MCP73213 Dual-Cell Li-Ion / Li-Polymer Battery Charge Management Controller with Input Overvoltage Protection Features Description * Complete Linear Charge Management Controller: - Integrated Input Overvoltage Protection - Integrated Pass Transistor - Integrated Current Sense - Integrated Reverse Discharge Protection * Constant Current / Constant Voltage Operation with Thermal Regulation * 4.15V Undervoltage Lockout (UVLO) * 13V Input Overvoltage Protection * High Accuracy Preset Voltage Regulation Through Full Temperature Range (-5C to +55C): - + 0.6% * Battery Charge Voltage Options: - 8.20V, 8.40V, 8.7V or 8.8V * Resistor Programmable Fast Charge Current: - 130 mA - 1100 mA * Preconditioning of Deeply Depleted Cells: - Available Options: 10% or Disable * Integrated Precondition Timer: - 32 Minutes or Disable * Automatic End-of-Charge Control: - Selectable Minimum Current Ratio: 5%, 7.5%, 10% or 20% - Elapse Safety Timer: 4 HR, 6 HR, 8 HR or Disable * Automatic Recharge: - Available Options: 95% or Disable * Factory Preset Charge Status Output: - On/Off or Flashing * Soft Start * Temperature Range: -40C to +85C * Packaging: DFN-10 (3 mm x 3 mm) The MCP73213 is a highly integrated Li-Ion battery charge management controller for use in space-limited and cost-sensitive applications. The MCP73213 provides specific charge algorithms for dual-cell Li-Ion / Li-Polymer batteries to achieve optimal capacity and safety in the shortest charging time possible. Along with its small physical size, the low number of external components makes the MCP73213 ideally suitable for portable applications. The absolute maximum voltage, up to 18V, allows the use of MCP73213 in harsh environments, such as low cost wall wart or voltage spikes from plug/unplug. The MCP73213 employs a constant current / constant voltage charge algorithm. The various charging voltage regulations provide design engineers flexibility to use in different applications. The fast charge, constant current value is set with one external resistor from 130 mA to 1100 mA. The MCP73213 limits the charge current based on die temperature during high power or high ambient conditions. This thermal regulation optimizes the charge cycle time while maintaining device reliability. The PROG pin of the MCP73213 also serves as enable pin. When high impedance is applied, the MCP73213 will be in standby mode. The MCP73213 is fully specified over the ambient temperature range of -40C to +85C. The MCP73213 is available in a 10 lead, DFN package. Package Types (Top View) MCP73213 3x3 DFN * VDD 1 VDD 2 VBAT 3 Applications * * * * * * * Digital Camcorders Portable Media Players Ultra Mobile Personal Computers Netbook Computers Handheld Devices Walkie-Talkie Low-Cost 2-Cell Li-Ion/Li-Poly Chargers / Cradles (c) 2009 Microchip Technology Inc. VBAT 4 NC 5 10 PROG EP 11 9 VSS 8 VSS 7 STAT 6 NC * Includes Exposed Thermal Pad (EP); see Table 3-1. DS22190B-page 1 MCP73213 Typical Application MCP73213 Typical Application 1 Ac-dc-Adapter 2 CIN RLED 7 VDD VBAT VBAT VDD + 4 COUT STAT PROG 5 NC VSS 6 NC TABLE 1: 3 VSS 2-Cell Li-Ion Battery 10 9 RPROG 8 - AVAILABLE FACTORY PRESET OPTIONS Precondition Timer Elapse Timer End-ofCharge Control Automatic Recharge Output Status 66.5% / 71.5% Disable / 32 Minimum Disable / 4 HR / 6 HR / 8 HR 5% / 7.5% / 10% / 20% No / Yes Type 1 / Type 2 Disable / 10% 66.5% / 71.5% Disable / 32 Minimum Disable / 4 HR / 6 HR / 8 HR 5% / 7.5% / 10% / 20% No / Yes Type 1 / Type 2 13V Disable / 10% 66.5% / 71.5% Disable / 32 Minimum Disable / 4 HR / 6 HR / 8 HR 5% / 7.5% / 10% / 20% No / Yes Type 1 / Type 2 13V Disable / 10% 66.5% / 71.5% Disable / 32 Minimum Disable / 4 HR / 6 HR / 8 HR 5% / 7.5% / 10% / 20% No / Yes Type 1 / Type 2 Charge Voltage OVP Preconditioning Charge Current Preconditioning Threshold 8.2V 13V Disable / 10% 8.4V 13V 8.7V 8.8V Note 1: 2: 3: 4: 5: 6: IREG: Regulated fast charge current. VREG: Regulated charge voltage. IPREG/IREG: Preconditioning charge current; ratio of regulated fast charge current. ITERM/IREG: End-of-Charge control; ratio of regulated fast charge current. VRTH/VREG: Recharge threshold; ratio of regulated battery voltage. VPTH/VREG: Preconditioning threshold voltage. TABLE 2: STANDARD SAMPLE OPTIONS Part Number VREG OVP IPREG/IREG Pre-charge Timer Elapse Timer MCP73213-B6S/MF 8.20V 13V 10% 32 Min. 6 HR 10% 95% 71.5% Type 1 MCP73213-A6S/MF 8.40V 13V 10% 32 Min. 6 HR 10% 95% 71.5% Type 1 Note 1: ITERM/IREG VRTH/VREG VPTH/VREG Output Status Customers should contact their distributor, representatives or field application engineer (FAE) for support and sample. Local sales offices are also available to help customers. A listing of sales offices and locations is included in the back of this document. Technical support is available through the web site at: http//support.microchip.com DS22190B-page 2 (c) 2009 Microchip Technology Inc. MCP73213 Functional Block Diagram VOREG DIRECTION CONTROL VBAT VDD + CURRENT LIMIT - VREF PROG + REFERENCE, V REF (1.21V) BIAS, UVLO AND SHDN VOREG CA - + UVLO - - PRECONDITION + TERM + STAT CHARGE CONTROL, TIMER AND STATUS LOGIC CHARGE + VA - VSS 13V + VDD Input OverVP + Thermal Regulation (c) 2009 Microchip Technology Inc. TSD 95% VREG + 110C VBAT *Recharge *Only available on selected options DS22190B-page 3 MCP73213 NOTES: DS22190B-page 4 (c) 2009 Microchip Technology Inc. MCP73213 1.0 ELECTRICAL CHARACTERISTICS Notice: Stresses above those listed under "Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. Absolute Maximum Ratings VDD ................................................................................18.0V VPROG ..............................................................................6.0V All Inputs and Outputs w.r.t. VSS ............... -0.3 to (VDD+0.3)V Maximum Junction Temperature, TJ ............ Internally Limited Storage temperature .....................................-65C to +150C ESD protection on all pins Human Body Model (1.5 k in Series with 100 pF)....... 4 kV Machine Model (200 pF, No Series Resistance) .............300V DC CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, all limits apply for VDD= [VREG(Typical) + 0.3V] to 12V, TA = -40C to +85C. Typical values are at +25C, VDD = [VREG (Typical) + 1.0V] Parameters Sym Min Typ Max Units Conditions Input Voltage Range VDD 4 -- 16 V Operating Supply Voltage VDD 4.2 -- 13 V Supply Current ISS -- 4 5.5 A Shutdown (VDD < VBAT - 150 mV) -- 700 1500 A Charging -- 50 125 A Standby (PROG Floating) -- 50 150 A Charge Complete; No Battery; VDD < VSTOP -- 0.5 2 A Standby (PROG Floating) -- 0.5 2 A Shutdown (VDD < VBAT, or VDD < VSTOP) 10 17 A Charge Complete; VDD is present Supply Input Battery Discharge Current Output Reverse Leakage Current IDISCHARGE Undervoltage Lockout UVLO Start Threshold VSTART 4.10 4.15 4.25 V UVLO Stop Threshold VSTOP 4.00 4.05 4.10 V UVLO Hysteresis VHYS -- 100 -- mV VOVP 12.8 13 13.2 V VOVPHYS -- 150 -- mV 8.15 8.20 8.25 V TA= -5C to +55C 8.35 8.40 8.45 V VDD = [VREG(Typical)+1V] 8.65 8.70 8.75 V IOUT = 50 mA Overvoltage Protection OVP Start Threshold OVP Hysteresis Voltage Regulation (Constant Voltage Mode) Regulated Output Voltage Options VREG 8.75 8.80 8.85 V VRTOL -0.6 -- 0.6 % Line Regulation |(VBAT/VBAT)/ VDD| -- 0.05 0.20 %/V Load Regulation |VBAT/VBAT| -- 0.05 0.20 % IOUT = 50 mA - 150 mA VDD = [VREG(Typical)+1V] PSRR -- -46 -- dB IOUT = 20 mA, 10 Hz to 1 kHz -- -30 -- dB IOUT = 20 mA, 10 Hz to 10 kHz Output Voltage Tolerance Supply Ripple Attenuation Note 1: VDD = [VREG(Typical)+1V] to 12V IOUT = 50 mA Not production tested. Ensured by design. (c) 2009 Microchip Technology Inc. DS22190B-page 5 MCP73213 DC CHARACTERISTICS (CONTINUED) Electrical Specifications: Unless otherwise indicated, all limits apply for VDD= [VREG(Typical) + 0.3V] to 12V, TA = -40C to +85C. Typical values are at +25C, VDD = [VREG (Typical) + 1.0V] Parameters Sym Min Typ Max Units Conditions BSP Start Threshold VSHORT -- 3.4 -- V BSP Hysteresis VBSPHYS -- 150 -- mV ISHORT -- 25 -- mA -- 1100 mA TA = -5C to +55C Battery Short Protection BSP Regulation Current Current Regulation (Fast Charge, Constant-Current Mode) Fast Charge Current Regulation IREG 130 117 130 143 mA PROG = 10 k 900 1000 1100 mA PROG = 1.1 k Preconditioning Current Regulation (Trickle Charge Constant Current Mode) Precondition Current Ratio IPREG / IREG -- 10 -- % PROG = 1 k to 10 k TA=-5C to +55C -- 100 -- % No Preconditioning Precondition Voltage Threshold Ratio VPTH / VREG 64 66.5 69 % VBAT Low-to-High 69 71.5 74 % VPHYS -- 100 -- mV ITERM / IREG 3.7 5 6.3 % 5.6 7.5 9.4 PROG = 1 k to 10 k TA=-5C to +55C 7.5 10 12.5 15 20 25 93 95.0 97 % -- 0 -- % VBAT High-to-Low No Automatic Recharge RDSON -- 350 -- m Sink Current ISINK -- 20 35 mA Low Output Voltage VOL -- 0.2 0.5 V ISINK = 4 mA Input Leakage Current ILK -- 0.001 1 A High Impedance, VDD on pin Precondition Hysteresis VBAT High-to-Low (Note 1) Charge Termination Charge Termination Current Ratio Automatic Recharge Recharge Voltage Threshold Ratio VRTH / VREG Pass Transistor ON-Resistance ON-Resistance VDD = 4.5V, TJ = 105C (Note 1) Status Indicator - STAT PROG Input Charge Impedance Range RPROG 1 -- 22 k Shutdown Impedance RPROG -- 200 -- k Automatic Power Down Entry Threshold VPDENTRY VBAT + 10 mV VBAT + 50 mV -- V VDD Falling Automatic Power Down Exit Threshold VPDEXIT -- VBAT + 150 mV VBAT + 250 mV V VDD Rising Die Temperature TSD -- 150 -- C Die Temperature Hysteresis TSDHYS -- 10 -- C Impedance for Shutdown Automatic Power Down Thermal Shutdown Note 1: Not production tested. Ensured by design. DS22190B-page 6 (c) 2009 Microchip Technology Inc. MCP73213 AC CHARACTERISTICS Electrical Specifications: Unless otherwise specified, all limits apply for VDD= [VREG(Typical)+0.3V] to 12V, TA=-40C to +85C. Typical values are at +25C, VDD= [VREG(Typical)+1.0V] Parameters Sym Min Typ Max Units Conditions Elapsed Timer Elapsed Timer Period tELAPSED -- 0 -- Hours 3.6 4.0 4.4 Hours 5.4 6.0 6.6 Hours 7.2 8.0 8.8 Hours Timer Disabled Preconditioning Timer Preconditioning Timer Period tPRECHG -- 0 -- Hours 0.4 0.5 0.6 Hours s Disabled Timer Status Indicator Status Output turn-off tOFF -- -- 500 Status Output turn-on, tON -- -- 500 Note 1: ISINK = 1 mA to 0 mA (Note 1) ISINK = 0 mA to 1 mA (Note 1) Not production tested. Ensured by design. TEMPERATURE SPECIFICATIONS Electrical Specifications: Unless otherwise indicated, all limits apply for VDD = [VREG (Typical) + 0.3V] to 6V. Typical values are at +25C, VDD = [VREG (Typical) + 1.0V] Parameters Sym Min Typ Max Units TA -40 -- +85 C Operating Temperature Range TJ -40 -- +125 C Storage Temperature Range TA -65 -- +150 C JA -- 43 -- C/W Conditions Temperature Ranges Specified Temperature Range Thermal Package Resistances Thermal Resistance, DFN-10 (3x3) (c) 2009 Microchip Technology Inc. 4-Layer JC51-7 Standard Board, Natural Convection DS22190B-page 7 MCP73213 NOTES: DS22190B-page 8 (c) 2009 Microchip Technology Inc. MCP73213 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. Battery Regulation Voltage (V) Battery Regulation Voltage (V) Note: Unless otherwise indicated, VDD = [VREG(Typical) + 1V], IOUT = 50 mA and TA= +25C, Constant-voltage mode. 8.24 8.23 8.22 8.21 8.20 8.19 VBAT = 8.2V ILOAD = 150 mA TA = +25C 8.18 8.17 8.16 8.4 9.0 9.6 10.2 10.8 11.4 12.0 8.24 8.23 8.22 8.21 8.20 8.19 VBAT = 8.2V VDD = 9.2V ILOAD = 150 mA 8.18 8.17 8.16 -5.0 5.0 Supply Voltage (V) 25.0 35.0 45.0 55.0 FIGURE 2-4: Battery Regulation Voltage (VBAT) vs. Ambient Temperature (TA). 8.24 1200 8.23 Charge Current (mA) Battery Regulation Voltage (V) FIGURE 2-1: Battery Regulation Voltage (VBAT) vs. Supply Voltage (VDD). 8.22 8.21 8.20 8.19 VBAT = 8.2V ILOAD = 50 mA TA = +25C 8.18 8.17 8.16 VBAT = 8.2V VDD = 9.2V TA = +25C 1000 800 600 400 200 0 8.4 9.0 9.6 10.2 10.8 11.4 12.0 1 3 Supply Voltage (V) Charge Current (mA) 8.23 8.22 8.21 8.20 8.19 VBAT = 8.2V VDD = 9.2V ILOAD = 50 mA 8.17 8.16 -5 5 15 25 35 45 55 Ambient Temperature (C) FIGURE 2-3: Battery Regulation Voltage (VBAT) vs. Ambient Temperature (TA). (c) 2009 Microchip Technology Inc. 7 9 11 13 15 17 19 FIGURE 2-5: Charge Current (IOUT) vs. Programming Resistor (RPROG). 8.24 8.18 5 Programming Resistor (k) FIGURE 2-2: Battery Regulation Voltage (VBAT) vs. Supply Voltage (VDD). Battery Regulation Voltage (V) 15.0 Ambient Temperature (C) 900 880 860 840 820 800 780 760 740 720 700 R PROG = 1.3 k TA = +25C 8.4 9.0 9.6 10.2 10.8 11.4 12.0 Supply Voltage (V) FIGURE 2-6: Charge Current (IOUT) vs. Supply Voltage (VDD). DS22190B-page 9 MCP73213 TYPICAL PERFORMANCE CURVES (CONTINUED) 600 160 154 148 142 136 130 124 118 112 106 100 Charge Current (mA) Charge Current (mA) Note: Unless otherwise indicated, VDD = [VREG(Typical) + 1V], IOUT = 10 mA and TA= +25C, Constant-voltage mode. RPROG = 10 k TA = +25C 8.4 9.0 VBAT = 8.2V RPROG = 2 k 590 VDD = 12V 580 VDD = 11V 570 560 VDD = 9.2V VDD = 8.5V 9.6 10.2 10.8 11.4 550 12.0 -5 0 5 Supply Voltage (V) Ambient Temperature (C) RPROG = 5 k TA = +25C 8.4 9.0 FIGURE 2-10: Charge Current (IOUT) vs. Ambient Temperature (TA). BSP Regulation Current (mA) Charge Current (mA) FIGURE 2-7: Charge Current (IOUT) vs. Programming Resistor (RPROG). 300 290 280 270 260 250 240 230 220 210 200 9.6 10.2 10.8 11.4 12.0 VDD = 12V VDD = 11V VDD = 9.2V VDD = 8.5V 5 10 15 20 25 30 35 40 45 50 55 Ambient Temperature (C) FIGURE 2-9: Charge Current (IOUT) vs. Ambient Temperature (TA). DS22190B-page 10 22 18 14 VDD = 9.2V 10 5 15 25 35 45 55 65 75 85 FIGURE 2-11: Battery Short Protection Regulation Current (ISHORT) vs. Ambient Temperature (TA). Discharge Current (uA) Charge Current (mA) VBAT = 8.2V RPROG = 20 k 0 26 Ambient Temperature (C) FIGURE 2-8: Charge Current (IOUT) vs. Programming Resistor (RPROG). -5 30 -45 -35 -25 -15 -5 Supply Voltage (V) 90 87 84 81 78 75 72 69 66 63 60 10 15 20 25 30 35 40 45 50 55 9.0 8.0 7.0 6.0 5.0 End of Charge 4.0 3.0 2.0 VDD < VBAT 1.0 0.0 VDD < VSTOP -1.0 -5.0 5.0 15.0 25.0 35.0 45.0 55.0 Ambient Temperature (C) FIGURE 2-12: Output Leakage Current (IDISCHARGE) vs. Ambient Temperature (TA). (c) 2009 Microchip Technology Inc. MCP73213 TYPICAL PERFORMANCE CURVES (CONTINUED) Battery Voltage Accuracy (%) Note: Unless otherwise indicated, VDD = [VREG(Typical) + 1V], IOUT = 10 mA and TA= +25C, Constant-voltage mode. 0.5 0.3 Output Current 0.1 -0.1 Battery Voltage Input Voltage VBAT = 8.2V ILOAD = 150 mA TA = +25C -0.3 -0.5 8.4 9.0 9.6 10.2 10.8 11.4 12.0 Supply Voltage (V) FIGURE 2-13: Battery Voltage Accuracy (VRTOL) vs. Supply Voltage (VDD). FIGURE 2-16: Complete Charge Cycle (875 mAh Li-Ion Battery). Source Voltage (V) Output Ripple (V) Output Ripple (V) Output Current (mA) 10 9 8 7 6 5 4 3 1.2 1.1 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 Thermal Foldback VDD = 9V RPROG = 1.5 k 875 mAh Li-Ion Battery 2 1 0 0 10 20 FIGURE 2-15: Protection. 30 40 50 60 Time (Minutes) 70 80 Input Overvoltage (c) 2009 Microchip Technology Inc. Supply Current (A) Battery Voltage (V) FIGURE 2-14: Load Transient Response (ILOAD = 50 mA/Div, Output: 100 mV/Div, Time: 100 s/Div). FIGURE 2-17: Line Transient Response (ILOAD = 10 mA) (100 s/Div). Source Voltage (V) Output Ripple (V) 90 FIGURE 2-18: Line Transient Response (ILOAD = 100 mA) (100 s/Div). DS22190B-page 11 MCP73213 NOTES: DS22190B-page 12 (c) 2009 Microchip Technology Inc. MCP73213 3.0 PIN DESCRIPTION The descriptions of the pins are listed in Table 3-1. TABLE 3-1: MCP73213 DFN-10 3.1 PIN FUNCTION TABLES Symbol I/O Description 1, 2 VDD I 3, 4 VBAT I/O Battery Charge Control Output Battery Management Input Supply 5, 6 NC -- No Connection 7 STAT O Battery Charge Status Output 8, 9 VSS -- Battery Management 0V Reference 10 PROG I/O Battery Charge Current Regulation Program and Charge Control Enable 11 EP -- Exposed Pad Battery Management Input Supply (VDD) A supply voltage of [VREG (Typical) + 0.3V] to 13.0V is recommended. Bypass to VSS with a minimum of 1 F. The VDD pin is rated 18V absolute maximum to prevent suddenly rise of input voltage from spikes or low cost ac-dc wall adapter. 3.5 Battery Management 0V Reference (VSS) Connect to the negative terminal of the battery and input supply. 3.6 Current Regulation Set (PROG) Connect to the positive terminal of the battery. Bypass to VSS with a minimum of 1 F to ensure loop stability when the battery is disconnected. The fast charge current is set by placing a resistor from PROG to VSS during constant current (CC) mode. PROG pin also serves as charge control enable. When a typical 200 k impedance is applied to PROG pin, the MCP73213 is disabled until the high-impedance is removed. Refer to Section 5.5 "Constant Current Mode - Fast Charge" for details. 3.3 3.7 3.2 Battery Charge Control Output (VBAT) No Connect (NC) No connect. 3.4 Status Output (STAT) STAT is an open-drain logic output for connection to an LED for charge status indication in standalone applications. Alternatively, a pull-up resistor can be applied for interfacing to a host microcontroller. Refer to Table 5-1 for a summary of the status output during a charge cycle. (c) 2009 Microchip Technology Inc. Exposed Pad (EP) The Exposed Thermal Pad (EP) shall be connected to the exposed copper area on the Printed Circuit Board (PCB) for the thermal enhancement. Additional vias on the copper area under the MCP73213 device can improve the performance of heat dissipation and simplify the assembly process. DS22190B-page 13 MCP73213 NOTES: DS22190B-page 14 (c) 2009 Microchip Technology Inc. MCP73213 4.0 DEVICE OVERVIEW The MCP73213 are simple, but fully integrated linear charge management controllers. Figure 4-1 depicts the operational flow algorithm. SHUTDOWN MODE VDD < VUVLO VDD < VPD or PROG > 200 k STAT = HI-Z VBAT < VPTH VDD < VOVP PRECONDITIONING MODE Charge Current = IPREG STAT = LOW Timer Reset Timer Enable Timer Expired TIMER FAULT No Charge Current STAT = Flashing (Op.1) STAT = Hi-Z (Op.2) Timer Suspended VDD > VOVP VDD > VOVP VBAT > VPTH VBAT > VPTH FAST CHARGE MODE Charge Current = IREG STAT = LOW Timer Reset Timer Enabled OVERVOLTAGE PROTECTION No Charge Current STAT = Hi-Z Timer Suspended VDD < VOVP VDD > VOVP VDD < VOVP VBAT = VREG Timer Expired VBAT < VRTH TIMER FAULT No Charge Current STAT = Flashing (Op.1) STAT = Hi-Z (Op.2) Timer Suspended CONSTANT VOLTAGE MODE Charge Voltage = VREG STAT = LOW VBAT < ITERM Die Temperature < TSDHYS Charge Mode Resume CHARGE COMPLETE MODE No Charge Current STAT = HI-Z Timer Reset Die Temperature > TSD VBAT < VSHORT TEMPERATURE FAULT No Charge Current STAT = Flashing (Op.1) STAT = Hi-Z (Op.2) Timer Suspended FIGURE 4-1: VBAT > VSHORT Charge Mode Resume BATTERY SHORT PROTECTION Charge Current = ISHORT STAT = Flashing (Op.1) STAT = Hi-Z (Op.2) Timer Suspended The MCP73213 Flow Chart. (c) 2009 Microchip Technology Inc. DS22190B-page 15 MCP73213 NOTES: DS22190B-page 16 (c) 2009 Microchip Technology Inc. MCP73213 5.0 DETAILED DESCRIPTION 5.3.2 5.1 Undervoltage Lockout (UVLO) The battery charge control output is the drain terminal of an internal P-channel MOSFET. The MCP73213 provides constant current and voltage regulation to the battery pack by controlling this MOSFET in the linear region. The battery charge control output should be connected to the positive terminal of the battery pack. An internal undervoltage lockout (UVLO) circuit monitors the input voltage and keeps the charger in shutdown mode until the input supply rises above the UVLO threshold. In the event a battery is present when the input power is applied, the input supply must rise approximately 150 mV above the battery voltage before the MCP73213 device becomes operational. The UVLO circuit places the device in shutdown mode if the input supply falls to approximately 150 mV above the battery voltage.The UVLO circuit is always active. At any time, the input supply is below the UVLO threshold or approximately 150 mV of the voltage at the VBAT pin, the MCP73213 device is placed in a shutdown mode. 5.2 Overvoltage Protection (OVP) An internal overvoltage protection (OVP) circuit monitors the input voltage and keeps the charger in shutdown mode when the input supply rises above the typical 13V, OVP threshold. The hysteresis of OVP is approximately 150 mV for the MCP73213 device. The MCP73213 device is operational between UVLO and OVP threshold. The OVP circuit is also recognized as overvoltage lock out (OVLO). 5.3 Charge Qualification When the input power is applied, the input supply must rise 150 mV above the battery voltage before the MCP73213 becomes operational. The automatic power down circuit places the device in a shutdown mode if the input supply falls to within +50 mV of the battery voltage. The automatic circuit is always active. At any time the input supply is within +50 mV of the voltage at the VBAT pin, the MCP73213 is placed in a shutdown mode. For a charge cycle to begin, the automatic power down conditions must be met and the charge enable input must be above the input high threshold. 5.3.1 BATTERY MANAGEMENT INPUT SUPPLY (VDD) The VDD input is the input supply to the MCP73213. The MCP73213 automatically enters a Power-down mode if the voltage on the VDD input falls to within +50 mV of the battery voltage. This feature prevents draining the battery pack when the VDD supply is not present. (c) 2009 Microchip Technology Inc. 5.3.3 BATTERY CHARGE CONTROL OUTPUT (VBAT) BATTERY DETECTION The MCP73213 detects the battery presence with charging of the output capacitor. The charge flow will initiate when the voltage on VBAT is pulled below the VRECHARGE threshold. Refer to Section 1.0 "Electrical Characteristics" for VRECHARGE values. The value will be the same for non-rechargeable device. When VBAT > VREG + Hysteresis, the charge will be suspended or not start, depending on the condition to prevent over charge that may occur. 5.4 Preconditioning If the voltage at the VBAT pin is less than the preconditioning threshold, the MCP73213 device enters a preconditioning mode. The preconditioning threshold is factory set. Refer to Section 1.0 "Electrical Characteristics" for preconditioning threshold options. In this mode, the MCP73213 device supplies 10% of the fast charge current (established with the value of the resistor connected to the PROG pin) to the battery. When the voltage at the VBAT pin rises above the preconditioning threshold, the MCP73213 device enters the constant current (fast charge) mode. Note: 5.4.1 The MCP73213 device also offers options with no preconditioning. TIMER EXPIRED DURING PRECONDITIONING MODE If the internal timer expires before the voltage threshold is reached for fast charge mode, a timer fault is indicated and the charge cycle terminates. The MCP73213 device remains in this condition until the battery is removed or input power is cycled. If the battery is removed, the MCP73213 device enters the Stand-by mode where it remains until a battery is reinserted. Note: The typical preconditioning timer for MCP73213 is 32 minutes. The MCP73213 also offers options with no preconditioning timer. DS22190B-page 17 MCP73213 5.5 Constant Current Mode - Fast Charge During the constant current mode, the programmed charge current is supplied to the battery or load. The charge current is established using a single resistor from PROG to VSS. The program resistor and the charge current are calculated using the following equation: EQUATION 5-1: I REG = 1104 x R PROG - 0.93 Where: RPROG = kilo-ohms (k) IREG = milliampere (mA) 5.5.1 5.7 Where: = kilo-ohms (k) IREG = milliampere (mA) Table 5-1 provides commonly seen E96 (1%) and E24 (5%) resistors for various charge current to reduce design time. TABLE 5-1: RESISTOR LOOKUP TABLE Charge Recommended Recommended Current (mA) E96 Resistor () E24 Resistor () 130 10k 10k 150 8.45k 8.20k 200 6.20k 6.20k 250 4.99k 5.10k 300 4.02k 3.90k 350 3.40k 3.30k 400 3.00k 3.00k 450 2.61k 2.70k 500 2.32k 2.37k 550 2.10k 2.20k 600 1.91k 2.00k 650 1.78k 1.80k 700 1.62k 1.60k 750 1.50k 1.50k 800 1.40k 1.50k 850 1.33k 1.30k 900 1.24k 1.20k 950 1.18k 1.20k 1000 1.10k 1.10k 1100 1.00k 1.00k DS22190B-page 18 Constant Voltage Mode When the voltage at the VBAT pin reaches the regulation voltage, VREG, constant voltage regulation begins. The regulation voltage is factory set to 8.2V, 8.4V, 8.7V or 8.8V with a tolerance of 0.5%. I REG log ---------- 1104 ( - 0.93 ) RPROG TIMER EXPIRED DURING CONSTANT CURRENT - FAST CHARGE MODE If the internal timer expires before the recharge voltage threshold is reached, a timer fault is indicated and the charge cycle terminates. The MCP73213 device remains in this condition until the battery is removed. If the battery is removed or input power is cycled, the MCP73213 device enters the Stand-by mode where it remains until a battery is reinserted. 5.6 EQUATION 5-2: R PROG = 10 Constant current mode is maintained until the voltage at the VBAT pin reaches the regulation voltage, VREG. When constant current mode is invoked, the internal timer is reset. Charge Termination The charge cycle is terminated when, during constant voltage mode, the average charge current diminishes below a threshold established with the value of 5%, 7.5%, 10% or 20% of fast charge current or internal timer has expired. A 1 ms filter time on the termination comparator ensures that transient load conditions do not result in premature charge cycle termination. The timer period is factory set and can be disabled. Refer to Section 1.0 "Electrical Characteristics" for timer period options. 5.8 Automatic Recharge The MCP73213 device continuously monitors the voltage at the VBAT pin in the charge complete mode. If the voltage drops below the recharge threshold, another charge cycle begins and current is once again supplied to the battery or load. The recharge threshold is factory set. Refer to Section 1.0 "Electrical Characteristics" for recharge threshold options. Note: The MCP73213 also offers options with no automatic recharge. For the MCP73213 device with no recharge option, the MCP73213 will go into standby mode when termination condition is met. The charge will not restart until following conditions have been met: * Battery is removed from the system and inserted again * VDD is removed and plugged in again * RPROG is disconnected (or high impedance) and reconnected (c) 2009 Microchip Technology Inc. MCP73213 5.9 Thermal Regulation The MCP73213 shall limit the charge current based on the die temperature. The thermal regulation optimizes the charge cycle time while maintaining device reliability. Figure 5-1 depicts the thermal regulation for the MCP73213 device. Refer to Section 1.0 "Electrical Characteristics" for thermal package resistances and Section 6.1.1.2 "Thermal Considerations" for calculating power dissipation. TABLE 5-2: STATUS OUTPUTS CHARGE CYCLE STATE Shutdown Hi-Z Standby Hi-Z Preconditioning L Constant Current Fast Charge L Constant Voltage . Charge Complete - Standby Fast Charge Current (mA) 150 1.6 second 50% D.C. Flashing (Type 2) Hi-Z (Type 1) Timer Fault 1.6 second 50% D.C. Flashing (Type 2) Hi-Z (Type 1) Preconditioning Timer Fault 1.6 second 50% D.C. Flashing (Type 2) Hi-Z (Type 1) 60 VDD = 9.1V RPROG = 10 k 30 0 25 40 FIGURE 5-1: 5.10 55 70 85 100 115 130 145 160 Junction Temperature (C) Thermal Regulation. Thermal Shutdown The MCP73213 suspends charge if the die temperature exceeds +150C. Charging will resume when the die temperature has cooled by approximately 10C. The thermal shutdown is a secondary safety feature in the event that there is a failure within the thermal regulation circuitry. 5.11 Status Indicator L Hi-Z Temperature Fault 120 90 STAT 5.12 Battery Short Protection Once a single-cell Li-Ion battery is detected, an internal battery short protection (BSP) circuit starts monitoring the battery voltage. When VBAT falls below a typical 1.7V battery short protection threshold voltage, the charging behavior is postponed. 25 mA (typical) detection current is supplied for recovering from battery short condition. Preconditioning mode resumes when VBAT raises above battery short protection threshold. The battery voltage must rise approximately 150 mV above the battery short protection voltage before the MCP73213 device become operational. The charge status outputs are open-drain outputs with two different states: Low (L), and High Impedance (Hi-Z). The charge status outputs can be used to illuminate LEDs. Optionally, the charge status outputs can be used as an interface to a host microcontroller. Table 5-2 summarize the state of the status outputs during a charge cycle. (c) 2009 Microchip Technology Inc. DS22190B-page 19 MCP73213 NOTES: DS22190B-page 20 (c) 2009 Microchip Technology Inc. MCP73213 6.0 APPLICATIONS The MCP73213 is designed to operate in conjunction with a host microcontroller or in stand-alone applications. The MCP73213 provides the preferred charge algorithm for dual Lithium-Ion or Lithium-Polymer cells Constant-current followed by Constant-voltage. Figure 6-1 depicts a typical stand-alone application circuit, while Figure 6-2 depicts the accompanying charge profile. MCP73213 Typical Application 1 Ac-dc-Adapter 2 CIN RLED 7 VDD VDD STAT 5 NC 6 NC 10 9 8 7 6 5 4 3 1.2 1.1 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 VDD = 9V RPROG = 1.5 k 875 mAh Li-Ion Battery 0 10 + 4 COUT PROG VSS VSS 2-Cell Li-Ion Battery 10 9 8 RPROG - Typical Application Circuit. Thermal Foldback 2 1 0 VBAT 3 20 30 40 50 60 Time (Minutes) 70 80 Supply Current (A) Battery Voltage (V) FIGURE 6-1: VBAT 90 FIGURE 6-2: Typical Charge Profile (875 mAh Li-Ion Battery). (c) 2009 Microchip Technology Inc. DS22190B-page 21 MCP73213 6.1 Application Circuit Design Due to the low efficiency of linear charging, the most important factors are thermal design and cost, which are a direct function of the input voltage, output current and thermal impedance between the battery charger and the ambient cooling air. The worst-case situation is when the device has transitioned from the Preconditioning mode to the Constant-current mode. In this situation, the battery charger has to dissipate the maximum power. A trade-off must be made between the charge current, cost and thermal requirements of the charger. 6.1.1 COMPONENT SELECTION Selection of the external components in Figure 6-1 is crucial to the integrity and reliability of the charging system. The following discussion is intended as a guide for the component selection process. 6.1.1.1 Charge Current The preferred fast charge current for Li-Ion / Li-Poly cells is below the 1C rate, with an absolute maximum current at the 2C rate. The recommended fast charge current should be obtained from battery manufacturer. For example, a 500 mAh battery pack with 0.7C preferred fast charge current has a charge current of 350 mA. Charging at this rate provides the shortest charge cycle times without degradation to the battery pack performance or life. Note: 6.1.1.2 Please consult with your battery supplier or refer to battery data sheet for preferred charge rate. Thermal Considerations The worst-case power dissipation in the battery charger occurs when the input voltage is at the maximum and the device has transitioned from the Preconditioning mode to the Constant-current mode. In this case, the power dissipation is: EQUATION 6-1: PowerDissipation = ( V DDMAX - V PTHMIN ) x I REGMAX Where: Power dissipation with a 9V, 10% input voltage source, 500 mA 10% and preconditioning threshold voltage at 6V is: EQUATION 6-2: PowerDissipation = ( 9.9 V - 6.0 V ) x 550mA = 2.15 W This power dissipation with the battery charger in the DFN-10 package will result approximately 92C above room temperature. 6.1.1.3 The MCP73213 is stable with or without a battery load. In order to maintain good AC stability in the Constantvoltage mode, a minimum capacitance of 1 F is recommended to bypass the VBAT pin to VSS. This capacitance provides compensation when there is no battery load. In addition, the battery and interconnections appear inductive at high frequencies. These elements are in the control feedback loop during Constant-voltage mode. Therefore, the bypass capacitance may be necessary to compensate for the inductive nature of the battery pack. A minimum of 16V rated 1 F, is recommended to apply for output capacitor and a minimum of 25V rated 1 F, is recommended to apply for input capacitor for typical applications. TABLE 6-1: = the maximum input voltage IREGMAX = the maximum fast charge current VPTHMIN = the minimum transition threshold voltage DS22190B-page 22 MLCC CAPACITOR EXAMPLE MLCC Capacitors Temperature Range X7R -55C to +125C 15% X5R -55C to +85C 15% Tolerance Virtually any good quality output filter capacitor can be used, independent of the capacitor's minimum Effective Series Resistance (ESR) value. The actual value of the capacitor (and its associated ESR) depends on the output load current. A 1 F ceramic, tantalum or aluminum electrolytic capacitor at the output is usually sufficient to ensure stability. 6.1.1.4 VDDMAX External Capacitors Reverse-Blocking Protection The MCP73213 provides protection from a faulted or shorted input. Without the protection, a faulted or shorted input would discharge the battery pack through the body diode of the internal pass transistor. (c) 2009 Microchip Technology Inc. MCP73213 6.2 PCB Layout Issues For optimum voltage regulation, place the battery pack as close as possible to the device's VBAT and VSS pins, recommended to minimize voltage drops along the high current-carrying PCB traces. If the PCB layout is used as a heatsink, adding many vias in the heatsink pad can help conduct more heat to the backplane of the PCB, thus reducing the maximum junction temperature. Figure 6-4 and Figure 6-5 depict a typical layout with PCB heatsinking. FIGURE 6-5: Typical Layout (Bottom). 102-00261 MCP73213EV FIGURE 6-3: Typical Layout (Top). FIGURE 6-4: Typical Layout (Top Metal). (c) 2009 Microchip Technology Inc. DS22190B-page 23 MCP73213 NOTES: DS22190B-page 24 (c) 2009 Microchip Technology Inc. MCP73213 7.0 PACKAGING INFORMATION 7.1 Package Marking Information Example: 10-Lead DFN (3x3) Standard * XXXX Part Number YYWW MCP73213-A6SI/MF MCP73213-B6SI/MF NNN Legend: XX...X Y YY WW NNN e3 * Note: Code Z3HI Y3HI Z3HI 0923 256 Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code Pb-free JEDEC designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. (c) 2009 Microchip Technology Inc. DS22190B-page 25 MCP73213 % !" #$ 2 % & %! % *" ) ' % * $% %"% %% 133)))& &3 * D e b N N L K E E2 EXPOSED PAD NOTE 1 2 1 2 1 NOTE 1 D2 BOTTOM VIEW TOP VIEW A A1 A3 NOTE 2 4% & 5&% 6!&( $ 55, , 6 6 67 8 % 7 9 % : %" $$ . 0 %% * ./0 + 7 5% ,# ""5% ,2 +/0 +. : 7 ;"% , ,# , .: . ( : . + 5 + . < = = "";"% 0 %%;"% 0 %%5% 0 %%% ,# "" +/0 % !"#$%! & '(!%&! %( %")% % % " *& & # "%( %" + * ) !%" & "% ,-. /01 / & %#%! ))% !%% ,21 $ & '! !)% !%% '$ $ &% ! DS22190B-page 26 ) 0>+/ (c) 2009 Microchip Technology Inc. MCP73213 % !" #$ 2 % & %! % *" ) ' % * $% %"% %% 133)))& &3 * (c) 2009 Microchip Technology Inc. DS22190B-page 27 MCP73213 NOTES: DS22190B-page 28 (c) 2009 Microchip Technology Inc. MCP73213 APPENDIX A: REVISION HISTORY Revision B (December 2009) The following is the list of modifications: 1. Updated the Battery Short Protection values in the DC Characteristics table. Revision A (July 2009) * Original Release of this Document. (c) 2009 Microchip Technology Inc. DS22190B-page 29 MCP73213 NOTES: DS22190B-page 30 (c) 2009 Microchip Technology Inc. MCP73213 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. X XX Device Temperature Range Package Device: MCP73213: MCP73213T: Temperature Range: I Package: MF Examples: a) b) Dual Cell Li-Ion/Li-Polymer Battery Device Dual Cell Li-Ion/Li-Polymer Battery Device, Tape and Reel = -40C to +85C (Industrial) c) d) MCP73213-A6SI/MF: Dual Cell Li-Ion/ Li-Polymer Battery Device MCP73213-B6SI/MF: Dual Cell Li-Ion/ Li-Polymer Battery Device MCP73213T-A6SI-MF: Tape and Reel, Dual Cell Li-Ion/ Li-Polymer Battery Device MCP73213T-B6SI/MF: Tape and Reel, Dual Cell Li-Ion/ Li-Polymer Battery Device = Plastic Dual Flat No Lead, 3x3 mm Body (DFN), 10-Lead (c) 2009 Microchip Technology Inc. DS22190B-page 31 MCP73213 NOTES: DS22190B-page 32 (c) 2009 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, rfPIC and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Octopus, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, PIC32 logo, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2009, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. (c) 2009 Microchip Technology Inc. DS22190B-page 33 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://support.microchip.com Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4080 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Kokomo Kokomo, IN Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8528-2100 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 03/26/09 DS22190B-page 34 (c) 2009 Microchip Technology Inc.