MAX3221/MAX3223/MAX3243 +3V to +5.5V RS-232 Transceivers with AutoShutdown General Description Benefits and Features The MAX3221/MAX3223/MAX3243 achieve 1A supply current with Maxim's revolutionary AutoShutdownTM feature. When the MAX3221/MAX3223/MAX3243 do not sense a valid signal level on their receiver inputs, the on-board power supply and drivers shut down. This occurs if the RS-232 cable is disconnected or if the transmitters of the connected peripheral are turned off. The system turns on again when a valid level is applied to any RS-232 receiver input. The MAX3221/MAX3223/MAX3243 require only 0.1F capacitors in 3.3V operation, and can operate from input voltages ranging from +3.0V to +5.5V. A proprietary, high-efficiency, dual charge-pump power supply and a low-dropout transmitter combine to deliver true RS-232 performance from a single +3.0V to +5.5V supply. * Integrated Charge Pump Circuitry Simplifies Power The MAX3221 is a 1-driver/1-receiver 16-pin SSOP version of the 20-pin 2-driver/2-receiver MAX3223. The MAX3243 is a 3-driver/5-receiver with a complementary always-active receiver for external monitoring in a variety of 28 pin packages. Please see order information table for package offerings. Applications * * * * Battery-Powered Equipment Hand-Held Equipment Peripherals Portable Diagnostics Equipment Selector Guide PART Tx Rx VCC RANGE (V) AutoShutdown MAX3221 1 1 3.0 to 5.5 Yes MAX3223 2 2 3.0 to 5.5 Yes MAX3243 3 5 3.0 to 5.5 Yes Pin Configurations appear at end of data sheet. Typical Operating Circuits appear at end of data sheet. AutoShutdown and UCSP are trademarks of Maxim Integrated Products, Inc. 19-0306; Rev 9; 1/15 Requirements * Eliminates the Need for a 12 Supply * Operation From a Single +3.3V or +5V Supply * 1A Supply Current in Shutdown Mode Saves Power * AutoShutdown Feature is Enabled After No Activity on Receiver Inputs for 30s * Software Control Option for Shutdown Ordering Information PART MAX3221CAE MAX3221CUE TEMP RANGE PIN-PACKAGE 0C to +70C 16 SSOP 0C to +70C 16 TSSOP MAX3221EAE -40C to +85C 16 SSOP MAX3221EUE -40C to +85C 16 TSSOP MAX3223CPP 0C to +70C 20 Plastic DIP MAX3223CAP 0C to +70C 20 SSOP MAX3223CUP 0C to +70C 20 TSSOP MAX3223EPP -40C to +85C 20 Plastic DIP MAX3223EAP -40C to +85C 20 SSOP MAX3223EUP -40C to +85C 20 TSSOP MAX3243CWI 0C to +70C 28 Wide SO MAX3243CAI 0C to +70C 28 SSOP MAX3243CUI 0C to +70C 28 TSSOP MAX3243EWI -40C to +85C 28 Wide SO MAX3243EAI -40C to +85C 28 SSOP MAX3243EUI -40C to +85C 28 TSSOP Future product--contact factory for availability. +3V to +5.5V RS-232 Transceivers with AutoShutdown MAX3221/MAX3223/MAX3243 Absolute Maximum Ratings 16-Pin SSOP (derate 7.14mW/C above +70C) ...........571mW 16-Pin TSSOP (derate 6.70mW/C above +70C) .........533mW 20-Pin Plastic DIP (derate 11.11mW/C above +70C)....889mW 20-Pin SSOP (derate 8.00mW/C above +70C) ...........640mW 20-Pin TSSOP DIP (derate 7.00mW/C above +70C).....559mW 28-Pin Wide SO (derate 12.50mW/C above +70C) ............1W 28-Pin SSOP (derate 9.52mW/C above +70C) ...........762mW 28-Pin TSSOP (derate 8.70mW/C above +70C) .........696mW Operating Temperature Ranges MAX32_ _C_ _.......................................................0C to +70C MAX32_ _E_ _ ....................................................-40C to +85C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) .................................+300C VCC ...........................................................................-0.3V to +6V V+ (Note 1) ...............................................................-0.3V to +7V V- (Note 1) ...............................................................+0.3V to -7V V+ + |V-| (Note 1).................................................................+13V Input Voltages T_IN, FORCEOFF, FORCEON, EN (MAX3223) ......-0.3V to +6V R_IN ...................................................................................25V Output Voltages T_OUT.............................................................................13.2V R_OUT, INVALID ......................................-0.3V to (VCC + 0.3V) Short-Circuit Duration T_OUT ......................................................................Continuous Continuous Power Dissipation (TA = +70C) Note 1: V+ and V- can have maximum magnitudes of 7V, but their absolute difference cannot exceed 13V. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Electrical Characteristics (VCC = +3.0V to +5.5V, C1-C4 = 0.1F (Note 2), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER CONDITIONS MIN TYP MAX UNITS 1.0 10 A 1.0 10 A 0.3 1.0 mA 0.8 V DC CHARACTERISTICS Supply Current, AutoShutdown Supply Current, Shutdown Supply Current, AutoShutdown Disabled All R_IN open, FORCEON = GND, VCC = 3.3V FORCEOFF = VCC or 5.0V, FORCEOFF = GND TA = +25C FORCEON = FORCEOFF = V , CC no load LOGIC INPUTS AND RECEIVER OUTPUTS Input Logic Threshold Low T_IN, FORCEON, FORCEOFF, EN (MAX3223) VCC = 3.3V 2.0 VCC = 5.0V 2.4 Input Logic Threshold High T_IN, EN, FORCEON, FORCEOFF Input Leakage Current T_IN, EN, FORCEON, FORCEOFF 0.01 1.0 A Output Leakage Current Receivers disabled 0.05 10 A Output Voltage Low IOUT = 1.6mA 0.4 V Output Voltage High IOUT = -1.0mA VCC - 0.6 V VCC - 0.1 V AUTOSHUTDOWN (FORCEON = GND, FORCEOFF = VCC) Positive threshold Receiver Input Thresholds to Transmitters Enabled Figure 5 Receiver Input Thresholds to Transmitters Disabled 1A supply current, Figure 5 INVALID Output Voltage Low IOUT = 1.6mA INVALID Output Voltage High IOUT = -1.0mA Receiver Threshold to Transmitters Enabled (tWU) Receiver Positive or Negative Threshold to INVALID High (tINVH) Receiver Positive or Negative Threshold to INVALID Low (tINVL) www.maximintegrated.com Negative threshold 2.7 -2.7 -0.3 VCC - 0.6 V 0.3 V 0.4 V V Figure 5 250 s Figure 5 1 s Figure 5 30 s Maxim Integrated | 2 +3V to +5.5V RS-232 Transceivers with AutoShutdown MAX3221/MAX3223/MAX3243 Electrical Characteristics (continued) (VCC = +3.0V to +5.5V, C1-C4 = 0.1F (Note 2), TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER CONDITIONS MIN TYP MAX UNITS 25 V RECEIVER INPUTS Input Voltage Range -25 Input Threshold Low TA = +25C Input Threshold High TA = +25C VCC = 3.3V 0.6 1.2 VCC = 5.0V 0.8 1.5 VCC = 3.3V 1.5 2.4 VCC = 5.0V 1.8 2.4 Input Hysteresis Input Resistance V 0.3 TA = +25C 3 5 V V 7 k TRANSMITTER OUTPUTS Output Voltage Swing All transmitter outputs loaded with 3k to ground 5.0 5.4 V Output Resistance VCC = V+ = V- = 0V, transmitter output = 2V 300 10M Output Short-Circuit Current Output Leakage Current 35 VOUT = 12V, VCC = 0V or 3.0V to 5.5V, transmitters disabled 60 mA 25 A MOUSE DRIVEABILITY (MAX3243) Transmitter Output Voltage T1IN = T2IN = GND, T3IN = VCC, T3OUT loaded with 3k to GND, T1OUT and T2OUT loaded with 2.5mA each 5 RL = 3k, CL = 1000pF, one transmitter switching 120 V TIMING CHARACTERISTICS Maximum Data Rate 235 tPHL 0.3 tPLH 0.3 kbps Receiver Propagation Delay Receiver input to receiver output, CL = 150pF Receiver Output Enable Time Normal operation 200 ns Receiver Output Disable Time Normal operation 200 ns Transmitter Skew tPHL - tPLH MAX3221/MAX3223 200 MAX3243 200 tPHL - tPLH MAX3221/MAX3223 100 MAX3243 100 500 8.0 30 Receiver Skew Transition-Region Slew Rate VCC = 3.3V, RL = 3k to 7k, TA = +25C, measured from +3V to -3V or -3V to +3V CL = 200pF to 2500pF 4 CL = 200pF to 1000pF 6 s 1000 ns ns V/s 30 Note 2: C1-C4 = 0.1F, tested at 3.3V 10%. C1 = 0.047F, C2-C4 = 0.33F, tested at 5.0V 10%. www.maximintegrated.com Maxim Integrated | 3 +3V to +5.5V RS-232 Transceivers with AutoShutdown MAX3221/MAX3223/MAX3243 Typical Operating Characteristics (VCC = +3.3V, 235kbps data rate, 0.1F capacitors, all transmitters loaded with 3k, TA = +25C, unless otherwise noted.) 18 0 -1 -2 -3 16 CU -SLEW 12 10 +SLEW 8 6 -4 4 VOUT- 35 35 30 235kbps 30 14 3 3 SU 2 1 -5 FOR DATA RATES UP TO 235kbps 25 25 20 120kbps 20 15 15 10 20kbps 10 5 2 0 1000 2000 3000 4000 0 150 500 1000 5000 LOAD CAPACITANCE (pF) 5 2000 3000 4000 5.0 24 22 1 TRANSMITTER AT 235kbps 2 TRANSMITTERS AT 30kbps 0 -2.5 18 -SLEW 16 14 12 +SLEW 10 VOUT- -5.0 ALL OUTPUTS LOADED WITH 3k +CL 0.1F CHARGE-PUMP CAPACITORS FOR ALL DATA RATES UP TO 235kbps 6 4 0 1000 2000 3000 4000 LOAD CAPACITANCE (pF) www.maximintegrated.com 5000 5000 235kbps 35 30 120kbps 25 20 20kbps 15 10 8 -7.5 4000 40 SUPPLY CURRENT (mA) SLEW RATE (V/s) 20 3000 45 MAX3221/3223-05 VOUT+ 2000 MAX3243 SUPPLY CURRENT vs. LOAD CAPACITANCE WHEN TRANSMITTING DATA MAX3243 SLEW RATE vs. LOAD CAPACITANCE MAX3221/3223-04 7.5 1000 LOAD CAPACITANCE (pF) LOAD CAPACITANCE (pF) MAX3243 TRANSMITTER OUTPUT VOLTAGE vs. LOAD CAPACITANCE 2.5 0 0 5000 MAX3221/3223-06 -6 TRANSMITTER OUTPUT VOLTAGE (V) ) MAX3221/3223-02 20 MAX3221/3223-03 40 ( 4 3 22 MAX3221/3223-01 VOUT+ SLEW RATE (V/s) TRANSMITTER OUTPUT VOLTAGE (V) 6 5 MAX3221/MAX3223 SUPPLY CURRENT vs. LOAD CAPACITANCE WHEN TRANSMITTING DATA MAX3221/MAX3223 SLEW RATE vs. LOAD CAPACITANCE MAX3221 SUPPLY CURRENT (mA) MAX3221/MAX3223 TRANSMITTER OUTPUT VOLTAGE vs. LOAD CAPACITANCE 0 1000 2000 3000 4000 LOAD CAPACITANCE (pF) 5 0 5000 0 1000 2000 3000 4000 5000 LOAD CAPACITANCE (pF) Maxim Integrated | 4 +3V to +5.5V RS-232 Transceivers with AutoShutdown MAX3221/MAX3223/MAX3243 Pin Description PIN NAME FUNCTION -- EN Receiver Enable Control. Drive low for normal operation. Drive high to force the receiver outputs into a high-Z state. 5 1 C2+ Positive terminal of inverting charge-pump capacitor 6 6 2 C2- Negative terminal of inverting charge-pump capacitor 7 7 3 V- 8 9, 16 4-8 R_IN 13 8, 17 9, 10, 11 T_OUT 11 12, 13 12, 13, 14 T_IN TTL/CMOS Transmitter Inputs 9 10, 15 15-19 R_OUT TTL/CMOS Receiver Outputs -- -- 20 R2OUTB Noninverting Receiver Output--active in shutdown 10 11 21 INVALID Output of the valid signal detector. Indicates if a valid RS-232 level is present on receiver inputs logic "1". 16 20 22 FORCEOFF Drive low to shut down transmitters and on-board power supply. This overrides all automatic circuitry and FORCEON (Table 1). 12 14 23 FORCEON Drive high to override automatic circuitry keeping transmitters on (FORCEOFF must be high) (Table 1). 4 4 24 C1- Negative terminal of the voltage doubler charge-pump capacitor 14 18 25 GND Ground 15 19 26 VCC +3.0V to +5.5V Supply Voltage 3 3 27 V+ +5.5V generated by the charge pump 2 2 28 C1+ MAX3221 MAX3223 MAX3243 1 1 5 -5.5V generated by the charge pump RS-232 Receiver Inputs RS-232 Transmitter Outputs Positive terminal of the voltage doubler charge-pump capacitor Detailed Description Dual Charge-Pump Voltage Converter The MAX3221/MAX3223/MAX3243's internal power supply consists of a regulated dual charge pump that provides output voltages of +5.5V (doubling charge pump) and -5.5V (inverting charge pump), regardless of the input voltage (V CC) over the +3.0V to +5.5V range. The charge pumps operate in a discontinuous mode: if the output voltages are less than 5.5V, the charge pumps are enabled; if the output voltages exceed 5.5V, the charge pumps are disabled. Each charge pump requires a flying capacitor (C1, C2) and a reservoir capacitor (C3, C4) to generate the V+ and V- supplies. RS-232 Transmitters The transmitters are inverting level translators that convert CMOS-logic levels to 5.0V EIA/TIA-232 levels. They guarantee a 120kbps data rate with worst-case loads of 3k in parallel with 1000pF, providing compatibility with PC-to-PC communication software (such as LaplinkTM). Typically, the MAX3221/MAX3223/MAX3243 can operate at data rates of 235kbps. Transmitters can be paralleled to drive multiple receivers or mice (MAX3243). Figure 1 shows a complete system connection. When FORCEOFF is driven to ground, or the AutoShutdown circuitry senses invalid voltage levels at all receiver inputs, the transmitters are disabled and the outputs are forced into a high-impedance state. LapLink is a trademark of Traveling Software. www.maximintegrated.com Maxim Integrated | 5 +3V to +5.5V RS-232 Transceivers with AutoShutdown MAX3221/MAX3223/MAX3243 POWER MANAGEMENT UNIT OR KEYBOARD CONTROLLER VCC FORCEOFF FORCEON INVALID PROTECTION DIODE PREVIOUS RS-232 MAX3243 VCC I Rx 5k UART Tx CPU I/O CHIP WITH UART GND SHDN = GND RS-232 (a) OLDER RS-232: POWERED-DOWN UART DRAWS CURRENT FROM ACTIVE RECEIVER OUTPUT IN SHUTDOWN. VCC TO P LOGIC TRANSITION DETECTOR Figure 1. Interface Under Control of PMU I PROTECTION DIODE RS-232 Receivers The MAX3221/MAX3223/MAX3243's receivers convert RS-232 signals to CMOS-logic output levels. All receivers have one inverting three-state output. In shutdown (FORCEOFF = low) or in AutoShutdown, the MAX3221/MAX3223's receivers are active (Table 1). Driving EN high places the receiver(s) in a high-impedance state. The MAX3243's receivers are high impedance when the part is shut down. The MAX3243 has an always-active complementary output (R2OUTB). R2OUTB is an extra output that monitors receiver activity while the other receivers are high impedance. This allows Ring Indicator to be monitored without forward biasing other devices connected to the receiver outputs. This is ideal for systems where VCC is set to 0V in shutdown to accommodate peripherals, such as UARTs (Figure 2). www.maximintegrated.com MAX3243 R2OUTB VCC Rx THREE-STATED UART 5k Tx GND (b) R2IN R2OUT T1OUT T1IN FORCEOFF = GND NEW MAX3243: IN SHUTDOWN, R2OUTB IS USED TO MONITOR EXTERNAL DEVICES AND R2OUT IS THREE STATED, ELIMINATING A CURRENT PATH THROUGH THE UART'S PROTECTION DIODE. Figure 2. The MAX3243 detects RS-232 activity when the UART and interface are shut down. Maxim Integrated | 6 MAX3221/MAX3223/MAX3243 Table 1a. MAX3221/MAX3223 FORCEOFF and Enable Control Truth Table FORCEOFF EN T_OUT R_OUT 0 0 High-Z Active 0 1 High-Z High-Z 1 0 Active* Active 1 1 Active* High-Z +3V to +5.5V RS-232 Transceivers with AutoShutdown +0.3V R_IN 30s COUNTER R -0.3V TO MAX32_ _ POWER SUPPLY AND TRANSMITTERS INVALID * TRANSMITTERS ARE DISABLED, REDUCING SUPPLY CURRENT TO 1A IF ALL RECEIVER INPUTS ARE BETWEEN +0.3V AND -0.3V FOR AT LEAST 30s. Figure 3a. MAX32_ _ Entering 1A Supply Mode via AutoShutdown Table 1b. MAX3243 FORCEOFF Control Truth Table FORCEOFF T_OUT R_OUT R2OUTB 0 High-Z High-Z Active 1 Active* Active* Active *Note: If the part is in AutoShutdown mode (FORCEOFF = VCC, FORCEON = GND), it is shut down if no valid RS-232 levels are present on all receiver inputs. AutoShutdown A 1A supply current is achieved with Maxim's new AutoShutdown feature, which operates when FORCEON is low and FORCEOFF is high. When the MAX3221/MAX3223/MAX3243 sense no valid signal levels on all receiver inputs for 30s, the on-board power supply and drivers are shut off, reducing supply current to 1A. This occurs if the RS-232 cable is disconnected or the connected peripheral transmitters are turned off. The system turns on again when a valid level is applied to any RS-232 receiver input. As a result, the system saves power without changes to the existing BIOS or operating system. When using AutoShutdown, the INVALID output is high when the device is on and low when the device is shut down. Because INVALID indicates the receiver inputs' condition, it can be used in any mode (Figure 3). Table 2 and Figure 3c summarize the MAX3221/ MAX3223/MAX3243 operating modes. FORCEON and FORCEOFF override the automatic circuitry and force the transceiver into its normal operating state or into its low-power standby state. When neither control is asserted, the IC selects between these states automatically based on receiver input levels. Figures 3a, 3b, and 5a depict valid and invalid RS-232 receiver levels. A mouse or other system with AutoShutdown may need time to wake up. Figure 4 shows a circuit that forces the transmitters on for 100ms, allowing enough time for the other system to realize that the MAX3221/MAX3223/ www.maximintegrated.com +2.7V R_IN 30s COUNTER R -2.7V TO MAX32_ _ POWER SUPPLY INVALID * TRANSMITTERS ARE ENABLED IF: ANY RECEIVER INPUT IS GREATER THAN +2.7V OR LESS THAN -2.7V. ANY RECEIVER INPUT HAS BEEN BETWEEN +0.3V AND -0.3V FOR LESS THAN 30s. Figure 3b. MAX32_ _ with Transmitters Enabled Using AutoShutdown FORCEOFF POWER DOWN FORCEON INVALID INVALID IS AN INTERNALLY GENERATED SIGNAL THAT IS USED BY THE AUTOSHUTDOWN LOGIC AND APPEARS AS AN OUTPUT OF THE DEVICE. POWER DOWN IS ONLY AN INTERNAL SIGNAL. IT CONTROLS THE OPERATIONAL STATUS OF THE TRANSMITTERS AND THE POWER SUPPLIES. Figure 3c. AutoShutdown Logic POWER MANAGEMENT UNIT MASTER SHDN LINE 0.1F 1M FORCEOFF FORCEON MAX3221 MAX3223 MAX3243 Figure 4. AutoShutdown with Initial Turn-On to Wake Up a Mouse or Another System Maxim Integrated | 7 MAX3221/MAX3223/MAX3243 +3V to +5.5V RS-232 Transceivers with AutoShutdown Table 2. AutoShutdown Logic RS-232 SIGNAL PRESENT AT RECEIVER INPUT FORCEOFF INPUT FORCEON INPUT INVALID OUTPUT Yes H X H Normal Operation No H H L Normal Operation (Forced On) No H L L Shutdown (AutoShutdown) Yes L X H Shutdown (Forced Off) No L X L Shutdown (Forced Off) Software-Controlled Shutdown If direct software control is desired, INVALID can be used to indicate DTR or Ring Indicator signal. Tie FORCEOFF and FORCEON together to bypass AutoShutdown so the line acts like a SHDN input. TRANSMITTERS ENABLED, INVALID HIGH RECEIVER INPUT LEVELS MAX3243 is awake. If the other system outputs valid RS-232 signals within that time, the RS-232 ports on both systems remain enabled. When shut down, the device's charge pumps are turned off, V+ decays to VCC, V- decays to ground, and the transmitter outputs are disabled (high impedance). The time required to exit shutdown is typically 100s (Figure 5b). TRANSCEIVER STATUS +2.7V INDETERMINATE +0.3V 0V AUTOSHUTDOWN, TRANSMITTERS DISABLED, 1A SUPPLY CURRENT, INVALID LOW -0.3V INDETERMINATE -2.7V TRANSMITTERS ENABLED, INVALID HIGH (a) Applications Information Capacitor Selection The capacitor type used for C1-C4 is not critical for proper operation; either polarized or nonpolarized capacitors may be used. The charge pump requires 0.1F capacitors for 3.3V operation. For other supply voltages, refer to Table 3 for required capacitor values. Do not use values smaller than those listed in Table 3. Increasing the capacitor values (e.g., by a factor of 2) reduces ripple on the transmitter outputs and slightly reduces power consumption. C2, C3, and C4 can be increased without changing C1's value. However, do not increase C1 without also increasing the values of C2, C3, and C4 to maintain the proper ratios (C1 to the other capacitors). When using the minimum required capacitor values, make sure the capacitor value does not degrade excessively with temperature. If in doubt, use capacitors with a larger nominal value. The capacitor's equivalent series resistance (ESR) usually rises at low temperatures and influences the amount of ripple on V+ and V-. www.maximintegrated.com RECEIVER INPUT VOLTAGE (V) INVALID REGION VCC INVALID OUTPUT (V) 0 tINVL tINVH tWU V+ VCC 0 V- (b) Figure 5. AutoShutdown Trip Levels Maxim Integrated | 8 MAX322 +3V to +5.5V RS-232 Transceivers with AutoShutdown MAX3221/MAX3223/MAX3243 5V/div T2 2V/div T1 TRANSMITTER OUTPUT VOLTAGE (V) 5 4 3 VOUT+ VCC = 3.0V 2 1 T1 0 -1 T2 VOUT+ -2 -3 VCC VOUT- T3 VOUT- -4 -5 -6 0 50s/div 1 2 3 4 5 6 7 LOAD CURRENT PER TRANSMITTER (mA) VCC = +3.3V C1-C4 = 0.1F Figure 6. Transmitter Outputs when Exiting Shutdown or Powering Up Figure 7a. MAX3243 Transmitter Output Voltage vs. Load Current per Transmitter Power-Supply Decoupling mice and met their respective current and voltage requirements. Figure 7a shows the transmitter outputs under increasing load current. The MAX3243's switching regulator ensures the transmitters will supply at least 5V during worst-case conditions. The AutoShutdown feature does not work with a mouse, so FORCEOFF and FORCEON should be connected to VCC. In most circumstances a 0.1F bypass capacitor is adequate. In applications that are sensitive to powersupply noise, decouple VCC to ground with a capacitor of the same value as the charge-pump capacitor C1. Connect bypass capacitors as close to the IC as possible. Transmitter Outputs when Exiting Shutdown High Data Rates Figure 6 shows two transmitter outputs when exiting shutdown mode. As they become active, the two transmitter outputs are shown going to opposite RS-232 levels. Each transmitter is loaded with 3k in parallel with 2500pF. The transmitter outputs display no ringing or undesirable transients as they come out of shutdown. Note that the transmitters are enabled only when the magnitude of V- exceeds approximately 3V. Figure 7a shows the MAX3243's transmitter output voltage vs. current per transmitter. Figure 7b is a mouse driver test circuit. The MAX3221/MAX3223/MAX3243 maintain the RS-232 5.0V minimum transmitter output voltage even at high data rates. Figure 8 shows a transmitter loopback test circuit. Figure 9 shows a loopback test result at 120kbps, and Figure 10 shows the same test at 235kbps. For Figure 9, all three transmitters were driven simultaneously at 120kbps into RS-232 loads in parallel with 1000pF. For Figure 10, a single transmitter was driven at 235kbps, but all three transmitters were loaded with an RS-232 receiver in parallel with 1000pF. Mouse Driveability (MAX3243) The MAX3221/MAX3223/MAX3243 can directly interface with various 5V logic families, including ACT and HCT CMOS. See Table 4 for more information on possible combinations of interconnections. The MAX3243 has been specifically designed to power serial mice while operating from low-voltage power supplies. It has been tested with samples of ten major mouse models from six manufacturers including the leading three: Logitech (5 models), Mouse Systems, and Microsoft. The MAX3243 successfully drove all serial www.maximintegrated.com Interconnection with 3V and 5V Logic Maxim Integrated | 9 +3V to +5.5V RS-232 Transceivers with AutoShutdown MAX3221/MAX3223/MAX3243 +3.3V 26 0.1F 28 C1 0.1F 24 1 C2 0.1F 2 LOGIC INPUTS VCC 27 C1+ C1- V+ C3 0.1F MAX3243 COMPUTER SERIAL PORT 3 C2+ V- C4 0.1F C2- 14 T1IN T1OUT 9 +V 13 T2IN T2OUT 10 +V 12 T3IN T3OUT 11 -V 20 R2OUTB 19 R1OUT GND R1IN 4 R2IN 5 R3IN 6 R4IN 7 R5IN 8 Tx 5k 18 R2OUT LOGIC OUTPUTS 5k 17 R3OUT RS-232 INPUTS 5k 16 R4OUT 5k 15 23 VCC TO POWER MANAGEMENT UNIT 22 21 R5OUT SERIAL MOUSE 5k FORCEON FORCEOFF INVALID GND 25 Figure 7b. Mouse Driver Test Circuit www.maximintegrated.com Maxim Integrated | 10 MAX3221/MAX3223/MAX3243 +3V to +5.5V RS-232 Transceivers with AutoShutdown Table 3. Required Capacitor Values VCC 0.1F VCC C1+ V+ C3 C1 C1C2+ MAX3221 MAX3223 MAX3243 VC4 C2 C2- T_ OUT T_ IN R_ IN R_ OUT 0V VCC EN (MAX3221/3) FORCEOFF 5k VCC (V) C1 (F) C2, C3, C4 (F) 3.0 to 3.6 0.1 0.1 4.5 to 5.5 0.047 0.33 3.0 to 5.5 0.1 0.47 Table 4. Logic Family Compatibility with Various Supply Voltages SYSTEM POWERSUPPLY VOLTAGE (V) VCC SUPPLY VOLTAGE (V) 3.3 3.3 5 5 5 3.3 1000pF GND COMPATIBILITY Compatible with all CMOS families. Compatible with all TTL and CMOS-logic families. Compatible with ACT and HCT CMOS, and with TTL. Incompatible with AC, HC, or CD4000 CMOS. Figure 8. Loopback Test Circuit T1IN 5V/div T1IN 5V/div T1OUT 5V/div T1OUT 5V/div R1OUT 5V/div R1OUT 5V/div 5s/div VCC = +3.3V, 120kbps C1-C4 = 0.1F Figure 9. Loopback Test Result at 120kbps www.maximintegrated.com 2s/div VCC = +3.3V, 235kbps C1-C4 = 0.1F Figure 10. Loopback Test Result at 235kbps Maxim Integrated | 11 MAX3221/MAX3223/MAX3243 +3V to +5.5V RS-232 Transceivers with AutoShutdown Typical Operating Circuits +3.3V 15 0.1F C5 2 C1+ C1 0.1F 4 C15 C2 0.1F 6 VCC 3 V+ MAX3221 C2+ V- C3 0.1F C4 0.1F T1OUT 13 28 C1+ C1 0.1F C2 0.1F R1IN 8 2 5k 1 EN 12 INVALID 10 FORCEOFF 16 FORCEON GND TO POWER MANAGEMENT UNIT VCC 27 V+ C3 0.1F 24 C11 9 R1OUT 26 0.1F 7 C2- 11 T1IN +3.3V LOGIC INPUTS C2+ MAX3243 V- 3 C4 0.1F C2- 14 T1IN T1OUT 9 13 T2IN T2OUT 10 12 T3IN T3OUT 11 RS-232 OUTPUTS VCC 20 R2OUTB 14 19 R1OUT R1IN 4 5k +3.3V C5 C1 0.1F 0.1F 2 C1+ 4 C15 C2 0.1F 19 6 MAX3223 C2+ R2IN 3 V+ V- C3 0.1F LOGIC OUTPUTS 17 R3OUT R3IN 6 16 R4OUT R4IN 7 5k RS-232 OUTPUTS T2OUT 8 15 R5OUT 23 R1IN 16 15 R1OUT TTL/CMOS OUTPUTS VCC RS-232 INPUTS 5k R2IN 9 10 R2OUT RS-232 INPUTS 5k C4 0.1F T1OUT 17 12 T2IN 5 5k 7 C2- 13 T1IN TTL/CMOS INPUTS 18 R2OUT VCC TO POWER MANAGEMENT UNIT 22 R5IN 8 5k FORCEON FORCEOFF 21 INVALID GND 25 5k 1 EN 14 INVALID 11 FORCEOFF 20 FORCEON GND TO POWER MANAGEMENT UNIT VCC 18 www.maximintegrated.com Maxim Integrated | 12 +3V to +5.5V RS-232 Transceivers with AutoShutdown MAX3221/MAX3223/MAX3243 3V-Powered EIA/TIA-232 and EIA/TIA-562 Transceivers from Maxim PART POWERSUPPLY VOLTAGE (V) No. OF TRANSMITTERS/ RECEIVERS No. OF RECEIVERS ACTIVE IN SHUTDOWN GUARANTEED DATA RATE (kbps) EIA/TIA232 OR 562 MAX212 3.0 to 3.6 3/5 5 120 232 Drives mice MAX218 1.8 to 4.25 2/2 2 120 232 Operates directly from batteries without a voltage regulator MAX562 MAX563 2.7 to 5.25 3.0 to 3.6 3/5 2/2 5 2 230 120 562 562 230kbps guaranteed data rate 0.1F capacitors MAX3212 2.7 to 3.6 3/5 5 235 232 AutoShutdown, complementary receiver, drives mice, transient detection MAX3221 MAX3222 MAX3223 MAX3232 3.0 to 5.5 3.0 to 5.5 3.0 to 5.5 3.0 to 5.5 1/1 2/2 2/2 2/2 1 2 2 N/A 120 120 120 120 232 232 232 232 0.1F capacitors, 16-pin SSOP 0.1F capacitors, MAX242 pinout 0.1F capacitors, AutoShutdown 0.1F capacitors, MAX232 pinout MAX3241 3.0 to 5.5 3/5 5 120 232 0.1F capacitors, 2 complementary receivers, drives mice MAX3243 3.0 to 5.5 3/5 1 120 232 0.1F capacitors, AutoShutdown complementary receiver, drives mice www.maximintegrated.com FEATURES Maxim Integrated | 13 +3V to +5.5V RS-232 Transceivers with AutoShutdown MAX3221/MAX3223/MAX3243 Pin Configurations TOP VIEW EN 1 16 FORCEOFF EN 1 C1+ 2 15 VCC V+ 3 14 GND MAX3221 C1- 4 13 T1OUT 12 FORCEON C2- 6 11 T1IN V+ 3 18 GND C2+ 5 C2- 6 V- 7 10 INVALID 9 R1OUT R1IN 8 19 VCC C1- 4 C2+ 5 V- 7 20 FORCEOFF C1+ 2 16 R1IN 15 R1OUT 14 FORCEON T2OUT 8 13 T1IN R2IN 9 12 T2IN R2OUT 10 SSOP/TSSOP 17 T1OUT MAX3223 11 INVALID DIP/SSOP/TSSOP C2+ 1 28 C1+ C2- 2 27 V+ V- 3 26 VCC R1IN 4 25 GND R2IN 5 24 C1- R3IN 6 23 FORCEON MAX3243 R4IN 7 22 FORCEOFF R5IN 8 21 INVALID T1OUT 9 20 R2OUTB T2OUT 10 19 R1OUT T3OUT 11 18 R2OUT T3IN 12 17 R3OUT T2IN 13 16 R4OUT T1IN 14 15 R5OUT SO/SSOP/TSSOP www.maximintegrated.com Maxim Integrated | 14 +3V to +5.5V RS-232 Transceivers with AutoShutdown MAX3221/MAX3223/MAX3243 Package Information 2 SSOP.EPS For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. 1 INCHES E H MILLIMETERS MIN MAX MIN MAX A 0.068 0.078 1.73 1.99 A1 0.002 0.008 0.05 0.21 B 0.010 0.015 0.25 0.38 C D 0.09 0.20 0.004 0.008 SEE VARIATIONS E 0.205 DIM e 0.212 0.0256 BSC 5.20 INCHES D D D D D 5.38 MILLIMETERS MIN MAX MIN MAX 0.239 0.239 0.278 0.249 0.249 0.289 6.07 6.07 7.07 6.33 6.33 7.33 0.317 0.397 0.328 0.407 8.07 10.07 8.33 10.33 N 14L 16L 20L 24L 28L 0.65 BSC H 0.301 0.311 7.65 7.90 L 0.025 0 0.037 8 0.63 0 0.95 8 N A C B e A1 L D PROPRIETARY INFORMATION TITLE: PACKAGE OUTLINE, SSOP, 5.3 MM APPROVAL DOCUMENT CONTROL NO. 21-0056 REV. C 1 1 TSSOP4.40mm.EPS NOTES: 1. D&E DO NOT INCLUDE MOLD FLASH. 2. MOLD FLASH OR PROTRUSIONS NOT TO EXCEED .15 MM (.006"). 3. CONTROLLING DIMENSION: MILLIMETERS. 4. MEETS JEDEC MO150. 5. LEADS TO BE COPLANAR WITHIN 0.10 MM. www.maximintegrated.com Maxim Integrated | 15 +3V to +5.5V RS-232 Transceivers with AutoShutdown MAX3221/MAX3223/MAX3243 Package Information (continued) INCHES N E DIM A A1 B C e E H L H MAX MIN 0.093 0.104 0.004 0.012 0.014 0.019 0.009 0.013 0.050 0.291 0.299 0.394 0.419 0.050 0.016 SOICW.EPS For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. MILLIMETERS MIN 2.35 0.10 0.35 0.23 MAX 2.65 0.30 0.49 0.32 1.27 7.40 7.60 10.00 10.65 0.40 1.27 VARIATIONS: 1 INCHES TOP VIEW DIM D D D D D D A B e FRONT VIEW MIN 0.398 0.447 0.496 0.598 0.697 MAX 0.413 0.463 0.512 0.614 0.713 MILLIMETERS MIN 10.10 11.35 12.60 15.20 17.70 MAX 10.50 11.75 13.00 15.60 18.10 N MS013 16 AA 18 AB 20 AC 24 AD 28 AE C 0-8 A1 L SIDE VIEW PROPRIETARY INFORMATION TITLE: PACKAGE OUTLINE, .300" SOIC DOCUMENT CONTROL NO. 21-0042 REV. B 1 1 PDIPN.EPS APPROVAL www.maximintegrated.com Maxim Integrated | 16 MAX3221/MAX3223/MAX3243 +3V to +5.5V RS-232 Transceivers with AutoShutdown Revision History REVISION NUMBER REVISION DATE 9 1/15 DESCRIPTION Updated General Description and Benefits and Features sections PAGES CHANGED 1 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated's website at www.maximintegrated.com. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. (c) 2015 Maxim Integrated Products, Inc. | 17