NPN small signal transistor BCX19 Dimensions (Unit : mm) Features (1) High gain and low saturation voltage. (2) Complements the BCX17. 2.9 0.4 (3) Package 1.3 2.4 Packaging specifications Type 0.95 0.45 0.2Min. BCX19 Taping Code T116 Basic ordering unit (pieces) 3000 (2) (1) 0.95 0.95 0.15 1.9 (1)Emitter BCX19 (2)Base Each lead has same dimensions (3)Collector Abbreviated symbol : GU1 Absolute maximum ratings (Ta=25C) Symbol Limits Unit Collector-emitter voltage (VBE=0) VCES 50 V Collector-emitter voltage (open base) VCEO 45 V Emitter-base voltage Parameter VEBO 5 V Collector current IC 0.5 A Collector current (peak value) ICM 1 A 0.2 W Collector power dissipation PC 0.35 W 0.425 W 2 Junction temperature Tj 150 C Storage temperature Tstg -65 to 150 C Mounted on a 7x5x0.6 mm CERAMIC SUBSTRATE 2 Mounted on a 15x15x0.6 mm CERAMIC SUBSTRATE Electrical characteristics (Ta=25C) Min. Typ. Max. Unit Collector-emitter breakdown voltage BVCES 50 - - V IC= 50A Collector-emitter breakdown voltage BVCEO 45 - - V IC= 10mA BVEBO 5 - - V IE= 50A Collector-base cutoff current ICBO - - 0.1 A VCB= 20V Emitter-base cutoff current IEBO - - 10 A VEB= 5V Parameter Emitter-base breakdown voltage Symbol Conditions Collector-emitter saturation voltage VCE(sat) - - 0.62 V IC/IB= 500mA/ 50mA Base-emitter voltage VBE(on) - - 1.2 V VCE= 1V, IC= 500mA 100 - 600 DC current transfer ratio Transition frequency Collector-base cutoff current VCE= 1V, IC= 100mA 70 - - 40 - - fT - 250 - MHz ICBO - - 5 A hFE www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. - VCE= 1V, IC= 300mA VCE= 1V, IC= 500mA 1/2 VCE= 5V, IE= 20mA, f=100MHz VCB= 20V, Ta=150C 2011.09 - Rev.B Data Sheet BCX19 Absolute maximum ratings (Ta=25C) IB =500uA IB =450uA 1000 VCE=1V Ta=125C 75C 25C -55C 10 IB =300uA 80 IB =250uA 60 IB =200uA IB =150uA 40 IB =100uA 20 100 VCE=5V 3V 1V IB =50uA IB =0A 1 0 0.2 0.4 0.6 0.8 1 1.2 BASE TO EMITTER VOLTAGE : VBE (V) 0.4 100 Ta=125C 75C 25C -55C 10 1000 COLLECTOR CURRENT : IC (mA) COLLECTOR SATURATION VOLTAGE : VCE(s at) (V) VCE=1V 100 1.6 10 Ta=25C IC /IB=50/1 20/1 10/1 0.1 0.01 1 10 100 1000 COLLECTOR CURRENT : IC (mA) Fig3. DC Current Gain vs. Collector Current (I) 100 1000 1 IC /IB=10/1 Ta=125C 75C 25C -55C 0.1 0.01 1 10 100 1000 COLLECTOR CURRENT : IC (mA) Fig5. Collector Saturation Voltage vs. Collector Current (I) Ta=25 C f=1MHz IE=0A 50 1 2 1 Fig4. DC Current Gain vs. Collector Current (II) 20 Cob 5 COLLECTOR CURRENT : IC (mA) Fig6. Collector Saturation Voltage vs. Collector Current (II) Ta=25 C VCE=6V 500 TRANSITION FREQUENCY : fT (MHZ) Cib 10 1.2 Fig2. Grounded Emitter Output Characteristics 1000 10 0.8 COLLECTOR TO EMITTER VOLTAGE : VCE (V) Fig1. Grounded Emitter Propagation Characteristics 1 10 Ta=25C 0 COLLECTOR SATURATION VOLTAGE : VCE(s at) (V) 0 DC CURRENT GAIN : hFE Ta=25C IB =350uA DC CURRENT GAIN : hFE 100 COLLECTOR OUTPUT CAPACITANCE : Cob (pF) EMITTER INPUT CAPACITANCE : Cib (pF) IB =400uA 100 COLLECTOR CURRENT : IC (mA) COLLECTOR CURRENT : IC (mA) 1000 200 100 0.1 0.2 0.5 1 2 5 10 20 -1 -2 -5 -10 -20 COLLECTOR TO BASE VOLTAGE : VCB (V) EMITTER TO BASE VOLTAGE : VEB (V) EMITTER CURRENT : IE (mA) Fig.7 Input-and-output capacity vs.voltage characteristic Fig.8 Transition frequency vs.emitter current www.rohm.com c 2011 ROHM Co., Ltd. All rights reserved. 2/2 -50 2011.09 - Rev.B Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com (c) 2011 ROHM Co., Ltd. All rights reserved. R1120A