Specification of Automotive MLCC Samsung P/N : Supplier : Samsung electro-mechanics Product : Multi-layer Ceramic Capacitor CL31B104KBP5PNE CAP, 100, 50V, 10%, X7R, 1206 Description : AEC-Q 200 Specified A. Samsung Part Number Series Size Dielectric Capacitance Capacitance tolerance Rated Voltage Thickness CL 31 B 104 K B P 5 P N E Samsung Multi-layer Ceramic Capacitor 1206 (inch code) L: 3.2 0.15 X7R 100 10 % 50 V 1.15 0.15 mm mm W: Inner electrode Termination Plating Product Grade code Packaging 1.6 0.15 mm Ni , Open mode Cu , Ag-epoxy Sn 100% (Pb Free) Automotive Standard Embossed Type, 7" reel B. Reliablility Test and Judgement condition Performance Test condition High Temperature Appearance : No abnormal exterior appearance Unpowered, 1000hrs@T=150 Exposure Capacitance Change : Within 10% Measurement at 242hrs after test conclusion Tan : 0.03 max IR : More than 10,000 or 500x Whichever is Smaller Temperature Cycling Appearance : No abnormal exterior appearance 1000Cycles Capacitance Change : Within 10% Measurement at 242hrs after test conclusion Tan : 0.03 max 1 cycle condition : IR : More than 10,000 or 500x Whichever is Smaller Destructive Physical No Defects or abnormalities -55+0/-3(153min) -> Room Temp(1min.) -> 125+3/-0(153min) -> Room Temp(1min.) Per EIA 469 Analysis Moisture Resistance Appearance : No abnormal exterior appearance 10Cycles, t=24hrs/cycle Capacitance Change : Within 12.5% Heat (25~65) and humidity (80~98%), Unpowered Tan : 0.03 max measurement at 242hrs after test conclusion IR : More than 10,000 or 500x Whichever is Smaller Humidity Bias Appearance : No abnormal exterior appearance 1000hrs 85/85%RH, Rated Voltate and 1.3~1.5V, Capacitance Change : Within 12.5% Add 100kohm resistor Tan : 0.035 max Measurement at 242hrs after test conclusion IR : More than 500 or 25x The charge/discharge current is less than 50mA. Whichever is Smaller High Temperature Appearance : No abnormal exterior appearance 1000hrs @ TA=125, 200% Rated Voltage, Operating Life Capacitance Change : Within 12.5% Measurement at 242hrs after test conclusion Tan : 0.035 max The charge/discharge current is less than 50mA. IR : More than 1000 or 50x Whichever is Smaller Performance External Visual No abnormal exterior appearance Physical Dimensions Within the specified dimensions Mechanical Shock Microscope (10) Using The calipers Appearance : No abnormal exterior appearance Three shocks in each direction should be applied along Capacitance Change : Within 10% Tan , IR : initial spec. Vibration Test condition 3 mutually perpendicular axes of the test specimen (18 shocks) Peakvalue Duration Wave Velocity 1,500G 0.5ms Half sine 4.7m/sec. Appearance : No abnormal exterior appearance 5g's for 20min., 12cycles each of 3 orientations, Capacitance Change : Within 10% Tan , IR : initial spec. Use 8"x5" PCB 0.031" Thick 7 secure points on one long side and 2 secure points at corners of opposite sides. Parts mounted within 2" from any secure point. Test from 10~2000. Resistance to Appearance : No abnormal exterior appearance Solder pot : 2605, 101sec. Solder Heat Capacitance Change : Within 10% Tan , IR : initial spec. Thermal Shock Appearance : No abnormal exterior appearance -55/+125. Capacitance Change : Within 10% Note: Number of cycles required-300, Tan , IR : initial spec. Maximum transfer time-20 sec, Dwell time-15min. Air-Air Appearance : No abnormal exterior appearance AEC-Q200-002 ESD Capacitance Change : Within 10% Tan , IR : initial spec. Solderability 95% of the terminations is to be soldered a) Preheat at 155 for 4 hours, Immerse in solder for 5s at 2455 evenly and continuously b) Steam aging for 8 hours, Immerse in solder for 5s at 2455 c) Steam aging for 8 hours, Immerse in solder for 120s at 2605 solder : a solution ethanol and rosin Electrical Capacitance : Within specified tolerance The Capacitance /D.F. should be measured at 25, Characterization Tan (DF) : 0.025 max. 110%, 1.00.2Vrms IR(25) : More than 10,000 or 500x I.R. should be measured with a DC voltage not exceeding IR(125) : More than1,000 or 10x Rated Voltage @25, @125 for 60~120 sec. Whichever is Smaller Dielectric Strength Board Flex Dielectric Strength : 250% of the rated voltage for 1~5 seconds Appearance : No abnormal exterior appearance Bending to the limit (2) for 5 seconds Capacitance Change : Within 10% Terminal Appearance : No abnormal exterior appearance 18N, for 601 sec. Strength(SMD) Capacitance Change : Within 10% Beam Load Destruction value should not be exceed Beam speed Chip Length 3.2 2.50.25/sec a) Chip Thickness < 1.25 : 15N Temperature b) Chip Thickness 1.25 : 54.5N X7R Characterisitcs (From -55 to 125, Capacitance change shoud be within 15%) C. Recommended Soldering method : Reflow ( Reflow Peak Temperature : 260+0/-5, 10sec. Max ) Meet IPC/JEDEC J-STD-020 D Standard * For the more detail Specification, Please refer to the Samsung MLCC catalogue.