol Socapex on social media : This catalog uses paper from managed forests, PEFC & FSC labels, and is printed by a printer certified "Imprim'Vert(R)" We reserve the right to modify our products in any way we deem necessary. Any duplication is prohibited, unless approved in writing. Designed by Amphenol Socapex DOC-000081-ANG - May 2019