Embest Mini8510 Processor Card Top-View Bottom-View Features Mechanical Parameters z Dimensions: 67 x 37 mm z Working temperature: 0~70 Celsius z Humidity Range: 20% ~ 90% z Power Consumption: 1A @ 3.3V Processor z TI DM3730 DaVinci Digital Media Processor (pin-to-pin compatible with TI AM3715) - Up to 1-GHz ARM(R) CortexTM-A8 Core, also supports 300, 600, and 800-MHz operation - Up to 800-MHz TMS320C64x+TM DSP Core, also supports 260, 520 and 660-MHz operation (DM3730 only) - NEONTM SIMD Coprocessor - POWERVR SGXTM Graphics Accelerator - ARM: 32KB I-Cache; 32KB D-Cache; 256KB L2 Cache - Onchip 32KB ROM and 64KB Shared SDRAM Memory z 256MB DDR SDRAM, 32-bit z 512MB NAND Flash, 16-bit Onboard Headers and Signals Routed to Pins z 12-bit Camera interface (30-pin FPC connector, support CCD or CMOS camera) z 1-channal 4-wire JTAG interface (10-pin 1.0mm pitch connector) z 6 LEDs (programmable status LEDs) z 2-channel SPI z GPMC bus (16-bit data bus, 10-bit address bus, 4 chip-selection signals and several control signals) z 3-channel 5-wire UARTs z 1-channel ULPI (USB1 HS) z Audio in/out 1 z z z z 1-channel I2C 2-channel McBSP (McBSP1 and McBSP3, McBSP3 is multiplex with UART2) 2-channel SD/MMC: MMC1 (8-wire), MMC2 (4-wire) 24-bit DSS interface General Description Embest Mini8510 processor card is based on TI's DM3730 DaVinci Digital Media processor which is powered by 1GHz ARM Cortex-A8 and 800MHz C64x+ DSP core. The Mini8510 hardware is compatible with Embest Mini8100 OMAP3530 processor card which is convenient for customers who used Mini8100 before to upgrade to Mini8510 so as to migrate from the OMAP3530 to DM3730 for their embedded designs. The SBC8100 expansion board for integration of the Embest Mini8100 processor card can be also used for Mini8510. The processor card is connected with SBC8100 expansion board through two 1.27mm space 2*45-pin dip connectors. We call the upgraded DM3730 system SBC8100 Plus. Embest offers Linux 2.6.32 and WinCE6.0 BSP for this board. Customers can leverage our experience to increase your own productivity. The optimal embedded microprocessor solution provides users with a flexible development environment based on DM3730 and a shortened development timeframe. Layout and Functional Block Diagram MCP Memory Nand Flash JTAG TV GPIO UART DM3730 / AM3715 1GHz ARM Cortex-A8 800MHz TMS320C64x (DM3730 only) GPMC NEON, SGX Graphics Accelerator 512MB 16bit Audio in I2C Audio out SDRC DDR SDRAM OTG DSS 256MB 32bit TPS65930 Power Management USB Interface CCD/CMOS Interface MMC Keyboard CONNECTOR to MAINBOARD 2 Dimensions Mini8510 Top View 3 Mini8510 Top-View Perspective Drawing 4 Camera interface Embest Mini8510 processor card uses a 30-pin FPC connector, supporting CCD or CMOS camera. Detailed pin explanation is as following: Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Signal GND D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 GND PCLK GND HS VDD50 VS VDD33 XCLKA XCLKB GND FLD WEN STROBE SDA SCL GND VDD18 Description GND Digital image data bit 0 Digital image data bit 1 Digital image data bit 2 Digital image data bit 3 Digital image data bit 4 Digital image data bit 5 Digital image data bit 6 Digital image data bit 7 Digital image data bit 8 Digital image data bit 9 Digital image data bit 10 Digital image data bit 11 GND Pixel clock GND Horizontal synchronization 5V Vertical synchronization 3.3V Clock output a Clock output b GND Field identification Write Enable Flash strobe control signal IIC master serial clock IIC serial bidirectional data GND 1.8V 5 JTAG interface Embest Mini8510 processor card has a 10-pin 1.0mm pitch JTAG connector on board. Detailed pin explanation is as following: Pin 1 2 3 4 5 6 7 8 9 10 Signal VDD18 TMS TD1 NTRST TD0 RTCK TCK EMU0 EMU1 GND Description 1.8V output Test mode select Test data input Test system reset Test data output Receive test clock Test clock Test emulation 0 Test Emulation 1 GND Two 2*45-pin Expansion Connectors Embest Mini8510 processor card is connected to carrierboard via two 1.27mm space 2*45-pin dip connectors. Detailed pin explanation for CON1 is as following: Pin 1 2 Signal G_NWE G_NOE 3 G_NCS7GPT8G_DIR 4 G_NCS4GPT9DMAREQ1 5 G_NCS6GPT11DMAREQ3 6 7 8 9 10 11 12 13 14 15 16 17 18 19 G_NCS3DMAREQ0 GND G_WAIT0 G_NBE0 / G_CLE G_NATV_ALE G_NBE1 HDQ_SIO MMC1_D0 MMC1_D1 MMC1_D2 MMC1_D6/IO128 MMC1_D5/IO127 MMC1_D4/IO126 MMC1_D7/IO129 Description GPMC Write Enable GPMC Read Enable GPMC Chip Select bit 7PWM or event for GP timer 8GPMC IO direction control for use with external transceivers GPMC Chip Select bit 7PWM or event for GP timer 9External DMA request 1 GPMC Chip Select bit 7PWM or event for GP timer 11 External DMA request 3 GPMC Chip Select bit 7External DMA request 0 GND External indication of wait Lower Byte Enable. Also used for Command Latch Enable Address Valid or Address Latch Enable Upper Byte Enable Bidirectional HDQ 1-Wire control and data MMC/SD Card Data bit 0 MMC/SD Card Data bit 1 MMC/SD Card Data bit 2 MMC/SD Card Data bit 6 MMC/SD Card Data bit 5 MMC/SD Card Data bit 4 MMC/SD Card Data bit 7 6 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 MMC1_D3 GND MMC1_CLK MMC1_CMD VMMC1 UART3_RX_IRRX UART3_CTS_RCTX UART3_TX_IRTX UART3_RTS_SD DSS_ACBIAS DSS_VSYNC GND DSS_HSYNC DSS_CLK DSS_D6 DSS_D8 DSS_D7 DSS_D9 DSS_D20 DSS_D17 DSS_D16 DSS_D18 DSS_D10 DSS_D5 DSS_D4 GND DSS_D2 DSS_D3 DSS_D0 DSS_D15 DSS_D11 DSS_D23 DSS_D22 DSS_D14 DSS_D19 DSS_D13 DSS_D21 DSS_D1 DSS_D12 GND MCBSP1_FSR/IO157 MCBSP1_CLKR/IO156 MCBSP1_FSX/IO161 MCBSP1_CLKS/IO160 MCBSP1_CLKX/IO162 MCBSP1_DR/IO159 MCBSP1_DX/IO158 GND MMC/SD Card Data bit 3 GND MMC/SD Output Clock MMC/SD command signal Power supply for SD/MMC1 (3.0 / 1.8V) UART3 Receive data, IR and Remote RX UART3 Clear To Send, Remote TX UART3 Transmit data, IR TX UART3 Request To Send, IR enable AC bias control (STN) or pixel data enable (TFT) output LCD Vertical Synchronization GND LCD Horizontal Synchronization LCD Pixel Clock LCD Pixel Data bit 6 LCD Pixel Data bit 8 LCD Pixel Data bit 7 LCD Pixel Data bit 9 LCD Pixel Data bit 20 LCD Pixel Data bit 17 LCD Pixel Data bit 16 LCD Pixel Data bit 18 LCD Pixel Data bit 10 LCD Pixel Data bit 5 LCD Pixel Data bit 4 GND LCD Pixel Data bit 2 LCD Pixel Data bit 3 LCD Pixel Data bit 0 LCD Pixel Data bit 15 LCD Pixel Data bit 11 LCD Pixel Data bit 23 LCD Pixel Data bit 22 LCD Pixel Data bit 14 LCD Pixel Data bit 19 LCD Pixel Data bit 13 LCD Pixel Data bit 21 LCD Pixel Data bit 1 LCD Pixel Data bit 12 GND Receive frame synchronization Receive Clock Transmit frame synchronization External clock input Transmit clock Received serial data Transmitted serial data GND 7 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 TV_OUTC TV_OUTY VDD33 IIC3_SCL IIC3_SDA IO25 IO27 BOOTJUMP GND VBUS USB_DN USB_ID USB_DP PWM0 KR0 KR1 KR2 KR3 KR4 VDD18 GND VDD18 BKBAT TV analog output S-VIDEO: TV_OUT2 TV analog output Composite: TV_OUT1 Power supply for camera (3.3V 500mA ) I2C Master Serial clock. Output is open drain I2C Serial Bidirectional Data. Output is open drain General-purpose IO 183 General-purpose IO 183 Boot configuration mode bit 5. GND VBUS power rail (5V 10mA) USB Data N USB ID USB Data P Pulse width driver 0 Keypad row 0 Keypad row 1 Keypad row 2 Keypad row 3 Keypad row 4 Power supply from TPS65930 (VIO 1.8V) GND Power supply from TPS65930 (VIO 1.8V) Backup battery Detailed pin explanation for CON2 is as following: Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Signal GND G_D14 G_D13 G_D10 G_D8 G_D9 G_D5 G_D7 G_D3 G_D6 G_D12 G_D2 G_D11 G_D1 G_D4 G_D0 G_A2 G_A3 G_A1 G_A6 G_A4 Description GND GPMC data bit 14 GPMC data bit 13 GPMC data bit 10 GPMC data bit 8 GPMC data bit 9 GPMC data bit 5 GPMC data bit 7 GPMC data bit 3 GPMC data bit 6 GPMC data bit 12 GPMC data bit 2 GPMC data bit 11 GPMC data bit 1 GPMC data bit 4 GPMC data bit 0 GPMC address bit 2 GPMC address bit 3 GPMC address bit 1 GPMC address bit 6 GPMC address bit 4 8 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 G_A7 G_A5 G_A8 G_A9 G_D15 G_A10 GND SPI2_CS1 GPT8 SPI2_CS10 GPT11 SPI2_SIMO GPT9 SPI2_CLK SPI2_SOMI GPT10 SPI1_CS3 SPI1_CS0 SPI1_SIMO SPI1_SOMI SPI1_CLK GND GPIO0 MMC2_D2 SPI3_CS1 MMC2_D3SPI3_CS0 MMC2_D0SPI3_SOMI MMC2_D1 MMC2_CMDSPI3_SIMO MMC2_CLKSPI3_CLK BSP3_DRUART2_RTS BSP3_CLKUART2_TX BSP3_FSXUART2_RX BSP3_DXUART2_CTS GND UART1_CTS UART1_TX UART1_RX UART1_RTS USB1HS_STP USB1HS_D3 USB1HS_D5 USB1HS_6 USB1HS_D7 USB1HS_D1 USB1HS_D2 USB1HS_D4 USB1HS_D0 USB1HS_NXT USB1HS_CLK GND USB1HS_DIR SYS_CLKOUT1 GPMC address bit 7 GPMC address bit 5 GPMC address bit 8 GPMC address bit 9 GPMC data bit 15 GPMC address bit 10 GND SPI Enable 1PWM or event for GP timer 8 SPI Enable 0PWM or event for GP timer 11 Slave data in, master data out PWM or event for GP timer 9 SPI Clock Slave data out, master data inPWM or event for GP timer 10 SPI Enable 3 SPI Enable 0 Slave data in, master data out Slave data out, master data in SPI Clock GND GPIO0 /card detection 1 MMC/SD Card Data bit 2SPI Enable 1 MMC/SD Card Data bit 3SPI Enable 0 MMC/SD Card Data bit 0Slave data out, master data in MMC/SD Card Data bit 1 MMC/SD command signalSlave data in, master data out MMC/SD Output ClockSPI Clock Received serial dataUART2 Request To Send Combined serial clockUART2 Transmit data Combined frame synchronizationUART2 Receive data Transmitted serial dataUART2 Clear To Send GND UART1 Clear To Send UART1 Transmit data UART1 Receive data UART1 Request To Send Dedicated for external transceiver Stop signal Dedicated for external transceiver Bidirectional data bus Dedicated for external transceiver Bidirectional data bus Dedicated for external transceiver Bidirectional data bus Dedicated for external transceiver Bidirectional data bus Dedicated for external transceiver Bidirectional data bus Dedicated for external transceiver Bidirectional data bus Dedicated for external transceiver Bidirectional data bus Dedicated for external transceiver Bidirectional data bus Dedicated for external transceiver Next signal from PHY Dedicated for external transceiver 60-MHz clock GND Dedicated for external transceiver data form PHY Configurable output clock1 9 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 LEDA LEDB ADCIN0 NRESPWRON NRESWARM SYSEN GND REGEN ADCIN1 KC0 KC1 KC2 KC3 AUDIO_IN AUDIO_OR AUXR AUDIO_OL GND VBAT ON/OFF VBAT LED leg A LED leg B ADC input0 (Battery type) Power On Reset Warm Boot Reset (open drain output) System enable output GND Enable signal for external LDO ADC input1 (General-purpose ADC input) Keypad column 0 Keypad column 0 Keypad column 0 Keypad column 0 Analog microphone bias 1 Predriver output right P for external class-D amplifier Auxiliary audio input right Predriver output left P for external class-D amplifier GND Power supply (3V - 4.2V 1.5A) Input; detect a control command to start or stop the systerm Power supply (3V - 4.2V 1.5A) Order Information Order No. Item Options Price T400304 Embest Mini8510 Processor Card Embest SBC8100 Plus Single Board Computer Please contact Embest Embest Info&Tech Co., LTD. Room 509, Luohu Science&Technology Building, #85 Taining Rd., Shenzhen, Guangdong, China 518020 Tel: +86-755-25635656/25636285 Fax: +86-755-25616057 Email: market@embedinfo.com http://www.embedinfo.com/english http://www.armkits.com 10