Not for new design. Use new F611-F612 Series. Loose Taped Fig.1 R66 MKT Series Fig. 2 METALLIZED POLYESTER FILM CAPACITOR D.C MULTIPURPOSE APPLICATIONS Typical applications: this series combines small size, good performances in by-passing, blocking and interference suppression in low voltage applications (i.e.: AUTOMOTIVE). p = 7.5mm PRODUCT CODE: R66 Note: R66 series has replaced the R84 series (available only upon request). For new design we suggest the use of the R66 series B Od 0.05 <3.5 0.5 Pitch Box thickness (B) (mm) (mm) 4.0 0.6 7.5 All dimensions are in mm. All Maximum dimensions (mm) B max H max L max B +0.1 H +0.1 L +0.2 GENERAL TECHNICAL DAta Dielectric: polyester film (polyethylene terephthalate). Plates: aluminium layer deposited by evaporation under 1 2 3 4 5 6 7 8 9 10 11 12 13 14 vacuum. Winding: non-inductive type. D R 6 6 Leads: tinned wire. Protection: plastic case, thermosetting resin filled. Digit 1 to 3 Series code. Box material is solvent resistant and flame Digit 4 d.c. rated voltage: retardant according to UL94. C = 50V D = 63VE= 100V Marking: Capacitance, tolerance, D.C. rated voltage. I = 250V M = 400V P = 630V Climatic category: 55/105/56 IEC 60068-1 Digit 5 Pitch: D = 7.5 mm Operating temperature range: -55 to +105C For stacked technology an upper operating Digit 6 to 9 Digits 7 - 8 - 9 indicate the first three digits of temperature of +125C is allowed for a max operating Capacitance value and the 6th digit indicates time of 1000 h. the number of zeros that must be added to Related documents: IEC 60384-2 obtain the Rated Capacitance in pF. Digit 10 to 11 Mechanical version and/or packaging (table1) Digit 12 Identifies the dimensions and electrical characteristics. Winding scheme Digit 13 Internal use Capacitance tolerance: Digit 14 J=5%; K=10%; M=20%. Product code system The part number, comprising 14 digits, is formed as follows: Table 1 (for more detailed information, please refer to page 14). Standard packaging style Lead length Taping style Ordering code (mm) Figure No. (Digit 10 to 11) 1 2 DQ 28 1 CK AMMO-PACK AMMO-PACK Reel O 355 mm Loose, short leads Loose, long leads 09/2008 4 17+1/-2 +2 single sided metallized polyester film AA Z3 36 Not for new design. Use new F611-F612 Series. R66 MKT Series METALLIZED POLYESTER FILM CAPACITOR D.C. MULTIPURPOSE APPLICATIONS p = 7.5 mm PRODUCT CODE: R66 STACKED VERSION Rated Cap. 50Vdc/30Vac Std dimensions B H L p Max dv/dt Max K0 (V/ s) (V2/ s) 0.68 F 3.0 8.0 10.0 7.5 100 10 E3 1.0 F 3.0 8.0 10.0 7.5 100 10 E3 1.5 F 4.0 9.0 10.0 7.5 100 10 E3 2.2 F 5.0 10.5 10.0 7.5 100 10 E3 4.7 F 6.0 12.0 10.5 7.5 100 10 E3 Rated Cap. 63Vdc/40Vac Std dimensions B H L Max dv/dt Max K0 p (V/ s) (V2/ s) 0.33 F 3.0 8.0 10.0 7.5 120 15 E3 0.47 F 3.0 8.0 10.0 7.5 120 15 E3 0.68 F 4.0 9.0 10.0 7.5 120 15 E3 1.0 F 4.0 9.0 10.0 7.5 120 15 E3 1.5 F 5.0 10.5 10.0 7.5 120 15 E3 2.2 F 6.0 12.0 10.5 7.5 120 15 E3 3.3 F 6.0 12.0 10.5 7.5 120 15 E3 Max dv/dt Max K0 (V/ s) (V / s) Rated Cap. 100Vdc/63Vac Std dimensions B H L p Part Number Rated Cap. B R66CD3680--6-- R66CD 4100--6-R66CD 4150--6-R66CD 4220--6-R66CD 4470--6-Part Number R66DD 3330--7-- 0.068F 3.0 8.0 10.0 7.5 150 30 E3 3.0 8.0 10.0 7.5 150 30 E3 0.15 F 3.0 8.0 10.0 7.5 150 30 E3 0.22 F 3.0 8.0 10.0 7.5 150 30 E3 0.33 F 4.0 9.0 10.0 7.5 150 30 E3 0.47 F 4.0 9.0 10.0 7.5 150 30 E3 0.68 F 4.0 9.0 10.0 7.5 150 30 E3 1.0 F 5.0 10.5 10.0 7.5 150 30 E3 1.5 F 6.0 12.0 10.5 7.5 150 30 E3 Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) H L Max dv/dt Max K0 (V2/ s) p (V/ s) 0.022F 3.0 8.0 10.0 7.5 200 100 E3 0.033F 3.0 8.0 10.0 7.5 200 100 E3 0.047F 3.0 8.0 10.0 7.5 200 100 E3 0.068F 3.0 8.0 10.0 7.5 200 100 E3 0.10 F 4.0 9.0 10.0 7.5 200 100 E3 0.15 F 4.0 9.0 10.0 7.5 200 100 E3 0.22 F 5.0 10.5 10.0 7.5 200 100 E3 0.33 F 6.0 12.0 10.5 7.5 200 100 E3 Rated Cap. 6800 pF 400Vdc/200Vac Std dimensions B H L p 3.0 8.0 10.0 7.5 R66DD 4150--7-- 0.010 F 3.0 8.0 10.0 7.5 275 220 E3 0.015 F 3.0 8.0 10.0 7.5 275 220 E3 R66DD 4330--6-- 0.022 F 3.0 8.0 10.0 7.5 275 220 E3 0.033 F 4.0 9.0 10.0 7.5 275 220 E3 0.047 F 4.0 9.0 10.0 7.5 275 220 E3 0.068 F 5.0 10.5 10.0 7.5 275 220 E3 0.10 F 6.0 12.0 10.5 7.5 275 220 E3 0.15 F 6.0 12.0 10.5 7.5 275 220 E3 R66DD 3470--6-R66DD 3680--7-R66DD 4100--7-R66DD 4220--6-Part Number 2 0.10 F 250Vdc/160Vac Std dimensions R66ED 2680--7-R66ED 3100--7-R66ED 3150--7-R66ED 3220--7-R66ED 3330--7-- Part Number R66ID 2220--7-- R66ID 2330--7-- R66ID 2470--7-R66ID 2680--6-- R66ID 3100--7-R66ID 3150--7-- R66ID 3220--7-- R66ID 3330--6-- Max dv/dt (V/s) 275 Max K0 Part Number (V2/s) 220 E3 R66MD1680--7-R66MD2100--7-R66MD2150--7-R66MD2220--6-R66MD2330--7-R66MD2470--7-R66MD2680--7-R66MD3100--6-R66MD3150--6-- Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) R66ED 3470--7-R66ED 3680--7-R66ED 4100--7-R66ED 4150--6-- a) WOUND version b) STACKED version Rated Cap. 630Vdc/220Vac* Std dimensions B H L p a) 1000 pF 3.0 8.0 10.0 7.5 Max dv/dt (V/s) 40 Max K0 (V2/s) 50 E3 a) 1500 pF 3.0 8.0 10.0 7.5 40 50 E3 a) 2200 pF 3.0 8.0 10.0 7.5 40 50 E3 a) 3300 pF 3.0 8.0 10.0 7.5 40 50 E3 a) 4700 pF 3.0 8.0 10.0 7.5 40 50 E3 a) 6800 pF 4.0 9.0 10.0 7.5 40 50 E3 b) 0.010F 4.0 9.0 10.0 7.5 300 378 E3 b) 0.015F 4.0 9.0 10.0 7.5 300 378 E3 b) 0.022F 5.0 10.5 10.0 7.5 300 378 E3 b) 0.033F 6.0 12.0 10.5 7.5 300 378 E3 b) 0.047F 6.0 12.0 10.5 7.5 300 378 E3 Part Number R66PD 1100--1-R66PD1150--1-- R66PD 1220--1-- R66PD 1330--1-- R66PD 1470--1-- R66PD 1680--1-- R66PD 2100--7-- R66PD 2150--7-- R66PD 2220--7-- R66PD 2330--6-- R66PD 2470--6-- Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) All dimensions are in mm. Note: If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The pulse characteristic K0 depends on the voltage wave-form and in any case it cannot overcome the value given in the above table. *Not suitable for across-the-line applications. Please refer to Interference Suppression Capacitors (page 145). 37 09/2008 Not for new design. Use new F611-F612 Series. R66 MKT Series METALLIZED POLYESTER FILM CAPACITOR D.C. MULTIPURPOSE APPLICATIONS p = 7.5 mm PRODUCT CODE: R66 electrical characteristics test method and performance Rated voltage (VR): Damp heat, steady state: 50 Vdc 63 Vdc 100 Vdc 250 Vdc 400 Vdc 630 Vdc Rated temperature (TR): +85 C Temperature derated voltage: for temperatures between +85C and the upper operating temperature ( +105C for wound technology and +125C for stacked technology) a decreasing factor of 1.25% per degree C on the rated voltage VR (d.c. and a.c.) has to be applied. Capacitance range: Capacitance values: Test conditions Temperature: Relative humidity (RH): Test duration: Performance Capacitance change |C/C|: DF change (tg): Insulation resistance: 1000 pF to 4.7 F +40C 2C 93% 2% 56 days 5% 50x10-4 at 1kHz 50% of initial limit. Endurance: Test conditions Temperature: Test duration: Voltage applied: Performance Capacitance change |C/C|: DF change (tg): Insulation resistance: E6 series (IEC 60063 Norm). Capacitance tolerances (measured at 1 kHz): 5% (J); 10% (K); 20% (M). Total self-inductance (L): 8nH (lead length ~2mm) Dissipation factor (DF): tgd 10-4. at +25C "5C +105C 2C 2000 h 1.25xVC 5% 50 10-4 at 10kHz 50% of initial limit. Resistance to soldering heat: kHz tg x 10-4 1 10 100 150 Insulation resistance: Test conditions Temperature Voltage charge time: Voltage charge: +25C5C 1 min 50 Vdc for VR <100 Vdc 100 Vdc for VR 100 Vdc Performance For VR 100 Vdc 3750 M for C 0.33F (5000 M)* 1250 s for C >0.33F (5000 s)* For VR >100 Vdc 30000M (50000 M)* *Typical value Test voltage between terminals: 1.6xVR applied for 2 s at +25C 5C 09/2008 Test conditions Solder bath temperature: +260C5C Dipping time (with heat screen):10 s 1 s Performance Capacitance change |C/C|: 2% DF change (tg): 50x10-4 at 10kHz Insulation resistance: initial limit. Long term stability (after two years): Storage standard environmental conditions (see page 12). Performance Capacitance change |C/C|: 3% for C0.1F 2% for C>0.1F Reliability Reference MIL HDB 217 Application conditions: Temperature: +40C2C Voltage: 0.5xVR Failure rate: 2 FIT (1 FIT = 1 10-9 failures/components h) Failure criteria: (according to DIN 44122) Short or open circuit Capacitance change |C/C|: >10% DF change (tg): >2 x initial limit. Insulation resistance: <0.005 x initial limit. 38 Not for new design. Use new F611-F612 Series. R66 MKT Series METALLIZED POLYESTER FILM CAPACITOR D.C. MULTIPURPOSE APPLICATIONS p = 7.5 mm PRODUCT CODE: R66 MAX. VOLTAGE (Vr.m.s.) VERSUS FREQUENCY (sinusoidal wave-form / Th 40C) Note: p (pitch) in mm. 39 09/2008 Not for new design. Use new F611-F612 Series. R66 MKT Series METALLIZED POLYESTER FILM CAPACITOR D.C. MULTIPURPOSE APPLICATIONS p = 7.5 mm PRODUCT CODE: R66 MAX. CURRENT (Ir.m.s.) VERSUS FREQUENCY (sinusoidal wave-form / Th 40C) Digitally signed by Marcy Brand DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corporation, ou=Marketing Communications, cn=Marcy Brand, email=marcybrand@kemet.com Date: 2012.07.18 12:11:04 -04'00' Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute - and we specifically disclaim - any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by us with reference to the use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained. Note: p (pitch) in mm. 09/2008 40