w WM8783 Stereo Low Power 96kHz ADC DESCRIPTION FEATURES The WM8783 is a compact, low cost ADC designed for set-top boxes and DVD applications. Stereo analogue inputs accept 1Vrms line level inputs; the Hi-Fi ADCs output 24-bit stereo data on the I2S digital audio interface. * * * * * * Sample rates from 8kHz to 96kHz are supported; this is configured automatically according to the external master clock (MCLK) frequency. APPLICATIONS A power on reset (POR) circuit ensures correct start-up and shut-down. The device is held in reset when MCLK is not present, offering a low-power standby state. * * * Hi-fi audio ADC (96dB SNR - `A' weighted) 2 analogue audio inputs I2S digital audio interface - sample rates 8kHz to 96kHz Automatic clocking configuration from MCLK and LRCLK Integrated voltage reference circuits 8-pin SOIC package LCD televisions Set-top boxes (STB) DVD recorders The WM8783 is supplied in an 8-pin SOIC package. BLOCK DIAGRAM WOLFSON MICROELECTRONICS plc To receive regular email updates, sign up at http://www.wolfsonmicro.com/enews Production Data, August 2010, Rev 4.0 Copyright (c)2010 Wolfson Microelectronics plc WM8783 Production Data TABLE OF CONTENTS DESCRIPTION ....................................................................................................... 1 FEATURES............................................................................................................. 1 APPLICATIONS ..................................................................................................... 1 BLOCK DIAGRAM ................................................................................................. 1 TABLE OF CONTENTS ......................................................................................... 2 PIN CONFIGURATION ........................................................................................... 3 ORDERING INFORMATION .................................................................................. 3 PIN DESCRIPTION ................................................................................................ 3 ABSOLUTE MAXIMUM RATINGS ......................................................................... 4 RECOMMENDED OPERATING CONDITIONS ..................................................... 4 THERMAL PERFORMANCE ................................................................................. 5 ELECTRICAL CHARACTERISTICS ...................................................................... 6 TERMINOLOGY ............................................................................................................. 7 SIGNAL TIMING REQUIREMENTS ....................................................................... 8 SYSTEM CLOCK TIMING .............................................................................................. 8 AUDIO INTERFACE TIMING ......................................................................................... 9 DEVICE DESCRIPTION ....................................................................................... 10 INTRODUCTION.......................................................................................................... 10 ANALOGUE-TO-DIGITAL CONVERTER (ADC) .......................................................... 10 DIGITAL AUDIO INTERFACE ...................................................................................... 10 DIGITAL FILTER CHARACTERISTICS ............................................................... 12 ADC FILTER RESPONSE............................................................................................ 12 APPLICATIONS INFORMATION ......................................................................... 14 RECOMMENDED EXTERNAL COMPONENTS........................................................... 14 AUDIO INPUT PATHS............................................................................................................................... 14 POWER SUPPLY DECOUPLING ............................................................................................................. 14 RECOMMENDED EXTERNAL COMPONENTS DIAGRAM ...................................................................... 15 PCB LAYOUT CONSIDERATIONS.............................................................................. 15 PACKAGE DIMENSIONS .................................................................................... 16 IMPORTANT NOTICE .......................................................................................... 17 ADDRESS: ................................................................................................................... 17 w PD, August 2010, Rev 4.0 2 WM8783 Production Data PIN CONFIGURATION The WM8783 is supplied in a 8-pin SOIC format. The pin configuration is illustrated below, showing the top-down view from above the chip. ORDERING INFORMATION ORDER CODE TEMPERATURE RANGE PACKAGE MOISTURE SENSITIVITY LEVEL PEAK SOLDERING TEMPERATURE WM8783GED/V -40C to +85C 8-pin SOIC (Pb-free) MSL3 260oC WM8783GED/RV -40C to +85C 8-pin SOIC (Pb-free, tape and reel) MSL3 260oC Note: Reel quantity = 3000 PIN DESCRIPTION PIN NO NAME 1 ADCDAT TYPE DESCRIPTION Digital Output ADC digital audio data Master clock 2 MCLK Digital Input 3 LRCLK Digital Input Audio interface left / right clock 4 AGND Supply Ground 5 VMIDC Analogue Output Midrail voltage decoupling capacitor 6 IN1R Analogue Input Right channel analogue input 7 IN1L Analogue Input Left channel analogue input 8 AVDD Supply Positive supply w PD, August 2010, Rev 4.0 3 WM8783 Production Data ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified. ESD Sensitive Device. This device is manufactured on a CMOS process. It is therefore generically susceptible to damage from excessive static voltages. Proper ESD precautions must be taken during handling and storage of this device. Wolfson tests its package types according to IPC/JEDEC J-STD-020B for Moisture Sensitivity to determine acceptable storage conditions prior to surface mount assembly. These levels are: MSL1 = unlimited floor life at <30C / 85% Relative Humidity. Not normally stored in moisture barrier bag. MSL2 = out of bag storage for 1 year at <30C / 60% Relative Humidity. Supplied in moisture barrier bag. MSL3 = out of bag storage for 168 hours at <30C / 60% Relative Humidity. Supplied in moisture barrier bag. The Moisture Sensitivity Level for each package type is specified in Ordering Information. MIN MAX Supply voltage (AVDD) CONDITION -0.3V 4.5V Voltage range digital inputs -0.7V AVDD +0.7V Voltage range analogue inputs -0.7V AVDD +0.7V Operating temperature range, TA -40C +85C Junction temperature, TJMAX -40C +150C Storage temperature after soldering -65C +150C RECOMMENDED OPERATING CONDITIONS PARAMETER SYMBOL MIN TYP MAX UNIT Analogue and digital I/O supply range AVDD 3.0 3.3 3.6 V Ground GND w 0 V PD, August 2010, Rev 4.0 4 WM8783 Production Data THERMAL PERFORMANCE Thermal analysis should be performed in the intended application to prevent the WM8783 from exceeding maximum junction temperature. Several contributing factors affect thermal performance most notably the physical properties of the mechanical enclosure, location of the device on the PCB in relation to surrounding components and the number of PCB layers. Connecting the GND pin through thermal vias and into a large ground plane will aid heat extraction. Three main heat transfer paths exist to surrounding air as illustrated below in Figure 1: - Package top to air (radiation). - Package bottom to PCB (radiation). - Package pins to PCB (conduction). Figure 1 Heat Transfer Paths The temperature rise TR is given by TR = PD * JA - PD is the power dissipated in the device. - JA is the thermal resistance from the junction of the die to the ambient temperature and is therefore a measure of heat transfer from the die to surrounding air. JA is determined with reference to JEDEC standard JESD51-9. The junction temperature TJ is given by TJ = TA +TR, where TA is the ambient temperature. SYMBOL MIN MAX UNIT Operating temperature range PARAMETER TA -40 85 C Operating junction temperature TJ -40 125 Thermal Resistance JA TYP TBD C C/W Note: 1. Junction temperature is a function of ambient temperature and of the device operating conditions. The ambient temperature limits and junction temperature limits must both be observed. w PD, August 2010, Rev 4.0 5 WM8783 Production Data ELECTRICAL CHARACTERISTICS Test Conditions AVDD = 3.3V, GND = 0V, TA = +25oC, 1kHz signal, fs = 48kHz, MCLK = 256fs unless otherwise stated. LRCLK transition as per Figure 4. PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT Analogue Inputs (IN1L, IN1R) Maximum input signal level Single-ended input AVDD/3.3 Vrms Input resistance 66 k Input capacitance 20 pF A-weighted, fs = 48kHz 96 dB Unweighted, fs = 48kHz 94 A-weighted, fs = 96kHz 96 ADC Input Path Performance (Analogue Input to ADC) Signal to Noise Ratio Total Harmonic Distortion SNR THD Unweighted, fs = 96kHz 94 -1dBFS input, fs = 48kHz -83 -1dBFS input, fs = 96kHz -83 Channel separation (Left/Right) Power Supply Rejection Ratio (with respect to AVDD) PSRR 1kHz 100mV pk-pk applied to AVDD dB 85 dB 50 dB Digital Inputs / Outputs Input high level 0.7 x AVDD V Input low level Output high level IOL = 1mA Output low level IOH = -1mA 0.3 x AVDD V 0.1 x AVDD V -1 1 A 2.048 12.288 MHz +4% V 0.9 x AVDD Input capacitance V 5 Input leakage pF Clocking MCLK frequency Analogue Reference Levels Midrail Reference Voltage VMID VMID resistance to Ground RVMID -4% AVDD/2 33 k Quiescent fs = 48kHz, MCLK = 256fs 7.93 mA Quiescent fs = 96kHz, MCLK = 128fs 8.74 Quiescent No clocks applied 0.24 Current Consumption AVDD Current Consumption w IAVDD PD, August 2010, Rev 4.0 6 Production Data WM8783 TERMINOLOGY 1. Signal-to-Noise Ratio (dB) - SNR is the difference in level between a full scale output signal and the device output noise with no signal applied, measured over a bandwidth of 20Hz to 20kHz. This ratio is also called idle channel noise. (No Auto-zero or Mute function is employed). 2. Total Harmonic Distortion (dB) - THD is the difference in level between a 1kHz reference sine wave output signal and the first seven harmonics of the output signal. The amplitude of the fundamental frequency of the output signal is compared to the RMS value of the next seven harmonics and expressed as a ratio. Total Harmonic Distortion plus Noise (dB) - THD+N is the difference in level between a 1kHz reference sine wave output signal and all noise and distortion products in the audio band. The amplitude of the fundamental reference frequency of the output signal is compared to the RMS value of all other noise and distortion products and expressed as a ratio. Channel Separation (L/R) (dB) - is a measure of the coupling between left and right channels. A full scale signal is applied to the left channel only, and the right channel amplitude is measured. Next, a full scale signal is applied to the right channel only, and the left channel amplitude is measured. The worst case channel separation is quoted; this is the difference in level between the full-scale output and the cross-channel output signal level, expressed as a ratio. 3. 4. 5. Power Supply Rejection Ratio (dB) - PSRR is a measure of ripple attenuation between a power supply rail and a signal output path. With the signal path idle, a small sine wave ripple is applied to power supply rail. The amplitude of the supply ripple is compared to the amplitude of the output signal generated and is expressed as a ratio. 6. All performance measurements are carried out with 20kHz AES17 low pass filter for distortion measurements, and an A-weighted filter for noise measurement. Failure to use such a filter will result in higher THD and lower SNR and Dynamic Range readings than are found in the Electrical Characteristics. The low pass filter removes out-of-band noise; although it is not audible, it may affect dynamic specification values. w PD, August 2010, Rev 4.0 7 WM8783 Production Data SIGNAL TIMING REQUIREMENTS SYSTEM CLOCK TIMING tMCLKY MCLK tMCLKL tMCLKH Figure 2 Master Clock Timing Test Conditions AVDD = 3.3V, GND = 0V, TA = +25oC. PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNIT Master Clock Timing MCLK frequency 1 / TMCLKY fs = 8kHz 2.048 fs = 16kHz 4.096 fs = 32kHz 8.192 fs = 44.1kHz 11.2896 fs = 48kHz 12.288 fs = 88.2kHz 11.2896 fs = 96kHz MCLK duty cycle (= TMCLKH : TMCLKL) w MHz 12.288 60:40 40:60 PD, August 2010, Rev 4.0 8 WM8783 Production Data AUDIO INTERFACE TIMING LRCLK (input) BCLK (see note) ADCDAT (output) tDD Note - BCLK is generated internally to the WM8783, and is synchronised to LRCLK Figure 3 Audio Interface Timing Test Conditions AVDD = 3.3V, GND = 0V, TA = +25oC. PARAMETER SYMBOL MIN TYP MAX UNIT 20 ns Audio Interface Timing ADCDAT propagation delay from BCLK falling edge tDD Figure 4 Recommended LRCLK Transition Area for Optimum Performance It is recommended that for optimum performance the LRCLK transition occurs during the MCLK low, as shown in Figure 4 above. w PD, August 2010, Rev 4.0 9 WM8783 Production Data DEVICE DESCRIPTION INTRODUCTION The WM8783 is a low-cost ADC designed for set-top boxes and DVD applications. It is packaged in an 8-pin SOIC. The device comprises two analogue input pins, each accepting line signals up to 1Vrms. The signal path gain is fixed. The stereo hi-fi ADCs operate at sample rates from 8kHz up to 96kHz. A high pass filter is provided in the ADC path for removing DC offsets and suppressing low frequency noise. The digital audio interface supports the ADC output in stereo 24-bit I2S format. The device requires no configuration instructions and automatically selects the ADC sample rate according to the external master clock (MCLK) frequency. The WM8783 incorporates an internal voltage reference and LDO regulator for power-efficient operation from a single AVDD power supply. External clocking is required via the MCLK and LRCLK pins. A power on reset circuit ensures correct start-up and shut-down when AVDD is switched on or off. The WM8783 is held in reset when MCLK not present, offering a low-power standby state. ANALOGUE-TO-DIGITAL CONVERTER (ADC) The WM8783 has two analogue input pins, INL and INR. The maximum analogue input signal level varies with AVDD, but is typically 0dBV (1Vrms) when AVDD = 3.3V. This is suitable for single-ended connection to line level input signals. The WM8783 uses two 24-bit sigma-delta ADCs. The use of multi-bit feedback and high oversampling rates reduces the effects of jitter and high frequency noise. The sample rate is set automatically according to the external clocks connected to LRCLK and MCLK. Many common sample rates from 8kHz to 96kHz are supported, as described in the "Digital Audio Interface" section. Digital filters are also incorporated on the ADC output signal path to remove DC offsets and other unwanted noise. The cut-off frequency of the ADC high-pass filter varies with the ADC sample rate (fs), but is typically 4Hz when fs = 48kHz. Filter response plots for the ADC high-pass filter are shown in "Digital Filter Characteristics". DIGITAL AUDIO INTERFACE The digital audio interface is used for outputting ADC data from the WM8783. It uses three pins: ADCDAT - ADC data output LRCLK - Left / Right data alignment clock MCLK - Master clock The WM8783 operates as a Slave device only; LRCLK and MCLK must be provided as inputs. It is a requirement of the WM8783 digital audio interface that the bit rate of the ADCDAT data is 64fs only, where fs is the audio sample rate. Note that the Bit Clock (BCLK) associated with the digital audio interface is configured and generated automatically within the WM8783. This allows the ADCDAT to be synchronised to the BCLK in the host processor, even though the BCLK is not connected externally to the WM8783. w PD, August 2010, Rev 4.0 10 WM8783 Production Data The digital audio interface supports many common sample rates, as detailed in Table 1. The required MCLK frequency in each case is also noted. The WM8783 will automatically determine the MCLK / fs ratio according to the supplied LRCLK and MCLK inputs. Note that the BCLK frequency is 64 x fs in all cases. SAMPLE RATE MCLK MCLK RATIO 8kHz 2.048MHz 256 x fs 16kHz 4.096MHz 256 x fs 32kHz 8.192MHz 256 x fs 44.1kHz 11.2896MHz 256 x fs 48kHz 12.288MHz 256 x fs 88.2kHz 11.2896MHz 128 x fs 96kHz 12.288MHz 128 x fs Table 1 Digital Audio Interface Clocking The WM8783 supports 24-bit stereo operation in I2S digital audio format. In I2S mode, the MSB is available on the second rising edge of BCLK following a LRCLK transition, as illustrated in Figure 5. The other bits up to the LSB are then transmitted in order. Note that there are unused BCLK cycles between the LSB of one sample and the MSB of the next. Note that BCLK is generated internally and is not transmitted or received externally to the WM8783. Figure 5 I2S Digital Audio Interface format (assuming n-bit word length) w PD, August 2010, Rev 4.0 11 WM8783 Production Data DIGITAL FILTER CHARACTERISTICS PARAMETER TEST CONDITIONS MIN +/- 0.1dB 0 Passband TYP MAX UNIT 0.454 fs -6dB 0.5fs Passband Ripple +/- 0.1 Stopband dB 0.546s Stopband Attenuation f > 0.546 fs -60 Group Delay dB 16.5 / fs s TERMINOLOGY 1. Stop Band Attenuation (dB) - the degree to which the frequency spectrum is attenuated (outside audio band) 2. Pass-band Ripple - any variation of the frequency response in the pass-band region ADC FILTER RESPONSE 20 -2.2m -20 -40.01 dB -60.01 -80.01 -100 -120 -140 -160 -180 -200 0 17.64k 35.28k 52.92k 70.56k 88.2k 105.8k 123.5k 141.1k 158.8k 176.4k MAGNITUDE(dB) Figure 6 ADC Frequency Response up to 4 x fs (Sample rate, fs = 48kHz) w PD, August 2010, Rev 4.0 12 WM8783 Production Data 34.07m 28.12m 22.18m 16.23m 10.28m dB 4.333m -1.614m -7.561m -13.51m -19.46m -25.4m -31.35m 0 2k 3.999k 5.999k 7.999k 9.998k 12k 14k 16k 18k 20k MAGNITUDE(dB) Figure 7 ADC Pass Band Frequency Response up to fs/2 (Sample rate, fs = 48kHz) 0 -5 -10 -15 -20 -25 -30 0 5 10 15 20 Figure 8 ADC High Pass Filter Frequency Response (Sample rate, fs = 48kHz) w PD, August 2010, Rev 4.0 13 WM8783 Production Data APPLICATIONS INFORMATION RECOMMENDED EXTERNAL COMPONENTS AUDIO INPUT PATHS The WM8783 provides 2 analogue audio inputs. Each of these inputs is referenced to the internal DC reference, VMID. A DC blocking capacitor is required for each input pin. The choice of capacitor is determined by the filter that is formed between that capacitor and the input impedance of the input pin. The circuit is illustrated in Figure 9. Figure 9 Audio Input Path DC Blocking Capacitor The input impedance is noted in the "Electrical Characteristics". It is recommended that an input capacitor is selected such that the Fc cut-off frequency is less than 20Hz. It is recommended that a 1F capacitance is used for all WM8783 input connections. Tantalum electrolytic capacitors are particularly suitable as they offer high stability in a small package size. See Wolfson Applications Note WAN_0176 for further guidance on the choice of capacitor types. POWER SUPPLY DECOUPLING Electrical coupling exists particularly in digital logic systems where switching in one sub-system causes fluctuations on the power supply. This effect occurs because the inductance of the power supply acts in opposition to the changes in current flow that are caused by the logic switching. The resultant variations (or `spikes') in the power supply voltage can cause malfunctions and unintentional behavior in other components. A decoupling (or `bypass') capacitor can be used as an energy storage component which will provide power to the decoupled circuit for the duration of these power supply variations, protecting it from malfunctions that could otherwise arise. Coupling also occurs in a lower frequency form when ripple is present on the power supply rail caused by changes in the load current or by limitations of the power supply regulation method. In audio components such as the WM8783, these variations can alter the performance of the signal path, leading to degradation in signal quality. A decoupling (or `bypass') capacitor can be used to filter these effects, by presenting the ripple voltage with a low impedance path that does not affect the circuit to be decoupled. These coupling effects are addressed by placing a capacitor between the supply rail and the corresponding ground reference. In the case of systems comprising multiple power supply rails, decoupling should be provided on each rail. The recommended power supply decoupling capacitors for WM8783 are listed below in Table 2. POWER SUPPLY DECOUPLING CAPACITOR AVDD 4.7F ceramic VMIDC 4.7F ceramic Table 2 Power Supply Decoupling Capacitors All decoupling capacitors should be placed as close as possible to the WM8783 device. w PD, August 2010, Rev 4.0 14 WM8783 Production Data The VMIDC capacitor is not, technically, a decoupling capacitor. However, it does serve a similar purpose in filtering noise on the VMID reference. The connection between GND, the VMID decoupling capacitor and the main system ground should be made at a single point as close as possible to the GND ball of the WM8783. Due to the wide tolerance of many types of ceramic capacitors, care must be taken to ensure that the selected components provide the required capacitance across the required temperature and voltage ranges in the intended application. For most application the use of ceramic capacitors with capacitor dielectric X5R is recommended. See Wolfson Applications Note WAN_0176 for further guidance on the choice of capacitor types. RECOMMENDED EXTERNAL COMPONENTS DIAGRAM Figure 10 provides a summary of recommended external components for WM8783. Note that the actual requirements may differ according to the specific target application. AVDD MCLK 2 LRCLK 3 LRCLK AVDD MCLK 8 C1 4.7uF GND 4 GND C2 WM8783 4.7uF VMIDC INL INR 5 7 INL 6 INR ADCDAT 1 Figure 10 WM8783 Recommended External Components Diagram PCB LAYOUT CONSIDERATIONS Poor PCB layout will degrade the performance and be a contributory factor in EMI, ground bounce and resistive voltage losses. All external components should be placed as close to the WM8783 device as possible, with current loop areas kept as small as possible. w PD, August 2010, Rev 4.0 15 WM8783 Production Data PACKAGE DIMENSIONS D: 8 PIN SOIC 3.9mm Wide Body DM009.B B e 8 5 E 1 H L 4 D h x 45o A A1 -C- 0.10 (0.004) Symbols A A1 B C D e E h H L Dimensions (mm) MIN MAX 1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 4.80 5.00 1.27 BSC 3.80 4.00 0.25 0.50 5.80 6.20 0.40 1.27 8o 0o REF: SEATING PLANE C Dimensions (Inches) MIN MAX 0.0532 0.0688 0.0040 0.0098 0.0130 0.0200 0.0075 0.0098 0.1890 0.1968 0.050 BSC 0.1497 0.1574 0.0099 0.0196 0.2284 0.2440 0.0160 0.0500 0o 8o JEDEC.95, MS-012 NOTES: A. ALL LINEAR DIMENSIONS ARE IN MILLIMETERS (INCHES). B. THIS DRAWING IS SUBJECT TO CHANGE WITHOUT NOTICE. C. BODY DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSION, NOT TO EXCEED 0.25MM (0.010IN). D. MEETS JEDEC.95 MS-012, VARIATION = AA. REFER TO THIS SPECIFICATION FOR FURTHER DETAILS. w PD, August 2010, Rev 4.0 16 Production Data WM8783 IMPORTANT NOTICE Wolfson Microelectronics plc ("Wolfson") products and services are sold subject to Wolfson's terms and conditions of sale, delivery and payment supplied at the time of order acknowledgement. Wolfson warrants performance of its products to the specifications in effect at the date of shipment. Wolfson reserves the right to make changes to its products and specifications or to discontinue any product or service without notice. Customers should therefore obtain the latest version of relevant information from Wolfson to verify that the information is current. Testing and other quality control techniques are utilised to the extent Wolfson deems necessary to support its warranty. Specific testing of all parameters of each device is not necessarily performed unless required by law or regulation. In order to minimise risks associated with customer applications, the customer must use adequate design and operating safeguards to minimise inherent or procedural hazards. Wolfson is not liable for applications assistance or customer product design. The customer is solely responsible for its selection and use of Wolfson products. Wolfson is not liable for such selection or use nor for use of any circuitry other than circuitry entirely embodied in a Wolfson product. Wolfson's products are not intended for use in life support systems, appliances, nuclear systems or systems where malfunction can reasonably be expected to result in personal injury, death or severe property or environmental damage. Any use of products by the customer for such purposes is at the customer's own risk. Wolfson does not grant any licence (express or implied) under any patent right, copyright, mask work right or other intellectual property right of Wolfson covering or relating to any combination, machine, or process in which its products or services might be or are used. Any provision or publication of any third party's products or services does not constitute Wolfson's approval, licence, warranty or endorsement thereof. Any third party trade marks contained in this document belong to the respective third party owner. Reproduction of information from Wolfson datasheets is permissible only if reproduction is without alteration and is accompanied by all associated copyright, proprietary and other notices (including this notice) and conditions. Wolfson is not liable for any unauthorised alteration of such information or for any reliance placed thereon. Any representations made, warranties given, and/or liabilities accepted by any person which differ from those contained in this datasheet or in Wolfson's standard terms and conditions of sale, delivery and payment are made, given and/or accepted at that person's own risk. Wolfson is not liable for any such representations, warranties or liabilities or for any reliance placed thereon by any person. ADDRESS: Wolfson Microelectronics plc 26 Westfield Road Edinburgh EH11 2QB United Kingdom Tel :: +44 (0)131 272 7000 Fax :: +44 (0)131 272 7001 Email :: sales@wolfsonmicro.com w PD, August 2010, Rev 4.0 17