DS92LV3221,DS92LV3222 DS92LV3221/DS92LV3222 20-50 MHz 32-Bit Channel Link II Serializer / Deserializer Literature Number: SNLS319B DS92LV3221/DS92LV3222 20-50 MHz 32-Bit Channel Link II Serializer / Deserializer General Description Features The DS92LV3221 (SER) serializes a 32-bit data bus into 2 embedded clock LVDS serial channels for a data payload rate up to 1.6 Gbps over cables such as CATx, or backplanes FR-4 traces. The companion DS92LV3222 (DES) deserializes the 2 LVDS serial data channels, de-skews channel-to-channel delay variations and converts the LVDS data stream back into a 32-bit LVCMOS parallel data bus. On-chip data Randomization/Scrambling and DC balance encoding and selectable serializer Pre-emphasis ensure a robust, low-EMI transmission over longer, lossy cables and backplanes. The Deserializer automatically locks to incoming data without an external reference clock or special sync patterns, providing an easy "plug-and-lock" operation. By embedding the clock in the data payload and including signal conditioning functions, the Channel-Link II SerDes devices reduce trace count, eliminate skew issues, simplify design effort and lower cable/connector cost for a wide variety of video, control and imaging applications. A built-in ATSPEED BIST feature validates link integrity and may be used for system diagnostics. Wide Operating Range Embedded Clock SER/DES -- Up to 32-bit parallel LVCMOS data -- 20 to 50 MHz parallel clock -- Up to 1.6 Gbps application data paylod Simplified Clocking Architecture -- No separate serial clock line -- No reference clock required -- Receiver locks to random data On-chip Signal Conditioning for Robust Serial Connectivity -- Transmit Pre-Emphasis -- Data randomization -- DC-balance encoding -- Receive channel deskew -- Supports up to 10m CAT-5 at 1.6Gbps Integrated LVDS Terminations Built-in AT-SPEED BIST for end-to-end system testing AC-coupled interconnect for isolation and fault protection > 4KV HBM ESD protection Space-saving 64-pin TQFP package Full industrial temperature range : -40 to +85C Applications Industrial imaging (Machine-vision) and control Security & Surveillance cameras and infrastructure Medical imaging Block Diagram 30105727 TRI-STATE(R) is a registered trademark of National Semiconductor Corporation. (c) 2010 National Semiconductor Corporation 301057 www.national.com DS92LV3221/DS92LV3222 20-50 MHz 32-Bit Channel Link II Serializer / Deserializer January 19, 2010 DS92LV3221/DS92LV3222 DS92LV3221 Pin Diagram 30105730 FIGURE 1. DS92LV3221 Pin Diagram-- Top View www.national.com 2 DS92LV3221/DS92LV3222 DS92LV3221 Serializer Pin Descriptions Pin # Pin Name I/O, Type Description LVCMOS PARALLEL INTERFACE PINS 10-8, 5-1, 64-57, 52-51, 48-44. 41-33 TxIN[31:29], TxIN[28:24], TxIN[23:16], TxIN[15:14], TxIN[13:9], TxIN[8:0] I, LVCMOS Serializer Parallel Interface Data Input Pins. 11 TxCLKIN I, LVCMOS Serializer Parallel Interface Clock Input Pin. Strobe edge set by R_FB configuration pin. CONTROL AND CONFIGURATION PINS 12 PDB I, LVCMOS Serializer Power Down Bar (ACTIVE LOW) PDB = L; Device Disabled, Differential serial outputs are put into TRI-STATE(R) stand-by mode, PLL is shutdown PDB = H; Device Enabled 19 PRE I, LVCMOS PRE-emphasis level select pin PRE = (RPRE > 12k); Imax = [(1.2/R) x 20 x 2], Rmin = 12k. PRE = H or floating; pre-emphasis is disabled. 14 R_FB I, LVCMOS Rising/Falling Bar Clock Edge Select R_FB = H; Rising Edge, R_FB = L; Falling Edge 20 VSEL I, LVCMOS VOD (Differential Output Voltage) Llevel Select VSEL = L; Low Swing, VSEL = H; High Swing 13 BISTEN I, LVCMOS BIST Enable BISTEN = L; BIST OFF, (default), normal operating mode. BISTEN = H; BIST Enabled (ACTIVE HIGH) 15, 16 RSVD I, LVCMOS Reserved -- MUST BE TIED LOW 21, 22, 23, 24 NC Do Not Connect, leave pins floating LVDS SERIAL INTERFACE PINS 28, 30 TxOUT[1:0]+ O, LVDS Serializer LVDS Non-Inverted Outputs(+) 27, 29 TxOUT[1:0]- Serializer LVDS Inverted Outputs(-) O, LVDS POWER / GROUND PINS 7, 18, 32, 42 VDD VDD Digital Voltage supply, 3.3V 6, 17, 31, 43 VSS GND Digital ground 53, 56 VDDPLL VDD Analog Voltage supply, PLL POWER, 3.3V 54, 55 VSSPLL GND Analog ground, PLL GROUND 26 VDDA VDD Analog Voltage supply 25 VSSA GND Analog ground 49 IOVDD VDD Digital IO Voltage supply Connect to 1.8V typ for 1.8V LVCMOS interface Connect to 3.3V typ for 3.3V LVCMOS interface 50 IOVSS GND Digital IO ground 3 www.national.com DS92LV3221/DS92LV3222 DS92LV3222 Pin Diagram 30105731 FIGURE 2. DS92LV3222 Pin Diagram -- Top View www.national.com 4 DS92LV3221/DS92LV3222 DS92LV3222 Deserializer Pin Descriptions Pin # Pin Name I/O, Type Description LVCMOS PARALLEL INTERFACE PINS 5-7, 10-14, 19-25, 28-32, 33-39, 42-46 RxOUT[31:29], RxOUT[28:24], RxOUT[23:17], RxOUT[16:12], RxOUT[11:5], RxOUT[4:0] O, LVCMOS Deserializer Parallel Interface Data Output Pins. 4 RxCLKOUT O, LVCMOS Deserializer Recovered Clock Output. Parallel data rate clock recovered from the embedded clock. 3 LOCK O, LVCMOS LOCK indicates the status of the receiver PLL LOCK = L; deserializer CDR/PLL is not locked, RxOUT[31:0] and RCLK are TRI-STATED(R) LOCK = H; deserializer CDR/PLL is locked CONTROL AND CONFIGURATION PINS 48 R_FB I, LVCMOS Rising/Falling Bar Clock Edge Select R_FB = H; RxOUT clocked on rising edge R_FB = L; RxOUT clocked on falling edge 50 REN I, LVCMOS Deserializer Enable, DES Output Enable Control Input (ACTIVE HIGH) REN = L; disabled, RxOUT[31:0] and RxCLKOUT TRI-STATED, PLL still operational REN = H; Enabled (ACTIVE HIGH) 49 PDB I, LVCMOS Power Down Bar, Control Input Signal (ACTIVE LOW) PDB = L; disabled, RxOUT[31:0], RCLK, and LOCK are TRI-STATED in stand-by mode, PLL is shutdown PDB = H; Enabled 47 RSVD I, LVCMOS Reserved -- MUST BE TIED LOW 57, 58, 59, 60 NC Do Not Connect, leave pins floating LVDS SERIAL INTERFACE PINS 51, 53 RxIN[0:1]+ I, LVDS Deserializer LVDS Non-Inverted Inputs(+) 52, 54 RxIN[0:1]- I, LVDS Deserializer LVDS Inverted Inputs(-) POWER / GROUND PINS 9, 16, 17, 26, 61 VDD VDD Digital Voltage supply, 3.3V 8, 15, 18, 27, 62 VSS GND Digital Ground 55 VDDA VDD Analog LVDS Voltage supply, POWER, 3.3V 56 VSSA GND Analog LVDS GROUND 1, 40, 64 VDDPLL VDD Analog Voltage supply PLL VCO POWER, 3.3V 2, 41, 63 VSSPLL GND Analog ground, PLL VCO GROUND 5 www.national.com DS92LV3221/DS92LV3222 Recommended Operating Conditions Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VDD) Supply Voltage (IOVDD) (SER ONLY) 3.3V I/O Interface 1.8V I/O Interface Operating Free Air Temperature (TA) Input Clock Rate Tolerable Supply Noise Supply Voltage (VDD) -0.3V to +4V LVCMOS Input -0.3V to (VDD +0.3V) Voltage LVCMOS Output -0.3V to (VDD +0.3V) Voltage LVDS Deserializer Input Voltage -0.3V to +3.9V LVDS Driver Output Voltage -0.3V to +3.9V Junction Temperature +125C Storage Temperature -65C to +150C Lead Temperature (Soldering, 4 seconds) +260C Maximum Package Power Dissipation Capacity Package Derating: 1/JA C/W above +25C JA 35.7 C/W* JC 12.6 C/W *4 Layer JEDEC >4 kV ESD Rating (HBM) Min 3.135 Nom 3.3 Max 3.465 Units V 3.135 1.71 3.3 1.8 3.465 1.89 V V -40 20 +25 +85 50 100 C MHz mVP-P Electrical Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. (Note 2, Note 3) Symbol Parameter Conditions Min Typ Max Units LVCMOS DC SPECIFICATIONS VIH High Level Input Voltage Tx: IOVDD = 1.71V to 1.89V Tx: IOVDD = 3.135V to 3.465V Rx VIL Low Level Input Voltage Tx: IOVDD = 1.71V to 1.89V Tx: IOVDD = 3.135V to 3.465V Rx 0.65 x IOVDD IOVDD + 0.3 2.0 VDD GND 0.35 x IOVDD GND 0.8 VCL Input Clamp Voltage ICL = -18 mA IIN Input Current Tx: VIN = 0V or 3.465V(1.89V) IOVDD = 3.465V(1.89V) -10 +10 Rx: VIN = 0V or 3.465V -10 +10 -0.8 -1.5 V V V A VOH High Level Output Voltage IOH = -2mA 2.4 3.0 VDD V VOL Low Level Output Voltage IOH = -2mA GND 0.33 0.5 V IOS Output Short Circuit Current VOUT = 0V -22 -40 mA IOZ TRI-STATE(R) Output Current PDB = 0V, VOUT = 0V or VDD +10 A 440 (850) 525 (1000) mVP-P 1 50 mVP-P 1.25 1.50 V 4 50 mV -10 SERIALIZER LVDS DC SPECIFICATIONS VOD Output Differential Voltage VOD Output Differential Voltage Unbalance VSEL = L, No pre-emphasis VOS Offset Voltage VSEL = L, No pre-emphasis VOS Offset Voltage Unbalance VSEL = L, No pre-emphasis www.national.com No pre-emphasis, VSEL = L (VSEL = H) 6 350 (629) 1.00 IOS IOZ RT Parameter Output Short Circuit Current TRI-STATE(R) Output Current Output Termination Conditions Min Typ Max Units TxOUT[1:0] = 0V, PDB = VDD, VSEL = L, No pre-emphasis -2 -5 TxOUT[1:0] = 0V, PDB = VDD, VSEL = H, No pre-emphasis -6 -10 PDB = 0V, TxOUT[1:0] = 0V OR VDD -15 1 +15 A PDB = VDD, TxOUT[1:0] = 0V OR VDD -15 1 +15 A Internal differential output termination between differential pairs 90 100 130 mA SERIALIZER SUPPLY CURRENT (DVDD*, PVDD* AND AVDD* PINS) *DIGITAL, PLL, AND ANALOG VDDS IDDTD IDDTZ Serializer (Tx) Total Supply Current (includes load current) Serializer Supply Current Power-down f= 50 MHz, CHECKER BOARD pattern VSEL = H, PRE = OFF 120 145 f= 50 MHz, CHECKER BOARD pattern VSEL = H, RPRE = 12 k 120 145 f= 50 MHz, RANDOM pattern VSEL = H, PRE = OFF 115 135 f= 50 MHz, RANDOM pattern VSEL = H, RPRE = 12 k 115 135 2 50 A +50 mV mA TPWDNB = 0V (All other LVCMOS Inputs = 0V) DESERIALIZER LVDS DC SPECIFICATIONS VTH Differential Threshold High Voltage VTL Differential Threshold Low Voltage VCM = +1.8V RT Input Termination Internal differential output termination between differential pairs IIN Input Current -50 mV 100 130 VIN = +2.4V, VDD = 3.6V 100 250 A VIN = 0V, VDD = 3.6V 100 250 A 90 DESERIALIZER SUPPLY CURRENT (DVDD*, PVDD* AND AVDD* PINS) *DIGITAL, PLL, AND ANALOG VDDS IDDRZ Deserializer Supply Current Powerdown f = 50 MHz, CL = 8 pF, CHECKER BOARD pattern 145 f = 50 MHz, CL = 8 pF, RANDOM pattern 122 PDB = 0V (All other LVCMOS Inputs = 0V, RxIN[1:0](P/N) = 0V) 7 185 mA 140 100 A www.national.com DS92LV3221/DS92LV3222 Symbol DS92LV3221/DS92LV3222 Serializer Input Timing Requirements for TCLK Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units 20 tCIP 50 ns 0.45 x tCIP 0.5 x tCIP 0.55 x tCIP ns 20 MHz - 50 MHz Figure 5 0.45 x tCIP 0.5 x tCIP 0.55 x tCIP ns 20 MHz - 50 MHz Figure 4 0.5 1.2 ns 100 psP-P Max Units tCIP TxCLKIN Period tCIH TxCLKIN High Time 20 MHz - 50 MHz tTCIL TxCLKIN Low Time tCIT TxCLKIN Transition Time tJIT TxCLKIN Jitter Serializer Switching Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter tLLHT LVDS Low-to-High Transition Time tLHLT LVDS High-to-Low Transition Time tSTC TxIN[31:0] Setup to TxCLKIN Conditions No pre-emphasis Figure 3 IOVDD = 1.71V to 1.89V Figure 5 IOVDD = 3.135V to 3.465V tHTC TxIN[31:0] Hold from TxCLKIN Min IOVDD = 1.71V to 1.89V IOVDD = 3.135V to 3.465V tPLD Serializer PLL Lock Time Figure 7 tLZD Data Output LOW to TRI-STATE(R) Delay (Note 4) tHZD Data Output TRI-STATE(R) to HIGH Delay (Note 4) tSD Serializer Propagation Delay Latency f = 50 MHz, R_FB = H, PRE = OFF, Figure 6 Typ 350 ps 350 ps 0 ns 0 2.5 ns 2.25 4400 x tCIP 5000 x tCIP ns 5 10 ns 5 10 ns 4.5 tCIP + 6.77 f = 50 MHz, R_FB = L, PRE = OFF, 4.5 tCIP + 4.5 tCIP + 4.5 tCIP + 5.63 7.09 9.29 f = 20 MHz, R_FB = H, PRE = OFF, 4.5 tCIP + 4.5 tCIP + 4.5 tCIP + 6.57 8.74 10.74 ns tLVSKD LVDS Output Skew LVDS differential output channel-tochannel skew 30 STXBW Jitter Transfer Function -3 dB Bandwidth f = 50 MHz Figure 13 2.8 MHz STX Serializer Jitter Transfer Function Peaking f = 50 MHz 0.3 dB www.national.com 8 500 ps Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter tROCP Receiver Output Clock Period tRODC RxCLKOUT Duty Cycle tROTR LVCMOS Low-to-High Transition Time tROTF LVCMOS High-to-Low Transition Time tROSC RxOUT[31:0] Setup to RxCLKOUT tROHC RxOUT[31:0] Hold to RxCLKOUT tHZR Data Output High to TRI-STATE(R) Delay tLZR Conditions tROCP = tCIP Figure 9 Min Typ Max Units 20 tROCP 50 ns 45 50 55 % CL = 8pF (lumped load) Figure 8 f = 50 MHz Figure 11 3.2 ns 3.5 ns 5.6 0.5 x tROCP ns 7.4 0.5 x tROCP ns 5 10 ns Data Output Low to TRI-STATE(R) Delay 5 10 ns tZHR Data Output TRI-STATE(R) to High Delay 5 10 ns tZLR Data Output TRI-STATE(R) to Low Delay 5 10 ns tRD Deserializer Porpagation Delay - Latency f = 20 MHz Figure 10 f = 50 MHz tRPLLS Deserializer PLL Lock Time TOLJIT Deserializer Input Jitter Tolerance tLVSKR LVDS Differential Input Skew Tolerance 5.5 x tROCP + 3.35 ns 5.5 x tROCP + 6.00 ns 20 MHz - 50 MHz Figure 11 (Note 5) 128k x tROCP 0.25 20 MHz - 50 MHz Figure 15 ns UI 0.4 x tROCP ns Note 1: "Absolute Maximum Ratings" indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. Note 2: Typical values represent most likely parametric norms at VDD = 3.3V, TA = +25C, and at the Recommended Operating Conditions at the time of product characterization and are not guaranteed. Note 3: Current into a the device is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground except VOD, VOD, VTH, VTL which are differential voltages. Note 4: When the Serializer output is at TRI-STATE(R) the Deserializer will lose PLL lock. Resynchronization MUST occur before data transfer. Note 5: tRPLLS is the time required by the Deserializer to obtain lock when exiting power-down mode. 9 www.national.com DS92LV3221/DS92LV3222 Deserializer Switching Characteristics DS92LV3221/DS92LV3222 AC Timing Diagrams and Test Circuits 30105732 FIGURE 3. Serializer LVDS Transition Times 30105745 FIGURE 4. Serializer Input Clock Transition Time 30105749 FIGURE 5. Serializer Setup/Hold and High/Low Times 30105747 FIGURE 6. Serializer Propagation Delay www.national.com 10 DS92LV3221/DS92LV3222 30105733 FIGURE 7. Serializer PLL Lock Time 30105748 FIGURE 8. Deserializer LVCMOS Output Transition Time 30105734 FIGURE 9. Deserializer Setup and Hold times 30105746 FIGURE 10. Deserializer Propagation Delay 11 www.national.com DS92LV3221/DS92LV3222 30105735 FIGURE 11. Deserializer PLL Lock Time and PDB TRI-STATE(R) Delay 30105736 FIGURE 12. Deserializer TRI_STATE Test Circuit and Timing www.national.com 12 DS92LV3221/DS92LV3222 30105751 FIGURE 13. Serializer Jitter Transfer 30105737 FIGURE 14. Serializer VOD Test Circuit Diagram 30105738 FIGURE 15. LVDS Deserializer Input Skew 13 www.national.com DS92LV3221/DS92LV3222 This results in a per channel throughput of 400 Mbps to 1.0 Gbps (20 bits x clock rate). When all of the DES channels obtain lock , the LOCK pin is driven high and synchronously delivers valid data and recovered clock on the output. The DES locks to the clock, uses it to generate multiple internal data strobes, and then drives the recovered clock to the RxCLKOUT pin. The recovered clock (RxCLKOUT) is synchronous to the data on the RxOUT[31:0] pins. While LOCK is high, data on RxOUT[31:0] is valid. Otherwise, RxOUT[31:0] is invalid. The polarity of the RxCLKOUT edge is controlled by its R_FB (DES) input. RxOUT [31:0], LOCK and RxCLKOUT outputs will each drive a maximum of 8 pF load. REN controls TRI-STATE(R) for RxOUT0- RxOUT31 and the RxCLKOUT pin on the DES. Functional Description The DS92LV3221 Serializer (SER) and DS92LV3222 Deserializer (DES) chipset is a flexible SER/DES chipset that translates a 32-bit parallel LVCMOS data bus into 2 pairs of LVDS serial links with embedded clock. The DS92LV3221 serializes the 32-bit wide parallel LVCMOS word into two high-speed LVDS serial data streams with embedded clock, scrambles and DC Balances the data to support AC coupling and enhance signal quality. The DS92LV3222 receives the dual LVDS serial data streams and converts it back into a 32bit wide parallel data with a recovered clock. The dual LVDS serial data stream reduces cable size, the number of connectors, and eases skew concerns. Parallel clocks between 20 MHz to 50 MHz are supported. The embedded clock LVDS serial streams have an effective data payload of 640 Mbps (20MHz x 32-bit) to 1.6 Gbps (50MHz x 32- bit). The SER/DES chipset is designed to transmit data over long distances through standard twisted pair (TWP) cables. The differential inputs and outputs are internally terminated with 100 ohm resistors to provide source and load termination, minimize stub length, to reduce component count and further minimize board space. The DES can attain lock to a data stream without the use of a separate reference clock source; greatly simplifying system complexity and reducing overall cost. The DES synchronizes to the SER regardless of data pattern, delivering true automatic "plug-and-lock" performance. It will lock to the incoming serial stream without the need of special training patterns or special sync characters. The DES recovers the clock and data by extracting the embedded clock information, deskews the serial data channels and then deserializes the data. The DES also monitors the incoming clock information, determines lock status, and asserts the LOCK output high when lock occurs. In addition the DES also supports an optional AT-SPEED BIST (Built In Self Test) mode, BIST error flag, and LOCK status reporting pin. The SER and the DES have a power down control signal to enable efficient operation in various applications. RESYNCHRONIZATION In the absence of data transitions on one of the channels into the DES (e.g. a loss of the link), it will automatically try to resynchronize and re-establish lock using the standard lock sequence on the master channel (Channel 0). For example, if the embedded clock is not detected one time in succession on either of the serial links, the LOCK pin is driven low. The DES then monitors the master channel for lock, once that is obtained, the second channel is locked and aligned. The logic state of the LOCK signal indicates whether the data on RxOUT is valid; when it is high, the data is valid. The system may monitor the LOCK pin to determine whether data on the RxOUT is valid. POWERDOWN The Powerdown state is a low power sleep mode that the SER and DES may use to reduce power when no data is being transferred. The respective PDB pins are used to set each device into power down mode, which reduces supply current into the A range. The SER enters Powerdown when the SER PDB pin is driven low. In Powerdown, the PLL stops and the outputs go into TRI-STATE(R), disabling load current and reducing current supply. To exit Powerdown, SER PDB must be driven high. When the SER exits Powerdown, its PLL must lock to TxCLKIN before it is ready for sending data to the DES. The system must then allow time for the DES to lock before data can be recovered. The DES enters Powerdown mode when DES PDB is driven low. In Powerdown mode, the PLL's stop and the outputs enter TRI-STATE(R). To bring the DES block out of the Powerdown state, the system drives DES PDB high. Both the SER and DES must relock before data can be transferred from Host and received by the Target. The DES will startup and assert LOCK high when it is locked to the embedded clocks. See also Figure 11. DESKEW AND CHANNEL ALIGNMENT The DES automatically provides a clock alignment and deskew function without the need for any special training patterns. During the locking phase, the embedded clock information is recovered on all channels and the serial links are internally synchronized, de-skewed, and auto aligned. The internal CDR circuitry will dynamically compensate for up to 0.4 times the parallel clock period of per channel phase skew (channel-to-channel) between the recovered clocks of the serial links. This provides skew phase tolerance from mismatches in interconnect wires such as PCB trace routing, cable pairto-pair length differences, and connector imbalances. TRI-STATE(R) For the SER, TRI-STATE(R) is entered when the SER PDB pin is driven low. This will TRI-STATE(R) the driver output pins on TxOUT[1:0]+/-. When you drive the REN or DES PDB pin low, the DES output pins (RxOUT[31:0]) and RxCLKOUT will enter TRI-STATE(R). The LOCK output remains active, reflecting the state of the PLL. The DES input pins are high impedance during receiver Powerdown (DES PDB low) and power-off (VDD = 0V). See also Figure 11. DATA TRANSFER After SER lock is established (SER PLL to TxCLKIN), the inputs TxIN0-TxIN31 are latched into the encoder block. Data is clocked into the SER by the TxCLKIN input. The edge of TxCLKIN used to strobe the data is selectable via the R_FB (SER) pin. R_FB (SER) high selects the rising edge for clocking data and low selects the falling edge. The SER outputs (TxOUT[1:0]+/-) are intended to drive a AC Coupled point-topoint connections. The SER latches 32-bit parallel data bus and performs several operations to it. The 32-bit parallel data is internally encoded and sequentially transmitted over the two highspeed serial LVDS channels. For each serial channel, the SER transmits 20 bits of information per payload to the DES. www.national.com TRANSMIT PARALLEL DATA AND CONTROL INPUTS The DS92LV3221 operates on a core supply voltage of 3.3V with an optional digital supply voltage for 1.8V, low-swing, input support. The SER single-ended (32-bit parallel data and control inputs) pins are 1.8V and 3.3V LVCMOS logic level 14 SERIAL INTERFACE The serial links between the DS92LV3221 and the DS92LV3222 are intended for a balanced 100 Ohm interconnects. The links must be configured as an AC coupled interface. The SER and DES support AC-coupled interconnects through an integrated DC balanced encoding/decoding scheme. An external AC coupling capacitors must be placed, in series, in the LVDS signal path. The DES input stage is designed for AC-coupling by providing a built-in AC bias network which sets the internal common mode voltage (VCM) to +1.8V. For the high-speed LVDS transmission, small footprint packages should be used for the AC coupling capacitors. This will help minimize degradation of signal quality due to package parasitics. NPO class 1 or X7R class 2 type capacitors are recommended. 50 WVDC should be the minimum used for best system-level ESD performance. The most common used capacitor value for the interface is 100 nF (0.1 uF) capacitor. One set of capacitors may be used for isolation. Two sets (both ends) may also be used for maximum isolation of both the SER and DES from cable faults. The DS92LV3221 and the DS92LV3222 differential I/O's are internally terminated with 100 Ohm resistance between the inverting and non-inverting pins and do not require external termination. The internal resistance value will be between 90 ohm and 130 ohm. The integrated terminations improve signal integrity, reduce stub lengths, and decrease the external component count resulting in space savings. PRE-EMPHASIS The SER LVDS Line Driver features a Pre-Emphasis function used to compensate for extra long or lossy transmission media. The same amount of Pre-Emphasis is applied on all of the differential output channels. Cable drive is enhanced with a user selectable Pre-Emphasis feature that provides additional output current during transitions to counteract cable loading effects. The transmission distance will be limited by the loss characteristics and quality of the media. To enable the Pre-Emphasis function, the "PRE" pin requires one external resistor (Rpre) to VSS (GND) in order to set the pre-emphasized current level. Options include: 1. Normal Output (no Pre-emphasis) - Leave the PRE pin open, include an R pad, do not populate. 2. Enhanced Output (Pre-emphasis enabled) - connect a resistor on the PRE pin to Vss. Values of the Rpre Resistor should be between 12K Ohm and 100K Ohm. Values less than 6K Ohm should not be used. The amount of Pre-Emphasis for a given media will depend on the transmission distance and Fmax of the application. In general, too much Pre-Emphasis can cause over or undershoot at the receiver input pins. This can result in excessive noise, crosstalk, reduced Fmax, and increased power dissipation. For shorter cables or distances, Pre-Emphasis is typically not be required. Signal quality measurements should be made at the end of the application cable to confirm the proper amount of Pre-Emphasis for the specific application. The Pre-Emphasis circuit increases the drive current to I = 48 / (RPRE). For example if RPRE = 15 kOhms, then the current is increased by an additional 3.2 mA. To calculate the expected increase in VOD, multiply the increase in current by 50 ohms. So for the case of RPRE = 15 kOhms, the boost to VOD would be 3.2 mA x 50 Ohms = 160 mV. The duration of the current is controlled to one bit by time. If more than one bit value is repeated in the next cycle(s), the Pre-Emphasis current is turned off (back to the normal output current level) for the next bit(s). To boost high frequency data and preequalize teh data patternreduce ISI (Inter-Symbol Interference) improving the resulting eye pattern. AT-SPEED BIST FEATURE The DS92LV3221/ DS92LV3222 serial link is equipped with built-in self-test (BIST) capability to support both system manufacturing and field diagnostics. BIST mode is intended to check the entire high-speed serial interface at full link-speed without the use of specialized and expensive test equipment. This feature provides a simple method for a system host to perform diagnostic testing of both SER and DES. The BIST function is easily configured through the SER BISTEN pin. When the BIST mode is activated, the SER generates a PRBS (pseudo-random bit sequence) pattern (2^7-1). This pattern traverses each lane to the DES input. The DS92LV3222 includes an on-chip PRBS pattern verification circuit that checks the data pattern for bit errors and reports any errors on the data output pins of the DES. The AT-Speed BIST feature is enabled by setting the BISTEN to High on SER. The BISTEN input must be High or Low for 4 or more TxCLKIN clock cycles in order to activate or deactivate the BIST mode. An input clock signal for the Serializer TxCLKIN must also be applied during the entire BIST operation. Once BIST is enabled, all the Serializer data inputs (TxIN [31:0]) are ignored and the DES outputs (RxOUT[31:0]) are not available. Next, the internal test pattern generator for each channel starts transmission of the BIST pattern from SER to DES. The DES BIST mode will be automatically activated by this sequence. A maximum of 128 consecutives clock symbols on DS92LV3222 DES is needed to detect BIST enable function. The BIST is implemented with independent transmit and receive paths for the two serial links. Each channel on the DES will be individually compared against the expected bit sequence of the BIST pattern. VOD SELECT The SER Line Driver Differential Output Voltage (VOD) magnitude is selectable. Two levels are provided and are selected by the VSEL pin. When this pin is LOW, normal output levels are obtained. For most application set the VSEL pin LOW. When this pin is HIGH, the output current is increased to double the VOD level. Use this setting only for extra long cables or high-loss interconnects. VOD Control VSEL Pin Setting Effect LOW Small VOD, typ 440 mVP-P HIGH Large VOD, typ 850 mVP-P 15 www.national.com DS92LV3221/DS92LV3222 compatible and is configured through the IOVDD input supply rail. If 1.8V is required, the IOVDD pin must be connected to a 1.8V supply rail. Also when power is applied to the transmitter, IOVDD pin must be applied before or simultaneously with other power supply pins (3.3V). If 1.8V input swing is not required, this pin should be tied to the common 3.3V rail. During normal operation, the voltage level on the IOVDD pins must not change. DS92LV3221/DS92LV3222 30105741 FIGURE 16. BIST Test Enabled/Disabled Under the BIST mode, the DES parallel outputs on RxOUT [31:0] are multiplexed to represent BIST status indicators. The pass/fail status of the BIST is represented by a Pass flag along with an Error counter. The Pass flag output is designated on DES RxOUT0 for Channel 0, and RxOUT16 for Channel 1. The DES's PLL must first be locked to ensure the Pass status is valid. The output Pass status pin will stay LOW and then transition to High once 44*10^6 symbols are achieved across each of the respective transmission links. The total time duration of the test is defined by the following: 44*10^6 x tCIP . After the Pass output flags reach a HIGH www.national.com state, it will not drop to LOW even if subsequent bit errors occurred after the BIST duration period. Errors will be reported if the input test pattern comparison does not match. If an error (miss-compare) occurs, the status bit is latched on RxOUT[7:1] for Channel 0, and RxOUT[23:17] for Channel 1; reflecting the number of errors detected. Whenever a data bit contains an error, the Error counter bit output for that corresponding channel goes HIGH. Each counter for the serial link utilizes a 7-bit counter to store the number of errors detected (0 to 127 max). 16 DS92LV3221/DS92LV3222 30105742 FIGURE 17. BIST Diagram for Different Bit Error Cases * BISTEN - Mode Input - tie LOW if BIST mode is not used, or connect to host * VSEL - tie LOW for normal VOD (application dependant) * PRE - Leave open if not required (have a R pad option on PCB) * RSVD1 & RSVD2 - tie LOW There are eight power pins for the device. These may be bussed together on a common 3.3V plane (3.3V LVCMOS I/ O interface). If 1.8V input swing level for parallel data and control pins are required, connect the IOVDD pin to 1.8V. At a minimum, eight 0.1uF capacitors should be used for local bypassing. TYPICAL APPLICATION CONNECTION Figure 18 shows a typical application of the DS92LV3221 Serializer (SER). The differential outputs utilize 100nF coupling capacitors to the serial lines. Bypass capacitors are placed near the power supply pins. A system GPO (General Purpose Output) controls the PDB and BISTEN pins. In this application the R_FB (SER) pin is tied Low to latch data on the falling edge of the TxCLKIN. In this application the link is short, therefore the VSEL pin is tied LOW for the standard output swing level. The Pre-emphasis input utilizes a resistor to ground to set the amount of pre-emphasis desired by the application. Configuration pins for the typical application are shown for SER: * PDB - Power Down Control Input - Connect to host or tie HIGH (always ON) 17 www.national.com DS92LV3221/DS92LV3222 30105743 FIGURE 18. DS92LV3221 Typical Connection Diagram Figure 19 shows a typical application of the DS92LV3222 Deserializer (DES). The differential inputs utilize 100nF coupling capacitors in the serial lines. Bypass capacitors are www.national.com placed near the power supply pins. A system GPO (General Purpose Output) controls the PDB pin. In this application the R_FB (DES) pin is tied Low to strobe the data on the falling 18 * REN - tie HIGH if not used (used to MUX two DES to one target device) RSVD - tie LOW 30105744 FIGURE 19. DS92LV3222 Typical Connection Diagram 19 www.national.com DS92LV3221/DS92LV3222 * edge of the RxCLKOUT. The REN signal is not used and is tied High also. Configuration pins for the typical application are shown for DES: * PDB - Power Down Control Input - Connect to host or tie HIGH DS92LV3221/DS92LV3222 to achieve low impedance between the supply rails over the frequency of interest. At high frequency, it is also a common practice to use two vias from power and ground pins to the planes, reducing the impedance at high frequency. Some devices provide separate power and ground pins for different portions of the circuit. This is done to isolate switching noise effects between different sections of the circuit. Separate planes on the PCB are typically not required. Pin Description tables typically provide guidance on which circuit blocks are connected to which power pin pairs. In some cases, an external filter many be used to provide clean power to sensitive circuits such as PLLs. Use at least a four layer board with a power and ground plane. Locate LVCMOS signals away from the LVDS lines to prevent coupling from the LVCMOS lines to the LVDS lines. Closelycoupled differential lines of 100 Ohms are typically recommended for LVDS interconnect. The closely coupled lines help to ensure that coupled noise will appear as common mode and thus is rejected by the receivers. The tightly coupled lines will also radiate less. Applications Information TRANSMISSION MEDIA The SER and DES are used in AC-coupled point-to-point configurations, through a PCB trace, or through twisted pair cables. Interconnect for LVDS typically has a differential impedance of 100 Ohms. Use cables and connectors that have matched differential impedance to minimize impedance discontinuities. In most applications that involve cables, the transmission distance will be determined on data rates involved, acceptable bit error rate and transmission medium. PCB LAYOUT AND POWER SYSTEM CONSIDERATIONS Circuit board layout and stack-up for the LVDS SER/DES devices should be designed to provide low-noise power feed to the device. Good layout practice will also separate high frequency or high-level inputs and outputs to minimize unwanted stray noise pickup, feedback and interference. Power system performance may be greatly improved by using thin dielectrics (2 to 4 mils) for power / ground sandwiches. This arrangement provides plane capacitance for the PCB power system with low-inductance parasitics, which has proven especially effective at high frequencies, and makes the value and placement of external bypass capacitors less critical. External bypass capacitors should include both RF ceramic and tantalum electrolytic types. RF capacitors may use values in the range of 0.01 uF to 0.1 uF. Tantalum capacitors may be in the 2.2 uF to 10 uF range. Voltage rating of the tantalum capacitors should be at least 5X the power supply voltage being used. Surface mount capacitors are recommended due to their smaller parasitics. When using multiple capacitors per supply pin, locate the smaller value closer to the pin. A large bulk capacitor is recommended at the point of power entry. This is typically in the 50uF to 100uF range and will smooth low frequency switching noise. It is recommended to connect power and ground pins directly to the power and ground planes with bypass capacitors connected to the plane with vias on both ends of the capacitor. Connecting power or ground pins to an external bypass capacitor will increase the inductance of the path. A small body size X7R chip capacitor, such as 0603, is recommended for external bypass. Its small body size reduces the parasitic inductance of the capacitor. The user must pay attention to the resonance frequency of these external bypass capacitors, usually in the range of 20-30 MHz range. To provide effective bypassing, multiple capacitors are often used www.national.com PLUG AND GO The Serializer and Deserializer devices support hot plugging of the serial interconnect. The automatic receiver lock to random data "plug & go" capability allows the DS92LV3222 to obtain lock to the active data stream during a live insertion event. LVDS INTERCONNECT GUIDELINES See AN-1108 and AN-905 for full details. * Use 100 Ohm coupled differential pairs * Use the S/2S/3S rule in spacings --S = space between the pair --2S = space between pairs --3S = space to LVCMOS signal * Minimize the number of vias * Use differential connectors when operating above 500 Mbps line speed * Maintain balance of the traces * Minimize skew within the pair * Terminate as close to the TX outputs and RX inputs as possible Additional general guidance can be found in the LVDS Owner's Manual - available in PDF format from the National web site at: www.national.com/lvds 20 The waveforms below illustrate the typical performance of the DS92LV3221. The SER was given a PCLK and configured as described below each picture. In all of the pictures the SER was configured with BISTEN pin set to logic HIGH. Each waveform was taken by using a high impedance low capacitance differential probe to probe across a 100 ohm differential termination resistor within one inch of TxOUT0+/-. 30105755 30105754 Serial Output, 50 MHz, VSEL = L, No Pre-Emphasis Serial Output, 50 MHz, VSEL = H, No Pre-Emphasis 21 www.national.com DS92LV3221/DS92LV3222 Typical Performance Characteristics DS92LV3221/DS92LV3222 Physical Dimensions inches (millimeters) unless otherwise noted Dimensions show in millimeters only NS Package Number VEC64A Ordering Information NSID Package Type Package ID DS92LV3221TVS 64-Lead TQFP style, 10.0 X 10.0 X 1.0 mm, 0.5 mm pitch VEC64A DS92LV3221TVSX 64-Lead TQFP style, 10.0 X 10.0 X 1.0 mm, 0.5 mm pitch VEC64A DS92LV3222TVS 64-Lead TQFP style, 10.0 X 10.0 X 1.0 mm, 0.5 mm pitch VEC64A DS92LV3222TVSX 64-Lead TQFP style, 10.0 X 10.0 X 1.0 mm, 0.5 mm pitch, 1000 std reel VEC64A www.national.com 22 DS92LV3221/DS92LV3222 Notes 23 www.national.com DS92LV3221/DS92LV3222 20-50 MHz 32-Bit Channel Link II Serializer / Deserializer Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2010 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated