Analog Resistive Touch Screen Controller TSC-40/IC product specification TSC-40/IC Product Specification Table of Contents 1. PRODUCTS OUTLINE ................................................................................................. 2 1-1. Scope of Application................................................................................................................... 2 1-2. Outline......................................................................................................................................... 2 1-3. Features ...................................................................................................................................... 2 1-4. General specification................................................................................................................... 3 2. Pin layout and representation ........................................................................................ 4 3. Pin functions ............................................................................................................... 5 4. Initial setting ................................................................................................................ 7 4-1. EEPROM setting ......................................................................................................................... 7 4-2. Touch screen mode setting ........................................................................................................ 7 4-3. Power supply voltage setting...................................................................................................... 7 5. Data sheet .................................................................................................................. 8 5-1. Absolute maximum rating ........................................................................................................... 8 5-2. Recommended operational conditions......................................................................................... 9 5-3. Timing requirement ................................................................................................................... 10 5-4. DC standards............................................................................................................................ 11 6. Packaging Specification.............................................................................................. 12 6-1. Outline....................................................................................................................................... 12 6-2. Notes on storage/handling ........................................................................................................ 12 6-3. Basic packaging........................................................................................................................ 12 6-4. Small group packaging ............................................................................................................. 13 6-5. Tray specification ...................................................................................................................... 14 6-6. Product name label specification .............................................................................................. 14 7. Storage Specification ................................................................................................. 15 7-1. Storage Conditions.................................................................................................................... 15 7-2. Baking ....................................................................................................................................... 15 8. Implementation Temperature Specification ................................................................... 16 9. Terminal Pin Specification........................................................................................... 17 10. Cleaning ................................................................................................................. 17 11. Changes and improvements ...................................................................................... 18 11-1. Version history ........................................................................................................................ 18 12. Warranty ................................................................................................................. 19 12-1. Warranty Period ...................................................................................................................... 19 12-2. Warranty Target ...................................................................................................................... 19 12-3. Warranty Exceptions ............................................................................................................... 19 13. Notes on use ........................................................................................................... 20 13-1. Overall handling ...................................................................................................................... 20 13-2. Others ..................................................................................................................................... 20 Dimensional Drawing Circuit Diagram Document No. DER-S0100A 1 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 1. PRODUCTS OUTLINE 1-1. Scope of Application This specification applies to the TSC-40/IC. 1-2. Outline TSC-40/IC is an analog touch screen control IC that performs A/D conversion on analog signal for the 4-wire and 5-wire resistive analog touch screen, and transmits coordination data with 10bit resolution to the host in a 9600bps serial (asynchronous). The serial communication enables a connection with PC's serial port via RS-232C I/F circuit or TTL level. At the coordinate detection, internal filtering process provides a stabilized coordinate value. By using the correction function, in addition to the losses that occur in the circuit, display deflection between touch screen input point that occur in each element and indicator cursor can be corrected to adjust the display position. 1-3. Features Two coordinate output modes are provided and selected per application: "Coordinate data mode" where coordinate information is sent with 10bit resolution as it is, and "correction data mode" where read coordinate is converted to the indicator's display coordinate and sent. "Correction data mode" is available after EEPROM is externally attached. It enables to set up to nine correction points. Coordinate data can be corrected with the base of correction points. Using this function allows the host driver to make the implementation of correction function unnecessary. In addition, by placing correction points at the touch screen center and center points of four edges of touch screen, resistance value deviation of transparent electrode film can be corrected. Two external switch functions are always available in the coordinate (correction) data mode. Two pieces of external switch information are, at the transmission of coordinate data, included in the coordinate data as pen-down/pen-up information. Since in the pen-up mode, pen-up data can be always output to the host, this switch is available as a function switch. At the touch screen input, buzzer and LED outputs are available. Input confirmation via display and sound is available. When no touch screen input is performed, the state moves to "power-save mode" so that such application can be supported that requests a low power consumption. Seven types of coordinate output rates are provided and either can be selected per application among seven types: six types from 30 to 150p/s plus one type, a point mode that outputs the coordinate only one time when pen-down is performed. Document No. DER-S0100A 2 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 1-4. General specification Item Rating Power supply voltage DC 3.3V to 5.5V Power consumption 29.5mW (standard) Operating Temp -20 C to +85 C (No dew condensation) Temperature range at storing -40 C to +125 C (No dew condensation) Communication scheme Communication scheme Asynchronous, serial Communication rate 9600bps Data length 8bits Stop bit 1bit Parity None Notes Each setting is fixed Operation frequency 6MHz Fixed to 6MHz Coordinate output rate (point / second) (1) Point mode (2) 30p/s (3) 50p/s (4) 80p/s (5) 100p/s (6) 130p/s (7) 150p/s Point Mode: Only when touch screen is input, pen-down ID is sent once. After input ends, no pen-up ID is sent. Linearity error 3 LSB Input response time 10ms (TYP) 150p/s, For coordinate data mode. Coordinate resolution 10bit (1024x1024) In the correction data function, resolution follows the setting value Dimension (mm) 9x9x1.7 Document No. DER-S0100A 3 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification THI THO SXR/LR SXL/UR SYU/UL SYD/LL 23 22 21 20 19 18 17 RxD_I #### 8 32 VCC AN1 7 31 CNVSS AN0 INDEX 6 30 RST BEEP xxx 5 29 VREF SW0 4 28 EEP-DO SW1 3 27 SEL1 TxD TSC-40x 2 26 AN3 RxD 1 25 AN2 SEL0 24 2. Pin layout and representation 16 SEL4/EEP-CS 15 SEL3/EEP-CLK 14 SEL2/EEP-DI 13 LED1 12 P30 11 VSS 10 XOUT 9 XIN Marking specification TSC-40x Product number xxx ROM number #### Lot number Document No. DER-S0100A x: version number 4 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 3. Pin functions Pin number Pin name I/O 1 AN2 I/O Touch screen XL/UR input pin. 2 AN3 I/O Touch screen XR/LL input pin. 3 SEL1 I Transition select pin. H = Auto transition*1 after reset. L = transition by command. 4 EEP-DO I EEPROM DO input pin; At using no EEPROM, Vcc or GND is connected. 5 I A/D converter reference voltage input pin; Vcc is connected. 6 VREF RST I Reset input pin (active L). 7 CNVSS I Operation mode control pin; Vss is connected. 8 VCC I Power supply input pin; Vcc is connected. Functional description 9 XIN I Clock input pin; When using external clock, clock is input to this pin. 10 XOUT O Clock output pin; When using external clock, this pin is opened. 11 VSS I Power supply input pin (GND); GND is connected. 12 P30 O Opened*2. 13 LED1 O 14*3 SEL2/EEP-DI I/O 15*3 SEL3/EEP-CLK I/O 16*3 SEL4/EEP-CS I/O O LED output pin; ON = Lo, OFF = Hi. EEPROM DI signal output pin; When using EEPROM, EEPROM DI is connected. Whether or not EEPROM is used, connect with GND via resistance. EEPROM SK signal output pin; When using EEPROM, EEPROM SK is connected. Touch screen mode setting pin. (L=4-wire, H=5-wire) Whether or not EEPROM is used, connect with Vcc or GND via resistance. EEPROM setting pin shared with EEPROM CS signal output pin. EEPROM is set via resistance and Vcc or GND is connected. (L = Used, H = Not used). When using EEPROM, EEPROM CS is connected. Unused pin; Opened. 17 18 SYD/LL O Touch screen LL control pin. 19 SYU/UL O Touch screen UL control pin. 20 SXL/UR O Touch screen UR control pin. 21 SXR/LR O Touch screen LR control pin. 22 THO O Pen down detection pin. 23 THI I 24 RxD_I I 25 SEL0 I In power-save mode, start signal input pin by pen down. In power-save mode, start signal input pin by command reception. Only used serial mode, RxD is connected. If power supply voltage is 4.0 to 5.5V, GND is connected. If power supply voltage is 3.3 to 4.0V, Vcc is connected. 26 RxD I/O Data receive pin. 27 TxD I/O Data send pin. 28 SW1 I SW1 input pin *4; H = ON = 1, L = OFF = 0. 29 SW0 I SW0 input pin *4; H = ON = 1, L = OFF = 0. 30 BEEP O BEEP output pin; Hi output; Output frequency =2.5kHz, Output time =50ms. 31 AN0 I Touch screen YD/LL input pin. 32 AN1 I Touch screen YU/Sense input pin. Document No. DER-S0100A 5 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification *1: Auto transition = Mode changes by a command are not performed. It becomes a "Coordinate Data Mode (150pps)" immediately after reset. *2: Always open. If connected with VCC, VSS, or other circuit, an error operation may occur. *3: About pin number 14, 15 and 16, immediately after a power supply injection, it works as an input terminal and becomes an output terminal after that. Do not open these terminals. *4: If neither SW0 nor SW1 function is used, connect 28 and 29 pins to GND directly. Document No. DER-S0100A 6 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 4. Initial setting 4-1. EEPROM setting Depending on that calibration is performed in either TSC-40/IC or host, you can select whether EEPROM is used or not to store the correction data. EEPROM selection can be set via pin number 16, where hardware reset release enables the setting. (TSC-40/IC) VCC (EEPROM) H= Not used SEL4/EEP-CS L= Used CS 4-2. Touch screen mode setting Touch screen mode setting for 4-wire/5-wire is performed by setting pin number 15 to "H" or "L". When power supply is turned on, or hardware reset is released, pin number 15 is read to turn on in either 4-wire/5-wire mode. Mode Pin number 15 4-wire touch screen GND 5-wire touch screen Vcc 4-3. Power supply voltage setting Power supply mode setting for 3.3V/5V is performed by setting pin number 25 to "H" or "L". When power supply is turned on, or hardware reset is released, pin number 25 is read to turn on in either 3.3V mode/5V mode. Power supply voltage Mode Pin number 25 3.3 to 4.0V 3.3V mode Vcc 4.0 to 5.5V 5V mode GND *When you operate it with 3.3V mode, the inside frequency of CPU works at 3MHz, and the sampling rate is 80pps max in calibration data mode. Document No. DER-S0100A 7 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 5. Data sheet 5-1. Absolute maximum rating Item Power supply voltage Symbol Rating Minimum Maximum Unit VCC -0.3 6.5 V Input voltage VI -0.3 Vcc+0.3 V Output voltage VO -0.3 Vcc+0.3 V Power consumption 200 mW Operation temperature TOPR -20 +85 C Storage temperature TSTG -40 +125 C Document No. DER-S0100A PD 8 Description Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 5-2. Recommended operational conditions (Vcc=3.3 to 5.5V, Vss=0V, Ta=-20 to 85C, unless otherwise noted) Limits Item Symbol Unit Minimum Standard Maximum 3.3 5.0 5.5 Power supply voltage VCC Power supply voltage VSS Analog reference voltage VREF 1.8 VCC V VIH 0.8VCC VCC V VIH 0.8VCC VCC V VIL 0 0.2VCC V VIL 0 0.2VCC V VIL 0 0.16VCC V IOH (peak) -80 mA IOL (peak) 80 mA IOL (peak) 80 mA IOH (avg) -40 mA IOL (avg) 40 mA IOL (avg) 40 mA IOH (peak) -10 mA IOL (peak) 10 mA IOH (avg) -5 mA IOL (avg) 5 mA XIN 6.0 MHz "H" input voltage 0 Description V V (Pin number 1 - 4, 12 - 32) "H" input voltage RST, XIN "L" input voltage (Pin number 1 - 4, 12 - 32) "L" input voltage RST, CNVSS "L" input voltage XIN "H" total peak output current *2 (Pin number 1 - 4, 12 - 32) "L" total peak output current *2 (Pin number 1 -4, 26 - 32) "L" total peak output current *2 (Pin number 12 - 25) "H" total average output current*2 (Pin number 1 - 4, 12 - 32) "L" total average output current*2 (Pin number 1 - 4, 26 - 32) "L" total average output current*2 (pin number 12 - 25) "H" peak output current *3 (Pin number 1 - 4, 12 - 32) "L" peak output current *3 (Pin number 1 - 4, 12 - 32) "H" average output current *4 (Pin number 1 - 4, 12 - 32) "L" average output current *4 (Pin number 1 - 4, 12 - 32) Vibration frequency *1 Vcc = 4.0 to 5.5V *2 The total output current is the sum of all the currents flowing through all the applicable ports. The total average current is an average value measured over 100ms. The total peak current is the peak value of all the currents. *3 The peak output current is the peak current flowing in each port. *4 The average output current IOL(avg), IOH(avg) in an average value measured over 100ms. *5 When the oscillation frequency has a duty cycle of 50%. Document No. DER-S0100A 9 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 5-3. Timing requirement Reset (Vcc = 3.3 to 5.5V , Vss = 0V , Ta = -20 to 85C) Item Symbol RST L width tw Limits Minimum Maximum Unit Description s 2 tw RST 0.8Vcc 0.8Vcc 0.2Vcc 0.2Vcc External clock timing Item Symbol Input cycle Clock pulse width tC tWH, tWL Limits Minimum Maximum 165 70 Unit Description ns ns Clock frequency: Fixed to 6MHz tC tWH tWL 0.8VCC 0.2VCC XIN Clock input circuit Using ceramic vibrator External clock input circuit CIN XIN XIN XOUT Open XOUT COUT Document No. DER-S0100A 10 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 5-4. DC standards (Vcc=3.3 to 5.5V, Vss=0V, Ta=-20 to 85C, unless otherwise noted) Limits Item Symbol Condition Unit Minimum IOH = -5mA Output "H" voltage *1 (Pin number 1-4, 12-32) VOH Vcc = 4.0 to 5.5V IOH = -1.0mA Vcc = 3.3 to 5.5V Standard Vcc-1.5 V Vcc-1.0 IOL = 5mA 1.5 VCC = 4.0 to 5.5V Output "L" voltage *1 (Pin number1-4, 12-32) IOL = 1.5mA VOL 0.3 VCC = 4.0 to 5.5V IOL = 1.0mA IOL = 15mA (Pin number. 12 - 16) VOL VCC = 4.1 to 5.5V IOL = 1.5mA VCC = 4.1 to 5.5V Hysteresis (Pin number 12, 15, 17-26, 30) Hysteresis (Pin number 26, 28) Hysteresis (Pin number 6) Input "H" current (Pin number 1-4, 12-32) Input "H" current (Pin number 6) Input "H" current (Pin number 9) Input "L" current (Pin number 1-4, 12-32) Input "L" current (Pin number 6) Input "L" current (Pin number 9) Power supply current Document No. DER-S0100A V 1.0 VCC = 3.3 to 5.5V Output "L" voltage Maximum 2.0 V 0.3 V VT+ - VT- 0.4 V VT+ - VT- 0.5 V VT+ - VT- 0.5 V IIH VI = VCC 5.0 A IIH VI = VCC 5.0 A IIH VI = VCC IIL VI = VSS -5.0 A IIL VI = VSS -5.0 A IIL VI = VSS -4.0 Icc STOP mode 0.1 11 A 4.0 A 1.0 uA Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 6. Packaging Specification 6-1. Outline With a basic packaging unit of 2000, TSC-40/IC is packaged for the number of 2000 and its multiple using damp-proof aluminum laminate bags (Basic packaging). If the delivery quantity is less than 2000 or not multiple of 2000, or the product can not be packaged with a unit of 2000, then damp-proof aluminum laminate bags or no damp-proof packaging specification is applicable (Small group packaging). If packaged with small group packaging, the products may be dampened. Before packaging, the product shall take the baking process as specified in [Baking] defined in "TSC-40/IC Storage/Implementation Specification". 6-2. Notes on storage/handling (1) Handle the packages with care and avoid throwing and dropping them. Or, a large impact may be imposed, causing packaging material's damage, broken package or bending lead. (2) Cardboard box may be deteriorated in its strength and deformed due to storage site's humidity, stacking condition and storage duration. It is desirable to keep the storage under normal temperature/humidity (5 to 35 C, 45 to 75%RH). For warehousing, follow the FIFO principle. (3) After unpacking, be careful in handling the product to avoid electrostatic breakdown. 6-3. Basic packaging 6-3-1. Packaging type Damp-proof packaging (Aluminum laminate bag) 6-3-2. Packaging quantity specification Quantity per tray Number of trays 250 8 + 1(cover) Quantity per packages 2000 Packing sample Desiccant Tray Product name label Aluminum laminate bag Humidity indicator Packaging label Packaging label Product name label Packaging box Document No. DER-S0100A 12 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 6-3-3. Diagram for packaging box sizes L: 330 W: 152 D: 75 (mm) 6-4. Small group packaging 6-4-1. Packaging type General packaging (No damp-proof processing) 6-4-2. Packaging quantity specification Quantity per tray Number of trays 250 1 to 8 +1(cover) Packing sample Desiccant Quantity per packages 1 - 1999 Number of trays: 1 to 8 (Additionally, one dummy tray pl aced at the top for reinforcing) Air cap Product name label Antistatic bag * No sizes specified for packaging box (Cardboard box) used for transportation. * This is an example and may not be the same as supplies. Document No. DER-S0100A 13 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 6-5. Tray specification This tray is heat-proof type, allowing the heating with 125 C for 24 hours. During heating/cooling process, however, bending may occur. In baking process, to minimize the bending, heat and cool the tray by placing it on a flat plate. 6-6. Product name label specification DMC P/N: Product number (TSC-40/IC) QTY: Quantity DAC: DMC Control Number Document No. DER-S0100A 14 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 7. Storage Specification 7-1. Storage Conditions For storing the product until its implementation, it is recommended that the following storage conditions are applied: 1. Before unpacking the damp-proof package (Aluminum laminate bag) Temperature and humidity: 5 to 40 C, 20 - 80%RH Duration: Two years or less 2. After unpacking the damp-proof package (Aluminum laminate bag) For the storing duration after the damp-proof package is unpacked and before the implementation, it is recommended that the following storage conditions is to be applied: One week or less under the ambient condition: 30 C, 70%RH or less (1) Reflow method: (2) Wave soldering method: One week or less under the ambient condition: 30 C, 70%RH or less 3. Temporary storage after damp-proof package is unpacked To store again temporarily the once unpacked and unused damp-proof package, it is recommended to pack it again into another damp-proof bag with desiccant within a shorter time after opened (Around 10 minutes) as far as possible, and fold the bag's opening, followed by sealing with adhesive material such as adhesive tape, then store it under the following conditions: Temperature, humidity: 5 to 40 C, 20 - 80%RH Duration: One month or less 7-2. Baking If any condition among those 1 to 3 listed below is applicable, it is recommended to apply the baking as described below to dry the moisture the package absorbs. You may place the tray used for damp-proof packaging directly into the thermostatic chamber since the tray is heat-proof type. When placing into the chamber or after removing from it, to avoid deformation, cool the tray by placing it on the flat plate such as surface table. 1. Any condition among 1 to 3 in [7-1. Storage condition] is unsatisfied 2. Indicator's 30% Humidity Check section changes the color to lavender or pink 3. Blue color indicator of desiccant (Silica gel) changes to pink or white Baking method Temperature: 125 C Duration: 20 to 24 hours Frequency: Four times or less (Upper limit: 96 accumulative hours) Document No. DER-S0100A 15 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 8. Implementation Temperature Specification 1. Reflow method (Infrared reflow, air reflow) Frequency: Three times or less Temperature: The following device surface temperature profile is recommended. 260 C max. Package's surface temperature 255 C or above, 10-16s max. 220 C or above, 60s max. 17515 C 1 to 4 C/s 11030s Time Figure 1: Infrared reflow, air reflow temperature profile 2. Wave soldering method (Flow soldering, solder dip method) Frequency: One time or less Temperature: Following temperature profile is recommended (Set the optimal preheat temperature according to the flux type) Temperature 10s max. (Primary + Secondary flow passage duration) 260 C max. 80 to 150 C (Package surface temperature) Time Figure 2: Wave soldering temperature profile 3. Soldering iron (Manual soldering) Soldering bit's temperature: Soldering time: 370 C or lower Five seconds or less/terminal Document No. DER-S0100A 16 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 9. Terminal Pin Specification Base material :Cu Coat :Sn-1.5%Cu Thickness of coat :5um or above 10. Cleaning In case of cleaning boards with solvents after soldering, following items should be taken attention. *Administrative guidance and regulation. *Residual ionic (non ionic) contamination. *Solvent resistance of parts. Document No. DER-S0100A 17 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 11. Changes and improvements 11-1. Version history TSC-40/IC Ver0.1 (October 3, 2007) Draft release Ver0.2 (December 10, 2007) 5-3. Timing requirement External clock timing Clerk mistake was corrected. Input cycle 500ns 166ns Clock pulse 200ns 70ns "Pb Free" was added. 6-6. Product name label specification Ver0.3 (January 21, 2008) Circuit Diagram 5-Wire Resistive Touch Screen th Corrected the 15 -Pin (SEL3/EEP_CLK) to connection with Vcc via resistance. Ver1.0 (March 13, 2008) First release (Change from ver0.3) 1-4. General specification 3. Pin functions Input response time was added. Detail information was added in 22, 23, 24 pin. 9. Terminal Pin Specification was added. Document number was added. Circuit Diagram Part number was added. (Rev 2) Ver1.1 (June 30, 2008) 5-2. Recommended operational conditions (TTL input level selected) was deleted. Ver1.2 (July 2, 2008) 1-4. General specification Power supply voltage DC 2.4V to 5.5V DC 3.3V to 5.5V Ver1.3 (March 30, 2011) 5-3. External clock timing "Input cycle" (Minimum) 166ns 165ns 6-1. Outline (Small group packaging) "damp-proof aluminum laminate bags or" was added. 6-3. Basic packaging "Packing sample" was added. 6-4. Small group packaging "Packing sample" was added. 6-4. Small group packaging "This is an example and may not be the same as supplies." was added. Ver1.4 (May 25, 2012) Address has changed as Tokyo office had moved Document No. DER-S0100A 18 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 12. Warranty 12-1. Warranty Period The warranty period is limited to 1 year from the date of shipping. The warranty for the initial defection such as appearance defection is limited to 1 month. Any defected parts under proper use will be examined by the supplier and replaced by the new parts if the defection is considered to be caused by the supplier. The replacement is subject to be included in the next lot. 12-2. Warranty Target The warranty only covers the product itself and does not cover any damage to others caused by using this product. Onsite repair or replacement is not supported. We will do our best for delivery problem and product defections, but the warranty for the production line is not covered. 12-3. Warranty Exceptions Following conditions are not covered with the warranty and subject to charge. Any malfunctions and damages during transportation and transfer by the user. Any malfunctions and damages caused by a natural disaster or a fire. Any malfunctions and damages caused by static electricity Any malfunctions and damages caused by the failure of the associated equipment. If the product is remodeled, disassembled or repaired by the user. If the product is glued onto the equipment and uninstalled. Any malfunctions and damages caused by an improper usage and handling against the specifications and notes. Document No. DER-S0100A 19 Version 1.4 (c)2012 DMC Co., Ltd. TSC-40/IC Product Specification 13. Notes on use 13-1. Overall handling When using the product, do not place it close to, or make it contact with, the conductive materials such as metal. Do not touch the metal part in the product directly with your hands. Or, it may be destructed by the static electricity. If you contact, or may contact, it directly with your hand, prepare in advance the measure against static electricity. To store the product, use an appropriate packing box and keep the storage temperature range with no overload on it. In using the product or storing it, avoid the following conditions: - Conditions where water is, or may be, attached to the product. - Conditions where condensation takes place, or may take place. - In the ambience of organic solvent or acidity or contact, or where the product contacts them. Do not alter or disassemble the product. 13-2. Others This specification may be changed for improvement without prior notices. No liabilities are taken by us for any damage caused by use of this product. This product intends to be used for the standard applications (e.g. office equipment and OA devices, industrial use, communication devices, household equipment). Avoid its use where failure or malfunction directly may affect the human body or special applications where extremely high reliability is required (e.g. airline and space industries, nuclear controls, medical use for life-sustaining). Semi-conductor devices may fail in a certain possibility. Keep the safety design in your mind so that possible failure in this product shall not cause physical accidents such as injury and death, fire and other social damages. TSC-40/IC Product Specification Version 1.4: Issued at May 25, 2012 (c)2012 DMC Co., Ltd. This document is allowed to redistribute but no alteration, part or all, is prohibited. http://www.dmccoltd.com/english/ 11F Nisseki Takanawa Bldg., 2-18-10 Takanawa, Minato-ku, Tokyo 108-0074, Japan Phone: +81-3-6721-6731 (Japanese), 6736 (English) Fax: +81-3-6721-6732 Document No. DER-S0100A 20 Version 1.4 (c)2012 DMC Co., Ltd.