DETAIL SPECIFICATION SHEET
CONNECTORS, ELECTRICAL, (CIRCULAR, ENVIRONME NT RESISTING),
RECEPTACLE, (FLANGE MOUNT, THREADED COUPLING, CRIMP PIN CONTACT),
(SERIES III, CLASSES A, G, K, M, N, R, S, T, W AND Z)
This specification is approved for use by all Departments
and Agencies of the Department of Defense.
The requirements for acquiring the product described herein
shall consist of this specification sheet and MIL-DTL-83723.
FIGURE 1. Classes A, G, K, M, R, T, W and Z.
AMSC N/A FSC 5935
INCH-POUND
MIL-DTL-83723/83E
1 October 2009
SUPERSEDING
MIL-C-83723/83D
30 June 1992
MIL-DTL-83723/83E
2
FIGURE 1. Classes A, G, K, M, R, T, W and Z - Continued.
MIL-DTL-83723/83E
3
Inches
mm
Inches
mm
Inches
mm
Inches
mm
Inches
mm
.005
0.08
.069
1.75
.130
3.30
.418
10.62
.685
17.40
.008
0.20
.071
1.80
.138
3.51
.424
10.77
.696
17.68
.010
0.25
.076
1.93
.144
3.66
.433
11.00
.700
17.78
.015
0.38
.078
1.98
.160
4.06
.480
12.19
.705
17.19
.018
0.46
.084
2.13
.195
4.95
.490
12.45
.708
17.98
.020
0.51
.089
2.26
.198
4.27
.515
13.08
.719
18.26
.022
0.56
.092
2.34
.204
5.18
.518
13.16
.728
18.49
.025
0.64
.093
2.36
.281
7.14
.530
13.46
.754
19.15
.032
0.81
.097
2.46
.290
7.37
.535
13.59
.769
19.53
.035
0.89
.098
2.49
.329
8.36
.558
14.17
.772
19.61
.042
1.07
.100
2.54
.340
8.64
.562
14.27
.774
19.66
.046
1.17
.101
2.57
.351
8.92
.580
14.70
.061
1.55
.106
2.69
.388
9.86
.594
15.09
.063
1.60
.112
2.84
.394
10.01
.627
15.93
.065
1.65
.125
3.18
.413
10.49
.636
16.15
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for information only.
3. Unless otherwise specified, tolerances are ± .005 (0.13 mm) for three place decimals and
± .01 (0.25 mm) for two place decimals and ±1° for all angles.
4. Coupling indicator line shall be color coded red.
5. Rear accessory interchangeability dimensions shall be in accordance with MIL-DTL-83723.
6. Shell size 8 will not mate with MIL-DTL-26500 connectors.
7. Phantomed configuration optional.
8. See table I for contact cavities requiring this dimension.
9. The centerline of indicated projection must be located on vertical centerline ± 2°.
FIGURE 1. Classes A, G, K, M, R, T, W and Z - Continued.
MIL-DTL-83723/83E
4
FIGURE 2. Classes N and S.
MIL-DTL-83723/83E
5
Inches mm Inches mm Inches mm Inches mm Inches mm
.005
0.08
.069
1.75
.130
3.30
.418
10.62
.685
17.40
.008
0.20
.071
1.80
.138
3.51
.424
10.77
.696
17.68
.010
0.25
.076
1.93
.144
3.66
.433
11.00
.700
17.78
.015
0.38
.078
1.98
.160
4.06
.480
12.19
.705
17.19
.018
0.46
.084
2.13
.195
4.95
.490
12.45
.708
17.98
.020
0.51
.089
2.26
.198
4.27
.515
13.08
.719
18.26
.022
0.56
.092
2.34
.204
5.18
.518
13.16
.728
18.49
.025
0.64
.093
2.36
.281
7.14
.530
13.46
.754
19.15
.032
0.81
.097
2.46
.290
7.37
.535
13.59
.769
19.53
.035
0.89
.098
2.49
.329
8.36
.558
14.17
.772
19.61
.042
1.07
.100
2.54
.340
8.64
.562
14.27
.774
19.66
.046
1.17
.101
2.57
.351
8.92
.580
14.70
.061
1.55
.106
2.69
.388
9.86
.594
15.09
.063
1.60
.112
2.84
.394
10.01
.627
15.93
.065
1.65
.125
3.18
.413
10.49
.636
16.15
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for information only.
3. Unless otherwise specified, tolerances are ± .005 (0.13 mm) for three place decimals and
± .01 (0.25 mm) for two place decimals and ±1° for all angles.
4. Coupling indicator line shall be color coded red.
5. Rear accessory interchangeability dimensions shall be in accordance with MIL-DTL-83723.
6. Shell size 8 will not mate with MIL-DTL-26500 connectors.
7. Phantomed configuration optional.
8. See table I for contact cavities requiring this dimension.
9. The centerline of indicated projection must be located on vertical centerline ± 2°.
FIGURE 2. Classes N and S – Continued.
MIL-DTL-83723/83E
6
Inches
mm
.116
2.95
.125
3.18
Shell size A thread
coupling thread B max C D max F max
8 .562-24 UNEF-2A .394 .418
.413
.290 .562
10 .688-24 UNEF-2A .515 .535
.530
.388 .696
12 .875-20 UNEF-2A .685 .705
.700
.558 .875
14 .938-20 UNEF-2A .754 .774
.769
.627 .936
16 1.062-18 UNEF-2A .881 .901
.896
.772 1.062
18 1.188-18 UNEF-2A .987 1.007
1.002
.860 1.187
20 1.312-18 UNEF-2A 1.112 1.132
1.127
.985 1.312
22 1.438-18 UNEF-2A 1.237 1.257
1.252
1.110 1.437
24 1.562-18 UNEF-2A 1.362 1.382
1.377
1.235 1.562
FIGURE 3. Dimensions and configurations.
MIL-DTL-83723/83E
7
Shell size G H
R
number of
teeth
S
+.005 / -.000
T
8 .594 .812 12 .490 .076
10
.719
.937
15
.636
.089
.084
12
.812
1.031
21
.806
14
.906
1.125
24
.875
16
.969
1.250
30
1.002
18
1.062
1.343
33
1.108
20
1.156
1.437
36
1.233
22
1.250
1.562
39
1.358
24
1.375
1.703
42
1.483
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for information only.
3. Unless otherwise specified, tolerances are ± .005 (0.13 mm) for three place decimals and
± .01 (0.25 mm) for two place decimals and ± 1° for all angles.
4. Coupling indicator line shall be color coded red.
5. Rear accessory interchangeability dimensions shall be in accordance with MIL-DTL-83723.
6. Shell size 8 will not mate with MIL-DTL-26500 connectors.
7. Phantomed configuration optional.
8. See table I for contact cavities requiring this dimension.
9. The centerline of indicated projection must be located on vertical centerline ± 2°.
FIGURE 3. Dimensions and configurations - Continued.
REQUIREMENTS:
Dimensions and configurations: See figures 1 and 3 for classes A, G, K, M, R, T, W and Z.
See figures 2 and 3 for classes N and S.
This connector mates with MIL-DTL-83723/86, MIL-DTL-83723/91 and MIL-DTL-83723/95 and
MIL-C-83723/97.
Insert arrangements and polarizing positions: See MIL-STD-1554 and table I.
TABLE I. Insert arrangements requiring reduced diameter for raised
seal barriers on outer row of contact cavities as indicated.
Shell size Insert arrangements Contact cavities
8
10 03, 98
06 1, 2, 3
1, 2, 3, 4, 5, 6
MIL-DTL-83723/83E
8
O-ring: See MIL-DTL-83723.
Part or Identifying Number (PIN) example:
M83723/ 83 W 22 55 N
Military designation
Specification sheet number
Class
Shell size
Insert arrangement
Polarizing position
Changes from previous issue. Marginal notations are not used in this revision to identify changes with
respect to the previous issue, due to the extent of the changes.
Referenced documents. In addition to MIL-DTL-83723, this document references the following:
MIL-STD-1554
MIL-DTL-26500
MIL-C-83723/97
MIL-DTL-83723/86
MIL-DTL-83723/91
MIL-DTL-83723/95
CONCLUDING MATERIAL
Custodians: Preparing activity:
Army - CR DLA - CC
Navy - AS
Air Force - 85 (Project 5935-2008-162)
DLA - CC
Review activities:
Army - AR, MI
Navy - EC
Air Force - 19, 99
NOTE: The activities listed above were interested in this document as of the date of this document.
Since organizations and responsibilities can change, y ou should verify the currency of the information
above using the ASSIST Online database at http://assist.daps.dla.mil.