LTST-C150TBKTBINQ - Lite-On Electronics, Inc.

LITE-ON TECHNOLOGY CORPORATION

Property of Lite-On Only

Features

* Meet ROHS, Green Product.

* Package In 8mm Tape On 7" Diameter Reels.

* Compatible With Automatic Placement Equipment.

* Compatible With Infrared And Vapor Phase Reflow Solder Process.

* EIA STD package.

* I.C. compatible.

Package Dimensions

Part No. Lens Source Color

LTST-C150TBKT Water Clear InGaN Blue

Notes:

1. All dimensions are in millimeters (inches).

2. Tolerance is ± 0.10 mm (.004") unless otherwise noted.

Part No. : LTST-C150TBKT Page : 1 of 11

BNS-OD-C131/A4

LITE-ON TECHNOLOGY CORPORATION

Property of Lite-On Only

Absolute Maximum Ratings At Ta=25℃

Parameter LTST-C150TBKT Unit

Power Dissipation 76 mW

Peak Forward Current

(1/10 Duty Cycle, 0.1ms Pulse Width) 100 mA

DC Forward Current 20 mA

Derating Linear From 50°C 0.25 mA/°C

Reverse Voltage 5 V

Operating Temperature Range -20°C to + 80°C

Storage Temperature Range -30°C to + 100°C

Wave Soldering Condition 260°C For 5 Seconds

Infrared Soldering Condition 260°C For 5 Seconds

Vapor Phase Soldering Condition 215°C For 3 Minutes

Part No. : LTST-C150TBKT Page : 2 of 11

BNS-OD-C131/A4

LITE-ON TECHNOLOGY CORPORATION

Property of Lite-On Only

Suggestion Profile:

(1) Suggestion IR Reflow Profile For Normal Process

(2) Suggestion IR Reflow Profile For Pb Free Process

Recom m ended Profile Betw een Assem ble And H eat-Resistance Line

T h e P ro file is a v aila b le th a t mu s t to u s e S n A g C u s o ld er p a s te

Part No. : LTST-C150TBKT Page : 3 of 11

BNS-OD-C131/A4

LITE-ON TECHNOLOGY CORPORATION

Property of Lite-On Only

Electrical Optical Characteristics At Ta=25℃

Parameter Symbol

Part No.

LTST- Min. Typ. Max. Unit Test Condition

Luminous Intensity IV C150TBKT 28.0 - 112.0 mcd IF = 20mA

Note 1

Viewing Angle 2θ1/2 C150TBKT 130 deg Note 2 (Fig.6)

Peak Emission Wavelength λP C150TBKT 468 nm

Measurement

@Peak (Fig.1)

Dominant Wavelength λd C150TBKT 465.0 - 475.0 nm IF = 20mA

Note 3

Spectral Line Half-Width Δλ C150TBKT 25 nm

Forward Voltage VF C150TBKT 2.80 - 3.80 V IF = 20mA

Reverse Current IR C150TBKT 10 μA VR = 5V

Notes: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the

CIE eye-response curve.

2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity.

3. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the

single wavelength which defines the color of the device.

4. Caution in ESD:

Static Electricity and surge damages the LED. It is recommend to use a wrist band or anti-electrostatic

glove when handling the LED. All devices, equipment and machinery must be properly grounded.

Part No. : LTST-C150TBKT Page : 4 of 11

BNS-OD-C131/A4

LITE-ON TECHNOLOGY CORPORATION

Property of Lite-On Only

Bin Code List

Part No. : LTST-C150TBKT Page : 5 of 11

BNS-OD-C131/A4

Forward Voltage Unit: V @20mA

Bin Code Min. Max.

D7 2.80 3.00

D8 3.00 3.20

D9 3.20 3.40

D10 3.40 3.60

D11 3.60 3.80

Tolerance on each Forward Voltage bin is +/-0.1 volt

Luminous Intensity Unit : mcd @20mA

Bin Code Min. Max.

N 28.0 45.0

P 45.0 71.0

Q 71.0 112.0

Tolerance on each Intensity bin is +/-15%

Dominant Wavelength Unit : nm @20mA

Bin Code Min. Max.

AC 465.0 470.0

AD 470.0 475.0

Tolerance for each Dominate Wavelength bin is +/- 1nm

LITE-ON TECHNOLOGY CORPORATION

Property of Lite-On Only

Typical Electrical / Optical Characteristics Curves

(25 °C Ambient Temperature Unless Otherwise Noted)

Part No. : LTST-C150TBKT Page : 6 of 11

BNS-OD-C131/A4

LITE-ON TECHNOLOGY CORPORATION

Property of Lite-On Only

Cleaning

Do not use unspecified chemical liquid to clean LED they could harm the package.

If clean is necessary, immerse the LED in ethyl alcohol or in isopropyl alcohol at normal temperature

for less one minute.

Suggest Soldering Pad Dimensions

Package Dimensions Of Tape And Reel

Notes:

1. All dimensions are in millimeters (inches).

Part No. : LTST-C150TBKT Page : 7 of 11

BNS-OD-C131/A4

LITE-ON TECHNOLOGY CORPORATION

Property of Lite-On Only

Notes:

1. Empty component pockets sealed with top cover tape.

2. 7 inch reel-3000 pieces per reel.

3. Minimum packing quantity is 500 pcs for remainders.

4. The maximum number of consecutive missing lamps is two.

5. In accordance with ANSI/EIA 481-1-A-1994 specifications.

Part No. : LTST-C150TBKT Page : 8 of 11

BNS-OD-C131/A4

LITE-ON TECHNOLOGY CORPORATION

Property of Lite-On Only

Part No. : LTST-C150TBKT Page : 9 of 11

BNS-OD-C131/A4

CAUTIONS

1. Application

The LEDs described here are intended to be used for ordinary electronic equipment (such as office

equipment, communication equipment and household applications).Consult Liteon’s Sales in advance

for information on applications in which exceptional reliability is required, particularly when the failure

or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation,

traffic control equipment, medical and life support systems and safety devices).

2. Storage

The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity.

It is recommended that LEDs out of their original packaging are IR-reflowed within one week.

For extended storage out of their original packaging, it is recommended that the LEDs be stored in a

sealed container with appropriate desiccant, or in a desiccators with nitrogen ambient.

LEDs stored out of their original packaging for more than a week should be baked at about 60 deg C

for at least 24 hours before solder assembly.

3. Cleaning

Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED if necessary.

4. Soldering

Recommended soldering conditions:

Reflow soldering Wave Soldering Soldering iron

Pre-heat

Pre-heat time

Peak temperature

Soldering time

120~150°C

120 sec. Max.

240°C Max.

10 sec. Max.

Pre-heat

Pre-heat time

Solder wave

Soldering time

100°C Max.

60 sec. Max.

260°C Max.

10 sec. Max.

Temperature

Soldering time 300°C Max.

3 sec. Max.

(one time only)

5. Drive Method

An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs

connected in parallel in an application, it is recommended that a current limiting resistor be incorporated

in the drive circuit, in series with each LED as shown in Circuit A below.

Circuit model A Circuit model B

LED

(A) Recommended circuit.

(B) The brightness of each LED might appear different due to the differences in the I-V characteristics

of those LEDs.

6. ESD (Electrostatic Discharge)

Static Electricity or power surge will damage the LED.

Suggestions to prevent ESD damage:

 Use of a conductive wrist band or anti-electrostatic glove when handling these LEDs.

 All devices, equipment, and machinery must be properly grounded.

 Work tables, storage racks, etc. should be properly grounded.

 Use ion blower to neutralize the static charge which might have built up on surface of the LED’s

plastic lens as a result of friction between LEDs during storage and handling.

LITE-ON TECHNOLOGY CORPORATION

Property of Lite-On Only

Part No. : LTST-C150TBKT Page : 10 of 11

BNS-OD-C131/A4

ESD-damaged LEDs will exhibit abnormal characteristics such as high reverse leakage current, low forward

voltage, or “ no lightup ” at low currents.

To verify for ESD damage, check for “ lightup ” and Vf of the suspect LEDs at low currents.

The Vf of “ good ” LEDs should be >2.0V@0.1mA for InGaN product and >1.4V@0.1mA for AlInGaP product.

7. Reliability Test

Classification Test Item Test Condition Reference Standard

Operation Life Ta= Under Room Temperature As Per Data Sheet

Maximum Rating

*Test Time= 1000HRS (-24HRS,+72HRS)*@20mA.

MIL-STD-750D:1026

MIL-STD-883D:1005

JIS C 7021:B-1

High Temperature

High Humidity

Storage

IR-Reflow In-Board, 2 Times

Ta= 65±5℃,RH= 90～95%

*Test Time= 240HRS±2HRS

MIL-STD-202F:103B

JIS C 7021:B-11

High Temperature

Storage Ta= 105±5℃

*Test Time= 1000HRS (-24HRS,+72HRS) MIL-STD-883D:1008

JIS C 7021:B-10

Endurance

Test

Low Temperature

Storage Ta= -55±5℃

*Test Time=1000HRS (-24HRS,+72H RS) JIS C 7021:B-12

Temperature

Cycling

105℃ ～ 25℃ ～ -55℃ ～ 25℃

30mins 5mins 30mins 5mins

10 Cycles

MIL-STD-202F:107D

MIL-STD-750D:1051

MIL-STD-883D:1010

JIS C 7021:A-4

Thermal

Shock

IR-Reflow In-Board, 2 Times

85 ± 5℃ ～ -40℃ ± 5℃

10mins 10mins 10 Cycles

MIL-STD-202F:107D

MIL-STD-750D:1051

MIL-STD-883D:1011

Solder

Resistance T.sol= 260 ± 5℃

Dwell Time= 10 ± 1secs

MIL-STD-202F:210A

MIL-STD-750D:2031

JIS C 7021:A-1

IR-Reflow

Normal Process

Ramp-up rate(183℃ to Peak) +3℃/ second max

Temp. maintain at 125(±25)℃ 120 seconds max

Temp. maintain above 183℃ 60-150 seconds

Peak temperature range 235℃+5/-0℃

Time within 5°C of actual Peak Temperature (tp)

10-30 seconds

Ramp-down rate +6℃/second max

MIL-STD-750D:2031.2

J-STD-020

IR-Reflow

Pb Free Process

Ramp-up rate(217 to Peak) +3 / second max℃℃

Temp. maintain at 175(±25) 180 seconds max℃

Temp. maintain above 217 60℃-150 seconds

Peak temperature range 260 +0/℃-5℃

Time within 5°C of actual Peak Temperature (tp)

20-40 seconds

Ramp-down rate +6 /second max℃

MIL-STD-750D:2031.2

J-STD-020

Environmental

Test

Solderability

T.sol= 235 ± 5℃

Immersion time 2±0.5 sec

Immersion rate 25±2.5 mm/sec

Coverage ≧95% of the dipped surface

MIL-STD-202F:208D

MIL-STD-750D:2026

MIL-STD-883D:2003

IEC 68 Part 2-20

JIS C 7021:A-2

8. Others

The appearance and specifications of the product may be modified for improvement without prior notice.

LITE-ON TECHNOLOGY CORPORATION

Property of Lite-On Only

9. Suggested Checking List

Training and Certification

1. Everyone working in a static-safe area is ESD-certified?

2. Training records kept and re-certification dates monitored?

Static-Safe Workstation & Work Areas

1. Static-safe workstation or work-areas have ESD signs?

2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V?

3. All ionizer activated, positioned towards the units?

4. Each work surface mats grounding is good?

Personnel Grounding

1. Every person (including visitors) handling ESD sensitive (ESDS) items wears wrist strap, heel

strap or conductive shoes with conductive flooring?

2. If conductive footwear used, conductive flooring also present where operator stand or walk?

3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*?

4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DLs?

5. All wrist strap or heel strap checkers calibration up to date?

Note: *50V for Blue LED.

Device Handling

1. Every ESDS items identified by EIA-471 labels on item or packaging?

2. All ESDS items completely inside properly closed static-shielding containers when not at

static-safe workstation?

3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items?

4. All flexible conductive and dissipative package materials inspected before reuse or recycles?

Others

1. Audit result reported to entity ESD control coordinator?

2. Corrective action from previous audits completed?

3. Are audit records complete and on file?

Part No. : LTST-C150TBKT Page : 11 of 11

BNS-OD-C131/A4