SC60-20 - Teledyne Technologies Incorporated

Optically Isolated 0.5 to 2.5A

Bi-Directional Solid-State Relay

Series C60

Part Number Relay Description

C60-X0 Solid-State Relay, Terminals for Through Hole Mount

SC60-X0 Solid-State Relay, Terminals for Surface Mount

ELECTRICAL SPECIFICATIONS

(25°C UNLESS OTHERWISE SPECIFIED)

INPUT (CONTROL) SPECIFICATIONS (See Note 1)

Parameter Min Max Units

Input Voltage Drop (See Figure 1) 1.1 1.5 Vdc

Input Current (See Figure 1 and Notes 1, 7) 50 mA

Input Current (Guaranteed On), (See Figure 4 and Note 7) 10 mA

Input Current (Guaranteed Off) 100 µA

Reverse Voltage Protection -6 Vdc

OUTPUT (LOAD) SPECIFICATIONS (See Figure 2 And Note 2)

Part Number DC Bi-Directional

Parameter Min Max Min Max Units

Output Voltage Rating C60-10 60 ±60 Vdc

C60-20 100 ±100 Vdc

C60-30 200 ±200 Vdc

C60-40 400 ±400 Vdc

Output Current Rating C60-10 2.5 ±1.25 Adc

C60-20 1.5 ±0.75 Adc

C60-30 1.0 ±0.50 Adc

C60-40 0.5 ±0.25 Adc

On Resistance C60-10 0.07 0.28 Ohm

(See Note 6) C60-20 0.2 0.7 Ohm

C60-30 0.45 1.8 Ohm

C60-40 1.0 4.0 Ohm

Leakage Current at Rated Voltage 2.0 1.0 µAdc

Turn-On Time @ 10mA C60-10 4.0 4.0 ms

(See Figure 4 and Note 7) C60-20,-30,-40 3.0 3.0 ms

Turn-Off Time C60-10 4.0 4.0 ms

C60-20,-30,-40 3.0 3.0 ms

Output Capacitance C60-10 1000 500 pf

C60-20 500 250 pf

C60-30 400 200 pf

C60-40 400 200 pf

Isolation (Input to Output) 109109Ohms

Dielectric Strength 1500 1500 Vrms

Capacitance (Input to Output) 3.0 3.0 pF

Junction Temperature (TJ)125 125 °C

Junction to Case Thermal Resistance 25 °C

Case to Ambient Thermal Resistance 75 °C/W

BLOCK DIAGRAM

FEATURES/BENEFITS

•Power FET Output with Very

Low On Resistance: Virtually no

offset with very low leakage and

voltage drop.

•Optical Isolation: Isolates

control elements from load

transients. Eliminates ground

loops and signal ground noise.

•Three Terminal Output: Output

FETs can be paralleled

externally to change current

load rating.

• Floating Output: Allows for high

and low side switching.

•Switches High Voltages and

Currents: Voltages to 400 Vdc.

Current to 2.5 Adc.

Bi-directional, DC or AC.

•High Noise Immunity: Control

circuit cannot be triggered by

output switching noise.

•6-Pin Mini-DIP Package:

Standard or surface mount

available.

DESCRIPTION

The Series C60 solid-state relay is

an advanced design capable of

switching very heavy loads in a

physically small 6-pin mini DIP

package. These relays have a

power FET output that ensures low

On resistance, no offset voltage

and low leakage current. They are

versatile and can be used to switch

AC, Bi-directional or DC loads.

Optical isolation ensures complete

protection of signal lines, power

and ground bus and control circuits

from switching noise and EMI.

Add suffix 01 to denote 60Sn/40Pb Pre-Tinned Leads

2DSC60-X0 Rev --

Series C60

CHARACTERISTIC CURVES

WIRING CONFIGURATIONS

MECHANICAL SPECIFICATION

NOTES:

1. Series resistor is required to limit input current to

50 mA maximum.

2. The input current is 10 mA for all tests unless

otherwise specified.

3. The surge current is non-repetitive for a

maximum duration of 20 ms (See Figure 3).

4. Loads may be connected to positive or negative

referenced power supplies. Inductive loads must

be diode suppressed.

5. Continuous load current is rated under the

conditions of still air and mounted on a printed

circuit board.

6. To calculate ON Resistance for a given junction

temperature calculate the new ROn using the

equation shown below:

ROn=R(25°C)x e0.006(TJ-25°C)

7. Turn on Time can be controlled with input control

current. Calculate a new turn-on time:

tOn=(tSpecification Limit)(10mA/IIn)

8. Load voltage rating should be derated 10% at

-40°C

• Operating Temperature Range: -40°C to 85°C

• Storage Temperature Range: -40°C to 100°C

• Weight: 1 gm. maximum

• Case: 6 pin dual in line, filled epoxy

2DSC60-X0 Rev --