Product Folder Sample & Buy Support & Community Tools & Software Technical Documents LM1881 SNLS384G - FEBRUARY 1995 - REVISED JUNE 2015 LM1881 Video Sync Separator 1 Features 3 Description * * * * * * * * * The LM1881 Video sync separator extracts timing information including composite and vertical sync, burst or back porch timing, and odd and even field information from standard negative going sync NTSC, PAL (1) and SECAM video signals with amplitude from 0.5-V to 2-V p-p. The integrated circuit is also capable of providing sync separation for nonstandard, faster horizontal rate video signals. The vertical output is produced on the rising edge of the first serration in the vertical sync period. A default vertical output is produced after a time delay if the rising edge mentioned above does not occur within the externally set delay period, such as might be the case for a non-standard video signal. 1 AC Coupled Composite Input Signal >10-k Input Resistance <10-mA Power Supply Drain Current Composite Sync and Vertical Outputs Odd and Even Field Output Burst Gate or Back Porch Output Horizontal Scan Rates to 150 kHz Edge Triggered Vertical Output Default Triggered Vertical Output for NonStandard Video Signal (Video Games-Home Computers) Device Information(1) 2 Applications * * * * * Video Cameras and Recorders Broadcasting Systems Set-Top Boxes Home Entertainment Computing and Gaming Applications PART NUMBER LM1881 PACKAGE BODY SIZE (NOM) SOIC (8) 4.90 mm x 3.91 mm PDIP (8) 9.81 mm x 6.35 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. (1) PAL in this datasheet refers to European broadcast TV standard "Phase Alternating Line", and not to Programmable Array Logic. Typical Connection Diagram 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LM1881 SNLS384G - FEBRUARY 1995 - REVISED JUNE 2015 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 3 6.1 6.2 6.3 6.4 6.5 6.6 3 4 4 4 4 5 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Electrical Characteristics LM1881............................. Dissipation Ratings ................................................... Typical Characteristics .............................................. Detailed Description .............................................. 6 7.1 Overview ................................................................... 6 7.2 Functional Block Diagram ......................................... 6 7.3 Feature Description................................................... 7 7.4 Device Functional Modes........................................ 10 8 Application and Implementation ........................ 11 8.1 Application Information............................................ 11 8.2 Typical Applications ................................................ 11 9 Power Supply Recommendations...................... 13 10 Device and Documentation Support ................. 14 10.1 10.2 10.3 10.4 Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 14 14 14 14 11 Mechanical, Packaging, and Orderable Information ........................................................... 14 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision F (March 2013) to Revision G * Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1 Changes from Revision E (March 2013) to Revision F * 2 Page Page Changed layout of National Data Sheet to TI format ........................................................................................................... 13 Submit Documentation Feedback Copyright (c) 1995-2015, Texas Instruments Incorporated Product Folder Links: LM1881 LM1881 www.ti.com SNLS384G - FEBRUARY 1995 - REVISED JUNE 2015 5 Pin Configuration and Functions D and P Packages 8-Pin SOIC and PDIP Top View Pin Functions PIN NO. NAME 1 CSOUT 2 CVIN 3 VSOUT 4 GND 5 BPOUT 6 RSET 7 OEOUT 8 VCC TYPE DESCRIPTION Output Composite Sync Output Input Composite Video Input Output -- Output Input Output Input Vertical Sync Output Ground Burst or Back Porch Timing Output Charge Current External Resistor Odd and Even Field Output Supply Voltage 6 Specifications 6.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) (2) MIN Supply Voltage Input Voltage MAX UNIT 13.2 V 3 VP-P 6 VP-P (VCC = 5) (VCC 8) V Output Sink Currents; Pins, 1, 3, 5 5 mA Output Sink Current; Pin 7 2 mA PDIP Package (10 sec.) Soldering Information SOIC Package 260 Vapor Phase (60 sec.) 215 Infrared (15 sec.) 220 -65 Storage temperature, Tstg (1) (2) 150 C C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications. Submit Documentation Feedback Copyright (c) 1995-2015, Texas Instruments Incorporated Product Folder Links: LM1881 3 LM1881 SNLS384G - FEBRUARY 1995 - REVISED JUNE 2015 www.ti.com 6.2 ESD Ratings VALUE V(ESD) (1) Electrostatic discharge Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) 2000 Machine Model 200 UNIT V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) TA Operating free-air temperature MIN MAX 0 70 UNIT C 6.4 Electrical Characteristics LM1881 VCC = 5 V; RSET = 680 k; TA = 0C to +70C by correlation with 100% electrical testing at TA=25C PARAMETER Supply Current TYP (1) MAX VCC = 5 V 5.2 10 VCC = 12 V 5.5 12 1.3 1.5 1.8 V 55 70 85 mV 11 16 A TEST CONDITIONS Outputs at Logic 1 MIN UNIT mA DC Input Voltage Pin 2 Input Threshold Voltage See Input Discharge Current Pin 2; VIN = 2 V 6 Input Clamp Charge Current Pin 2; VIN = 1 V 0.2 0.8 RSET Pin Reference Voltage Pin 6; (3) 1.1 1.22 Composite Sync. & Vertical Outputs IOUT = 40 A; Logic 1 VCC = 5 V 4.0 4.5 VCC = 12 V 11 IOUT = 1.6 mA Logic 1 VCC = 5 V 2.4 VCC = 12 V 10 Burst Gate and Odd and Even Outputs IOUT = 40 A; Logic 1 VCC = 5 V 4 VCC = 12 V 11 Composite Sync. Output IOUT = -1.6 mA; Logic 0; Pin 1 0.2 0.8 V Vertical Sync. Output IOUT = -1.6 mA; Logic 0; Pin 3 0.2 0.8 V Burst Gate Output IOUT = -1.6 mA; Logic 0; Pin 5 0.2 0.8 V Odd and Even Output IOUT = -1.6 mA; Logic 0; Pin 7 0.2 0.8 V 230 300 s 2.5 4 4.7 s 32 65 90 s (2) Vertical Sync Width 190 Burst Gate Width 2.7 k from Pin 5 to VCC Vertical Default Time See (1) (2) (3) (4) (4) mA 1.35 V V 3.6 V 4.5 V Typicals are at TJ = 25C and represent the most likely parametric norm. Relative difference between the input clamp voltage and the minimum input voltage which produces a horizontal output pulse. Careful attention should be made to prevent parasitic capacitance coupling from any output pin (Pins 1, 3, 5 and 7) to the RSET pin (Pin 6). Delay time between the start of vertical sync (at input) and the vertical output pulse. 6.5 Dissipation Ratings MIN Package Dissipation (1) (1) 4 MAX UNIT 1100 mW For operation in ambient temperatures above 25C, the device must be derated based on a 150C maximum junction temperature and a package thermal resistance of 110C/W, junction to ambient. Submit Documentation Feedback Copyright (c) 1995-2015, Texas Instruments Incorporated Product Folder Links: LM1881 LM1881 www.ti.com SNLS384G - FEBRUARY 1995 - REVISED JUNE 2015 6.6 Typical Characteristics Figure 1. RSET Value Selection vs Vertical Serration Pulse Separation Figure 2. Vertical Default Sync Delay Time vs RSET Figure 3. Burst or Black Level Gate Time vs RSET Figure 4. Vertical Pulse Width vs RSET VERTICAL PULSE WIDTH (Ps) 500 400 300 200 100 -40 -20 0 20 40 60 80 100 TEMPERATURE (C) Figure 5. Vertical Pulse Width vs Temperature Figure 6. Supply Current vs Supply Voltage Submit Documentation Feedback Copyright (c) 1995-2015, Texas Instruments Incorporated Product Folder Links: LM1881 5 LM1881 SNLS384G - FEBRUARY 1995 - REVISED JUNE 2015 www.ti.com 7 Detailed Description 7.1 Overview The LM1881 is designed to strip the synchronization signals from composite video sources that are in, or similar to, the N.T.S.C. format. Input signals with positive polarity video (increasing signal voltage signifies increasing scene brightness) from 0.5 V (p-p) to 2 V (p-p) can be accommodated. The LM1881 operates from a single supply voltage between 5-V DC and 12-V DC. The only required external components besides a power supply decoupling capacitor at pin 8 and a set current decoupling capacitor at pin 6, are the composite input coupling capacitor at pin 2 and one resistor at pin 6 that sets internal current levels. The resistor on pin 6 (that is, Rset) allows the LM1881 to be adjusted for source signals with line scan frequencies differing from 15.734 kHz. Four major sync signals are available from the I/C; composite sync including both horizontal and vertical scan timing information; a vertical sync pulse; a burst gate or back porch clamp pulse; and an odd and even output. The odd and even output level identifies which video field of an interlaced video source is present at the input. The outputs from the LM1881 can be used to gen-lock video camera/VTR signals with graphics sources, provide identification of video fields for memory storage, recover suppressed or contaminated sync signals, and provide timing references for the extraction of coded or uncoded data on specific video scan lines. To better understand the LM1881 timing information and the type of signals that are used, refer to Figure 7(a-e) which shows a portion of the composite video signal from the end of one field through the beginning of the next field. 7.2 Functional Block Diagram *Components Optional, See Text 6 Submit Documentation Feedback Copyright (c) 1995-2015, Texas Instruments Incorporated Product Folder Links: LM1881 LM1881 www.ti.com SNLS384G - FEBRUARY 1995 - REVISED JUNE 2015 7.3 Feature Description 7.3.1 Composite Sync Output The composite sync output, Figure 7(b), is simply a reproduction of the signal waveform below the composite video black level, with the video completely removed. This is obtained by clamping the video signal sync tips to 1.5-V DC at Pin 2 and using a comparator threshold set just above this voltage to strip the sync signal, which is then buffered out to Pin 1. The threshold separation from the clamped sync tip is nominally 70 mV which means that for the minimum input level of 0.5 V (p-p), the clipping level is close to the halfway point on the sync pulse amplitude (shown by the dashed line on Figure 7(a). This threshold separation is independent of the signal amplitude, therefore, for a 2-V (p-p) input the clipping level occurs at 11% of the sync pulse amplitude. The charging current for the input coupling capacitor is 0.8 mA, Normally the signal source for the LM1881 is assumed to be clean and relatively noise-free, but some sources may have excessive video peaking, causing high-frequency video and chroma components to extend below the black level reference. Some video discs keep the chroma burst pulse present throughout the vertical blanking period so that the burst actually appears on the sync tips for three line periods instead of at black level. A clean composite sync signal can be generated from these sources by filtering the input signal. When the source impedance is low, typically 75 , a 620- resistor in series with the source and a 510-pF capacitor to ground will form a lowpass filter with a corner frequency of 500 kHz. This bandwidth is more than sufficient to pass the sync pulse portion of the waveform; however, any subcarrier content in the signal will be attenuated by almost 18 dB, effectively taking it below the comparator threshold. Filtering will also help if the source is contaminated with thermal noise. The output waveforms will become delayed from between 40 ns to as much as 200 ns due to this filter. This much delay will not usually be significant but it does contribute to the sync delay produced by any additional signal processing. Because the original video may also undergo processing, the need for time delay correction will depend on the total system, not just the sync stripper. 7.3.2 Vertical Sync Output A vertical sync output is derived by internally integrating the composite sync waveform (Functional Block Diagram). To understand the generation of the vertical sync pulse, refer to the lower left hand section Functional Block Diagram. Note there are two comparators in the section. One comparator has an internally generated voltage reference called V1 going to one of its inputs. The other comparator has an internally generated voltage reference called V2 going to one of its inputs. Both comparators have a common input at their noninverting input coming from the internal integrator. The internal integrator is used for integrating the composite sync signal. This signal comes from the input side of the composite sync buffer and are positive going sync pulses. The capacitor to the integrator is internal to the LM1881. The capacitor charge current is set by the value of the external resistor RSET. The output of the integrator is going to be at a low voltage during the normal horizontal lines because the integrator has a very short time to charge the capacitor, which is during the horizontal sync period. The equalization pulses will keep the output voltage of the integrator at about the same level, below the V1. During the vertical sync period the narrow going positive pulses shown in Figure 7 is called the serration pulse. The wide negative portion of the vertical sync period is called the vertical sync pulse. At the start of the vertical sync period, before the first Serration pulse occurs, the integrator now charges the capacitor to a much higher voltage. At the first serration pulse the integrator output should be between V1 and V2. This would give a high level at the output of the comparator with V1 as one of its inputs. This high is clocked into the "D" flip-flop by the falling edge of the serration pulse (remember the sync signal is inverted in this section of the LM1881). The "Q" output of the "D" flip-flop goes through the OR gate, and sets the R/S flip-flop. The output of the R/S flip-flop enables the internal oscillator and also clocks the ODD/EVEN "D" flip-flop. The ODD/EVEN field pulse operation is covered in Odd and Even Field Pulse. The output of the oscillator goes to a divide by 8 circuit, thus resetting the R/S flip-flop after 8 cycles of the oscillator. The frequency of the oscillator is established by the internal capacitor going to the oscillator and the external RSET. The "Q" output of the R/S flip-flop goes to pin 3 and is the actual vertical sync output of the LM1881. By clocking the "D" flip-flop at the start of the first serration pulse means that the vertical sync output pulse starts at this point in time and lasts for eight cycles of the internal oscillator as shown in Figure 7. Submit Documentation Feedback Copyright (c) 1995-2015, Texas Instruments Incorporated Product Folder Links: LM1881 7 LM1881 SNLS384G - FEBRUARY 1995 - REVISED JUNE 2015 www.ti.com Feature Description (continued) How RSET affects the integrator and the internal oscillator is shown under the Typical Performance Characteristics. The first graph is "RSET Value Selection vs Vertical Serration Pulse Separation". For this graph to be valid, the vertical sync pulse should last for at least 85% of the horizontal half line (47% of a full horizontal line). A vertical sync pulse from any standard should meet this requirement; both NTSC and PAL do meet this requirement (the serration pulse is the remainder of the period, 10% to 15% of the horizontal half line). Remember this pulse is a positive pulse at the integrator but negative in Figure 7. This graph shows how long it takes the integrator to charge its internal capacitor above V1. With RSET too large the charging current of the integrator will be too small to charge the capacitor above V1, thus there will be no vertical synch output pulse. As mentioned above, RSET also sets the frequency of the internal oscillator. If the oscillator runs too fast its eight cycles will be shorter than the vertical sync portion of the composite sync. Under this condition another vertical sync pulse can be generated on one of the later serration pulse after the divide by 8 circuit resets the R/S flip-flop. The first graph also shows the minimum RSET necessary to prevent a double vertical pulse, assuming that the serration pulses last for only three full horizontal line periods (six serration pulses for NTSC). The actual pulse width of the vertical sync pulse is shown in the "Vertical Pulse Width vs RSET" graph. Using NTSC as an example, lets see how these two graphs relate to each other. The Horizontal line is 64 s long, or 32 s for a horizontal half line. Now round this off to 30 s. In the "RSET Value Selection vs Vertical Serration Pulse Separation" graph the minimum resistor value for 30 s serration pulse separation is about 550 k. Going to the "Vertical Pulse Width vs RSET" graph one can see that 550 k gives a vertical pulse width of about 180 s, the total time for the vertical sync period of NTSC (3 horizontal lines). A 550 k will set the internal oscillator to a frequency such that eight cycles gives a time of 180 s, just long enough to prevent a double vertical sync pulse at the vertical sync output of the LM1881. The LM1881 also generates a default vertical sync pulse when the vertical sync period is unusually long and has no serration pulses. With a very long vertical sync time the integrator has time to charge its internal capacitor above the voltage level V2. Since there is no falling edge at the end of a serration pulse to clock the "D" flip-flop, the only high signal going to the OR gate is from the default comparator when output of the integrator reaches V2. At this time the R/S flip-flop is toggled by the default comparator, starting the vertical sync pulse at pin 3 of the LM1881. If the default vertical sync period ends before the end of the input vertical sync period, then the falling edge of the vertical sync (positive pulse at the "D" flip-flop) will clock the high output from the comparator with V1 as a reference input. This will retrigger the oscillator, generating a second vertical sync output pulse. The "Vertical Default Sync Delay Time vs RSET" graph shows the relationship between the RSET value and the delay time from the start of the vertical sync period before the default vertical sync pulse is generated. Using the NTSC example again the smallest resistor for RSET is 500 k. The vertical default time delay is about 50 s, much longer than the 30 s serration pulse spacing. A common question is how can one calculate the required RSET with a video timing standard that has no serration pulses during the vertical blanking. If the default vertical sync is to be used this is a very easy task. Use the "Vertical Default Sync Delay Time vs RSET" graph to select the necessary RSET to give the desired delay time for the vertical sync output signal. If a second pulse is undesirable, then check the "Vertical Pulse Width vs RSET" graph to make sure the vertical output pulse will extend beyond the end of the input vertical sync period. In most systems the end of the vertical sync period may be very accurate. In this case the preferred design may be to start the vertical sync pulse at the end of the vertical sync period, similar to starting the vertical sync pulse after the first serration pulse. A VGA standard is to be used as an example to show how this is done. In this standard a horizontal line is 32 s long. The vertical sync period is two horizontal lines long, or 64 s. The vertical default sync delay time must be longer than the vertical sync period of 64 s. In this case RSET must be larger than 680 k. RSET must still be small enough for the output of the integrator to reach V1 before the end of the vertical period of the input pulse. The first graph can be used to confirm that RSET is small enough for the integrator. Instead of using the vertical serration pulse separation, use the actual pulse width of the vertical sync period, or 64 s in this example. This graph is linear, meaning that a value as large as 2.7 M can be used for RSET (twice the value as the maximum at 30 s). Due to leakage currents it is advisable to keep the value of RSET under 2.0 M. In this example a value of 1.0 M is selected, well above the minimum of 680 k. With this value for RSET the pulse width of the vertical sync output pulse of the LM1881 is about 340 s. 8 Submit Documentation Feedback Copyright (c) 1995-2015, Texas Instruments Incorporated Product Folder Links: LM1881 LM1881 www.ti.com SNLS384G - FEBRUARY 1995 - REVISED JUNE 2015 Feature Description (continued) Figure 7. (a) Composite Video; (b) Composite Sync; (c) Vertical Output Pulse; (d) Odd and Even Field Index; (e) Burst Gate or Back Porch Clamp 7.3.3 Odd and Even Field Pulse An unusual feature of LM1881 is an output level from Pin 7 that identifies the video field present at the input to the LM1881. This can be useful in frame memory storage applications or in extracting test signals that occur in alternate fields. For a composite video signal that is interlaced, one of the two fields that make up each video frame or picture must have a half horizontal scan line period at the end of the vertical scan--that is, at the bottom of the picture. This is called the "odd field" or "even field". The "even field" or "field 2" has a complete horizontal scan line at the end of the field. An odd field starts on the leading edge of the first equalizing pulse, whereas the even field starts on the leading edge of the second equalizing pulse of the vertical retrace interval. Figure 7(a) shows the end of the even field and the start of the odd field. To detect the odd and even fields the LM1881 again integrates the composite sync waveform (Functional Block Diagram). A capacitor is charged during the period between sync pulses and discharged when the sync pulse is present. The period between normal horizontal sync pulses is enough to allow the capacitor voltage to reach a threshold level of a comparator that clears a flip-flop which is also being clocked by the sync waveform. When the vertical interval is reached, the shorter integration time between equalizing pulses prevents this threshold from being reached and the Q output of the flip-flop is toggled with each equalizing pulse. Because the half-line period at the end of the odd field will have the same effect as an equalizing pulse period, the Q output will have a different polarity on successive fields. Thus by comparing the Q polarity with the vertical output pulse, an odd and even field index is generated. Pin 7 remains low during the even field and high during the odd field. Submit Documentation Feedback Copyright (c) 1995-2015, Texas Instruments Incorporated Product Folder Links: LM1881 9 LM1881 SNLS384G - FEBRUARY 1995 - REVISED JUNE 2015 www.ti.com Feature Description (continued) 7.3.4 Burst or Back Porch Output Pulse In a composite video signal, the chroma burst is located on the back porch of the horizontal blanking period. This period, approximately 4.8 s long, is also the black level reference for the subsequent video scan line. The LM1881 generates a pulse at Pin 5 that can be used either to retrieve the chroma burst from the composite video signal (thus providing a subcarrier synchronizing signal) or as a clamp for the DC restoration of the video waveform. This output is obtained simply by charging an internal capacitor starting on the trailing edge of the horizontal sync pulses. Simultaneously the output of Pin 5 is pulled low and held until the capacitor charge circuit times out--4 s later. A shorter output burst gate pulse can be derived by differentiating the burst output using a series C-R network. This may be necessary in applications which require high horizontal scan rates in combination with normal (60 Hz-120 Hz) vertical scan rates. 7.4 Device Functional Modes 7.4.1 Operation Mode In the normal operation mode, the LM1881 will extract video timing information and split the data up into the respective signals. The LM1881 will output four sync signals including the composite sync, a vertical sync pulse, a burst gate or back porch clamp pulse, and an odd and even output. The outputs from the LM1881can be used to gen-lock video camera/VTR signals with graphics sources, provide identification of video fields for memory storage, recover suppressed or contaminated sync signals, and provide timing references for the extraction of coded or uncoded data on specific video scan lines. 10 Submit Documentation Feedback Copyright (c) 1995-2015, Texas Instruments Incorporated Product Folder Links: LM1881 LM1881 www.ti.com SNLS384G - FEBRUARY 1995 - REVISED JUNE 2015 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information Apart from extracting a composite sync signal free of video information, the LM1881 outputs allow a number of interesting applications to be developed. As mentioned above, the burst gate or back porch clamp pulse allows DC restoration of the original video waveform for display or remodulation on an R.F. carrier, and retrieval of the color burst for color synchronization and decoding into R.G.B. components. For frame memory storage applications, the odd and even field lever allows identification of the appropriate field ensuring the correct read or write sequence. The vertical pulse output is particularly useful since it begins at a precise time--the rising edge of the first vertical serration in the sync waveform. This means that individual lines within the vertical blanking period (or anywhere in the active scan line period) can easily be extracted by counting the required number of transitions in the composite sync waveform following the start of the vertical output pulse. The vertical blanking interval is proving popular as a means to transmit data which will not appear on a normal T.V. receiver screen. Data can be inserted beginning with line 10 (the first horizontal scan line on which the color burst appears) through to line 21. Usually lines 10 through 13 are not used which leaves lines 14 through 21 for inserting signals, which may be different from field to field. In the U.S., line 19 is normally reserved for a vertical interval reference signal (VIRS) and line 21 is reserved for closed caption data for the hearing impaired. The remaining lines are used in a number of ways. Lines 17 and 18 are frequently used during studio processing to add and delete vertical interval test signals (VITS) while lines 14 through 18 and line 20 can be used for Videotex/Teletext data. Several institutions are proposing to transmit financial data on line 17 and cable systems use the available lines in the vertical interval to send decoding data for descrambler terminals. Because the vertical output pulse from the LM1881 coincides with the leading edge of the first vertical serration, sixteen positive or negative transitions later will be the start of line 14 in either field. At this point simple counters can be used to select the desired line(s) for insertion or deletion of data. 8.2 Typical Applications 8.2.1 Video Line Selector The circuit in Figure 8 puts out a singe video line according to the binary coded information applied to line select bits b0-b7. A line is selected by adding two to the desired line number, converting to a binary equivalent and applying the result to the line select inputs. The falling edge of the LM1881's vertical pulse is used to load the appropriate number into the counters (MM74C193N) and to set a start count latch using two NAND gates. Composite sync transitions are counted using the borrow out of the desired number of counters. The final borrow out pulse is used to turn on the analog switch (CD4066BC) during the desired line. The falling edge of this signal also resets the start count latch, thereby terminating the counting. The circuit, as shown, will provide a single line output for each field in an interlaced video system (television) or a single line output in each frame for a non-interlaced video system (computer monitor). When a particular line in only one field of an interlaced video signal is desired, the odd and even field index output must be used instead of the vertical output pulse (invert the field index output to select the odd field). A single counter is needed for selecting lines 3 to 14; two counters are needed for selecting lines 15 to 253; and three counters will work for up to 2046 lines. An output buffer is required to drive low impedance loads. Submit Documentation Feedback Copyright (c) 1995-2015, Texas Instruments Incorporated Product Folder Links: LM1881 11 LM1881 SNLS384G - FEBRUARY 1995 - REVISED JUNE 2015 www.ti.com Typical Applications (continued) Figure 8. Video Line Selector 8.2.1.1 Design Requirements The design must have a single line output in an interlaced video system. The use case can be used for televisions of computer monitors. 8.2.1.2 Detailed Design Procedure For the composite input pin, a 510-pF capacitor and 620- resistor are selected to create a lowpass filter for 500 kHz. For Rset, a 680-k was selected to allow for the Vertical Default Sync Delay Time to be set for 64 uS. Please refer to Figure 2 for Rset value selection. 12 Submit Documentation Feedback Copyright (c) 1995-2015, Texas Instruments Incorporated Product Folder Links: LM1881 LM1881 www.ti.com SNLS384G - FEBRUARY 1995 - REVISED JUNE 2015 Typical Applications (continued) 8.2.2 Multiple Contiguous Video Line Selector With Black Level Restoration The circuit in Figure 9 will select a number of adjoining lines starting with the line selected as in the previous example. Additional counters can be added as described previously for either higher starting line numbers or an increased number of contiguous output lines. The back porch pulse output of the LM1881 is used to gate the video input's black level through a lowpass filter (10-k, 10-F) providing black level restoration at the video output when the output selected line(s) is not being gated through. Figure 9. Multiple Contiguous Video Line Selector With Black Level Restoration 8.2.2.1 Design Requirements The design will select a number of adjoining lines starting with the line selected in the previous application example. 8.2.2.2 Detailed Design Procedure Another MM74C193N counter is added to the design to support the additional line outputs. A 10-k resistor and 10-uF capacitor is added to the output of the BURST/BLACK Porch pin to create a low pass filter which adds in black level restoration to the video. For the composite input pin, a 510-pF capacitor and 620- resistor are selected to create a lowpass filter for 500 kHz. For Rset, a 680-k was selected to allow for the Vertical Default Sync Delay Time to be set for 64 uS. Please refer to Figure 2 for Rset value selection. 9 Power Supply Recommendations The LM1881 is designed to operate from an input voltage supply range between 5 VDC and 12 VDC. The LM1881 requires external a decoupling capacitor at Pin 8 and another at Pin 6. Submit Documentation Feedback Copyright (c) 1995-2015, Texas Instruments Incorporated Product Folder Links: LM1881 13 LM1881 SNLS384G - FEBRUARY 1995 - REVISED JUNE 2015 www.ti.com 10 Device and Documentation Support 10.1 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2ETM Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 10.2 Trademarks E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. 10.3 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 10.4 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 11 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 14 Submit Documentation Feedback Copyright (c) 1995-2015, Texas Instruments Incorporated Product Folder Links: LM1881 PACKAGE OPTION ADDENDUM www.ti.com 18-May-2015 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM1881M NRND SOIC D 8 95 TBD Call TI Call TI 0 to 70 LM 1881M LM1881M/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM 1881M LM1881MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM 1881M LM1881N/NOPB ACTIVE PDIP P 8 40 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 70 LM1881N (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 18-May-2015 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 19-May-2015 TAPE AND REEL INFORMATION *All dimensions are nominal Device LM1881MX/NOPB Package Package Pins Type Drawing SOIC D 8 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 12.4 Pack Materials-Page 1 6.5 B0 (mm) K0 (mm) P1 (mm) 5.4 2.0 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 19-May-2015 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM1881MX/NOPB SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2016, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM1881M LM1881M/NOPB LM1881MX LM1881MX/NOPB LM1881N LM1881N/NOPB