Switches Push Button Specifications: Maximum current/voltage rating with resistive load : 400mA 32V ac, 100mA 50V dc and 125mA 125V ac. Maximum initial contact resistance : 50m. Minimum insulation resistance : 1G at 500V dc. Dielectric strength : 1000V ac rms. Electrical life at full load : 500,000 cycles. Panel Thickness: -B1 series : 0.8mm (0.031) minimum and1.8mm (0.071) maximum. -B2 series : 1.5mm (0.059) minimum and 4mm (0.157) maximum. Total travel : 1.5mm (0.59). Operating force : 2N to 5N. Contact bounce : 10ms. Mechanical life : 1,000,000 cycles. Maximum torque : 1.5Nm applied to nut. Maximum soldering : 300C for 3 seconds. Switch Function Switch Function Number Poles Connected Terminals Position 1 Position 2 Position 1 Position 2 OFF MOM OPEN 1-3 SP Pole Options Schematic Model Number PAS6 Features: * * * * Eight plunger colours. Flat plunger top allowing marking. Antirotation bushing. New solder lug terminal. Dimension : Millimetres (Inches) http://www.farnell.com http://www.newark.com http://www.cpc.co.uk Page <1> 26/11/08 V1.1 Switches Push Button Snap-in Mounting Panel Thickness : 0.8mm to 1.8mm Dimension : Millimetres (Inches) Mounting by Threaded Bushing Panel Thickness : 1.5mm to 4mm Dimension : Millimetres (Inches) Soldering Processes: Manual soldering : Use soldering iron of 30 watts, controlled at 350C approximately 5 seconds while applying solder. Wave soldering : Recommended soldering temperature : 260 5C Duration of solder Immersion : 5 1 seconds (PCB is 1.6mm in thickness). Soldering : Vapor phase. http://www.farnell.com http://www.newark.com http://www.cpc.co.uk Page <2> 26/11/08 V1.1 Switches Push Button Temperature Profile Zone Room Temperature (C) Time (Seconds) Pre-heat (A) 150 Minimum 120s Soak (B) 180 to 200 Minimum 150s Peak (C) 200 to 235 Minimum 30s Peak (D) 235 to 260 Minimum 40s Peak (E) 260 Maximum 10s Part Number Table Description Part Number MCPAS6B1M1CE7 MCPAS6B1M1CE2 MCPAS6B1M1CE3 MCPAS6B1M1CE6 MCPAS6B1M1CE5 Switches MCPAS6B2M1CE7 MCPAS6B2M1CE2 MCPAS6B2M1CE3 MCPAS6B2M1CE6 MCPAS6B2M1CE5 http://www.farnell.com http://www.newark.com http://www.cpc.co.uk Page <3> 26/11/08 V1.1 Switches Push Button Part Number Explanation: MCPAS6 B1 M1 C E Model Number Bushing Terminations Contact Material Seal Bushing Terminations Contact Material Seal ROHS Soldering Cap Colour : : : : : : 7 ROHS Soldering Cap Colour B1 = Snap-in, B2 = Threaded Bushing. M1 = Solder Lug. C = Gold Over Silver. E = Epoxy (std). Rohs Compliant. 7 = Blue, 2 = Black, 3 = Red, 6 = Green and 5 = Yellow. Disclaimer This data sheet and its contents (the "Information") belong to the Premier Farnell Group (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. SPC Multicomp is the registered trademark of the Group. (c) Premier Farnell plc 2008. http://www.farnell.com http://www.newark.com http://www.cpc.co.uk Page <4> 26/11/08 V1.1