FB
LM25085
PGATE
ISEN
GND
VCC
ADJ
4.5V to 42V
Input
VIN
GND
SHUTDOWN
CIN
RT
CVCC
CADJ
RADJ
Q1
D1
L1
Cff COUT
RFB2
RFB1
VOUT
GND
VIN
RT
Product
Folder
Sample &
Buy
Technical
Documents
Tools &
Software
Support &
Community
LM25085
,
LM25085-Q1
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
LM25085 / -Q1 42V Constant On-Time PFET Buck Switching Controller
1 Features 3 Description
The LM25085 is a high efficiency PFET switching
1 LM25085-Q1 is an Automotive Grade product that regulator controller that can be used to quickly and
is AEC-Q100 Grade 1 Qualified (-40°C to 125°C easily develop a small, efficient buck regulator for a
Operating Junction Temperature) wide range of applications. This high voltage
Wide 4.5V to 42V Input Voltage Range controller contains a PFET gate driver and a high
voltage bias regulator which operates over a wide
Adjustable Current Limit Using RDS(ON) or a 4.5V to 42V input range. The constant on-time
Current Sense Resistor regulation principle requires no loop compensation,
Programmable Switching Frequency to 1MHz simplifies circuit implementation, and results in ultra-
No Loop Compensation Required fast load transient response. The operating frequency
Ultra-Fast Transient Response remains nearly constant with line and load variations
due to the inverse relationship between the input
Nearly Constant Operating Frequency with Line voltage and the on-time. The PFET architecture
and Load Variations allows 100% duty cycle operation for a low dropout
Adjustable Output Voltage from 1.25V voltage. Either the RDS(ON) of the PFET or an external
Precision ±2% Feedback Reference sense resistor can be used to sense current for over-
current detection.
Capable of 100% Duty Cycle Operation
Internal Soft-Start Timer Device Information(1)
Integrated High Voltage Bias Regulator PART NUMBER PACKAGE BODY SIZE (NOM)
Thermal Shutdown LM25085-Q1 HVSSOP (8) 3.00 mm x 3.00 mm
VSSOP (8) 3.00 mm x 3.00 mm
2 Applications LM25085 WSON (8) 3.00 mm x 3.00 mm
Automotive Infotainment HVSSOP (8) 3.00 mm x 3.00 mm
Battery/Super Capacitor Chargers (1) For all available packages, see the orderable addendum at
the end of the datasheet.
LED Drivers
Simplified Schematic
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM25085
,
LM25085-Q1
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
www.ti.com
Table of Contents
7.3 Feature Description................................................. 12
1 Features.................................................................. 17.4 Device Functional Modes........................................ 16
2 Applications ........................................................... 18 Application and Implementation ........................ 17
3 Description............................................................. 18.1 Application Information............................................ 17
4 Revision History..................................................... 28.2 Typical Application ................................................. 17
5 Pin Configuration and Functions......................... 39 Power Supply Recommendations...................... 24
6 Specifications......................................................... 410 Layout................................................................... 24
6.1 Absolute Maximum Ratings ..................................... 410.1 Layout Guidelines ................................................. 24
6.2 Handling Ratings - LM25085 .................................... 410.2 Layout Example .................................................... 24
6.3 Handling Ratings - LM25085-Q1 .............................. 411 Device and Documentation Support................. 25
6.4 Recommended Operating Conditions....................... 411.1 Device Support .................................................... 25
6.5 Thermal Information.................................................. 411.2 Related Links ........................................................ 25
6.6 Electrical Characteristics........................................... 511.3 Trademarks........................................................... 25
6.7 Typical Characteristics.............................................. 711.4 Electrostatic Discharge Caution............................ 25
7 Detailed Description............................................ 11 11.5 Glossary................................................................ 25
7.1 Overview................................................................. 11 12 Mechanical, Packaging, and Orderable
7.2 Functional Block Diagram....................................... 11 Information ........................................................... 25
4 Revision History
Changes from Revision I (April 2013) to Revision J Page
Added Device Information and Handling Rating tables, Feature Description, Device Functional Modes, Application
and Implementation, Power Supply Recommendations, Layout, Device and Documentation Support, and
Mechanical, Packaging, and Orderable Information sections; moved some curves to Application Curves section ............. 1
2Submit Documentation Feedback Copyright © 2008–2014, Texas Instruments Incorporated
Product Folder Links: LM25085 LM25085-Q1
1
2
3
4 5
8
7
6
FB PGATE
ISEN
GND
VCC
ADJ
RT
VIN
8
7
6
5
4
3
2
1
Exposed Pad on Bottom
Connect to Ground
FB
GND
ADJ
PGATE
ISEN
VCC
RT
VIN
1
2
3
4 5
8
7
6
Exposed Pad on Bottom
Connect to Ground
FB PGATE
ISEN
GND
VCC
ADJ
RT
VIN
LM25085
,
LM25085-Q1
www.ti.com
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
5 Pin Configuration and Functions
HVSSOP-PowerPad™ WSON
8-Lead DGN0008A 8-Lead NGQ0008A
Top View Top View
VSSOP
8-Lead DGK0008A
Top View
Pin Functions
PIN I/O DESCRIPTION
NAME NO.
Current Limit Adjust - The current limit threshold is set by an external resistor from VIN to ADJ in
ADJ 1 I conjunction with the external sense resistor or the PFET’s RDS(ON).
On-time control and shutdown - An external resistor from VIN to RT sets the buck switch on-time and
RT 2 I switching frequency. Grounding this pin shuts down the controller.
Voltage Feedback from the regulated output - Input to the regulation and over-voltage comparators.
FB 3 I The regulation level is 1.25V.
GND 4 - Circuit Ground - Ground reference for all internal circuitry.
Current sense input for current limit detection. Connect to the PFET drain when using RDS(ON) current
ISEN 5 I sense. Connect to the PFET source and the sense resistor when using a current sense resistor.
PGATE 6 O Gate Driver Output - Connect to the gate of the external PFET.
Output of the gate driver bias regulator - Output of the negative voltage regulator (relative to VIN) that
VCC 7 O biases the PFET gate driver. A low ESR capacitor is required from VIN to VCC, located as close as
possible to the pins.
Input supply voltage - The operating input range is from 4.5V to 42V. A low ESR bypass capacitor
VIN 8 I must be located as close as possible to the VIN and GND pins.
Exposed Pad - Exposed pad on the underside of the package (HVSSOP-PowerPAD-8 and WSON
EP - only). This pad is to be soldered to the PC board ground plane to aid in heat dissipation.
Copyright © 2008–2014, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM25085 LM25085-Q1
LM25085
,
LM25085-Q1
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
See (1) (2) MIN MAX UNIT
VIN to GND -0.3 45 V
ISEN to GND -3 VIN + 0.3 V
ADJ to GND -0.3 VIN + 0.3 V
RT, FB to GND -0.3 7 V
VIN to VCC, VIN to PGATE -0.3 10 V
(1) Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is intended to be functional. For specifications and test conditions, see the Electrical Characteristics.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
6.2 Handling Ratings - LM25085 MIN MAX UNIT
Tstg Storage temperature range -65 150 °C
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all 2 kV
pins(1)
V(ESD) Electrostatic discharge Charged device model (CDM), per JEDEC specification 750 V
JESD22-C101, all pins(2)
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Handling Ratings - LM25085-Q1 MIN MAX UNIT
Tstg Storage temperature range -65 150 °C
Human body model (HBM), per AEC Q100-002(1) 2 kV
V(ESD) Electrostatic discharge Corner pins 1, 4, 5, 8 750
Charged device model (CDM), per V
AEC Q100-011 Other pins 750
(1) AEC Q100-002 indicates HBM stressing is done in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
6.4 Recommended Operating Conditions
Over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT
VIN Voltage 4.5 42 V
Junction Temperature 40 125 °C
6.5 Thermal Information LM25085 LM25085 / LM25085
Q-1
THERMAL METRIC(1) VSSOP HVSSOP- WSON UNIT
PowerPAD
8 PINS 8 PINS 8 PINS
RθJA Junction-to-ambient thermal resistance 153 54.1 44.8
RθJC Junction-to-case (top) thermal resistance 52.5 49.1 39.4
RθJB Junction-to-board thermal resistance 71.9 26.7 11.6 °C/W
ψJT Junction-to-top characterization parameter 4.6 1.3 0.3
ψJB Junction-to-board characterization parameter 70.8 26.5 11.6
RθJC(bot) Junction-to-case (bottom) thermal resistance 29 3.6 5.0
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
4Submit Documentation Feedback Copyright © 2008–2014, Texas Instruments Incorporated
Product Folder Links: LM25085 LM25085-Q1
LM25085
,
LM25085-Q1
www.ti.com
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
6.6 Electrical Characteristics
Typical values correspond to TJ= 25°C. Minimum and maximum limits apply over –40°C to 125°C junction temperature
range, unless otherwise stated. VIN = 24V, RT= 100kunless otherwise stated. (See (1)).
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
VIN PIN
IIN Operating Current Non-Switching, FB = 1.4V (2) 1.25 1.75 mA
IQShutdown Current RT = 0V (2) 175 300 µA
VCC REGULATOR (3)
VCC(reg) VIN - VCC Vin = 9V, FB = 1.4V, ICC = 0mA 6.9 7.7 8.5 V
Vin = 9V, FB = 1.4V, ICC = 20mA 7.7 V
Vin = 42V, FB = 1.4V, ICC = 0mA 7.7 V
UVLOVcc VCC Under-Voltage Lock-Out VCC Increasing 3.8 V
Threshold
UVLOVcc Hysteresis VCC Decreasing 260 mV
VCC(CL) VCC Current Limit FB = 1.4V 20 40 mA
PGATE PIN
VPGATE(HI) PGATE High Voltage PGATE Pin = Open VIN -0.1 VIN V
VPGATE(LO) PGATE Low Voltage PGATE Pin = Open VCC VCC+0.1 V
VPGATE(HI)4.5 PGATE High Voltage at Vin = 4.5V PGATE Pin = Open VIN -0.1 VIN V
VPGATE(LO)4.5 PGATE Low Voltage at Vin = 4.5V PGATE Pin = Open VCC VCC+0.1 V
IPGATE Driver Output Source Current VIN = 12V, PGATE = VIN - 3.5V 1.75 A
Driver Output Sink Current VIN = 12V, PGATE = VIN - 3.5V 1.5 A
RPGATE Driver Output Resistance Source current = 500mA 2.3
Sink current = 500mA 2.3
CURRENT LIMIT DETECTION
IADJ ADJUST Pin Current Source VADJ = 22.5V 32 40 48 µA
VCL OFFSET Current Limit Comparator Offset VADJ = 22.5V, VADJ - VISEN -9 0 9 mV
RT PIN
RTSD Shutdown Threshold RT Pin Voltage Rising 0.73 V
RTHYS Shutdown Threshold Hysteresis 50 mV
ON-TIME
tON 1 On-Time VIN = 4.5V, RT= 100k3.5 5 7.15 µs
tON 2 VIN = 24V, RT= 100k560 720 870 ns
tON - 3 VIN = 42V, RT= 100k329 415 500 ns
tON - 4 Minimum On-Time in Current Limit VIN = 24V, 25mV Overdrive at ISEN 55 140 235 ns
(4)
OFF-TIME
tOFF(CL1) Off-Time (Current Limit) (4) VIN = 12V, VFB = 0V 5.35 7.9 10.84 µs
tOFF(CL2) VIN = 12V, VFB = 1V 1.42 1.9 3.03 µs
tOFF(CL3) VIN = 24V, VFB = 0V 8.9 13 17.7 µs
tOFF(CL4) VIN = 24V, VFB = 1V 2.22 3.2 4.68 µs
REGULATION AND OVER-VOLTAGE COMPARATORS (FB PIN)
VREF FB Regulation Threshold 1.225 1.25 1.275 V
VOV FB Over-Voltage Threshold Measured With Respect to VREF 350 mV
IFB FB Bias Current 10 nA
(1) All hot and cold limits are specified by correlating the electrical characteristics to process and temperature variations and applying
statistical process control.
(2) Operating current and shutdown current do not include the current in the RTresistor.
(3) VCC provides self bias for the internal gate drive.
(4) The tolerance of the minimum on-time (tON-4) and the current limit off-times (tOFF(CL1) through (tOFF(CL4)) track each other over process
and temperature variations. A device which has an on-time at the high end of the range will have an off-time that is at the high end of its
range.
Copyright © 2008–2014, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM25085 LM25085-Q1
LM25085
,
LM25085-Q1
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
www.ti.com
Electrical Characteristics (continued)
Typical values correspond to TJ= 25°C. Minimum and maximum limits apply over –40°C to 125°C junction temperature
range, unless otherwise stated. VIN = 24V, RT= 100kunless otherwise stated. (See (1)).
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
SOFT-START FUNCTION
tSS Soft-Start Time 1.4 2.5 4.3 ms
THERMAL SHUTDOWN
TSD Junction Shutdown Temperature Junction Temperature Rising 170 °C
THYS Junction Shutdown Hysteresis 20 °C
6Submit Documentation Feedback Copyright © 2008–2014, Texas Instruments Incorporated
Product Folder Links: LM25085 LM25085-Q1
LM25085
,
LM25085-Q1
www.ti.com
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
6.7 Typical Characteristics
Unless otherwise specified the following conditions apply: TJ= 25°C, VIN = 24V.
Figure 1. Efficiency (Circuit Of LM25085 Typical Application) Figure 2. Input Operating Current vs. VIN
Figure 3. Shutdown Current vs. VIN Figure 4. VCC vs. VIN
Figure 5. VCC vs. ICC Figure 6. On-Time vs. RTAnd VIN
Copyright © 2008–2014, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM25085 LM25085-Q1
LM25085
,
LM25085-Q1
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified the following conditions apply: TJ= 25°C, VIN = 24V.
Figure 7. Off-Time vs. VIN And VFB Figure 8. Voltage At The Rt Pin
Figure 10. Input Operating Current vs. Temperature
Figure 9. Adj Pin Current vs. VIN
Figure 12. Vcc vs. Temperature
Figure 11. Shutdown Current vs. Temperature
8Submit Documentation Feedback Copyright © 2008–2014, Texas Instruments Incorporated
Product Folder Links: LM25085 LM25085-Q1
LM25085
,
LM25085-Q1
www.ti.com
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
Typical Characteristics (continued)
Unless otherwise specified the following conditions apply: TJ= 25°C, VIN = 24V.
Figure 13. On-Time vs. Temperature Figure 14. Minimum On-Time vs. Temperature
Figure 16. Current Limit Comparator Offset vs. Temperature
Figure 15. Off-Time vs. Temperature
Figure 17. Adj Pin Current vs. Temperature Figure 18. Pgate Driver Output Resistance vs. Temperature
Copyright © 2008–2014, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM25085 LM25085-Q1
LM25085
,
LM25085-Q1
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified the following conditions apply: TJ= 25°C, VIN = 24V.
Figure 19. Feedback Reference Voltage vs. Temperature Figure 20. Soft-Start Time vs. Temperature
Figure 21. Rt Pin Shutdown Threshold vs. Temperature
10 Submit Documentation Feedback Copyright © 2008–2014, Texas Instruments Incorporated
Product Folder Links: LM25085 LM25085-Q1
Duty Cycle = tON
tON + tOFF
== tON x FS
VOUT
VIN
LM25085
,
LM25085-Q1
www.ti.com
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
7 Detailed Description
7.1 Overview
The LM25085 is a PFET buck (step-down) DC-DC controller using the constant on-time (COT) control principle.
The input operating voltage range of the LM25085 is 4.5V to 42V. The use of a PFET in a buck regulator greatly
simplifies the gate drive requirements and allows for 100% duty cycle operation to extend the regulation range
when operating at low input voltage. However, PFET transistors typically have higher on-resistance and gate
charge when compared to similarly rated NFET transistors. Consideration of available PFETs, input voltage
range, gate drive capability of the LM25085, and thermal resistances indicate an upper limit of 10A for the load
current for LM25085 applications. Constant on-time control is implemented using an on-time one-shot that is
triggered by the feedback signal. During the off-time, when the PFET (Q1) is off, the load current is supplied by
the inductor and the output capacitor. As the output voltage falls, the voltage at the feedback comparator input
(FB) falls below the regulation threshold. When this occurs Q1 is turned on for the one-shot period which is
determined by the input voltage (VIN) and the RTresistor. During the on-time the increasing inductor current
increases the voltage at FB above the feedback comparator threshold. For a buck regulator the basic relationship
between the on-time, off-time, input voltage and output voltage is:
where
Fs is the switching frequency (1)
Equation 1 is valid only in continuous conduction mode (inductor current does not reach zero). Since the
LM25085 controls the on-time inversely proportional to VIN, the switching frequency remains relatively constant
as VIN is varied. If the input voltage falls to a level that is equal to or less than the regulated output voltage Q1 is
held on continuously (100% duty cycle) and VOUT is approximately equal to VIN.
The COT control scheme, with the feedback signal applied to a comparator rather than an error amplifier,
requires no loop compensation, resulting in very fast load transient response.
The LM25085 is available in both an 8 pin HVSSOP-PowerPAD package and an 8 pin WSON package with an
exposed pad to aid in heat dissipation. An 8 pin VSSOP package without an exposed pad is also available.
7.2 Functional Block Diagram
Sense resistor method shown for current limit detection.
Minimum output ripple configuration shown.
Copyright © 2008–2014, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM25085 LM25085-Q1
FS = VOUT x (VIN - 1.56V + RT/3167)
VIN x [(1.45 x 10-7 x (RT + 1.4)) + (tD x (VIN - 1.56V + RT/3167))]
tON = (VIN - 1.56V + RT/3167)
1.45 x 10-7 x (RT + 1.4) + 50 ns
LM25085
,
LM25085-Q1
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
www.ti.com
7.3 Feature Description
7.3.1 Regulation Control Circuit
The LM25085 buck DC-DC controller employs a control scheme based on a comparator and a one-shot on-
timer, with the output voltage feedback compared to an internal reference voltage (1.25V). When the FB pin
voltage falls below the feedback reference, Q1 is switched on for a time period determined by the input voltage
and a programming resistor (RT). Following the on-time Q1 remains off until the FB voltage falls below the
reference. Q1 is then switched on for another on-time period. The output voltage is set by the feedback resistors
(RFB1, RFB2 in Functional Block Diagram. The regulated output voltage is calculated as follows:
VOUT = 1.25V x (RFB2+ RFB1)/ RFB1 (2)
The feedback voltage supplied to the FB pin is applied to a comparator rather than a linear amplifier. For proper
operation sufficient ripple amplitude is necessary at the FB pin to switch the comparator at regular intervals with
minimum delay and noise susceptibility. This ripple is normally obtained from the output voltage ripple attenuated
through the feedback resistors. The output voltage ripple is a result of the inductor’s ripple current passing
through the output capacitor’s ESR, or through a resistor in series with the output capacitor. Multiple methods are
available to ensure sufficient ripple is supplied to the FB pin, and three different configurations are discussed in
Alternate Output Ripple Configurations.
When in regulation, the LM25085 operates in continuous conduction mode at medium to heavy load currents and
discontinuous conduction mode at light load currents. In continuous conduction mode the inductor’s current is
always greater than zero, and the operating frequency remains relatively constant with load and line variations.
The minimum load current for continuous conduction mode is one-half the inductor’s ripple current amplitude. In
discontinuous conduction mode, where the inductor’s current reaches zero during the off-time, the operating
frequency is lower than in continuous conduction mode and varies with load current. Conversion efficiency is
maintained at light loads since the switching losses are reduced with the reduction in load and frequency.
If the voltage at the FB pin exceeds 1.6V due to a transient overshoot or excessive ripple at VOUT the internal
over-voltage comparator immediately switches off Q1. The next on-time period starts when the voltage at FB falls
below the feedback reference voltage.
7.3.2 On-Time Timer
The on-time of the PFET gate drive output (PGATE pin) is determined by the resistor (RT) and the input voltage
(VIN), and is calculated from:
where
RTis in k(3)
The minimum on-time, which occurs at maximum VIN, should not be set less than 150ns (see Current Limiting).
The buck regulator effective on-time, measured at the SW node (junction of Q1, L1, and D1) is typically longer
than that calculated in Equation 3 due to the asymmetric delay of the PFET. The on-time difference caused by
the PFET switching delay can be estimated as the difference of the turn-off and turn-on delays listed in the PFET
data sheet. Measuring the difference between the on-time at the PGATE pin versus the SW node in the actual
application circuit is also recommended.
In continuous conduction mode, the inverse relationship of tON with VIN results in a nearly constant switching
frequency as VIN is varied. The operating frequency can be calculated from:
where
RTis in k
tDis equal to 50ns plus the PFET’s delay difference (4)
12 Submit Documentation Feedback Copyright © 2008–2014, Texas Instruments Incorporated
Product Folder Links: LM25085 LM25085-Q1
RT
Input
Voltage
STOP
RUN
LM25085
RT
VIN
RT = VOUT x 6 x 106
FS - 8.6
LM25085
,
LM25085-Q1
www.ti.com
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
Feature Description (continued)
To set a specific continuous conduction mode switching frequency (FS), the RTresistor is determined from the
following:
where
RTis in k(5)
A simplified version of Equation 5 at VIN = 12V, and tD= 100ns, is:
(6)
For VIN = 42V and tD= 100ns, the simplified equation is:
(7)
7.3.3 Shutdown
The LM25085 can be shutdown by grounding the RT pin (see Figure 22). In this mode the PFET is held off, and
the VCC regulator is disabled. The internal operating current is reduced to the value shown in Figure 3. The
shutdown threshold at the RT pin is 0.73V, with 50mV of hysteresis. Releasing the pin enables normal
operation. The RT pin must not be forced high during normal operation.
Figure 22. Shutdown Implementation
7.3.4 Current Limiting
The LM25085 current limiting operates by sensing the voltage across either the RDS(ON) of Q1, or a sense
resistor, during the on-time and comparing it to the voltage across the resistor RADJ (see Figure 23). The current
limit function is much more accurate and stable over temperature when a sense resistor is used. The RDS(ON) of a
MOSFET has a wide process variation and a large temperature coefficient.
If the voltage across RDS(ON) of Q1, or the sense resistor, is greater than the voltage across RADJ, the current limit
comparator switches to turn off Q1. Current sensing is disabled for a blanking time of 100ns at the beginning of
the on-time to prevent false triggering of the current limit comparator due to leading edge current spikes.
Because of the blanking time and the turn-on and turn-off delays created by the PFET, the on-time at the PGATE
pin should not be set less than 150ns. An on-time shorter than that may prevent the current limit detection circuit
from properly detecting an over-current condition. The duration of the subsequent forced off-time is a function of
the input voltage and the voltage at the FB pin, as shown in Figure 7. The longer-than-normal forced off-time
allows the inductor current to decrease to a low level before the next on-time. This cycle-by-cycle monitoring,
followed by a forced off-time, provides effective protection from output load faults over a wide range of operating
conditions.
The voltage across the RADJ resistor is set by an internal 40µA current sink at the ADJ pin. When using Q1’s
RDS(ON) for sensing, the current at which the current limit comparator switches is calculated from:
ICL = 40µA x RADJ/RDS(ON) (8)
Copyright © 2008–2014, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM25085 LM25085-Q1
VIN x tON
tOFF
VFD + VESR t
'I = (VOUT + VFD + VESR) x tOFF
L
'I = (VIN - VOUT) x tON
L
LM25085
,
LM25085-Q1
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
www.ti.com
Feature Description (continued)
When using a sense resistor (RSEN) the threshold of the current limit comparator is calculated from:
ICL = 40µA x RADJ/RSEN (9)
When using Equation 8 or Equation 9, the tolerances for the ADJ pin current sink and the offset of the current
limit comparator should be included to ensure the resulting minimum current limit is not less than the required
maximum switch current. Simultaneously increasing the values of RADJ and RSEN decreases the effects of the
current limit comparator offset, but at the expense of higher power dissipation. When using a sense resistor, the
RSEN resistor value should be chosen within the practical limitations of power dissipation and physical size. For
example, for a 10A current limit, setting RSEN = 0.005results in a power dissipation as high as 0.5W. Current
sense connections to the RSEN resistor, or to Q1, must be Kelvin connections to ensure accuracy.
The CADJ capacitor filters noise from the ADJ pin, and helps prevent unintended switching of the current limit
comparator due to input voltage transients. The recommended value for CADJ is 1000pF.
7.3.5 Current Limit Off-Time
When the current through Q1 exceeds the current limit threshold, the LM25085 forces an off-time longer than the
normal off-time defined by Equation 1. See Figure 7 or calculate the current limit off-time from the following
equation:
where
VIN is the input voltage
VFB is the voltage at the FB pin at the time current limit was detected (10)
This feature is necessary to allow the inductor current to decrease sufficiently to offset the current increase which
occurred during the on-time. During the on-time, the inductor current increases an amount equal to:
(11)
During the off-time the inductor current decreases due to the reverse voltage applied across the inductor by the
output voltage, the freewheeling diode’s forward voltage (VFD), and the voltage drop due to the inductor’s series
resistance (VESR). The current decrease is equal to:
(12)
The on-time in Equation 11 is shorter than the normal on-time since the PFET is shut off when the current limit
threshold is crossed. If the off-time is not long enough, such that the current decrease (Equation 12) is less than
the current increase (Equation 11), the current levels are higher at the start of the next on-time. This results in a
further decrease in on-time, since the current limit threshold is crossed sooner. A balance is reached when the
current changes in Equation 11 and Equation 12 are equal. The worst case situation is that of a direct short
circuit at the output terminals, where VOUT = 0V, as that results in the largest current increase during the on-time,
and the smallest decrease during the off-time. The sum of the diode’s forward voltage and the inductor’s ESR
voltage must be sufficient to ensure current runaway does not occur. Using Equation 11 and Equation 12, this
requirement can be stated as:
(13)
14 Submit Documentation Feedback Copyright © 2008–2014, Texas Instruments Incorporated
Product Folder Links: LM25085 LM25085-Q1
LM25085
PGATE
ISEN
VCC
ADJ
CADJ
RADJ
Q1
D1
L1
LM25085
CURRENT LIMIT
COMPARATOR
GATE
DRIVER
40 PAADJ RADJ
CADJ
40 PA
Q1 L1
D1
GATE
DRIVER
CURRENT LIMIT
COMPARATOR
ISEN
PGATE
VCC
RSEN
+
-+
-
USING Q1 RDS(ON) USING SENSE RESISTOR RSEN
VIN
VIN
VIN VIN
LM25085
,
LM25085-Q1
www.ti.com
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
Feature Description (continued)
For tON in Equation 13 use the minimum on-time at the SW node. To determine this time period add the
“Minimum on-time in current limit” specified in Electrical Characteristics (tON-4) to the difference of the turn-off
and turn-on delays of the PFET. For tOFF use the value in Figure 7 or use Equation 10, where VFB is equal to
zero volts. When using the minimum or maximum limits of those specifications to determine worst case
situations, the tolerance of the minimum on-time (tON-4) and the current limit off-times (tOFF(CL1) through tOFF(CL4))
track each other over the process and temperature variations. A device which has an on-time at the high end of
the range will have an off-time that is at the high end of its range.
Figure 23. Current Limit Sensing
7.3.6 VCC Regulator
The VCC regulator provides a regulated voltage between the VIN and the VCC pins to provide the bias and gate
current for the PFET gate driver. The 0.47µF capacitor at the VCC pin must be a low ESR capacitor, preferably
ceramic as it provides the high surge current for the PFET’s gate at each turn-on. The capacitor must be located
as close as possible to the VIN and VCC pins to minimize inductance in the PC board traces.
Referring to Figure 4, the voltage across the VCC regulator (VIN VCC) is equal to VIN until VIN reaches
approximately 8.5V. At higher values of VIN, the voltage at the VCC pin is regulated at approximately 7.7V below
VIN. If VIN drops below about 8V due to voltage transients, the VCC pin can be pulled down below GND. To
prevent the negative VCC voltage from disturbing the internal circuit and causing abnormal operation, a Schottky
diode is recommended between VCC pin and GND pin. The VCC regulator has a maximum current capability of
at least 20mA. The regulator is disabled when the LM25085 is shutdown using the RT pin, or when the thermal
shutdown is activated.
7.3.7 PGATE Driver Output
The PGATE pin output swings between VIN (Q1 off) and the VCC pin voltage (Q1 on). The rise and fall times
depend on the PFET gate capacitance and the source and sink currents provided by the internal gate driver. See
Electrical Characteristics for the current capability of the driver.
7.3.8 P-Channel MOSFET Selection
The PFET must be rated for the maximum input voltage, with some margin above that to allow for transients and
ringing which can occur on the supply line and the switching node. The gate-to-source voltage (VGS) normally
provided to the PFET is 7.7V for VIN greater than 8.5V. However, if the circuit is to be operated at lower values
of VIN, the selected PFET must be able to fully turn-on with a VGS voltage equal to VIN. The minimum input
operating voltage for the LM25085 is 4.5V.
Copyright © 2008–2014, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM25085 LM25085-Q1
LM25085
,
LM25085-Q1
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
www.ti.com
Feature Description (continued)
Similar to NFETs, the case or exposed thermal pad for a PFET is electrically connected to the drain terminal.
When designing a PFET buck regulator the drain terminal is connected to the switching node. This situation
requires a trade-off between thermal and EMI performance since increasing the PC board area of the switching
node to aid the PFET power dissipation also increases radiated noise, possibly disrupting the circuit operation.
Typically the switching node area is kept to a reasonable minimum and the PFET peak current is derated to stay
within the recommended temperature rating of the PFET. The RDS(ON) of the PFET determines a portion of the
power dissipation in the PFET. However, PFETs with very low RDS(ON) usually have large values of gate charge.
A PFET with a higher gate charge has a corresponding slower switching speed, leading to higher switching
losses and affecting the PFET power dissipation.
If the PFET RDS(ON) is used for current limit detection, note that it typically has a positive temperature coefficient.
At 100°C the RDS(ON) may be as much as 50% higher than the value at 25°C which could result in incorrect
current limiting if not accounted for when determining the value of the RADJ resistor. The PFET Total Gate
Charge determines most of the power dissipation in the LM25085 due to the repetitive charge and discharge of
the PFET’s gate capacitance by the gate driver (powered from the VCC regulator). The LM25085’s internal
power dissipation can be calculated from the following:
PDISS = VIN x ((QGx FS)+IIN)
where
QGis the PFET Total Gate Charge obtained from its datasheet
FSis the switching frequency
IIN is the LM25085's operating current obtained from Figure 2 (14)
Using the Thermal Resistance specifications in Electrical Characteristics, the approximate junction temperature
can be determined. If the calculated junction temperature is near the maximum operating temperature of 125°C,
either the switching frequency must be reduced, or a PFET with a smaller Total Gate Charge must be used.
7.3.9 Soft-Start
The internal soft-start feature of the LM25085 allows the regulator to gradually reach a steady state operating
point at power up, thereby reducing startup stresses and current surges. Upon turn-on, when VCC reaches its
under-voltage lockout threshold, the internal soft-start circuit ramps the feedback reference voltage from 0V to
1.25V, causing VOUT to ramp up in a proportional manner. The soft-start ramp time is typically 2.5ms.
In addition to controlling the initial power up cycle, the soft-start circuit also activates when the LM25085 is
enabled by releasing the RT pin, and when the circuit is shutdown and restarted by the internal Thermal
Shutdown circuit.
If the voltage at FB is below the regulation threshold value due to an over-current condition or a short circuit at
VOUT, the internal reference voltage provided by the soft-start circuit to the regulation comparator is reduced
along with FB. When the over-current or short circuit condition is removed, VOUT returns to the regulated value at
a rate determined by the soft-start ramp. This feature helps prevent the output voltage from overshooting
following an overload event.
7.3.10 Thermal Shutdown
The LM25085 should be operated such that the junction temperature does not exceed 125°C. If the junction
temperature increases above that, an internal Thermal Shutdown circuit activates at 170°C (typical) to disable
the VCC regulator and the gate driver, and discharge the soft-start capacitor. This feature helps prevent
catastrophic failures from accidental device overheating. When the junction temperature falls below 150°C
(typical hysteresis = 20°C), the gate driver is enabled, the soft-start circuit is released, and normal operation
resumes.
7.4 Device Functional Modes
7.4.1 Standby Mode with VIN <4.5 V
The LM25085 is intended to operate with input voltages above 4.5 V. The minimum operating input voltage is
determined by the VCC undervoltage lockout threshold of 3.8 V (typ). If VIN is too low to support a VCC voltage
greater than the VCC UVLO threshhold, the controller switches to the standby mode with the PFET buck switch
in the off state.
16 Submit Documentation Feedback Copyright © 2008–2014, Texas Instruments Incorporated
Product Folder Links: LM25085 LM25085-Q1
7V to 42V
Input
VIN
GND
SHUTDOWN
CIN
33 PF
CBYP
1 PF
RT
90.9 k:
GND FB
PGATE
ISEN
ADJ
VCC
CVCC
0.47 PF
CADJ 1000 pF
RADJ
2.1 k:
RSEN
0.01:
L1 15 PH
Q1
D1
VOUT
COUT
GND
C1
3300 pF
C2
0.1 PF
R3
66.5 k:
5V
100 PF
RFB1
3.4 k:
RFB2
10 k:
RT
VIN
LM25085
LM25085
,
LM25085-Q1
www.ti.com
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
Device Functional Modes (continued)
7.4.2 RT Shutdown Mode
The LM25085 is in shutdown mode when the RT pin is pulled below 0.73 V (typ). In this mode the PFET gate
driver is held off, and the VCC regulator is disabled.
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LM25085/LM25085-Q1 devices are step-down DC-DC converters. The devices are typically used to convert
a higher DC voltage to a lower DC voltage. Use the following design procedure to select component values.
Alternately, use the WEBENCH®software to generate a complete design. The WEBENCH software uses an
iterative design procedure and accesses a comprehensive database of components when generating a design.
This section presents a simplified discussion of the design process.
8.2 Typical Application
Figure 24. LM25085 Typical Application
8.2.1 Design Requirements
The procedure for calculating the external components is illustrated with the following design example. Referring
to Figure 24, the circuit is to be configured for the following specifications:
VOUT = 5V
VIN = 7V to 42V, 12V Nominal
Maximum load current (IOUT(max)) = 5A
Minimum load current (IOUT(min)) = 600mA (for continuous conduction mode)
Switching Frequency (FSW) = 300kHz
Maximum allowable output ripple (VOS) = 5mVp-p
Selected PFET: Vishay Si7465
Copyright © 2008–2014, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM25085 LM25085-Q1
SW Node
IPK
Inductor Current
IOUT
IOR
1/FS
L1 = tON(min) x (VIN(max) - VOUT)
IOR(max) = 13.5 PH
RT = 5 x (12 - 1.56V)
1.45 x 10-7 x 12 x 300 kHz - 1.4= 90.9
(50 ns + 57 ns) x (12 - 1.56V)
1.45 x 10-7
-
LM25085
,
LM25085-Q1
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
www.ti.com
Typical Application (continued)
8.2.2 Detailed Design Procedure
8.2.2.1 RFB1 and RFB2
These resistors set the output voltage. The ratio of these resistors is calculated from:
RFB2/RFB1 = (VOUT/1.25V) - 1 (15)
For this example, RFB2 / RFB1 = 3. Typically, RFB1 and RFB2 should be chosen from standard value resistors in the
range of 1kto 20kwhich satisfy the above ratio. For this example, RFB2 = 10k, and RFB1 = 3.4k.
8.2.2.2 RT, PFET
Before selecting the RTresistor, the PFET must be selected as its turn-on and turn-off delays affect the
calculated value of RT. For the Vishay Si7465 PFET, the difference of its typical turn-off and turn-on delays is
57ns. Using Equation 5 at nominal input voltage, RTcalculates to be:
(16)
A standard value 90.9kresistor is selected. Using Equation 3 the minimum on-time at the PGATE pin, which
occurs at maximum input voltage (42V), is calculated to be 381ns. This minimum one-shot period is sufficiently
longer than the minimum recommended value of 150ns. The minimum on-time at the SW node (junction of Q1,
D1, L1) is longer due to the delay added by the PFET (57ns). Therefore the minimum SW node on-time is 438ns
at 42V. The maximum on-time at the SW node is calculated to be 2.55µs at 7V.
8.2.2.3 L1
The main parameter controlled by the inductor value is the current ripple amplitude (IOR). See Figure 25. The
minimum load current for continuous conduction mode is used to determine the maximum allowable ripple such
that the inductor current valley does not fall to zero. Continuous conduction mode operation at minimum load
current is not a requirement of the LM25085, but serves as a guideline for selecting L1. For this example, the
maximum ripple current is:
IOR(max) = 2 x IOUT(min) = 1.2 Amp (17)
If the minimum load current of the application is zero, a good initial estimate for the maximum ripple current
(IOR(max)) is 20% of the maximum load current. The ripple calculated in Equation 17 is then used in the following
equation to calculate L1:
(18)
A standard value 15µH inductor is selected. Using this inductance value, the maximum ripple current amplitude,
which occurs at maximum input voltage, is calculated to be 1.08 Ap-p. The peak current (IPK) at maximum load
current is 5.54A. However, the current rating of the selected inductor must be based on the maximum current
limit value calculated below.
Figure 25. Inductor Current Waveform
18 Submit Documentation Feedback Copyright © 2008–2014, Texas Instruments Incorporated
Product Folder Links: LM25085 LM25085-Q1
COUT = 1.08A
8 x 300 kHz x 0.005V = 90 PF
COUT = IOR(max)
8 x FS x VRIPPLE
ICL(min) = 0.01:
(2.1 k: x 32 PA) - 9 mV = 5.82A
ICL(max) = 0.01:
(2.1 k: x 48 PA) + 9 mV = 11A
ICL(nom) = 0.01:
(2.1 k: x 40 PA) = 8.4A
RADJ = 32 PA
6.44A x 0.01: = 2.01 k:
LM25085
,
LM25085-Q1
www.ti.com
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
Typical Application (continued)
8.2.2.4 RSEN, RADJ
To achieve good current limit accuracy and avoid over designing the power stage components, the sense
resistor method is used for current limiting in this example. A standard value 10mresistor is selected for RSEN,
resulting in a 50mV drop at maximum load current, and a maximum 0.25W power dissipation in the resistor.
Since the LM25085 uses peak current detection, the minimum value for the current limit threshold must be equal
to the maximum load current (5A) plus half the maximum ripple amplitude calculated above:
ICL(min) = 5A + 1.08A/2 = 5.54A (19)
At this current level the voltage across RSEN is 55.4mV. Adding the current limit comparator offset of 9mV (max)
increases the required current limit threshold to 6.44A. Using Equation 9 with the minimum value for the ADJ pin
current (32µA), the required RADJ resistor is calculated to be:
(20)
A standard value 2.1kresistor is selected. The nominal current limit threshold is:
(21)
Using the tolerances for the ADJ pin current and the current limit comparator offset, the maximum current limit
threshold is calculated to be:
(22)
The minimum current limit threshold is:
(23)
The load current in each case is equal to the current limit threshold minus half the current ripple amplitude. The
recommended value of 1000pF for CADJ is used in this example.
8.2.2.5 COUT
Since the maximum allowed output ripple voltage is very low in this example (5mVp-p), the minimum ripple
configuration (R3, C1, and C2 in the Functional Block Diagram) must be used. The resulting ripple at VOUT is
then due to the inductor’s ripple current passing through COUT. This capacitor’s value can be selected based on
the maximum allowable ripple voltage at VOUT, or based on transient response requirements. The following
calculation, based on ripple voltage, provides a first order result for the value of COUT:
(24)
where IOR(max) is the maximum ripple current calculated above, and VRIPPLE is the allowable ripple at VOUT.
(25)
A 100µF capacitor is selected. Typically the ripple amplitude will be higher than the calculations indicate due to
the capacitor’s ESR.
8.2.2.6 R3, C1, C2
The minimum ripple configuration uses these three components to generate the ripple voltage required at the FB
pin since there is insufficient ripple at VOUT. A minimum of 25mVp-p must be applied to the FB pin to obtain
stable constant frequency operation. R3 and C1 are selected to generate a sawtooth waveform at their junction,
and that waveform is AC coupled to the FB pin via C2. The values of the three components are determined using
the following procedure:
Copyright © 2008–2014, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM25085 LM25085-Q1
Cff = 3 x tON(max)
(RFB1//RFB2)
R4 = 25 mV
IOR(min)
R3 x C1 = (7V - 4.81V) x 2.55 Ps
0.025V = 2.23 x 10-4
R3 x C1 = (VIN(min) - VA) x tON
'V
LM25085
,
LM25085-Q1
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
www.ti.com
Typical Application (continued)
First calculate VA= VOUT - (VSW x (1 (VOUT/VIN(min))))
where VSW is the absolute value of the voltage at the SW node during the off-time, typically 0.5V to 1V
depending on the diode D1. Using a typical value of 0.65V, VAcalculates to 4.81V. VAis the nominal DC voltage
at the R3/C1 junction, and is used in the next equation to calculate the R-C product:
(26)
where tON is the maximum on-time (at minimum input voltage), and ΔV is the desired ripple amplitude at the
R3/C1 junction. For ripple voltage of 25 mVp-p:
(27)
R3 and C1 are then selected from standard value components to produce the product calculated above. Typical
values for C1 are 3000pF to 10,000pF, and R3 is typically from 10kto 300k. C2 is then chosen large
compared to C1, typically 0.1µF. For this example, 3300pF is chosen for C1, requiring R3 to be 67.7k. A
standard value 66.5kresistor is selected.
8.2.2.7 Alternate Output Ripple Configurations
The minimum ripple configuration with C1, C2 and R3 in the example circuit, Figure 24, results in a low ripple
amplitude at VOUT determined mainly by the characteristics of the output capacitor and the ripple current in L1.
This configuration allows multiple ceramic capacitors to be used for VOUT if the output voltage is provided to
several places on the PC board. However, if a slightly higher level of ripple at VOUT is acceptable in the
application, and distributed capacitance is not used, the ripple required for the FB comparator pin can be
generated with fewer external components using the circuits shown in Figure 26 and Figure 27.
8.2.2.7.1 Reduced Ripple Configuration
In Figure 26, R3, C1 and C2 are removed (compared to Layout Example). A low value resistor (R4) is added in
series with COUT, and a capacitor (Cff) is added across RFB2. Ripple is generated at VOUT by the inductor’s ripple
current flowing through R4, and that ripple voltage is passed to the FB pin via Cff. The ripple at VOUT can be set
as low as 25mVp-p since it is not attenuated by RFB2 and RFB1. The minimum value for R4 is calculated from:
(28)
where IOR(min) is the minimum ripple current, which occurs at minimum input voltage. The minimum value for Cff
is determined from:
(29)
where tON(max) is the maximum on-time, which occurs at minimum VIN. The next larger standard value capacitor
should be used for Cff.
20 Submit Documentation Feedback Copyright © 2008–2014, Texas Instruments Incorporated
Product Folder Links: LM25085 LM25085-Q1
FB
LM25085
PGATE
GND
Q1 L1
COUT
RFB2
RFB1
VOUT
GND
D1 R4
R4 = VRIP(min)
IOR(min)
FB
LM25085
PGATE
GND
Q1 L1
Cff
COUT
RFB2
RFB1
VOUT
GND
D1 R4
LM25085
,
LM25085-Q1
www.ti.com
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
Typical Application (continued)
Figure 26. Reduced Ripple Configuration
8.2.2.7.2 Lowest Cost Configuration
This configuration, shown in Figure 27, is the same as Figure 26 except Cff is removed. Since the ripple voltage
at VOUT is attenuated by RFB2 and RFB1, the minimum ripple required at VOUT is equal to:
VRIP(min) = 25mV x (RFB2 + RFB1)/RFB1
The minimum value for R4 is calculated from:
(30)
where IOR(min) is the minimum ripple current, which occurs at minimum input voltage.
Figure 27. Lowest Cost Ripple Generating Configuration
8.2.2.8 CIN, CBYP
These capacitors limit the voltage ripple at VIN by supplying most of the switch current during the on-time. At
maximum load current, when Q1 is switched on, the current through Q1 suddenly increases to the lower peak of
the inductor’s ripple current, then ramps up to the upper peak, and then drops to zero at turn-off. The average
current during the on-time is the load current. For a worst case calculation, these capacitors must supply this
average load current during the maximum on-time, while limiting the voltage drop at VIN. For this example, 0.5V
is selected as the maximum allowable droop at VIN.
Copyright © 2008–2014, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LM25085 LM25085-Q1
CIN + CBYP = IOUT(max) x tON(max)
'V= 25.5 PF
5A x 2.55 Ps
0.5V
=
LM25085
,
LM25085-Q1
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
www.ti.com
Typical Application (continued)
The minimum input capacitance is calculated from:
(31)
A 33µF electrolytic capacitor is selected for CIN, and a 1µF ceramic capacitor is selected for CBYP. Due to the
ESR of CIN, the ripple at VIN will likely be higher than the calculation indicates, and therefore it may be desirable
to increase CIN to 47µF or 68µF. CBYP must be located as close as possible to the VIN and GND pins of the
LM25085. The voltage rating for both capacitors must be at least 42V. The RMS ripple current rating for the input
capacitors must also be considered. A good approximation for the required ripple current rating is IRMS > IOUT/2.
8.2.2.9 D1
A Schottky diode is recommended. Ultra-fast recovery diodes are not recommended as the high speed
transitions at the SW node may affect the regulator’s operation due to diode reverse recovery transients. The
diode must be rated for the maximum input voltage, and the worst case current limit level. The average power
dissipation in the diode is calculated from:
PD1 = VFx IOUT x (1-D) (32)
where VFis the diode forward voltage drop, and D is the on-time duty cycle. Using Equation 1, the minimum duty
cycle occurs at maximum input voltage, and is calculated to be 11.9% in this example. The diode power
dissipation calculates to be:
PD1 = 0.65V x 5A x (1- 0.119) = 2.86W (33)
8.2.2.10 CVCC
The capacitor at the VCC pin (from VIN to VCC) provides not only noise filtering and stability for the VCC
regulator, but also provides the surge current for the PFET gate drive. The typical recommended value for CVCC
is 0.47µF. A good quality, low ESR, ceramic capacitor is recommended. CVCC must be located as close as
possible to the VIN and VCC pins. If the selected PFET has a Total Gate Charge specification of 100nC or
larger, or if the circuit is required to operate at input voltages below 7V, a larger capacitor may be required. The
maximum recommended value for CVCC is 1µF.
8.2.2.11 IC Power Dissipation
The maximum power dissipated in the LM25085 package is calculated using Equation 14 at the maximum input
voltage. The Total Gate Charge for the Si7465 PFET is specified to be 40nC (max) in the data sheet. Therefore
the total power dissipation within the LM25085 is calculated to be:
PDISS = 42V x ((40nC x 300kHz) + 1.3mA) = 559mW (34)
Using an HVSSOP-PowerPAD-8 package with a θJA of 46°C/W produces a temperature rise of 26°C from
junction to ambient.
22 Submit Documentation Feedback Copyright © 2008–2014, Texas Instruments Incorporated
Product Folder Links: LM25085 LM25085-Q1
LM25085
,
LM25085-Q1
www.ti.com
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
Typical Application (continued)
8.2.3 Application Curves
Figure 28. Efficiency vs. Load Current and VIN Figure 29. Frequency vs. VIN
Figure 30. Current Limit vs. VIN (Circuit Of Figure 32) Figure 31. LM25085 Power Dissipation (Circuit Of
Figure 32)
Copyright © 2008–2014, Texas Instruments Incorporated Submit Documentation Feedback 23
Product Folder Links: LM25085 LM25085-Q1
1
2
3
4 5
8
7
6
Exposed Pad on Bottom
Connect to Ground
FB PGATE
ISEN
GND
VCC
ADJ
RT
VIN
RSEN
RT and ADJ
Connections
(Tap to CIN)
CIN
CVCC
L1
COUT
D1
VIN
GND
RFB1
Keep
CIN, D1, Q1
Loop Small
Q1
VOUT
LM25085
,
LM25085-Q1
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
www.ti.com
9 Power Supply Recommendations
The devices are designed to operate from an input voltage supply range between 4.5 V and 42 V. This input
supply must be well regulated. If the input supply is located more than a few inches from the device, additional
bulk capacitance may be required at the input terminals of the converter in addition to the calculated values to
limit the inductive spikes due to the input cables or wires.
10 Layout
10.1 Layout Guidelines
In most applications, the heat sink pad or tab of Q1 is connected to the switch node, i.e. the junction of Q1, L1
and D1. While it is common to extend the PC board pad from under these devices to aid in heat dissipation, the
pad size should be limited to minimize EMI radiation from this switching node. If the PC board layout allows, a
similarly sized copper pad can be placed on the underside of the PC board, and connected with as many vias as
possible to aid in heat dissipation.
The voltage regulation, over-voltage, and current limit comparators are very fast and can respond to short
duration noise pulses. Layout considerations are therefore critical for optimum performance. The layout must be
as neat and compact as possible with all the components as close as possible to their associated pins. Two
major current loops conduct currents which switch very fast, requiring the loops to be as small as possible to
minimize conducted and radiated EMI. The first loop is that formed by CIN, Q1, L1, COUT, and back to CIN. The
second loop is that formed by D1, L1, COUT, and back to D1. The connection from the anode of D1 to the ground
end of CIN must be short and direct. CIN must be as close as possible to the VIN and GND pins, and CVCC must
be as close as possible to the VIN and VCC pins.
If the anticipated internal power dissipation of the LM25085 will produce excessive junction temperatures during
normal operation, a package option with an exposed pad must be used (HVSSOP-PowerPAD-8 or WSON-8).
Effective use of the PC board ground plane can help dissipate heat. Additionally, the use of wide PC board
traces, where possible, helps conduct heat away from the IC. Judicious positioning of the PC board within the
end product, along with the use of any available air flow (forced or natural convection) also helps reduce the
junction temperature.
10.2 Layout Example
Figure 32. LM25085 Buck Converter Layout Example
24 Submit Documentation Feedback Copyright © 2008–2014, Texas Instruments Incorporated
Product Folder Links: LM25085 LM25085-Q1
LM25085
,
LM25085-Q1
www.ti.com
SNVS593J OCTOBER 2008REVISED NOVEMBER 2014
11 Device and Documentation Support
11.1 Device Support
11.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
11.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 1. Related Links
TECHNICAL TOOLS & SUPPORT &
PARTS PRODUCT FOLDER SAMPLE & BUY DOCUMENTS SOFTWARE COMMUNITY
LM25085 Click here Click here Click here Click here Click here
LM25085-Q1 Click here Click here Click here Click here Click here
11.3 Trademarks
PowerPad is a trademark of Texas Instruments.
WEBENCH is a registered trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.5 Glossary
SLYZ022 TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2008–2014, Texas Instruments Incorporated Submit Documentation Feedback 25
Product Folder Links: LM25085 LM25085-Q1
PACKAGE OPTION ADDENDUM
www.ti.com 20-Jan-2017
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM25085MM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SVZB
LM25085MME/NOPB ACTIVE VSSOP DGK 8 250 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SVZB
LM25085MMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SVZB
LM25085MY/NOPB ACTIVE MSOP-
PowerPAD DGN 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SVYB
LM25085MYE/NOPB ACTIVE MSOP-
PowerPAD DGN 8 250 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SVYB
LM25085MYX/NOPB ACTIVE MSOP-
PowerPAD DGN 8 3500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SVYB
LM25085QMY/NOPB ACTIVE MSOP-
PowerPAD DGN 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SYLB
LM25085QMYE/NOPB ACTIVE MSOP-
PowerPAD DGN 8 250 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SYLB
LM25085QMYX/NOPB ACTIVE MSOP-
PowerPAD DGN 8 3500 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SYLB
LM25085SD/NOPB ACTIVE WSON NGQ 8 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L246B
LM25085SDE/NOPB ACTIVE WSON NGQ 8 250 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L246B
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
PACKAGE OPTION ADDENDUM
www.ti.com 20-Jan-2017
Addendum-Page 2
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LM25085, LM25085-Q1 :
Catalog: LM25085
Automotive: LM25085-Q1
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM25085MM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM25085MME/NOPB VSSOP DGK 8 250 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM25085MMX/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM25085MY/NOPB MSOP-
Power
PAD
DGN 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM25085MYE/NOPB MSOP-
Power
PAD
DGN 8 250 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM25085MYX/NOPB MSOP-
Power
PAD
DGN 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM25085QMY/NOPB MSOP-
Power
PAD
DGN 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM25085QMYE/NOPB MSOP-
Power
PAD
DGN 8 250 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM25085QMYX/NOPB MSOP-
Power
PAD
DGN 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
LM25085SD/NOPB WSON NGQ 8 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 2-Sep-2015
Pack Materials-Page 1
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM25085SDE/NOPB WSON NGQ 8 250 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM25085MM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0
LM25085MME/NOPB VSSOP DGK 8 250 210.0 185.0 35.0
LM25085MMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0
LM25085MY/NOPB MSOP-PowerPAD DGN 8 1000 210.0 185.0 35.0
LM25085MYE/NOPB MSOP-PowerPAD DGN 8 250 210.0 185.0 35.0
LM25085MYX/NOPB MSOP-PowerPAD DGN 8 3500 367.0 367.0 35.0
LM25085QMY/NOPB MSOP-PowerPAD DGN 8 1000 210.0 185.0 35.0
LM25085QMYE/NOPB MSOP-PowerPAD DGN 8 250 210.0 185.0 35.0
LM25085QMYX/NOPB MSOP-PowerPAD DGN 8 3500 367.0 367.0 35.0
LM25085SD/NOPB WSON NGQ 8 1000 210.0 185.0 35.0
LM25085SDE/NOPB WSON NGQ 8 250 210.0 185.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 2-Sep-2015
Pack Materials-Page 2
MECHANICAL DATA
DGN0008A
www.ti.com
MUY08A (Rev A)
BOTTOM VIEW
www.ti.com
PACKAGE OUTLINE
C
8X 0.3
0.2
2 0.1
8X 0.5
0.3
2X
1.5
1.6 0.1
6X 0.5
0.8
0.7
0.05
0.00
B3.1
2.9 A
3.1
2.9
(0.1) TYP
WSON - 0.8 mm max heightNGQ0008A
PLASTIC SMALL OUTLINE - NO LEAD
4214922/A 03/2018
PIN 1 INDEX AREA
SEATING PLANE
0.08 C
1
45
8
PIN 1 ID 0.1 C A B
0.05 C
THERMAL PAD
EXPOSED
9
SYMM
SYMM
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
SCALE 4.000
www.ti.com
EXAMPLE BOARD LAYOUT
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
(1.6)
6X (0.5)
(2.8)
8X (0.25)
8X (0.6)
(2)
(R0.05) TYP ( 0.2) VIA
TYP
(0.75)
WSON - 0.8 mm max heightNGQ0008A
PLASTIC SMALL OUTLINE - NO LEAD
4214922/A 03/2018
SYMM
1
45
8
SYMM
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:20X
9
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown
on this view. It is recommended that vias under paste be filled, plugged or tented.
SOLDER MASK
OPENING
SOLDER MASK
METAL UNDER
SOLDER MASK
DEFINED
EXPOSED METAL
METAL
SOLDER MASK
OPENING
SOLDER MASK DETAILS
NON SOLDER MASK
DEFINED
(PREFERRED)
EXPOSED METAL
www.ti.com
EXAMPLE STENCIL DESIGN
8X (0.25)
8X (0.6)
6X (0.5)
(1.79)
(1.47)
(2.8)
(R0.05) TYP
WSON - 0.8 mm max heightNGQ0008A
PLASTIC SMALL OUTLINE - NO LEAD
4214922/A 03/2018
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
SOLDER PASTE EXAMPLE
BASED ON 0.1 mm THICK STENCIL
EXPOSED PAD 9:
82% PRINTED SOLDER COVERAGE BY AREA UNDER PACKAGE
SCALE:20X
SYMM
1
45
8
SYMM
METAL
TYP
9
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
LM25085QMY/NOPB LM25085QMYE/NOPB LM25085QMYX/NOPB