Parameter Symbol 500KHz ~ 125.0MHz
Frequency Stability Δf/fo ±25ppm, ±50ppm and ±100ppm
Temp Operating Range Topr 0 ~ +70°, -10 ~ +70°C
Temp Storage Range Tstg -40~85°C
Supply Voltage VDD 3.3Vdc ±10% 5.0Vdc ±10%
15mA max 25mA max
25mA max 35mA max
40/60%, 45/55% TTL
40/60%, 45/55% HCMOS
Output Level ‘0’ VOL TTL 0.4V max, HCMOS .33V max
TTL 0.4V max, HCMOS 0.5V max
Output Level ‘1’ VOH TTL 2.4V min, HCMOS 2.97V min VDD
TTL 2.4V min, HCMOS 4.5V min VDD
Output Logic TTL / HCMOS
TTL 10 Gates
CMOS 15 pF
Measured between 0.4V ~ 2.4V (RL = 390
Ω
; CL = 15pF)
Measured between 10%~ 90% VDD (CL = 15pF)
Start-up Time 4mSec max,
Option on Pin 1 Tri State or No Connection
Aging ±5ppm / year max
ACT1100
(
'V'
SERIES
)
A
CT1700 ( 'CL' SERIES )
Issue 5 C1A
Date 23/3/6
Please Specify
Frequency Range fo
Please Specify
VDD = 3.3V
VDD = 5.0V
VDD = 3.3V
VDD = 5.0V
Please note that all parameters can not necessarily be specified in the same device
Supply Current Iop
Please Specify
Please Specify
0.5 - 27MHz
Fax : 0044 (0)118 979 1283
Customer to specify : Frequency, Operating Temperature Range, Frequency Stability, Supply Voltage, Duty Cycle, Output Enable (Tristate) If required
In line with our ongoing policy of product evolvement and improvement, the above specification may be subject to change without notice
ISO9001:2000 Registered
http:
//
www.actcrystals.com
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berkshire, RG41 2EY, UK
Tel : 0044 (0)118 979 1238
email : info@actcrystals.com
Condition
ACT1100 / ACT1700 Standard Clock Oscillators
The ACT1100 is a full size through hole oscillator. The ACT1700 is a half size through hole oscillator. The
popularity of these families still remains even after the advent of smaller surface mount devices. With wide
frequency and operating temperature ranges, these series offer low cost & good reliability for ATM, Networking,
Microprocessor and Consumer applications. An option with a supply voltage of 2.5V is available please contact
our sales desk for details. For frequencies < 500KHz, >125MHz & ± 10ppm stability please refer to the
ACT1100HS/1700HS data.
Specificatio
n
Specification
CMOS 10nSec max, 3nSec typical
@25°C
Duty Cycle TW/t
Rise & Fall Time tr/tf
Output Load
TTL 10nSec max, 3nSec typical
Please Specify
Measured at 50% VDD
Measured at +1.4Volts
27 - 125MHz
Plating Material on leads
SnAgCu
Soldering conditions
please refer to page 3
1 of 3
Reliability tests
Issue 5 C1A
Date 23/3/6
ACT1100 / ACT1700 Standard Clock Oscillators
105±3°C 16 hrs measurements after at least 1 hr at atmospheric conditions
Aging 85±3°C 30 days measurements after at least 1 hr at atmospheric conditions.
As per profile fig.1 below and/or soldering iron applied for 5s max tip
temperature 350±10°C
Low Temperature
Storage -55±3°C 2hrs measurements after at least 1 hr at atmospheric conditions
High Temperature
Storage
Specification as
per page 1 must be
met.
Damp Heat
Constant Temperature 40±2°C RH 90~95% for 56 days. Measurements after at 1 hr at
atmospheric conditions
Resistance to
Soldering Heat
http://www.actcrystals.com
Fax : 0044 (0)118 979 1283
Test Test Method
Drop 750mm height.
3 drops.
Onto wood.
Shock
In line with our ongoing policy of product evolvement and improvement, the above specification may be subject to change without notice
ISO9001:2000 Registered
For quotations or further information please contact us at:
3 The Business Centre, Molly Millars Lane, Wokingham, Berkshire, RG41 2EY, UK
Thermal Cycling
100cycles to the temperature profile fig 2 below. Measurements after at least 1
hr at atmospheric conditions
Solderability 255±5°C for 10±0.5s using Rosin resin methyl alcohol flux Solvent (1:4) dipped
to a nominal depth of 0.5mm.
Vibration 10 to 55Hz and return to 10Hzamplitude 1.5mm sweep time 1min.
2 hrs each of X, Y and Z axis.
Total test time 6 hrs
Leak Helium bomb: Pressure 200kpa Time 70 min
pressure release 5 min measure within 30min
Measurement
Requirements
<4x10-9pa.m3/s
Tel : 0044 (0)118 979 1238
Peak acceleration 981m/s2 Pulse duration 6ms
Each of X, Y and Z axis.
3 shocks each axis
email : info@actcrystals.com
2 of 3
ACT1100 / ACT1700 Standard Clock Oscillator
s
Application circuits
Date 23/3/6
3 The Business Centre, Molly Millars Lane, Wokingham, Berkshire, RG41 2EY, UK
http://www.actcrystals.com
In line with our ongoing policy of product evolvement and improvement, the above specification may be subject to change without notice
ISO9001:2000 Registered
Issue 5 C1A
For quotations or further information please contact us at:
Tel : 0044 (0)118 979 1238
Fax : 0044 (0)118 979 1283
email : info@actcrystals.com
3 of 3
