TYPE 3613C SERIES
Product – Specification
1st April 2003
ISSUE 5
Telephone Tyco Passive Product Support Team ++ 44 (0) 1793 572484
Website – www.resistors.tycoelectronics.com Email – passivesales@tycoelectronics.com
Page 1 of 4
Moulded Chip Inductor 18:12
TYPE 3613C SERIES
Specially developed for automatic mounting
applications, this exciting range of chip
inductors are ferrite based and sealed in a
thermoset plastic body. They employ solder
coated copper terminations with barrier layer.
Customers can therefore expect consistent
quality, performance and reliability. Its smooth
top surface makes it particularly well suited to
pick and place equipments.
Truly the last word in 1812 chip inductors.
KEY FEATURES
• High Reliability
• Two Versatile Types
• Small Versatile Size - 3.2 x 4.5 mm
• Temperature Range -25°C to +100°C
• Supplied in Standard Carrier Tape
• Suitable for Dip and Wave Solder
• Insulation 1000M R min
• Available from Stock
STOCKISTS:
This product is available from Farnell.
TYPE 3613C SERIES
Product – Specification
1st April 2003
ISSUE 5
Telephone Tyco Passive Product Support Team ++ 44 (0) 1793 572484
Website – www.resistors.tycoelectronics.com Email – passivesales@tycoelectronics.com
Page 2 of 4
3613C Style Operating Characteristics
5% Tolerance available on selected value ranges. Please enquire.
TYPE 3613C SERIES
Product – Specification
1st April 2003
ISSUE 5
Telephone Tyco Passive Product Support Team ++ 44 (0) 1793 572484
Website – www.resistors.tycoelectronics.com Email – passivesales@tycoelectronics.com
Page 3 of 4
DIMENSIONS
PACKAGING (REEL) PACKAGING (TAPE)
ENVIRONMENTAL
TEST NOTES
Insulation: 1000 M ohms The measuring method for the test data given overpage are as follows:
Temperature Range: -25°C to +85°C
∆L/L within ± 10%
Inductance: Direct reading from Q-meter (equivalent to YHP 4342A, jig used)
Q: Direct reading from Q-meter (equivalent to YHP 4342A, jig used)
Humidity Load life: ∆L/L within ± 5% Self resonant frequency: Grid Dipo Meter (equivalent to Measurement M159)
DC resistance: Wheatstone bridge (equivalent to YEW 2755)
Vibration (see test method): Unless otherwise specified, the temperature is 20°C ± 5°C and the humidity is 65% ± 20%
HOW TO ORDER
TYPE 3613C SERIES
Product – Specification
1st April 2003
ISSUE 5
Telephone Tyco Passive Product Support Team ++ 44 (0) 1793 572484
Website – www.resistors.tycoelectronics.com Email – passivesales@tycoelectronics.com
Page 4 of 4
TEST METHODS
ITEM STANDARD TEST METHOD
DC SUPERPOSITION
CHARACTERISTICS
∆L/L Within -10%
When the allowable current was applied, the inductance was
measured with a YHP 4262A and compared with the initial
value.
TEMPERATURE
RISE
Within 20°C
When the allowable current was applied, the amount of
temperature rise was measured by the change in resistance.
TEMPERATURE
RISE
∆L/L Within ± 5%
Measurements were taken in a temperature range of -25°C to
85°C and the value at +20°C was used as the standard value.
OVERCURRENT
TEST
No smoke and no fire
Twice the allowable current was applied for a period of five
minutes.
SOLDERING HEAT
RESISTANCE TEST
No pronounced abnormality
in appearance
Immersion twice for a period of 5 ± 0.5 seconds in H63A
solder at a temperature 260°C ± 5°C
SOLDERABILITY Not less than 90% bonding to
electrode surfaces
Immersion for a period of 2 ± 0.5 seconds in H63A solder at a
temperature of 230 ± 5°C. Flux used was a rosin-core solution
containing approximately 25% methanol.
INSULATION
RESISTANCE
Not less than 1000 M
0.3mm diameter copper wires were wound around the coils
three times and measurements were taken after 250VDC was
applied between the wire and the terminals for a period of 1
minute.
TENSILE
STRENGTH TEST
No separation from substrate
After the inductors were soldered to substrates, a force of
1.0kg was applied in both the x and y directions for a period
of 5 seconds.
STRESS TEST No breakage After the inductors were mounted on substrates, 1-mins. 10-
55-10 cycle per seconds sweeps 1.5mm stroke vibrations were
applied for 2 hrs. each in the X, Y and Z directions
DROP TEST
No pronounced abnormality in appearance
The inductors were dropped 10 times from a height of 1.0
metre onto a concrete floor.
VIBRATION TEST ∆L/L Within ± 10%
Q Not less than 30
After the inductors were mounted on substrates, 1-mins. 10-
55-10 cycle per seconds sweeps 1.5mm stroke vibrations were
applied for 2 hours each in the X, Y and Z directions
HUMIDITY RESISTANCE
LOAD TEST
∆L/L Within ± 10%
Q Not less than 30 Measurements were taken after the allowable current was
applied while the inductors were stored at 60°C ± 2°C in 90 to
95% RH for a period of 500 hours.
LOW TEMPERATURE
RESISTANCE TEST
∆L/L Within ± 10%
Q Not less than 30 Measurements were taken after the inductors were stored at -
40°C ± 2°C for period 1000 hours
TEMPERATURE
CYCLE TEST
∆L/L Within ± 10%
Q Not less than 30 Measurements were taken after the inductors were stored for
30 minutes, during which they were subjected to 20
temperature cycles of between -25°C and +85°C.
HIGH TEMPERATURE
RESISTANCE
LOAD TEST
∆L/L Within ± 10%
Q Not less than 30 Measurements were taken after the allowable was applied
while the inductors were stored at 85°C for a period of 1000
hours.
This publication is issued to provide outline information only and (unless specifically agreed to the contrary by the Company in writing) is not to form part of any order or be
regarded as a representation relating to the products or service concerned. We reserve the right to alter without notice the specification, design, price or conditions of
supply of any product or service. Whilst Tyco Electronics Components products are of the very highest quality and reliability, all electronic components can occasionally
be subject to failure. Where failure of a Tyco Electronics Components product could result in life threatening consequences, then the circuit and application must
be discussed with the Company. Such areas might include ECG, respiratory and other medical and nuclear applications and any non fail-safe applications circuit.
