8 6 i, 3 DRW NO. SH REV v C -1.67-5010-500 1] BACKPLANE POLARIZING/GUIDANCE MODULE ZONE REV SCR NO. DESCRIPTION BY DATE APPROVED ASSEMBLY PART NUMBER ASSIGNMENT - A 29474 NEW RELEASE SV 11/23/99 | D.Provencher L67-X 0 X X- xX xX X _ B 34,915 ADDED MAT TOD STEN ISG 5/9/01 LEBLANC Fe ee CAD LEAD FREE LL svewat covract Loan (See TABLE 2) - C 30370 ADDED VHDM TO TITLE so | 8/0102 YEH 5 = UNIFORM LOAD, 702X (PIN LENGTH) 6 = UNIFORM LOAD, BRUSH 60 T= 4.75 - D 40819 MODIFIED TABLE 11! SG 1/7/02 WLI 7 = CUSTOM LOAD LEADED 2 8 = ADVANCE MATE UNIFORM LOAD 702X 50 % - E 4.1020 ADDED TABLE V SG 1/27/03 W.LI L = CUSTOM LOAD, LEADED, ADVANCED PLATING PLATING CODE @ - F WLII-SV6MHP.VERO1 REVISE DATUMS AND ADDED TABLE VI SG/ML 02/09/04 W LI D N = CUSTOM LOAD, LEAD FREE, ADVANCED PLATING 0-735 b-80L 1 = 73? 5=803 G KLEC-66RSE5.VERO1 ADDED NOTES 17 & 18 SG 9/20/04 LEBLANC 2 = 769 6=806 NO. OF POSN POLARIZING 3. = 768.~7=805 Kx (oo) = (1) 3] H | DMAG-6BSMYQ.VERO1 ADDED LEAD FREE PLATING OPTION GKR | 05/03/05 S.BAIR = 25 POSN PIN LOCATION 7 - > 8 | 25 = 25 POS CODE(SEE TABLE 4) SEF TABLE 1 J MLEE-6KBPQ3.VERO1 REPLACED DRAW ING FORMAT ML 01/20/06 C.SAMMIS TABLE 5 (EH 1.00 . K | SBAR-6NHL4J.VERO1 Seo ND rapLe gett 3 HCL | 04771706 | K.LEBLANC ASSEMBLY BACKPLANE POLARIZING ae TOTAL NUMBER OF | TOTAL NUMBER OF gui e AND EN nat Nuit , - 464 _ ADDED NEW PART, NUMBERS FOR NEW PLATING CODES PART NUMBER | GUIDANCE MopULE | | ) | P | signal CONTACTS | GROUND SHIELDS STANDARD GUIDE PIN | 364-0383-553 19.3 : TL w L_ | CSAS-82ZPTE.VERO' Meee MLETeD TABLE Ge HCL-MH | 0370172010 | C.SAMMIS 467-X010-XXX 467-0010-070 9 (18.00) | 27.0 40 10 CUSTOM GUIDE PIN 564-0420-553 47.3 - : \ MODIFIED NOTE 6 AND 7. 467-X025-XXX 467-0025-070 24 | (48.00) |57.0 100 25 CUSTOM GUIDE PIN 564-0487-553 13.4 - 2.25 to . 015 TABLE 2 STANDARD POL PIN 564-0440-553 - 10.4 ROW A (| | | \ [ ASSEMBLY PART NUMBER SIGNAL CONTACTS CONTACT LENGTH TABLE 3 ap { 467-(3,5,8)0XX-XX1_ | 260-0022- 4.75 ASSEMBLY SHIELD CONTACTS ! GA Xx D PART NUMBER SEE DETAIL W SH 2| SHIELD HEIGHT 14.5 (8.00) % | 6.85 467-(3,5,8)0XX-XX2 | 260-0021- O 6.25 1,67 -30XX-XXX NZA N/A oN _ - - - NJ 467-(3,5,8)0XX-XX4 | 260-0024 22 5.15 167-60XX-XXX| 272-0001. OD 53 TaT16 SOK KKD 1 260-0000 ch | EE i67-B0xx-xHX] 272-0024 | 5.5 ) cM: 467-90XX-XXX | 272-0004- 5.5 DB .00 467-(6,9)0XX-XX3 | 260-0003- & 4.25 @ 2.254 /_ 467-(6,9)0XX-XX4 | 260-0004- 5.15 Te to oxyfrool- te C TA i, SEE TABLE 1 BLE oO 0.39 + PART NUMBER - P - 167 -XOXX-( -OXX -~AXX -BXX -C XX -DXX | -EXX -~FXX -GXX -~-HXX POLARIZING PIN ORIENTATION 7 <____ 1,1 > + e 0.25 GUIDE PIN <q [D}q : +3.68 e 0.40 rN 0.40 y~ D0.30W JAC |B @ [0.40 JA |C 1 [0.35 [A [B SHIELD \ OLARIZING PIN GJ MATING SURFACE 4..75+0.10 INSULATOR N 4. .25+0.10 SEE TABLE 1 | | n\ SIGNAL CONTACT Oy MATING SURFACE CONTACT LENGTH SEE TABLE 5 BACKPLANE INSULATOR SFE TABLE 2 & ' TOP REFERENCE Uf DETAIL U \K IL SHIELD HEIGHT { bt 8 DETAIL U SEE TABLE 3 - SCALE 6/1 DETAIL kK SEE TABLE 2? SCALE 12/1 1 \ os ) N0 0H i) a a ' ~. NOTES: G POLARIZING PIN MUST ALIGN AS INDICATED BY PART NUMBER CODE. (SEE TABLE 4). L ~ TO INSURE PROPER ALIGNMENT, THE OCTAGONAL BASE PORTION OF THE PIN MUST BE POSITIONED INTO THE CORRESPONDING MOLDED CAVITY. WHEN ASSEMBLED TO BACKPLANE INSULATOR, CONTACTS MUST SEAT FLUSH WITH INSULATOR'STOP SURFACE TO A MAXIMUM ALLOWABLE GAP OF 0.25MM. 25 Z 0.12 SQ SHIELDS SHALL BE STRAIGHT WITH MAXIMUM ALLOWABLE BOW OF 0.15 MILLIMETERS ON EITHER SIDE OF SHIELD. SEE DETAIL X. SEE SHEET 2. (TAIL LENGTH) 1B0.25 IF lE |G OPEN NOTCH END DESIGNATES COLUMN 1. / PART MARKING AS FOLLOWS: LINE 4; ATCSYYWWDHH (LOGO, YEAR. WEEK, DAY, HOUR) SEE DETAIL K SEE DETAIL L 8.00 LINE 2. MODULE PART NUMBER (467 ash###HH), = LINE 3. WORK ORDER NUMBER (VHod#HHHH), WHERE * DENOTES MANUFACTURING LOCATION. 139 : SECTION Z-Z z IF MODULE PART NUMBER IS 467-7XXX-XXX OR &467-2XXX-XXX OR &60-LXXX-XXX OR &460-NXXX-XXX, PART REVISION, MODULE ORIENTATION, rv 0.25 Q ~ z NUMBER OF COLUMNS, PLATING CODE, AND SIGNAL CONTACT LOAD ARE NOT APPLICABLE. SECTION XX HI MAX ce @ LAST 3 DIGITS OF THE SIGNAL CONTACT AND SHIELD CONTACT PART NUMBERS ARE SELL IUN A-A DETERMINED BY PLATING CODE. MATCHED PLATING DEFINED BY THE 9th DIGIT OF ASSEMBLY PART NUMBER. - 735 - Ni SULFAMATE, STANDARD GOLD, LEADED L 732 - Ni SULFAMATE, HIGH GOLD, LEADED i oO 769 - Ni SULFAMATE, STANDARD GOLD, LEAD-FREE Ss 768 - Ni SULFAMATE, HIGH GOLD, LEAD-FREE 804 - NANO Ni, STANDARD GOLD, LEADED 2 6h ra 803 - NANO Ni, HIGH GOLD, LEADED S 806 - NANO Ni, STANDARD GOLD, LEAD-FREE 805 - NANO Ni. HIGH GOLD, LEAD-FREE TOLERANCES DESIGN 7/7799 (8) FOR HASL ONLY, PTH TO BE G0.610-0.495MM, BASE OF PLASTIC JSG Amphenol TCS Y. ROUTE DIFFERENTIAL PAIRS THROUGH A-B AND D-E INSULATOR 0.0 +0.25 [ppawn 675/99 A Division of Amphenol Corporation 2 10. DATUM -A- |S DEFINED AS THE WAFER MATING SURFACE OT THE PLASTIC INSULATOR. J.Varhegyi 200 Innovative Way, Neshua, NH 03062 603.879.9000 = 1. DATUM -B- IS DEFINED AS THE CENTERLINE OF THE TOP OF THE OUTERMOST WAFER SLOTS IN THE INSULATOR WALLS. 0.00 [49-3 | es THLE 12. DATUM -C- IS DEFINED AS THE CENTERLINE OF THE CONNECTOR MEASURED FROM THE TWO OUTERMOST ROWS OF SIGNAL CONTACT HOLES. - D h a 13. DATUM -E- IS DEFINED AS THE CENTERLINE OF THE CONNECTOR MEASURED FROM THE TWO OUTERMOST COLUMNS OF SIGNAL CONTACTS TAIL SIDE. 0.000 | D Provencher | BACKPLANE POLARIZING/GUIDANCE M = | 14. DATUM -F- IS DEFINED AS THE BOTTOM SURFACE OT THE PLASTIC INSULATOR. aNGles Je |? A7em00 15. DATUM -G- IS DEFINED AS THE CENTERLINE OF THE CONNECTOR MEASURED FROM THE TWO OUTERMOST ROWS OF SIGNAL CONTACTS TAIL SIDE. 9.00 <Q __ Provencher | part NO cer DART NUMBER TREE Fey 16. NZA UNLESS OTHERWISE SPECIFIED DIMENSIONS cry USING GUIDE PINS THAT ARE SHORTER THAN THE STANDARD HEIGHT OF 19.3mm AND POLARIZING PINS THAT ARE SHORTER THAN THE STANDARD 4 |G0.25 |F IE |G ARE IN MM, DECIMAL MARKER |S A PERIOD) OWING NO. REV HEIGHT OF 12.6mm MAY NOT PROVIDE THE SUFFICIENT X AND Y AXIS ALIGNMENT AND POLARIZING PROTECTION PRIOR TO COMMENCEMENT OF ALL {} ( -467-5010-500 L COMPONENT MATING SEQUENCES. CONSULT TERADYNE APPLICATIONS ENGINEERING PRIOR TO SYSTEMS DESIGN AND COMPONENT SELECTION. DETAIL L CUSTOMER USE F101 ASSY-BPc1o-RIGHTEUIDEcaRD | 17 (18) STANDARD GUIDE PIN (564-0385-553) AND STANDARD POLARIZING PIN (564-0387-540) ARE IN STANDARD 5000 SERIES MODEL ASSEMBLIES. ANY GUIDE SCALE 12/1 TERPRET PER ASME 14 SN Prove type: PIOG-ASSY-BP-10-RIGHTGUIDE-BRO | 1.17 PIN OR POLARIZING PIN OTHER THAN THESE STANDARD NUMBERS WILL RESULT IN CUSTOM 7XXX OR 2XXX OR LXXX OR NXXX SERIES MODULE ASSEMBLIES BEING ASSIGNED. DRAW ING CODE IDENT 31413 SIZE 0D SCALE 3/1 SHEET 1 OF 2 8 7 6 5 4 3 2 '8 7 6 l, 3 DRW NO. SH REV | v C -4.67-5010-500 2 | ZONE |REV SCR NUMBER DESCRIPTION BY DATE APPROVED SEE SHEET 1 SEE DETAIL X _ 2.00 4 [10.00] KR OLARIZING PIN fo SHOWN IN POSITION A ' D SIGNAL CONTACT | DGE OF SHIELD POSITION 1 ROW A a2 | 7 yt oO 7 oe / e | . ao \\ cM To . \_ im VY DAUGHTERC ARD a PLATED THROUGH HOLES SEATED THROUGH HOLE - CONNECTOR SIDE DETAIL X NO SCALE AUGHTERC ARD 7 CONNECTOR SIDE + Kx [2.00]= (Ll) KE mal POSITION 1 SEE TABLE 7 SHEET 1 _ ROW A [7 , - + |10.00) KR } '+ (7.00) 4 2.25 r P L J > 1.754 Ki _ SIGNAL ROW iz p 14.36 4.75 NS r | -- ae ROW A & 7 -- -- _- xX it Bd | L -- @-- GROUND ROW 8.00 ; <q , - -- -- (ROW C) | ; P L J y H Hl ry : L 2.25 | sausarecaro | FY PAY SAY I 4 0 0.6457 SIGNAL CONTACT . O : 0.51b | pb |BO.10 |X }Y | 0.660[0.026] DRILL f | (0.41) OFFSET -_+4 - 0.75 1.00 PA 1.00 PAD SIGNAL ROW ADJACENT SIGNAL/SHIELD SEE DETAIL V | COLUMN FOR CONTINUOUS GRID B BACKPLANE HOLE PATTERN | SIGNAL WITH GUIDANCE CONNECTOR SIDE 0.41 OFFSET " . ya NI) |S |GNAL ROW A (POLARIZING PIN Nall lal | NOT SHOWN) MIT DNT DIT BIT DIT. | 7 3 | VV We i Lh { 2 = INNIS | 7]\ G BACKPLANE SHIELD Vy ' v eye 8 t L h oa 7 =| 1.80 MIN z = Y BOARD THICKNESS dn ) ) SECTION _Y-Y SECTION Z-Z = SCALE 4/1 i BACKPLANE oO ) ( ~ SIGNAL PIN Hn, ak He, S 4 DESIGN 7/7799 1 SS > 2> t ( | AM A AG A TOLERANCES ISG Amphenol TCS . 0.0 0.25 prawn 8/5/99 A Division of Amphenol Corporation 2 2.09 | | = = NININIS "Tay . 5.5 -Varnedyl 200 Innovative Way, Nashua, NH 08062 603.879.3000 t 3.64 IN IN IN | 0.00 +0.13 CHK ADB TITLE = pe? fm Te F 0.000 |+ - D.Provencher} BACKPLANE POLARIZING/GUIDANCE M |-2 + APVD 4/26/00 ASSEMBLY, RIGHT, 5 ROW HSD = =e ACKPLANE ANGLES |= - D .Provencher PART NO. REV satu ee RETALL eu BE ou 2 ens PART NUMBER TREE | WA 212-0001-XXX SCALE 6/1 DRAW ING NO. REV DETAIL W ADVANCE MATE SHIELD } ( -467-5010-500 L 272-0004-XXX CUSTOMER USE Pro/E type: P1018-ASSY-BP-10-RIGHTGUIDE-BRD | 1.17 INTERPRET PER ASME Y14.5M Pro/E DRAWING: C-467-5070-500 | L.0O DETAIL W DRAW ING CODE IDENT 31413 SIZE 0D SCALE 3/1 SHEET 2 OF 2 8 7 6 A . 3 2