WP7113LVBC/D - Kingbright

DESCRIPTIONS

zThe Blue source color devices are made with InGaN

Light Emitting Diode

zElectrostatic discharge and power surge could

damage the LEDs

zIt is recommended to use a wrist band or

anti-electrostatic glove when handling the LEDs

zAll devices, equipments and machineries must be

electrically grounded

FEATURES

zLow power consumption

zPopular T-1 3/4 diameter package

zGeneral purpose leads

zReliable and rugged

zLong life - solid state reliability

zAvailable on tape and reel

zRoHS compliant

APPLICATIONS

zStatus indicator

zIlluminator

zSignage applications

zDecorative and entertainment lighting

zCommercial and residential architectural lighting

ATTENTION

Observe precautions for handling

electrostatic discharge sensitive devices

PACKAGE DIMENSIONS

WP7113LVBC/D

T-1 3/4 (5mm) Solid State Lamp

Notes:

1. All dimensions are in millimeters (inches).

2. Tolerance is ±0.25(0.01") unless otherwise noted.

3. Lead spacing is measured where the leads emerge from the package.

4. The specifications, characteristics and technical data described in the datasheet are subject to change

without prior notice.

SELECTION GUIDE

Notes:

1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.

2. Luminous intensity / luminous flux: +/-15%.

3. Luminous intensity value is traceable to CIE127-2007 standards.

Part Number Emitting Color

(Material) Lens Type Iv (mcd) @ 2mA [2] Viewing Angle [1]

Min. Typ. 2θ1/2

WP7113LVBC/D ■ Blue (InGaN) Water Clear 550 1600 20°

ABSOLUTE MAXIMUM RATINGS at TA=25°C

ELECTRICAL / OPTICAL CHARACTERISTICS at TA=25°C

WP7113LVBC/D

Notes:

1. 1/10 Duty Cycle, 0.1ms Pulse Width.

2. Rth

JA ,Rth

JS Results from mounting on PC board FR4 (pad size ≥ 16 mm2 per pad).

2. 2mm below package base.

3. 5mm below package base.

4. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033.

Parameter Symbol Value Unit

Power Dissipation PD 120 mW

Reverse Voltage VR 5 V

Junction Temperature Tj 115 °C

Operating Temperature Top -40 to +85 °C

Storage Temperature Tstg -40 to +85 °C

DC Forward Current IF 30 mA

Peak Forward Current IFM [1] 100 mA

Electrostatic Discharge Threshold (HBM) - 250 V

Lead Solder Temperature [3] 260°C For 3 Seconds

Lead Solder Temperature [4] 260°C For 5 Seconds

Thermal Resistance (Junction / Ambient) Rth JA [2] 400 °C/W

Thermal Resistance (Junction / Solder point) Rth JS [2] 230 °C/W

Parameter Symbol Emitting Color

Value

Unit

Typ. Max.

Wavelength at Peak Emission IF = 2mA λpeak Blue 465 - nm

Dominant Wavelength IF = 2mA λdom [1] Blue 470 - nm

Spectral Bandwidth at 50% Φ REL MAX

IF = 2mA Δλ Blue 22 - nm

Capacitance C Blue 100 - pF

Forward Voltage IF = 2mA VF [2] Blue 2.65 3 V

Reverse Current (VR = 5V) IR Blue - 50 uA

Temperature Coefficient of λpeak

IF = 2mA, -10°C ≤ T ≤ 85°C TCλpeak Blue 0.04 - nm/°C

Temperature Coefficient of λdom

IF = 2mA, -10°C ≤ T ≤ 85°C TCλdom Blue 0.03 - nm/°C

Temperature Coefficient of VF

IF = 2mA, -10°C ≤ T ≤ 85°C TCV Blue -3 - mV/°C

Min.

-

2.2

-

Notes:

1. The dominant wavelength (λd) above is the setup value of the sorting machine. (Tolerance λd : ±1nm. )

2. Forward voltage: ±0.1V.

3. Wavelength value is traceable to CIE127-2007 standards.

4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure.

TECHNICAL DATA

BLUE

WP7113LVBC/D

RECOMMENDED WAVE SOLDERING PROFILE

Notes:

1. Recommend pre-heat temperature of 105°C or less (as measured with a thermocouple

attached to the LED pins) prior to immersion in the solder wave with a maximum solder bath

temperature of 260°C

2. Peak wave soldering temperature between 245°C ~ 255°C for 3 sec (5 sec max).

3. Do not apply stress to the epoxy resin while the temperature is above 85°C.

4. Fixtures should not incur stress on the component when mounting and during soldering process.

5. SAC 305 solder alloy is recommended.

6. No more than one wave soldering pass.

PACKING & LABEL SPECIFICATIONS

0.5 0.50.0

-90°

-75°

-60°

-45°

-30°

-15°

75°

60°

45°

30°

0° 15°

90°

1.0 1.0

T

a

= 25 °C

SPATIAL DISTRIBUTION

0%

20%

40%

60%

80%

100%

350 400 450 500 550 600 650 700 750 800

T

a

= 25 °C

Wavelength (nm)

Relative Intensity (a. u.)

Blue

RELATIVE INTENSITY vs. WAVELENGTH

0

2

4

6

8

10

2.0 2.2 2.4 2.6 2.8 3.0 3.2

Ta = 25 °C

Forward voltage (V)

Forward current (mA)

0.0

1.0

2.0

3.0

4.0

5.0

0246810

Ta = 25 °C

Forward current (mA)

Luminous intensity normalised

at 2 mA

0

10

20

30

40

50

-40-20 0 20406080100

Ambient temperature (°C)

Permissible forward current (mA)

0.0

0.5

1.0

1.5

2.0

2.5

-40-20 0 20406080100

Ambient temperature (°C)

Luminous intensity normalised

at T a = 25 °C

Forward Current vs.

Forward Voltage

Luminous Intensity vs.

Forward Current

Forward Current Derating Curve Luminous Intensity vs.

Ambient Temperature

WP7113LVBC/D

PRECAUTIONS

Storage conditions

1. Avoid continued exposure to the condensing moisture environment and keep the product away from rapid transitions in ambient

temperature.

2. LEDs should be stored with temperature ≤ 30°C and relative humidity < 60%.

3. Product in the original sealed package is recommended to be assembled within 72 hours of opening.

Product in opened package for more than a week should be baked for 30 (+10/-0) hours at 85 ~ 100°C.

2. When soldering wires to the LED, each wire joint should be separately insulated with heat-shrink tube to prevent short-circuit contact.

Do not bundle both wires in one heat shrink tube to avoid pinching the LED leads. Pinching stress on the LED leads may damage the

internal structures and cause failure.

3. Use stand-offs (Fig.1) or spacers (Fig.2) to securely position the LED above the PCB.

4. Maintain a minimum of 3mm clearance between the base of the LED lens and the first lead

bend (Fig. 3 ,Fig. 4).

5. During lead forming, use tools or jigs to hold the leads securely so that the bending force

will not be transmitted to the LED lens and its internal structures. Do not perform lead

forming once the component has been mounted onto the PCB. (Fig. 5 )

LED Mounting Method

1. The lead pitch of the LED must match the

pitch of the mounting holes on the PCB

during component placement.

Lead-forming may be required to insure

the lead pitch matches the hole pitch.

Refer to the figure below for proper lead

forming procedures.

Note 1-3: Do not route PCB trace in the contact area between the

leadframe and the PCB to prevent short-circuits.

"

○

"

Correct mounting method " x " Incorrect mounting method

WP7113LVBC/D

PRECAUTIONARY NOTES

1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.

2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to

the latest datasheet for the updated specifications.

3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If

customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues.

4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening

liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance.

5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.

6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes

Lead Forming Procedures

1. Do not bend the leads more than twice. (Fig. 6 )

2. During soldering, component covers and holders should leave

clearance to avoid placing damaging stress on the LED during

soldering. (Fig. 7)

3. The tip of the soldering iron should never touch the lens epoxy.

4. Through-hole LEDs are incompatible with reflow soldering.

5. If the LED will undergo multiple soldering passes or face other

processes where the part may be subjected to intense heat,

please check with Kingbright for compatibility.

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Kingbright:

WP7113LVBC/D