ST www.vishay.com Vishay SuperTan(R) Wet Tantalum Capacitors with Hermetic Seal FEATURES * * * * * * * * * Very high capacitance 10 F to 1800 F 25 VDC to 125 VDC Very low ESR High ripple current All Tantalum case Hermetically sealed Low DCL Axial through-hole terminations: Standard tin/lead (Sn/Pb) 100 % tin (RoHS compliant) available * Compliant to RoHS Directive 2002/95/EC Vishay ST represents a major breakthrough in wet tantalum capacitor technology. Its unique cathode system provides the highest capacitance per unit volume. The design facilitates a doubling of capacitance, lower ESR and higher ripple current rating compared with conventional wet tantalum products. Moreover, the ST has the capacitance stability of a solid tantalum capacitor and there are no circuit impedance restrictions. Note * Pb containing terminations are not RoHS compliant, exemptions may apply APPLICATION NOTES a. No continuous reverse voltage permissible. b. The peak of the applied AC ripple and the applied DC voltage must not exceed the DC voltage rating of the capacitor. c. Ripple current ratings by part number at 85 C and 40 kHz are included in the table. Ripple current correction factors for other temperatures and frequencies are given on the next page. d. Transient reverse voltage surges are acceptable under the following conditions: The peak reverse voltage does not exceed 1.5 V and the peak current times the duration of the reverse transient does not exceed 0.05 As. In addition, the repetition frequency of the reverse voltage surge is less than 10 Hz. The ST is housed in an all tantalum, hermetically sealed case and is manufactured to withstand hazardous environments. The ST is used widely in the defense and aerospace industries and whenever there is a space problem. PERFORMANCE CHARACTERISTICS Operating Temperature: - 55 C to + 85 C (to + 125 C with voltage derating) Capacitance Tolerance: At 120 Hz, + 25 C. 20 % standard. 10 % available as special. DIMENSIONS in inches [millimeters] Terminal welded to case 0.025 + 0.002 [0.64 + 0.05] 0.250 [6.35] MAX. 0.094 [2.38] MAX. E L "D" DIA. E Terminal location within 0.031 of center CASE CODE D 0.016 (0.41) MAX. INSULATED (DIA.) L1 + 0.031 (0.79) UNINSULATED E 0.250 (6.35) MAX. T1 0.188 [4.78] 0.219 [5.56] 0.453 [11.51] 1.500 [38.10] T2 0.281 [7.14] 0.312 [7.92] 0.641 [16.28] 2.250 [57.15] L2 0.281 [7.14] 0.312 [7.92] 1.008 [25.60] 2.250 [57.15] T3 0.375 [9.52] 0.406 [10.31] 0.766 [19.46] 2.250 [57.15] T4 0.375 [9.52] 0.406 [10.31] 1.062 [26.97] 2.250 [57.15] Notes * Material at egress is Tantalum * Insulation sleeving will lap over the ends of the capacitor case * Tinned nickel leads, solderable and weldable * Approx. weight: T1: 2.3 g, T2: 5.7 g, T3: 9.4 g, T4: 14.8 g Revision: 05-Sep-11 1 Document Number: 43000 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 ST www.vishay.com Vishay ORDERING INFORMATION ST 220 100 T4 M I E3 Super Tan(R) COMMERCIAL CAP. TYPE CAPACITANCE F 85 C RATED DC VOLTAGE CASE CODE CAPACITANCE TOLERANCE INSULATING SLEEVE RoHS compliant M = 20 % K = 10 % I = Insulated X = Uninsulated E3 = 100 % tin termination (RoHS compliant) Blank = SnPb termination (standard design) STANDARD RATINGS MAX. DCL AT MAX. IMP. AT - 55 C AND 120 Hz () MAX. CAPACITANCE CHANGE AT + 125 C (%) AC RIPPLE 85 C 40 kHz (mA) RMS PART NUMBER +8 + 12 1250 ST120-25T1MI + 10 + 15 2100 ST560-25T2MI + 20 + 45 3200 ST1100-25L2MI - 70 + 12 + 18 2600 ST1200-25T3MI - 72 + 12 + 20 3100 ST1800-25T4MI CAPACITANCE AT 25 C AND 120 Hz (F) CASE CODE MAX. ESR 120 Hz () + 25 C (A) + 85 C/ + 125 C (A) 120 T1 1.3 1 5 25 - 42 560 T2 0.83 2 10 12 - 65 1100 L2 0.5 3 25 7 - 60 1200 T3 0.65 5 20 7 1800 T4 0.5 6 25 7 - 55 C (%) + 85 C (%) 25 VDC AT 85 C; 15 VDC AT 125 C 30 VDC AT 85 C; 20 VDC AT 125 C 100 T1 1.3 1 5 25 - 38 +8 + 12 1200 ST100-30TMI 470 T2 0.85 2 10 15 - 65 + 10 + 18 1800 ST470-30T2MI 950 L2 0.5 5 30 7 - 55 + 18 + 35 3200 ST950-30L2MI 1000 T3 0.7 7 25 7 - 70 + 10 + 18 2500 ST1000-30T3MI 1500 T4 0.6 12 35 6 - 72 + 10 + 20 3000 ST1500-30T4MI 50 VDC AT 85 C; 30 VDC AT 125 C 68 T1 1.5 1 5 35 - 25 +8 + 15 1050 ST68-50T1MI 220 T2 0.9 2 10 17.5 - 50 +8 + 15 1800 ST220-50T2MI 450 L2 0.6 3 25 7.5 - 45 + 12 + 30 2900 ST450-50L2MI 470 T3 0.75 3 25 10 - 45 +8 + 15 2100 ST470-50T3MI 680 T4 0.7 5 40 8 - 58 + 10 + 20 2750 ST680-50T4MI 60 VDC AT 85 C; 40 VDC AT 125 C 47 T1 2.0 1 5 44 - 25 +8 + 12 1050 ST47-60T1MI 150 T2 1.1 2 10 20 - 40 +8 + 15 1800 ST150-60T2MI 370 L2 0.6 3 25 9 - 33 +9 + 20 2900 ST370-60L2MI 390 T3 0.9 3 25 15 - 45 +8 + 15 2100 ST390-60T3MI 560 T4 0.8 5 40 10 - 58 +8 + 15 2750 ST560-60T4MI 75 VDC AT 85 C; 50 VDC AT 125 C 33 T1 2.5 1 5 66 - 25 +5 +9 1050 ST33-75T1MI 110 T2 1.3 2 10 24 - 35 +6 + 10 1650 ST110-75T2MI 250 L2 0.8 5 30 12 - 30 +6 + 15 2500 ST250-75L2MI 330 T3 1.0 3 30 12 - 45 +6 + 10 2100 ST330-75T3MI 470 T4 0.9 5 50 12 - 50 +6 + 10 2750 ST470-75T4MI Notes * (K = 10 %, M = 20 %) and insulation letter (I =Insulation, X = Uninsulated) * Part numbers shown are for units with 20 % capacitance tolerance and uninsulated capacitors. For 10 units, change the digit following the letter "X" from "0" to "9". For units with outer plastic-film insulation, substitute "2" for "0" at the end of the part number * For RoHS compliant add "E3" for suffix Revision: 05-Sep-11 2 Document Number: 43000 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 ST www.vishay.com Vishay STANDARD RATINGS CAPACITANCE AT 25 C AND 120 Hz (F) MAX. DCL AT CASE CODE MAX. ESR 120 Hz () + 25 C (A) 15 T1 3.5 1 + 85 C/ + 125 C (A) MAX. CAPACITANCE CHANGE AT MAX. IMP. AT - 55 C AND 120 Hz () - 55 C (%) + 85 C (%) + 125 C (%) AC RIPPLE 85 C 40 kHz (mA) RMS PART NUMBER + 10 1050 ST15-100T1MI 100 VDC AT 85 C; 65 VDC AT 125 C 5 125 - 18 +3 68 T2 2.1 2 10 37 - 30 +4 + 12 1650 ST68-100T2MI 120 L2 1.0 3 25 20.5 - 30 +4 + 12 2200 ST120-100L2MI 150 T3 1.6 3 25 22 - 35 +6 + 12 2100 ST150-100T3MI 220 T4 1.2 5 50 15 - 40 +6 + 12 2750 ST220-100T4MI 125 VDC AT 85 C; 85 VDC AT 125 C 10 T1 5.5 1 5 175 - 15 +3 + 10 1050 ST10-125T1MI 47 T2 2.3 2 10 47 - 25 +5 + 12 1650 ST47-125T2MI 90 L2 1.3 5 25 25 - 22 +4 + 15 2000 ST90-125L2MI 82 T3 100 T3 1.8 3 25 Preliminary value, contact marketing 35 - 35 +5 + 12 2100 ST100-125T3MI ST82-125T3MI 150 T4 1.6 5 50 20 - 35 +6 + 12 2750 ST150-125T4MI Notes * (K = 10 %, M = 20 %) and insulation letter (I =Insulation, X = Uninsulated) * Part numbers shown are for units with 20 % capacitance tolerance and uninsulated capacitors. For 10 units, change the digit following the letter "X" from "0" to "9". For units with outer plastic-film insulation, substitute "2" for "0" at the end of the part number * For RoHS compliant add "E3" for suffix RIPPLE CURRENT MULTIPLIERS VS. FREQUENCY, TEMPERATURE AND APPLIES PEAK VOLTAGE FREQUENCY OF APPLIED RIPPLE CURRENT 120 Hz 800 Hz 1 kHz 10 kHz 40 kHz 100 kHz AMBIENT STILL 55 85 105 125 55 85 105 125 55 85 105 125 55 85 105 125 55 85 105 125 55 85 105 125 AIR TEMP. IN C 100 % % of 85 C rated peak voltage 0.60 0.39 - - 0.71 0.43 - - 0.72 0.46 - - 0.88 0.55 - 90 % 0.60 0.46 - - 0.71 0.55 - - 0.72 0.55 - 80 % 0.60 0.52 0.35 - 0.71 0.62 0.42 - 0.72 0.62 0.42 70 % 0.60 0.58 0.44 - 0.71 0.69 0.52 - 0.72 0.70 0.52 - - 1.0 0.63 - - - 0.88 0.67 - - 0.88 0.76 0.52 0.88 0.85 0.64 - 1.1 0.69 - - 1.0 0.77 - - 1.0 0.87 0.59 1.0 0.97 0.73 - - 1.1 0.85 - - 1.1 0.96 0.65 - - 1.1 1.07 0.80 - - 66 2/3 % 0.60 0.60 0.46 0.27 0.71 0.71 0.55 0.32 0.72 0.72 0.55 0.32 0.88 0.88 0.68 0.40 1.0 1.0 0.77 0.45 1.1 1.1 0.85 0.50 Revision: 05-Sep-11 3 Document Number: 43000 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 11-Mar-11 www.vishay.com 1