11-21VGC/TR8 - EVERLIGHT ELECTRONICS

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 1 of 9

Device No:DSE-111-082 Prepared date: 13-Feb-2006 Prepared by: Ashley Kuo

Technical Data Sheet

1206 Package Chip LEDs with Inner Lens

11-21VGC/TR8

Features

․Package in 8mm tape on 7〞diameter reel.

․Compatible with automatic placement equipment.

․Compatible with infrared and vapor phase reflow

solder process.

․Mono-color type.

․Pb-free.

․The product itself will remain within RoHS

compliant version.

Descriptions

․The 11-21 SMD Taping is much smaller

than lead frame type components, thus

enable smaller board size, higher packing

density, reduced storage space and finally

smaller equipment to be obtained.

․Besides, lightweight makes them ideal for

miniature applications. etc.

Applications

․Backlighting in dashboard and switch.

․Telecommunication: indicator and backlighting in

telephone and fax.

․Flat backlight for LCD, switch and symbol.

․General use.

Device Selection Guide

Chip

Material Emitted Color

Lens Color

GaP Yellow Green Water Clear

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 2 of 9

Device No:DSE-111-082 Prepared date: 13-Feb-2006 Prepared by: Ashley Kuo

11-21VGC/TR8

Package Outline Dimensions

-+

Note: The tolerances unless mentioned is ±0.1mm,Unit = mm

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 3 of 9

Device No:DSE-111-082 Prepared date: 13-Feb-2006 Prepared by: Ashley Kuo

11-21VGC/TR8

Absolute Maximum Ratings (Ta=25℃)

Parameter Symbol Rating Unit

Reverse Voltage VR 5 V

Forward Current IF 30 mA

Operating Temperature Topr -40 ~ +85 ℃

Storage Temperature Tstg -40~ +90 ℃

Electrostatic Discharge (HBM) ESD 2000 V

Power Dissipation Pd 100 mW

Peak Forward Current

(Duty 1/10 @1KHz) IFP 60 mA

Soldering Temperature Tsol Reflow Soldering : 260 ℃ for 10 sec.

Hand Soldering : 350 ℃ for 3 sec.

Electro-Optical Characteristics (Ta=25℃)

Parameter Symbol Min. Typ. Max. Unit Condition

Luminous Intensity Iv 11 18 ----- mcd IF=20mA

Viewing Angle 2θ1/2 ----- 60 ----- deg IF=20mA

Peak Wavelength λp ----- 570 ----- nm IF=20m A

Dominant Wavelength λd ----- 571 ----- nm IF=20mA

Spectrum Radiation

Bandwidth △λ ----- 30 ----- nm IF=20mA

Forward Voltage VF 1.7 2.0 2.4

V IF=20mA

Reverse Current IR ----- ----- 10

μA VR=5V

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 4 of 9

Device No:DSE-111-082 Prepared date: 13-Feb-2006 Prepared by: Ashley Kuo

11-21VGC/TR8

Typical Electro-Optical Characteristics Curves

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 5 of 9

Device No:DSE-111-082 Prepared date: 13-Feb-2006 Prepared by: Ashley Kuo

11-21VGC/TR8

Label explanation

CAT: Luminous Intensity Rank

HUE: Dom. Wavelength Rank

REF: Forward Voltage Rank

Reel Dimensions

Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 6 of 9

Device No:DSE-111-082 Prepared date: 13-Feb-2006 Prepared by: Ashley Kuo

11-21VGC/TR8

Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel

Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm

Moisture Resistant Packaging

Label Desiccant Label

Aluminum moisture-proof bag

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 7 of 9

Device No:DSE-111-082 Prepared date: 13-Feb-2006 Prepared by: Ashley Kuo

11-21VGC/TR8

Reliability Test Items And Conditions

The reliability of products shall be satisfied with items listed below.

Confidence level：90%

LTPD：10%

No. Items Test Condition

Test

Hours/Cycles Sample

Size Ac/Re

1 Reflow Soldering

Temp. : 260℃±5℃

Min. 5sec. 6 Min. 22 PCS. 0/1

2 Temperature Cycle

H : +100℃ 15min

∫ 5 min

L : -40℃ 15min

300 Cycles 22 PCS. 0/1

3 Thermal Shock

H : +100℃ 5min

∫ 10 sec

L : -10℃ 5min

300 Cycles 22 PCS. 0/1

4 High Temperature

Storage Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1

5 Low Temperature

Storage Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1

6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1

7 High Temperature /

High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 8 of 9

Device No:DSE-111-082 Prepared date: 13-Feb-2006 Prepared by: Ashley Kuo

11-21VGC/TR8

Precautions For Use

1. Over-current-proof

Customer must apply resistors for protection, otherwise slight voltage shift will cause big

current change ( Burn out will happen ).

2. Storage

2.1 Do not open moisture proof bag before the products are ready to use.

2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less.

2.3 After opening the package: The LED's floor life is 1 year under 30 deg C or less and 60% RH or less.

If unused LEDs remain, it should be stored in moisture proof packages.

2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the

storage time, baking treatment should be performed using the following conditions.

Baking treatment : 60±5℃ for 24 hours.

3. Soldering Condition

3.1 Pb-free solder temperature profile

3.2 Reflow soldering should not be done more than two times.

3.3 When soldering, do not put stress on the LEDs during heating.

3.4 After soldering, do not warp the circuit board.

EVERLIGHT ELECTRONICS CO.,LTD.

Everlight Electronics Co., Ltd. http://www.everlight.com Rev 1 Page: 9 of 9

Device No:DSE-111-082 Prepared date: 13-Feb-2006 Prepared by: Ashley Kuo

11-21VGC/TR8

4.Soldering Iron

Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds

within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and

do soldering of each terminal. Be careful because the damage of the product is often started at the time

of the hand solder.

5.Repairing

Repair should not be done after the LEDs have been soldered. When repairing is unavoidable,

a double-head soldering iron should be used (as below figure). It should be confirmed beforehand

whether the characteristics of the LEDs will or will not be damaged by repairing.

EVERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936

Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306

Tucheng, Taipei 236, Taiwan, R.O.C http://www.everlight.com