REVISION B DESIGNED & DIMENSIONED IN MILLIMETERS[INCHES] SMP-J-B-XX-ST-XXXX DO NOT SCALE FROM THIS PRINT GENDER -J: JACK B TYPE -B: BULLET C +0.12 0.05 - 0.05 LENGTH -0645: 6.45MM *-0700: 7.00MM *-1000: 10.00MM -1450: 14.50MM +0.12 1 +.005 .002 - .002 2 ORIENTATION -ST: STRAIGHT PLATING SPECIFICATION (VALUES GIVEN ARE IN MICRO-INCHES) -HG: HEAVY GOLD / GOLD 30 Au / 50 Ni MIN ON PIN 10 Au / 50 Ni MIN ON OUTER CONTACT -GF: GOLD / FLASH GOLD 10 Au / 50 Ni MIN ON PIN 3 Au / 50 Ni MIN ON OUTER CONTACT (SEE TABLE 1) * = NOT TOOLED +.005 0.05 - 0.05 .002 - .002 (FROM SHELL TO CONTACT) 3 (FROM SHELL TO INSULATOR, SEE NOTE 4) B C +0.12 +.005 0.05 - 0.05 .002 - .002 (FROM SHELL TO INSULATOR) SECTION "A"-"A" B C +0.25 +.010 "B" 0.00 "B" - .000 (RECOMMENDED PLUG TO PLUG SPACING) "A" "A" 3.40 .134 REF "A" REF NOTES: 1. C REPRESENTS A CRITICAL DIMENSION. 2. MINIMUM PUSHOUT FORCE FOR CENTER CONTACT: 6.67 N [1.5 LB]. INSULATOR: 6.67 N [1.5 LB]. 3. PRODUCT TO BE PACKAGED PER PACKING STANDARD CO-HD-WI-3040-M. TRAY: TY-SMA001-1 COVER: TY-SMA001-2 -0645: 500 PARTS PER TRAY(5 PARTS PER POCKET), -0700, -1000 & -1450: 300 PARTS PER TRAY(3 PARTS PER POCKET) 4. APPLICABLE ON -1450 LENGTH ONLY. F:\DWG\MISC\MKTG\SMP-J-B-XX-ST-XXXX-MKT.SLDDRW UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN MILLIMETERS. TOLERANCES ARE: DECIMALS ANGLES X.X: 0.3 [.01] 5 X.XX: 0.13 [.005] X.XXX: 0.051 [.0020] MATERIAL: PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING PIN, SHELL: BeCu INSULATOR: PTFE SHEET SCALE: 8:1 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail info@SAMTEC.com code 55322 DESCRIPTION: DWG. NO. SMP BULLET - 50 OHM SMP-J-B-XX-ST-XXXX BY: T MEEK 12/3/2010 SHEET 1 OF 2 REVISION B IN-PROCESS 1 INSERT PIN / INSULATOR (1) (-1450 OPTION ONLY) "B" "B" SECTION "B"-"B" PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING SHEET SCALE: 8:1 F:\DWG\MISC\MKTG\SMP-J-B-XX-ST-XXXX-MKT.SLDDRW 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail info@SAMTEC.com code 55322 DESCRIPTION: DWG. NO. SMP BULLET - 50 OHM SMP-J-B-XX-ST-XXXX BY: T MEEK 12/3/2010 SHEET 2 OF 2