IDTQS3861 HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT INDUSTRIAL TEMPERATURE RANGE QUICKSWITCH(R) PRODUCTS HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT DESCRIPTION: FEATURES: * * * * * IDTQS3861 The QS3861 provides a set of ten high-speed CMOS TTL-compatible bus switches. The low ON resistance (5) of the QS3861 allows inputs to be connected without adding propagation delay and without generating additional ground bounce noise. The Bus Enable (BE) signal turns the switches on. The QS3861 is characterized for operation at -40C to +85C. Enhanced N channel FET with no inherent diode to Vcc bidirectional switches connect inputs to outputs 5 Zero propagation delay, zero ground bounce Undershoot clamp diodes on all switch and control inputs Available in QSOP and TSSOP packages APPLICATIONS: * * * * * * Hot-swapping, hot-docking Voltage translation (5V to 3.3V) Power Conservation Capacitance reduction and isloation Bus Isolation Clock Gating FUNCTIONAL BLOCK DIAGRAM A0 B0 A9 B9 BE The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE c 2013 Integrated Device Technology, Inc. JANUARY 2013 1 DSC-5767/6 IDTQS3861 HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT INDUSTRIAL TEMPERATURE RANGE ABSOLUTE MAXIMUM RATINGS(1) PIN CONFIGURATION Symbol Description VTERM(2) Max Unit VTERM(3) Supply Voltage to Ground -0.5 to +7 V DC Switch Voltage VS -0.5 to +7 V NC 1 24 Vcc A0 2 23 BE VTERM(3) DC Input Voltage VIN -0.5 to +7 V VAC AC Input Voltage (pulse width 20ns) -3 V mA A1 3 22 B0 4 21 IOUT DC Output Current 120 A2 B1 PMAX Maximum Power Dissipation 0.5 W TSTG Storage Temperature -65 to +150 C A3 5 20 B2 A4 6 19 B3 A5 7 18 B4 A6 8 17 B5 A7 9 16 B6 A8 10 15 B7 A9 11 14 B8 GND 12 13 B9 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VCC terminals. 3. All terminals except VCC . CAPACITANCE (TA = +25C, f = 1MHz, VIN = 0V, VOUT = 0V) Pins QSOP/ TSSOP TOP VIEW Typ. Max. (1) Unit Control Inputs 3 5 pF Quickswitch Channels (Switch OFF) 5 7 pF NOTE: 1. This parameter is guaranteed but not production tested. PIN DESCRIPTION Pin Names Description A0 - A9 Bus A B0 - B9 Bus B BE Bus Switch Enable FUNCTION TABLE(1) BE A0 - A9 Function H Z Disconnect L B0 - B9 Connect NOTE: 1. H = HIGH Voltage Level L = LOW Voltage Level Z = High-Impedance 2 IDTQS3861 HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Industrial: TA = -40C to +85C, VCC = 5V 5% Symbol Parameter Test Conditions Min. VIH Input HIGH Voltage Guaranteed Logic HIGH for Control Pins 2 VIL Input LOW Voltage Guaranteed Logic LOW for Control Pins IIN Input Leakage Current (Control Inputs) 0V VIN VCC Typ.(1) Max. Unit -- -- V -- -- 0.8 V -- 0.01 1 A I OZ Off-State Current (Hi-Z) 0V VOUT VCC, Switches OFF -- 0.01 1 A RON Switch ON Resistance VCC = Min., VIN = 0V, ION = 30mA -- 5 7 VCC = Min., VIN = 2.4V, ION = 15mA -- 10 15 VP Pass Voltage(2) VIN = VCC = 5V, IOUT = -5A 3.7 4 4.2 NOTES: 1. Typical values are at VCC = 5V and TA = 25C. 2. Pass voltage is guaranteed but not production tested. TYPICAL ON RESISTANCE vs VIN AT VCC = 5V 16 14 R ON (ohms) 12 10 8 6 4 2 0 0.0 0.5 1.0 1.5 2.0 V IN (Volts) 3 2.5 3.0 3.5 V IDTQS3861 HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT INDUSTRIAL TEMPERATURE RANGE POWER SUPPLY CHARACTERISTICS Symbol Parameter Test Conditions(1) Typ.(2) Max. Unit ICCQ Quiescent Power Supply Current VCC = Max., VIN = GND or VCC, f = 0 0.2 3 A ICC Power Supply Current per Input HIGH(3) VCC = Max., VIN = 3.4V, f = 0 2.5 mA ICCD Dynamic Power Supply Current per MHz(4) VCC = Max., A and B Pins Open, 0.25 mA/MHz BE Input Toggling @ 50% Duty Cycle NOTES: 1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics. 2. Typical values are at VCC = 5V and TA = 25C. 3. Per TTL-driven input (VIN = 3.4V, control inputs only). A and B pins do not contribute to Icc. 3. This current applies to the control inputs only and represents the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant AC or DC currents as they transition. This parameter is guaranteed but not production tested. SWITCHING CHARACTERISTICS OVER OPERATING RANGE TA = -40C to +85C, VCC = 5V 5% CLOAD = 50pF, RLOAD = 500 unless otherwise noted. Symbol Min. (1) Parameter Typ. Max. Unit 0.25(3) ns tPLH tPHL Data Propagation Delay(2) tPZL tPZH Switch Turn-On Delay BE to A or B 1.5 6.5 ns tPLZ tPHZ Switch Turn-Off Delay(2) BE to A or B 1.5 5.5 ns A to B, B to A NOTES: 1. Minimums are guaranteed but not production tested. 2. This parameter is guaranteed but not production tested. 3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone is of the order of 0.25ns at CL = 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on the driven side. 4 IDTQS3861 HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION QS XXXXX Device Type XX Package X Blank 8 Tube or Tray Tape and Reel QG PAG Quarter Size Outline Package - QSOP Green Thin Shrink Small Outline Package - TSSOP Green 3861 High Speed CMOS 10-Bit Bus Switch with Flow-Through Pinout Datasheet Document History 01/25/13 Pg. 1, 5 Updated the Ordering Information by removing non green package version, the "IDT" notation and Adding Tape and Reel information. CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com 5 for Tech Support: logichelp@idt.com