Sample & Buy Product Folder Support & Community Tools & Software Technical Documents LP38859 SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 LP38859 3-A Fast-Response High-Accuracy LDO Linear Regulator With Soft Start 1 Features 3 Description * * * * * The LP38859 is a high-current, fast-response regulator which can maintain output voltage regulation with extremely low input to output voltage drop. Fabricated on a CMOS process, the device operates from two input voltages: VBIAS provides voltage to drive the gate of the N-MOS power transistor, while VIN is the input voltage which supplies power to the load. The use of an external bias rail allows the part to operate from ultra-low VIN voltages. Unlike bipolar regulators, the CMOS architecture consumes extremely low quiescent current at any output load current. The use of an NMOS power transistor results in wide bandwidth, yet minimum external capacitance is required to maintain loop stability. 1 * * * * Input Voltage: 1.1 V to 5.5 V Wide VBIAS Supply Operating Range: 3 V to 5.5 V Standard VOUT Values: 0.8 V and 1.2 V Stable With 10-F Ceramic Capacitors Dropout Voltage of 240 mV (typical) at 3-A Load Current Programmable Soft-Start Time Precision Output Voltage Across All Line and Load Conditions: - 1% VOUT for TJ = 25C - 2% VOUT for 0C TJ +125C - 3% VOUT for -40C TJ +125C Overtemperature and Overcurrent Protection Operating Temperature Range: -40C to +125C The fast transient response of this device makes it suitable for use in powering DSP microcontroller core voltages and switch-mode power-supply postregulators. The LP38859 is available in 5-pin TO-220 and DDPAK/TO-263 packages. 2 Applications * * * * ASIC Power Supplies In: - Desktops, Notebooks, Graphics Cards, and Servers - Gaming Set Top Boxes, Printers, and Copiers Server Core and I/O Supplies DSP and FPGA Power Supplies SMPS Post-Regulator Device Information(1) PART NUMBER LP38859 PACKAGE BODY SIZE (NOM) DDPAK/TO-263 (5) 10.16 mm x 8.42 mm TO-220 (5) 14.986 mm x 10.16 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. Typical Application Circuit LP38859-x.x VIN IN VOUT OUT CIN VBIAS 10 PF Ceramic BIAS CBIAS COUT 10 PF Ceramic 1 PF SS GND CSS GND GND 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LP38859 SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 4 6.1 6.2 6.3 6.4 6.5 6.6 4 4 4 4 5 7 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics........................................... Typical Characteristics .............................................. Detailed Description ............................................ 10 7.1 Overview ................................................................. 10 7.2 Functional Block Diagram ....................................... 10 7.3 Feature Description................................................. 10 7.4 Device Functional Modes........................................ 12 8 Application and Implementation ........................ 13 8.1 Application Information............................................ 13 8.2 Typical Application ................................................. 13 9 Power Supply Recommendations...................... 16 10 Layout................................................................... 17 10.1 Layout Guidelines ................................................. 17 10.2 Layout Example .................................................... 17 11 Device and Documentation Support ................. 18 11.1 11.2 11.3 11.4 Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 18 18 18 18 12 Mechanical, Packaging, and Orderable Information ........................................................... 18 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision E (April 2013) to Revision F * Added Device Information, Pin Configuration and Functions and ESD Ratings sections, update Thermal Values, add Feature Description, Device Functional Modes, Application and Implementation, Power Supply Recommendations, Layout, Device and Documentation Support, and Mechanical, Packaging, and Orderable Information sections ................. 1 Changes from Revision D (April 2013) to Revision E * 2 Page Page Changed layout of National data sheet to TI format .............................................................................................................. 1 Submit Documentation Feedback Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 LP38859 www.ti.com SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 5 Pin Configuration and Functions KTT Package 5-Pin DDPAK/TO-263 Top View SS 1 LP38859S-x.x IN 2 GND 3 OUT 4 TAB IS GND BIAS 5 NDH Package 5-Pin TO-220 Top View SS 1 GND 3 OUT 4 LP38859T-x.x IN 2 TAB IS GND BIAS 5 Pin Functions PIN NAME NUMBER I/O DESCRIPTION BIAS 5 I GND 3 -- IN 2 I The unregulated voltage input pin. OUT 4 O The regulated output voltage pin. SS 1 I Soft-start capacitor connection. Used to slow the rise time of VOUT at turnon. TAB -- TAB The supply for the internal control and reference circuitry. Ground The TAB is a thermal connection that is physically attached to the backside of the die, and used as a thermal heat-sink connection. See the Application and Implementation section for details. Submit Documentation Feedback Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 3 LP38859 SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 www.ti.com 6 Specifications 6.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) (2) MIN MAX UNIT VIN supply voltage (survival) -0.3 6 V VBIAS supply voltage (survival) -0.3 6 V VSS soft-start voltage (survival) -0.3 6 V VOUT voltage (survival) -0.3 6 V IOUT current (survival) Internally limited Power dissipation (3) Internally limited Junction temperature 40 150 C Storage temperature, Tstg -65 150 C (1) (2) (3) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. If Military/Aerospace specified devices are required, contact the TI Sales Office/ Distributors for availability and specifications. Device power dissipation must be de-rated based on device power dissipation (PD), ambient temperature (TA), and package junction to ambient thermal resistance (RJA). Additional heat-sinking may be required to ensure that the device junction temperature (TJ) does not exceed the maximum operating rating. See the Application and Implementation section for details. 6.2 ESD Ratings V(ESD) (1) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) VALUE UNIT 2000 V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) MIN VIN supply voltage NOM MAX UNIT (VOUT + VDO) VBIAS V VBIAS supply voltage 3 5.5 V IOUT 0 3 A -40 125 C Junction temperature (1) (1) Device power dissipation must be de-rated based on device power dissipation (PD), ambient temperature (TA), and package junction to ambient thermal resistance (RJA). Additional heat-sinking may be required to ensure that the device junction temperature (TJ) does not exceed the maximum operating rating. See the Application and Implementation section for details. 6.4 Thermal Information LP38859 THERMAL METRIC (1) KTT (DDPAK/TO-263 NDH (TO-220) 5 PINS 5 PINS UNIT RJA Junction-to-ambient thermal resistance 43.2 70.7 (2) C/W RJC(top) Junction-to-case (top) thermal resistance 43.5 43.0 C/W (2) C/W RJB Junction-to-board thermal resistance 23.1 n/a JT Junction-to-top characterization parameter 11.6 23.6 (2) C/W JB Junction-to-board characterization parameter 22.0 52.2 (2) C/W RJC(bot) Junction-to-case (bottom) thermal resistance 1.1 1.3 C/W (1) (2) 4 For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953. The NDH (TO-220) package is vertically mounted in center of JEDEC High-K test board (JESD 51-7) with no additional heat sink. This is a through-hole package; this is NOT a surface mount package. Submit Documentation Feedback Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 LP38859 www.ti.com SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 6.5 Electrical Characteristics Unless otherwise specified: VIN = VOUT(NOM) + 1 V, VBIAS = 3 V, IOUT = 10 mA, CIN = COUT = 10 F, CBIAS = 1 F, CSS = open. Typical limits apply for TJ = 25C; minimum and maximum limits apply over the junction temperature (TJ) range of -40C to +125C, unless otherwise specified. Minimum and maximum limits are specified through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. PARAMETER VOUT VOUT/VIN TEST CONDITIONS VOUT accuracy Line regulation, VIN (1) (1) VOUT/VBIAS Line regulation, VBIAS VOUT/IOUT Output voltage load regulation (2) Dropout voltage (3) VDO MIN IGND(IN) -1% 1% VOUT(NOM) + 1 V VIN VBIAS 3 V VBIAS 5.5 V 10 mA IOUT 3 A -3% 3% VOUT(NOM) + 1 V VIN VBIAS 3 V VBIAS 5.5 V 10 mA IOUT 3 A 0C TJ +125C -2% 2% Quiescent current drawn from VBIAS supply UVLO Undervoltage lockout threshold UVLO(HYS) ISC Undervoltage lockout hysteresis Output short-circuit current UNIT VOUT(NOM) + 1 V VIN VBIAS 0.04 %/V 3 V VBIAS 5.5 V 0.10 %/V 10 mA IOUT 3 A 0.2 IOUT = 3 A, TJ = 25C 240 IOUT = 3 A %/A 300 450 7 LP38859-0.8 10 mA IOUT 3 A mV 8.5 9 mA LP38859-1.2 10 mA IOUT 3 A, TJ = 25C 11 LP38859-1.2 10 mA IOUT 3 A IGND(BIAS) MAX VOUT(NOM) + 1 V VIN VBIAS 3 V VBIAS 5.5 V 10 mA IOUT 3 A, TJ = 25C LP38859-0.8 10 mA IOUT 3 A, TJ = 25C Quiescent current drawn from VIN supply TYP 12 15 10 mA IOUT 3 A, TJ = 25C 3 10 mA IOUT 3 A 3.8 4.5 VBIAS rising until device is functional TJ = 25C 2.2 VBIAS rising until device is functional 2 VBIAS falling from UVLO threshold until device is non-functional TJ = 25C 60 VBIAS falling from UVLO threshold until device is non-functional 50 2.45 2.7 mA V 2.9 150 300 mV VIN = VOUT(NOM) + 1 V 350 6.2 VBIAS = 3 V, VOUT = 0 V A SOFT-START rSS Soft-start internal resistance tSS Soft-start time tSS = CSS x rSS x 5 (1) (2) (3) LP38859-0.8 11 13.5 16 LP38859-1.2 13.5 16 18.5 LP38859-0.8, CSS = 10 nF 675 LP38859-1.2, CSS = 10 nF 800 k s Output voltage line regulation is defined as the change in output voltage from nominal value resulting from a change in input voltage. Output voltage load regulation is defined as the change in output voltage from nominal value as the load current increases from no load to full load. Dropout voltage is defined the as input to output voltage differential (VIN - VOUT) where the input voltage is low enough to cause the output voltage to drop no more than 2% from the nominal value. Submit Documentation Feedback Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 5 LP38859 SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 www.ti.com Electrical Characteristics (continued) Unless otherwise specified: VIN = VOUT(NOM) + 1 V, VBIAS = 3 V, IOUT = 10 mA, CIN = COUT = 10 F, CBIAS = 1 F, CSS = open. Typical limits apply for TJ = 25C; minimum and maximum limits apply over the junction temperature (TJ) range of -40C to +125C, unless otherwise specified. Minimum and maximum limits are specified through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25C, and are provided for reference purposes only. PARAMETER TEST CONDITIONS MIN TYP MAX UNIT AC PARAMETERS PSRR (VIN) Ripple rejection for VIN input voltage PSRR (VBIAS) Ripple rejection for VBIAS voltage Output noise density en Output noise voltage VIN = VOUT(NOM) + 1 V = 120 Hz 80 VIN = VOUT(NOM) + 1 V = 1 kHz 65 VBIAS = VOUT(NOM) + 3 V f = 120 Hz 58 VBIAS = VOUT(NOM) + 3 V = 1 kHz 58 dB = 120 Hz 1 BW = 10 Hz - 100 kHz, VOUT = 1.8 V 150 BW = 300 Hz - 300 kHz, VOUT = 1.8 V 90 V/Hz VRMS THERMAL PARAMETERS TSD Thermal shutdown junction temperature TSD(HYS) Thermal shutdown hysteresis 6 Submit Documentation Feedback 160 C 10 C Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 LP38859 www.ti.com SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 6.6 Typical Characteristics Unless otherwise specified: TJ = 25C, VIN = VOUT(NOM) + 1 V, VBIAS = 3 V, IOUT = 10 mA, CIN = COUT = 10-F ceramic, CBIAS = 1-F ceramic, CSS = open. Figure 1. VBIAS Ground Pin Current (IGND(BIAS)) vs VBIAS Figure 2. VBIAS Ground Pin Current (IGND(BIAS)) vs Temperature Figure 3. VIN Ground Pin Current vs Temperature Figure 4. Load Regulation vs Temperature Figure 5. Dropout Voltage (VDO) vs Temperature Figure 6. Output Current Limit (ISC) vs Temperature Submit Documentation Feedback Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 7 LP38859 SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 www.ti.com Typical Characteristics (continued) Unless otherwise specified: TJ = 25C, VIN = VOUT(NOM) + 1 V, VBIAS = 3 V, IOUT = 10 mA, CIN = COUT = 10-F ceramic, CBIAS = 1-F ceramic, CSS = open. Figure 7. VOUT vs Temperature Figure 8. UVLO Thresholds vs Temperature Figure 9. Soft-Start Resistor (RSS) vs Temperature Figure 10. Soft-Start RSS Variation vs Temperature 10 nF To 47 nF Figure 11. VOUT vs CSS 8 Figure 12. VIN Line Transient Response Submit Documentation Feedback Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 LP38859 www.ti.com SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 Typical Characteristics (continued) Unless otherwise specified: TJ = 25C, VIN = VOUT(NOM) + 1 V, VBIAS = 3 V, IOUT = 10 mA, CIN = COUT = 10-F ceramic, CBIAS = 1-F ceramic, CSS = open. Figure 13. VIN Line Transient Response Figure 14. VBIAS Line Transient Response Figure 15. VBIAS Line Transient Response Figure 16. VBIAS PSRR Figure 17. VIN PSRR Figure 18. Output Noise Submit Documentation Feedback Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 9 LP38859 SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 www.ti.com 7 Detailed Description 7.1 Overview The LP38559 is a fast-response, high-current, low-dropout regulator, available in output voltages are 0.8 V and 1.2 V. This part is capable of delivering 3-A continuous load current. Standard regulator features, such as overcurrent and over temperature protection, are also included. The LP38559 contains several features: * Low dropout voltage, typical 240 mV at 3-A load. * The bias voltage(VBIAS) provides voltage to drive the gate of the N-MOS power transistor. * The input voltage(VIN) is the input voltage which supplies power to the load. * Programmable soft-start time. 7.2 Functional Block Diagram OUT IN LP38859-x.x BIAS Undervoltage Lockout Thermal Shutdown rSS SS VREF ILIMIT GND 0.6 V 7.3 Feature Description 7.3.1 Input Voltage The input voltage (VIN) is the high current external voltage rail that is regulated down to a lower voltage, which is applied to the load. The input voltage must be at least VOUT + VDO, and no higher than whatever values is used for VBIAS. 7.3.2 Bias Voltage The bias voltage (VBIAS) is a low current external voltage rail required to bias the control circuitry and provide gate drive for the N-FET pass transistor. The bias voltage must be in the range of 3 V to 5.5 V to ensure proper operation of the device. 10 Submit Documentation Feedback Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 LP38859 www.ti.com SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 Feature Description (continued) 7.3.3 Undervoltage Lockout The bias voltage is monitored by a circuit which prevents the device from functioning when the bias voltage is below the undervoltage lockout (UVLO) threshold of approximately 2.45 V. As the bias voltage rises above the UVLO threshold the device control circuitry becomes active. There is approximately 150 mV of hysteresis built into the UVLO threshold to provide noise immunity. When the bias voltage is between the UVLO threshold and the minimum operating rating value of 3 V, the device is functional, but the operating parameters are not within the specified limits. 7.3.4 Supply Sequencing There is no requirement for the order that VIN or VBIAS are applied or removed. One practical limitation is that the soft-start circuit starts charging CSS when VBIAS rises above the UVLO threshold. If the application of VIN is delayed beyond this point the benefits of soft start are compromised. In any case, the output voltage cannot be specified until both VIN and VBIAS are within the range of specified operating values. If used in a dual-supply system where the regulator output load is returned to a negative supply, the output pin must be diode clamped to ground. A Schottky diode is recommended for this diode clamp. 7.3.5 Reverse Voltage A reverse voltage condition exists when the voltage at the output pin is higher than the voltage at the input pin. Typically this happens when VIN is abruptly taken low and COUT continues to hold a sufficient charge such that the input to output voltage becomes reversed. The NMOS pass element, by design, contains no body diode. This means that, as long as the gate of the pass element is not driven, there is no reverse current flow through the pass element during a reverse voltage event. The gate of the pass element is not driven when VBIAS is below the UVLO threshold. When VBIAS is above the UVLO threshold, the control circuitry is active and attempts to regulate the output voltage. Because the input voltage is less than the output voltage the control circuit drives the gate of the pass element to the full VBIAS potential when the output voltage begins to fall. In this condition, reverse current flows from the OUT pin to the IN pin , limited only by the RDS(ON) of the pass element and the output to input voltage differential. This condition is outside the specified operating range and must be avoided. 7.3.6 Soft-Start The LP38859 incorporates a soft-start function that reduces the start-up current surge into the output capacitor (COUT) by allowing VOUT to rise slowly to the final value. This is accomplished by controlling VREF at the SS pin. The soft-start timing capacitor (CSS) is internally held to ground until VBIAS rises above the UVLO threshold. VREF rises at an RC rate defined by the internal resistance of the SS pin (rSS), and the external capacitor connected to the SS pin. This allows the output voltage to rise in a controlled manner until steady-state regulation is achieved. Typically, five time constants are recommended to assure that the output voltage is sufficiently close to the final steady-state value. During the soft-start time the output current can rise to the built-in current limit. Soft-Start Time = CSS x rSS x 5 (1) Because the VOUT rise is exponential, not linear, the in-rush current peaks during the first time constant (), and VOUT requires four additional time constants (4) to reach the final value (5) . After achieving normal operation, if VBIAS falsl below the ULVO threshold, the device output is disabled, and the soft-start capacitor (CSS) discharge circuit becomes active. The CSS discharge circuit remains active until VBIAS falls to 500 mV (typical). When VBIAS falls below 500 mV (typical), the CSS discharge circuit ceases to function due to a lack of sufficient biasing to the control circuitry. Submit Documentation Feedback Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 11 LP38859 SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 www.ti.com Feature Description (continued) Because VREF appears on the SS pin, any leakage through CSS causes VREF to fall, and thus affect VOUT. A leakage of 50 nA (about 10 M) through CSS causes VOUT to be approximately 0.1% lower than nominal, while a leakage of 500 nA (about 1 M) causes VOUT to be approximately 1% lower than nominal. Typical ceramic capacitors have a factor of 10x difference in leakage between 25C and 85C, so the maximum ambient temperature must be included in the capacitor selection process. Typical CSS values are in the range of 1 nF to 100 nF, providing typical soft-start times in the range of 70 s to 7 ms (5). Values less than 1 nF can be used, but the soft-start effect is minimal. Values larger than 100 nF provide soft start, but may not be fully discharged if VBIAS falls from the UVLO threshold to less than 500 mV in less than 100 s. Figure 19 shows the relationship between the COUT value and a typical CSS value. Figure 19. Typical CSS vs COUT Values The CSS capacitor must be connected to a clean ground path back to the device ground pin. No components, other than CSS, should be connected to the SS pin, as there could be adverse effects to VOUT. If the soft-start function is not needed, the SS pin must be left open, although some minimal capacitance value is always recommended. 7.4 Device Functional Modes 7.4.1 Operation with 3 V VBIAS 5.5 V, VOUT(TARGET)+ 0.3 V VIN VBIAS The device operates if the bias voltage is equal to, or exceeds, 3 V, and input voltage is equal to, or exceeds, VOUT(TARGET) + 0.3 V. At bias voltages below the minimum VBIAS requirement, the device does not operate correctly, and output voltage may not reach target value. 12 Submit Documentation Feedback Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 LP38859 www.ti.com SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information The LP38859 can provide 3-A output current with 240-mV dropout voltage (typical). The bias voltage must be in the range of 3 V to 5.5 V to ensure proper operation of the device. The input voltage must be at least VOUT + VDO, and no higher than whatever value is used for VBIAS. Minimal input and output capacitors are each 10 F. The capacitor on the BIAS pin must be at least 1 F. 8.2 Typical Application LP38859-x.x VIN IN VOUT OUT CIN 10 PF Ceramic VBIAS BIAS CBIAS COUT 10 PF Ceramic 1 PF SS GND CSS GND GND Figure 20. LP38859 Typical Application 8.2.1 Design Requirements For typical high-accuracy LDO linear regulator applications, use the parameters listed in Table 1. Table 1. Design Parameters DESIGN PARAMETER EXAMPLE VALUE Bias voltage 3 V to 5.5 V Input voltage 1.1 V to 5.5 V Output voltages 0.8 V, 1.2 V Output current 3 A (maximum) Bias capacitor 1 F (minimum) Input capacitor 10 F (minimum) Output capacitor 10 uF (minimum) 8.2.2 Detailed Design Procedure 8.2.2.1 External Capacitors To assure regulator stability, input and output capacitors are required as shown in the Figure 20. 8.2.2.1.1 Output Capacitor A minimum output capacitance of 10 F, ceramic, is required for stability. The amount of output capacitance can be increased without limit. The output capacitor must be located less than 1 cm from the OUT pin of the device and returned to the device GND pin with a clean analog ground. Only high quality ceramic types such as X5R or X7R must be used, as the Z5U and Y5F types do not provide sufficient capacitance over temperature. Submit Documentation Feedback Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 13 LP38859 SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 www.ti.com Tantalum capacitors also provide stable operation across the entire operating temperature range. However, the effects of ESR may provide variations in the output voltage during fast load transients. Using the minimum recommended 10-F ceramic capacitor at the output allows unlimited capacitance, tantalum, and/or aluminum, to be added in parallel. 8.2.2.1.2 Input Capacitor The input capacitor must be at least 10 F, but can be increased without limit. Its purpose is to provide a low source impedance for the regulator input. A ceramic capacitor, X5R or X7R, is recommended. Tantalum capacitors may also be used at the IN pin. There is no specific ESR limitation on the input capacitor (the lower, the better). Aluminum electrolytic capacitors can be used, but are not recommended as their ESR increases very quickly at cold temperatures. They are not recommended for any application where the ambient temperature falls below 0C. 8.2.2.1.3 Bias Capacitor The capacitor on the BIAS pin must be at least 1 F and can be any good-quality capacitor (ceramic is recommended). 8.2.2.2 Power Dissipation and Heat-Sinking Additional copper area for heat-sinking may be required depending on the maximum device dissipation (PD) and the maximum anticipated ambient temperature (TA) for the device. Under all possible conditions, the junction temperature must be within the range specified under operating conditions. The total power dissipation of the device is the sum of three different points of dissipation in the device. The first part is the power that is dissipated in the NMOS pass element, and can be determined with the formula: PD(PASS) = (VIN - VOUT) x IOUT (2) The second part is the power that is dissipated in the bias and control circuitry, and can be determined with the formula: PD(BIAS) = VBIAS x IGND(BIAS) where * IGND(BIAS) is the portion of the operating ground current of the device that is related to VBIAS. (3) The third part is the power that is dissipated in portions of the output stage circuitry, and can be determined with the formula: PD(IN) = VIN x IGND(IN) where * IGND(IN) is the portion of the operating ground current of the device that is related to VIN. (4) The total power dissipation is then: PD = PD(PASS) + PD(BIAS) + PD(IN) (5) The maximum allowable junction temperature rise (TJ) depends on the maximum anticipated ambient temperature (TA) for the application, and the maximum allowable operating junction temperature (TJ(MAX)) . TJ = TJ(MAX) - TA(MAX) (6) The maximum allowable value for junction-to-ambient thermal resistance, RJA, can be calculated using Equation 7. RJA TJ / PD 14 (7) Submit Documentation Feedback Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 LP38859 www.ti.com SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 8.2.3 Application Curves COUT = 10-F ceramic COUT = 10-F ceramic Figure 21. Load Transient Response COUT = 100-F ceramic Figure 22. Load Transient Response COUT = 100-F ceramic Figure 23. Load Transient Response COUT = 100-F tantalum Figure 24. Load Transient Response COUT = 100-F tantalum Figure 25. Load Transient Response Figure 26. Load Transient Response Submit Documentation Feedback Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 15 LP38859 SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 www.ti.com 9 Power Supply Recommendations The LP38859 device is designed to operate from an input voltage supply range from 3 V and 5.5 V. The input voltage range provides adequate headroom in order for the device to have a regulated output. This input supply must be well regulated. An input capacitor of at least 10 F is required. 16 Submit Documentation Feedback Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 LP38859 www.ti.com SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 10 Layout 10.1 Layout Guidelines The dynamic performance of the LP38859 is dependent on the layout of the PCB. PCB layout practices that are adequate for typical LDOs may degrade the PSRR, noise, or transient performance of the LP38859. Best performance is achieved by placing CIN and COUT on the same side of the PCB as the LP38859, and as close as is practical to the package. The ground connections for CIN and COUT must be back to the LP38859 ground pin using as wide and short of a copper trace as is practical. Good PC layout practices must be used or instability can be induced because of ground loops and voltage drops. The input and output capacitors must be directly connected to the IN, OUT, and GND pins of the LP38859 using traces which do not have other currents flowing in them (Kelvin connect). The best way to do this is to lay out CIN and COUT near the device with short traces to the IN, OUT, and GND pins. The regulator ground pin must be connected to the external circuit ground so that the regulator and its capacitors have a single-point ground. Stability problems have been seen in applications where vias to an internal ground plane were used at the ground points of the LP38859 device and the input and output capacitors. This was caused by varying ground potentials at these nodes resulting from current flowing through the ground plane. Using a single point ground technique for the regulator and its capacitors fixed the problem. Because high current flows through the traces going into the IN pin and coming from the OUT pin, Kelvin connect the capacitor leads to these pins so there is no voltage drop in series with the input and output capacitors. 10.2 Layout Example CSS SS VIN IN CIN GND COUT OUT BIAS VOUT CBIAS Figure 27. LP38859 Layout Example Submit Documentation Feedback Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 17 LP38859 SNVS337F - JUNE 2006 - REVISED SEPTEMBER 2015 www.ti.com 11 Device and Documentation Support 11.1 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2ETM Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 11.2 Trademarks E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. 11.3 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 11.4 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 18 Submit Documentation Feedback Copyright (c) 2006-2015, Texas Instruments Incorporated Product Folder Links: LP38859 PACKAGE OPTION ADDENDUM www.ti.com 8-Oct-2015 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LP38859S-1.2/NOPB ACTIVE DDPAK/ TO-263 KTT 5 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP38859S -1.2 LP38859SX-1.2/NOPB ACTIVE DDPAK/ TO-263 KTT 5 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP38859S -1.2 LP38859T-0.8/NOPB ACTIVE TO-220 NDH 5 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LP38859T -0.8 LP38859T-1.2/NOPB ACTIVE TO-220 NDH 5 45 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 125 LP38859T -1.2 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 8-Oct-2015 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 2-Sep-2015 TAPE AND REEL INFORMATION *All dimensions are nominal Device LP38859SX-1.2/NOPB Package Package Pins Type Drawing SPQ DDPAK/ TO-263 500 KTT 5 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 330.0 24.4 Pack Materials-Page 1 10.75 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 14.85 5.0 16.0 24.0 Q2 PACKAGE MATERIALS INFORMATION www.ti.com 2-Sep-2015 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP38859SX-1.2/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 Pack Materials-Page 2 MECHANICAL DATA NDH0005D www.ti.com MECHANICAL DATA KTT0005B TS5B (Rev D) BOTTOM SIDE OF PACKAGE www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2015, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LP38859S-0.8 LP38859S-0.8/NOPB LP38859S-1.2 LP38859S-1.2/NOPB LP38859SX-0.8 LP38859SX-0.8/NOPB LP38859SX-1.2 LP38859SX-1.2/NOPB LP38859T-0.8 LP38859T-0.8/NOPB LP38859T-1.2 LP38859T-1.2/NOPB