Performance Characteristics
Item
SOLID TANTALUM ELECTROLYTIC CAPACITORS
F93Resin-molded Chip,
Standard Series
∗As for the surge and derated voltage at 125
˚C
, refer to page 308 for details.
Type numbering system(Example: 10V 10µF)
Drawing
Dimensions
Marking
Specifications
Category
Temperature Range --55 to +125
˚C
(Rated temperature : +85
˚C
)
Capacitance Tolerance ±20%, ±10% (at 120Hz)
Dissipation Factor
(120Hz)
Refer to next page
ESR (100kHz) Refer to next page
Leakage Current
•
After 1 minute's application of rated voltage, leakage current
at 20
˚C
is not more than 0.01CV or 0.5µA, whichever is greater.
•
After 1 minute's application of rated voltage, leakage current
at 85
˚C
is not more than 0.1CV or 5µA, whichever is greater.
•
After 1 minute's application of derated voltage, leakage current
at 125
˚C
is not more than 0.125CV or 6.3µA, whichever is greater.
Capacitance Change
by Temperature +15% Max. (at +125
˚C
)
+10% Max. (at +85
˚C
)
--10% Max. (at --55
˚C
)
Damp Heat
(Steady State)
At 40
˚C
90 to 95% R.H. 500 hours (No voltage applied)
Capacitance Change...Refer to next page (* 1)
Dissipation Factor........Initial specified value or less
Leakage Current..........Initial specified value or less
Temperature Cycles
--55
˚C
/ +125
˚C
30 minutes each 5 cycles
Capacitance Change...Refer to next page (* 1)
Dissipation Factor........Initial specified value or less
Leakage Current..........Initial specified value or less
Resistance
to Soldering Heat
Test condition:
10 seconds reflow at 260
˚C ,
5 seconds immersion at 260
˚C
Capacitance Change...Refer to next page (* 1)
Dissipation Factor........Initial specified value or less
Leakage Current..........Initial specified value or less
Surge∗
After application of surge voltage in series with a 33Ωresistor at the rate of
30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at
85
˚C
,capacitors meet the characteristics requirements listed below.
Capacitance Change.....Refer to next page (* 1)
Dissipation Factor.........Initial specified value or less
Leakage Current...........Initial specified value or less
Endurance∗
After 2000 hours' application of rated voltage in series with a 3
Ω
resistor
at 85
˚C
, or derated voltage in series with a 3
Ω
resistor at 125
˚C
,
capacitors meet the characteristic requirements listed below.
Capacitance Change......Refer to next page (* 1)
Dissipation Factor..........Initial specified value or less
Leakage Current............Initial specified value or less
Shear Test
After applying the pressure load of 5N for 10±1 seconds
horizontally to the center of capacitor side body which has no
electrode and has been soldered
beforehand on an aluminum substrate,
there shall be found neither exfoliation nor
its sign at the terminal electrode.
Terminal Strength
Keeping a capacitor surface-mounted on a substrate upside down
and supporting the substrate at both of the opposite bottom points
45mm apart from the center of the
capacitor, the pressure strength is
applied with a specified jig at the
center of the substrate so that the
substrate may bend by 1mm as
illustrated. Then, there shall be found
no remarkable abnormality on the
capacitor terminals.
Case code L W1W2HS
A 3.2±0.2 1.6±0.2 1.2±0.1 1.6±0.2 0.8±0.2
B 3.5±0.2 2.8±0.2 2.2±0.1 1.9±0.2 0.8±0.2
C 6.0±0.2 3.2±0.2 2.2±0.1 2.5±0.2 1.3±0.2
N 7.3 ± 0.2 4.3 ± 0.2 2.4 ± 0.1 2.8 ± 0.2 1.3 ± 0.2
(mm)
( ) The series in parentheses are being developed.
Please contact to your local Nichicon sales office when these
series are being designed in your application.
Taping code
(Refer to page 309 for details)
F
19
23
31
4A
51
60
76
8M
9A
10 11
Case code
Capacitance tolerance
Rated capacitance Rated voltage
Series
L
H
SS
W2
W1
L
H
SS
W2
W1
A •B Case C•N Case
Capacitance (µF)
Rated voltage (V)Rated voltage (V)
A Case B Case C Case N Case
(Rated voltage code) (Capacitance code)
C685 22
16V
47
16V
100
16V
2.5V e
G
J
A
C
4V
6.3V
10V
16V
20V D
E
V
25V
35V
5N (0.51kg ¥f)
For 10±1 seconds
20
R230
45 45
1
mm
Standard Ratings
Compliant to the RoHS directive (2002/95/EC).
0.47
0.68
1
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
68
100
150
220
330
470
680
474
684
105
155
225
335
475
685
106
156
226
336
476
686
107
157
227
337
477
687
A
A
A
A
A•B
B
(A) •B•C
C
N
N
A
A
A
A
A
A
A•B
A•B
A•B•C
B•C
B•C•N
N
N
A
A
A
A•B
A•B
A•B
A•B•C
B•C
B•C•N
C•N
N
N
A
A
A
A
A
A•B
A•B
A•B•C
B•C
(B) •C•N
N
C•N
N
N
A
A
A•B
A•B
A•B
C
B•C
C•N
C•N
(N)
A
A
A
A
A•B
B
B•C
C
C
N
N
4
0G 6.3
0J 10
1A 16
1C 20
1D 25
1E 35
1V
Cap.(
µ
F)
Code V
A
A
A
A
A
A•B
B•C
C
C•N
N
N
CAT.8100Y-1
SOLID TANTALUM ELECTROLYTIC CAPACITORS
F93
Standard Ratings
In case of capacitance tolerance ±10% type, K will be put at 9th digit of type
numbering system.
*1 : ∆C/C
I t e m A • B • C • N Case (%)
Damp Heat ±10
Tempereature cycles ±5
Resistance soldering heat
±5
Surge ±5
Endurance ±10
4.7 A F931A475MAA 0.5 6 4.0 *
6.8 A F931A685MAA 0.7 6 3.5 *
10 A F931A106MAA 1.0 6 3.0 *
15 A F931A156MAA 1.5 8 2.9 *
15 B F931A156MBA 1.5 6 2.0 *
22 A F931A226MAA 2.2 12 2.5 *
22 B F931A226MBA 2.2 6 1.9 *
33 A F931A336MAA 3.3 18 2.5 *
33 B F931A336MBA 3.3 8 1.4 *
47 A F931A476MAA 4.7 40 2.0 ±15
47 B F931A476MBA 4.7 8 1.0 *
47 C F931A476MCC 4.7 6 0.9 *
68 B F931A686MBA 6.8 12 0.9 ±15
68 C F931A686MCC 6.8 8 0.8 *
100 B F931A107MBA 10.0 18 1.2 ±15
100 C F931A107MCC 10.0 10 0.7 *
100 N F931A107MNC 10.0 8 0.6 *
150 C F931A157MCC 15.0 14 0.7 *
150 N F931A157MNC 15.0 10 0.6 *
220 N F931A227MNC 22.0 12 0.5 *
330 N F931A337MNC 33.0 18 0.5 *
4.7 A F930J475MAA 0.5 6 4.0 *
6.8 A F930J685MAA 0.5 6 3.5 *
10 A F930J106MAA 0.6 6 3.0 *
15 A F930J156MAA 0.9 6 2.9 *
22 A F930J226MAA 1.4 8 2.5 *
33 A F930J336MAA 2.1 8 2.5 *
47 A F930J476MAA 3.0 18 2.5 *
47 B F930J476MBA 3.0 6 1.0 *
68 A F930J686MAA 4.3 20 2.0 *
68 B F930J686MBA 4.3 8 1.0 *
100 A F930J107MAA 6.3 35 2.0 ±15
100 B F930J107MBA 6.3 14 0.9 *
100 C F930J107MCC 6.3 8 0.7 *
150 B F930J157MBA 9.5 18 0.9 *
150 C F930J157MCC 9.5 12 0.7 *
220 B F930J227MBA 13.9 30 1.2 ±15
220 C F930J227MCC 13.9 14 0.7 *
220 N F930J227MNC 13.9 10 0.5 *
330 N F930J337MNC 20.8 14 0.5 *
470 N F930J477MNC 29.6 16 0.3 *
22 A F930G226MAA 0.9 6 2.5 *
33 A F930G336MAA 1.3 8 2.5 *
47 A F930G476MAA 1.9 18 2.5 *
68 A F930G686MAA 2.7 24 2.5 *
100 A F930G107MAA 4.0 30 2.0 *
100 B F930G107MBA 4.0 14 0.9 *
150 B F930G157MBA 6.0 16 0.7 *
220 B F930G227MBA 8.8 18 0.7 *
220 C F930G227MCC 8.8 12 0.7 *
330 C F930G337MCC 13.2 14 0.7 *
470 N F930G477MNC 18.8 16 0.3 *
680 N F930G687MNC 27.2 18 0.3 *
4V
6.3
V
*1
∆C/C
(%)
Part Number
Leakage
Current
(
µ
A)
Disspation
Factor
(%@120Hz)
Case
code ESR
(
Ω
@100kHz)
Rated Volt
Rated
Capacitance
(
µ
F)
33 B F931C336MBA 5.3 8 1.9 *
33 C F931C336MCC 5.3 6 1.1 *
47 C F931C476MCC 7.5 8 0.9 *
47 N F931C476MNC 7.5 6 0.7 *
68 N F931C686MNC 10.9 6 0.6 *
100 C F931C107MCC 16.0 15 0.7 ±10
100 N F931C107MNC 16.0 10 0.6 *
150 N F931C157MNC 24.0 15 0.6 *
220 N F931C227MNC 35.2 25 0.7 ±10
0.47 A F931V474MAA 0.5 4 10.0 *
0.68 A F931V684MAA 0.5 4 7.6 *
1 A F931V105MAA 0.5 4 7.5 *
1.5 A F931V155MAA 0.5 6 7.5 *
2.2 A F931V225MAA 0.8 6 7.0 *
2.2 B F931V225MBA 0.8 4 3.8 *
3.3 B F931V335MBA 1.2 4 3.5 *
4.7 B F931V475MBA 1.6 8 3.1 *
4.7 C F931V475MCC 1.6 6 1.8 *
6.8 C F931V685MCC 2.4 6 1.8 *
10 C F931V106MCC 3.5 6 1.6 *
15 N F931V156MNC 5.3 6 0.7 *
22 N F931V226MNC 7.7 8 0.7 *
0.68 A F931E684MAA 0.5 4 7.6 *
1 A F931E105MAA 0.5 4 7.5 *
1.5 A F931E155MAA 0.5 4 6.7 *
2.2 A F931E225MAA 0.6 6 6.3 *
3.3 A F931E335MAA 0.8 6 6.0 *
4.7 A F931E475MAA 1.2 8 4.0 *
4.7 B F931E475MBA 1.2 6 2.8 *
10 B F931E106MBA 2.5 12 1.9 *
10 C F931E106MCC 2.5 6 1.5 *
15 C F931E156MCC 3.8 8 1.2 *
22 C F931E226MCC 5.5 8 1.1 *
22 N F931E226MNC 5.5 6 0.7 *
33 N F931E336MNC 8.3 8 0.7 *
47 N F931E476MNC 11.8 8 0.7 *
2.2 A F931D225MAA 0.5 4 5.0 *
3.3 A F931D335MAA 0.7 4 4.5 *
4.7 A F931D475MAA 0.9 6 3.0 *
4.7 B F931D475MBA 0.9 6 2.8 *
6.8 A F931D685MAA 1.4 6 3.5 *
6.8 B F931D685MBA 1.4 6 2.5 *
10 A F931D106MAA 2.0 8 3.5 *
10 B F931D106MBA 2.0 6 2.1 *
15 C F931D156MCC 3.0 6 1.2 *
22 B F931D226MBA 4.4 8 1.9 *
22 C F931D226MCC 4.4 8 1.1 *
33 C F931D336MCC 6.6 8 1.1 *
33 N F931D336MNC 6.6 6 0.7 *
47 C F931D476MCC 9.4 10 1.1 *
47 N F931D476MNC 9.4 8 0.7 *
20V
25V
35
V
*1
∆C/C
(%)
Part Number
Leakage
Current
(
µ
A)
Disspation
Factor
(%@120Hz)
Case
code ESR
(
Ω
@100kHz)
Rated Volt
Rated
Capacitance
(
µ
F)
10
V
16
V
1.5 A F931C155MAA 0.5 4 6.0 *
2.2 A F931C225MAA 0.5 4 5.0 *
3.3 A F931C335MAA 0.5 4 4.5 *
4.7 A F931C475MAA 0.8 6 4.0 *
6.8 A F931C685MAA 1.1 6 3.5 *
10 A F931C106MAA 1.6 6 3.0 *
10 B F931C106MBA 1.6 6 2.0 *
15 A F931C156MAA 2.4 10 3.0 *
15 B F931C156MBA 2.4 6 2.0 *
22 A F931C226MAA 3.5 15 3.0 ±15
22 B F931C226MBA 3.5 8 1.9 *
22 C F931C226MCC 3.5 6 1.1 *
16
V
CAT.8100Y-1
