Type 715P Vishay Sprague Polypropylene Film Capacitors ORANGE DROP(R), Low Loss Polyproplyene plastic film is employed as the dielectric in Type 715P ORANGE DROP(R) capacitors. Type 715P capacitors are ideal for applications where high AC current flow is found, as in certain solid-state TV vertical circuits, r-f generators and pulse-forming networks where dielectric heating is often a problem. RoHS COMPLIANT The polyproplyene dielectric film is similar to polystyrene in that it can handle high AC currents due to is low loss but with the added advantage of an operating temperature to + 105 C. Capacitance change with temperature is less than 3 % over the entire operating temperature range. The temperature coefficient is negative and virtually linear at 180 PPM/C over the temperature range of + 25 C to + 105 C. This characteristic means the Type 715P is suitable for matching with positive TC resistors and inductors to maintain circuit stability. Type 715P ORANGE DROP(R) capacitors are conformally coated with a flame retardant epoxy. Performance characteristics, as well as curves showing typical variation in electrical characteristics as a function of temperature and frequency, are given. PERFORMANCE CHARACTERISTICS Operating Temperature: - 55 C to + 85 C, standard; up to + 105 C when working voltage is reduced to 50 % of the + 85 C rating. Insulation Resistance: After a 2 minute charge at rated voltage or 500 V, whichever is less. At + 25 C: 400 000 Megohm for C 0.5 F 200 000 Megohm - Microfarads for C > 0.5 Microfarads At + 85 C: 20 000 Megohm for C 0.5 Microfarads 10 000 Megohm - Microfarads for C > 0.5 Microfarads At + 105 C: 2000 Megohm for C 0.5 F 1000 Megohm - Microfarads for C > 0.5 Microfarads Capacitance Tolerance and Dissipation Factor: Capacitors shall be measured at a frequency of 1000 Hz at + 25 C or else be referred to measurements made at that frequency and temperature. The maximum dissipation factor shall be 0.1 %. Dielectric Withstanding Voltage: Capacitors rated below 1000 volts shall withstand a DC potential of 250 % of rated voltage applied between terminals for not more than 5 seconds. Capacitance rated 1000 volts and above shall withstand a DC potential of 200 % of rated voltage applied between the terminals for not more than 5 seconds. The test voltage must be applied and discharged through a resistor of 1 ohm per volt. Humidity Test: Condition capacitors with no voltage applied for 72 hours at 95 % relative humidity and + 75 C. Remove capacitors from humidity chamber, wipe surface dry of moisture and dry in circulating air for 4 hours. Measure insulation resistance after a two minute charge at + 25 C and rated voltage or 500 VDC, whichever is less. Minimum product of insulation resistance and capacitance shall be 50 000 Megohm - microfarads after test but need not exceed 100 000 Megohm. Not more than one failure in 12 units tested shall be permitted. DC Life Test: Capacitors are capable of withstanding a 500 hour life test at + 85 C at 150 % of rated working voltage. After test, capacitance shall not have changed by more than 5 % of initial value, insulation resistance shall not have decreased by more than 50 % of the initial limit and dissipation factor shall not have increased to more than 0.1 %. AC Life Test: Capacitors shall withstand the maximum 60 Hz voltage for a period of 500 hours at + 85 C. Rated DC Voltage 200 400, 600 800, 1200, 1600 Maximum 60 Hz Voltage 155 200 500 Not more than one failure allowed in 12 units tested. Document Number: 42018 Revision: 13-Feb-07 For technical questions, contact: spresale@vishay.com www.vishay.com 25 Type 715P Polypropylene Film Capacitors ORANGE DROP(R), Low Loss Vishay Sprague DIMENSIONS in inches (millimeters) L Max. L Max. L Max. 0.250 [6.350] Max. 1.250 [31.750] Min. D Max. 0.250 [6.350] Max. 0.250 [6.350] Max. Lead Length Lead Length 0.032 [0.813] Dia. (No. 20 AWG) Tinned Copper-Clad Steel S S Terminal A S Terminal B CASE CODE L (Max.) J Terminal D S Terminal A 0.060 [1.524] Terminal B 0.030 [ 0.762] Terminal D 0.030 [0.762] 0.75 [19.050] 0.500 [12.700] 0.500 [12.700] 0.375 [9.525] K 0.95 [24.130] 0.688 [17.475] 0.688 [17.475] 0.375 [9.525] L 1.30 [33.020] 1.031 [26.187] 0.969 [24.613] 0.719 [18.263] M 1.70 [43.180] 1.406 [35.712] 1.344 [34.138] 1.094 [27.788] +2 10-2 +1 0 5 TYPICAL -1 -2 - 55 - 50 2 - 25 0 + 25 + 50 + 85 + 105 + 125 + 75 + 100 TEMPERATURE DEG. CENTIGRADE T AN ? PERCENT DISSIPATION FACTOR - 1000 Hz PERCENT CAPACITANCE CHANGE - 1000 H z PERFORMANCE CHARACTERISTICS 10-3 5 0.075 TYPICAL 0.05 2 0.025 TYPICAL 10-4 0 - 55 - 50 1 - 25 0 + 25 + 50 2 + 85 + 105 + 125 + 75 + 100 5 10 2 5 100 2 5 1000 TEMPERATURE DEG. CENTIGRADE 1000 5 5 12 .0 82 5 .4 7 F .0 03 9 F .0 .1 8 F F 18 F 400 V 2 F 7 200 V .4 7 F 5 39 .2 2 F F .0 100 F 100 200 39 .0 VOLTS - rms 2 155 .0 VOLTS - rms TEMPERATURE DEG. CENTIGRADE 1000 10 10 1 2 5 10 2 5 100 2 5 1000 1 2 5 FREQUENCY - kHz www.vishay.com 26 For technical questions, contact: spresale@vishay.com 10 2 5 100 2 5 1000 FREQUENCY - kHz Document Number: 42018 Revision: 13-Feb-07 Type 715P Polypropylene Film Capacitors ORANGE DROP(R), Low Loss Vishay Sprague 1000 1000 5 450 0. 05 0. 200 1 VOLTS - rms 00 F VOLTS - rms PERFORMANCE CHARACTERISTICS 0. 100 02 7 0. 22 0. 00 F 82 F 5 F 0. 1 5 F 0. 00 56 F F F F 2 600 V 10 800 V 10 1 2 5 10 2 5 100 2 5 1000 1 2 5 10 FREQUENCY - kHz 2 5 100 2 5 1000 FREQUENCY - kHz 1000 1000 0. 475 2 7 0. F 27 00 82 0. F 04 100 7 F 03 F 2 0. 00 39 0. 01 5 5 F F 3 18 0. 01 F F F 0. 00 56 100 0. 01 8 5 2 2 00 0. VOLTS - rms 02 0. 500 00 0. VOLTS - rms 8 100 3 2 01 03 12 0. F 0. 0. 6 200 F F 1600 V 1200 V 10 10 1 2 5 10 2 5 100 2 5 1000 1 2 5 10 2 5 100 2 5 1000 FREQUENCY - kHz FREQUENCY - kHz STANDARD RATINGS* in inches (millimeters) F 10 % TOLERANCE 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.1 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 SIZE PART NUMBER 715P12392J 715P15392J 715P18392J 715P22392J 715P27392J 715P33392J 715P39392K 715P47392K 715P56392K 715P68392K 715P82392L 715P10492L 715P12492L 715P15492L 715P18492L 715P22492L 715P27492M 715P33492M 715P39492M 715P47492M L 200 VDC/155 VAC** 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.95 [24.13] 0.95 [24.13] 0.95 [24.13] 0.95 [24.13] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] D 0.37 [9.40] 0.37 [9.40] 0.37 [9.40] 0.37 [9.40] 0.42 [10.67] 0.42 [10.67] 0.40 [10.16] 0.40 [10.16] 0.45 [11.43] 0.45 [11.43] 0.45 [11.43] 0.45 [11.43] 0.55 [13.97] 0.55 [13.97] 0.62 [15.75] 0.62 [15.75] 0.65 [16.51] 0.65 [16.51] 0.75 [19.05] 0.75 [19.05] * Bolded items, when ordered as 5 % tolerance with D3 leads, are standard capacitors in stock and available through the Sprague(R) Distribution Network. To complete the Type 715P Part Number, add the "D3" suffix and change the capacitance tolerance code number from a "9" to a "5" to indicate 5 % (i.e., 715P10456LD3). Any other Part Number, value or type may easily be ordered as a Special. ** 60 Hz rms Document Number: 42018 Revision: 13-Feb-07 For technical questions, contact: spresale@vishay.com www.vishay.com 27 Type 715P Vishay Sprague Polypropylene Film Capacitors ORANGE DROP(R), Low Loss STANDARD RATINGS in inches (millimeters) F 10 % TOLERANCE PART NUMBER 0.0039 0.0047 0.0056 0.0068 0.0082 0.01 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.1 0.12 0.15 0.18 0.22 0.27 0.33 0.39 0.47 715P39294J 715P47294J 715P56294J 715P68294J 715P82294J 715P10394J 715P12394J 715P15394J 715P18394K 715P22394K 715P27394K 715P33394K 715P39394L 715P47394L 715P56394L 715P68394L 715P82394L 715P10494L 715P12494L 715P15494L 715P18494M 715P22494M 715P27494M 715P33494M 715P39494M 715P47494M 0.001 0.0012 0.0015 0.0018 0.0022 0.0027 0.0033 0.0039 0.0047 0.0056 0.0068 0.0082 0.01 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.1 0.12 0.15 0.18 0.22 715P10296J 715P12296J 715P15296J 715P18296J 715P22296J 715P27296J 715P33296J 715P39296J 715P47296J 715P56296J 715P68296J 715P82296K 715P10396K 715P12396K 715P15396K 715P18396K 715P22396K 715P27396L 715P33396L 715P39396L 715P47396L 715P56396L 715P68396L 715P82396L 715P10496L 715P12496M 715P15496M 715P18496M 715P22496M SIZE L 400 VDC/200 VAC** 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.95 [24.13] 0.95 [24.13] 0.95 [24.13] 0.95 [24.13] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 600 VDC/200 VAC** 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.95 [24.13] 0.95 [24.13] 0.95 [24.13] 0.95 [24.13] 0.95 [24.13] 0.95 [24.13] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] D 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.45 [11.43] 0.45 [11.43] 0.45 [11.43] 0.45 [11.43] 0.50 [12.70] 0.50 [12.70] 0.50 [12.70] 0.50 [12.70] 0.55 [13.97] 0.55 [13.97] 0.60 [15.24] 0.60 [15.24] 0.65 [16.51] 0.65 [16.51] 0.70 [17.78] 0.70 [17.78] 0.80 [20.32] 0.80 [20.32] 0.90 [22.86] 0.90 [22.86] 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.40 [10.16] 0.45 [11.43] 0.45 [11.43] 0.45 [11.43] 0.45 [11.43] 0.45 [11.43] 0.45 [11.43] 0.50 [12.70] 0.50 [12.70] 0.55 [13.97] 0.55 [13.97] 0.55 [13.97] 0.55 [13.97] 0.60 [15.24] 0.60 [15.24] 0.65 [16.51] 0.65 [16.51] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.75 [19.05] 0.85 [21.59] 0.85 [21.59] * Bolded items, when ordered as 5 % tolerance with D3 leads are standard capacitors in stock and available through the Sprague(R) Distribution Network. To complete the Type 715P Part Number, add the "D3" suffix and change the capacitance tolerance code number from a "9" to a "5" to indicate 5 % (i.e., 715P10456LD3). Any other Part Number, value or type may easily be ordered as a Special. ** 60 Hz rms www.vishay.com 28 For technical questions, contact: spresale@vishay.com Document Number: 42018 Revision: 13-Feb-07 Type 715P Polypropylene Film Capacitors ORANGE DROP(R), Low Loss Vishay Sprague STANDARD RATINGS in inches (millimeters) F 10 % TOLERANCE PART NUMBER 0.0056 0.0068 0.0082 0.01 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.1 715P56298L 715P68298L 715P82298L 715P10398L 715P12398L 715P15398L 715P18398L 715P22398L 715P27398L 715P33398L 715P39398M 715P47398M 715P56398M 715P68398M 715P82398M 715P10498M 0.0027 0.0033 0.0039 0.0047 0.0056 0.0068 0.0082 0.01 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 715P272912L 715P332912L 715P392912L 715P472912L 715P562912L 715P682912L 715P822912L 715P103912L 715P123912L 715P153912L 715P183912M 715P223912M 715P273912M 715P333912M 715P393912M 715P473912M 0.0018 0.0022 0.0027 0.0033 0.0039 0.0047 0.0056 0.0068 0.0082 0.01 0.012 0.015 0.018 0.022 0.027 0.033 715P182916L 715P222916L 715P272916L 715P332916L 715P392916L 715P472916L 715P562916L 715P682916L 715P822916L 715P103916L 715P123916M 715P153916M 715P183916M 715P223916M 715P273916M 715P333916M SIZE L 800 VDC/450 VAC** 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1200 VDC/475 VAC** 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1600 VDC/500 VAC** 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.30 [33.02] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] 1.70 [43.18] D 0.50 [12.70] 0.50 [12.70] 0.50 [12.70] 0.50 [12.70] 0.55 [13.97] 0.55 [13.97] 0.60 [15.24] 0.60 [15.24] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.70 [17.78] 0.80 [20.32] 0.80 [20.32] 0.90 [22.86] 0.90 [22.86] 0.50 [12.70] 0.50 [12.70] 0.50 [12.70] 0.50 [12.70] 0.55 [13.97] 0.55 [13.97] 0.60 [15.24] 0.60 [15.24] 0.65 [16.51] 0.65 [16.51] 0.65 [16.51] 0.65 [16.51] 0.75 [19.05] 0.75 [19.05] 0.85 [21.59] 0.85 [21.59] 0.50 [12.70] 0.50 [12.70] 0.55 [13.97] 0.55 [13.97] 0.60 [15.24] 0.60 [15.24] 0.65 [16.51] 0.65 [16.51] 0.70 [17.78] 0.70 [17.78] 0.75 [19.05] 0.75 [19.05] 0.85 [21.59] 0.85 [21.59] 0.95 [24.13] 0.95 [24.13] * Bolded items, when ordered as 5 % tolerance with D3 leads are standard capacitors in stock and available through the Sprague(R) Distribution Network. To complete the Type 715P Part Number, add the "D3" suffix and change the capacitance tolerance code number from a "9" to a "5" to indicate 5 % (i.e., 715P10456LD3). Any other Part Number, value or type may easily be ordered as a Special. ** 60 Hz rms Document Number: 42018 Revision: 13-Feb-07 For technical questions, contact: spresale@vishay.com www.vishay.com 29 Type 715P Polypropylene Film Capacitors ORANGE DROP(R), Low Loss Vishay Sprague STANDARD MARKING FORMAT SAMPLE MARKING TOLERANCE CODES PER EIA STANDARDS DESCRIPTION d715P200 V 1239 9340 d 715P 200 V 1239 9940 Sprague(R) Indentification Type Number DC Voltage Rating, Volts Capacitance and Tolerance Code Weekly Date Code (i.e. 40th week for 1999) 9 = 10 % 5=5% 2=2% ORDERING INFORMATION 715P TYPE 123 CAPACITANCE 9 TOLERANCE 2 DC VOLTAGE RATING AT + 85 C Capacitance is expressed in picofarads. The first two digits are significant. The third is the number of zeros to follow. Values must conform to Decade Rating for the tolerance specified. 9 = 10 % 5=5% 2=2% This is expressed in hundreds of volts. Example: 715P R5 = 50 volts www.vishay.com 30 J CASE CODE See Dimensional Configurations. For technical questions, contact: spresale@vishay.com D TERMINAL 3 LEAD LENGTH 1 = 0.187" 0.030" A = Straight Lead [4.750 0.762] B = Hairpin Crimped D = Hockey Crimped 2 = 0.250" 0.030" [ 6.350 0.762] 3 = 1.250" [31.750] Minimum Document Number: 42018 Revision: 13-Feb-07 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000