MAX803/MAX809/ MAX810 3-Pin Microprocessor Reset Circuits General Description Benefits and Features The MAX803/MAX809/MAX810 are microprocessor (P) supervisory circuits used to monitor the power supplies in P and digital systems. They provide excellent circuit reliability and low cost by eliminating external components and adjustments when used with +5V, +3.3V, +3.0V, or +2.5V powered circuits. These circuits perform a single function: they assert a reset signal whenever the VCC supply voltage declines below a preset threshold, keeping it asserted for at least 140ms after VCC has risen above the reset threshold. Reset thresholds suitable for operation with a variety of supply voltages are available. The MAX803 has an open-drain output stage, while the MAX809/MAX810 have push-pull outputs. The MAX803's open-drain RESET output requires a pullup resistor that can be connected to a voltage higher than VCC. The MAX803/MAX809 have an active-low RESET output, while the MAX810 has an active-high RESET output. The reset comparator is designed to ignore fast transients on VCC, and the outputs are guaranteed to be in the correct logic state for VCC down to 1V. Low supply current makes the MAX803/MAX809/MAX810 ideal for use in portable equipment. The MAX803 is available in a 3-pin SC70 package, and the MAX809/ MAX810 are available in 3-pin SC70 or SOT23 packages. Precision Monitoring of +2.5V, +3V, +3.3V, and +5V Power-Supply Voltages Fully Specified Over Temperature Available in Three Output Configurations * Open-Drain RESET Output (MAX803) * Push-Pull RESET Output (MAX809) * Push-Pull RESET Output (MAX810) 140ms (min) Power-On-Reset Pulse Width 12A Supply Current Guaranteed Reset Valid to VCC = +1V Power Supply Transient Immunity No External Components 3-Pin SC70 and SOT23 Packages Selector Guide and Ordering Information appear at end of data sheet. Typical Operating Circuit VCC MAX803 MAX809 RESET Applications Computers Controllers Intelligent Instruments Critical P and C Power Monitoring Portable/Battery-Powered Equipment Automotive 19-0344; Rev 10; 12/15 VCC VCC GND *MAX803 ONLY RPULLUP* P RESET INPUT GND MAX803/MAX809/ MAX810 3-Pin Microprocessor Reset Circuits Absolute Maximum Ratings Terminal Voltage (with respect to GND) VCC. ..................................................................-0.3V to +6.0V RESET, RESET (push-pull)................... -0.3V to (VCC + 0.3V) RESET (open drain)..........................................-0.3V to +6.0V Input Current, VCC..............................................................20mA Output Current, RESET, RESET.........................................20mA Rate of Rise, VCC...........................................................100V/s Continuous Power Dissipation (TA = +70C) 3-Pin SC70 (derate 2.17mW/C above +70C)............174mW 3-Pin SOT23 (derate 4mW/C above +70C)..............320mW Operating Temperature Range 3-Pin SC70.................................................... -40C to +125C 3-Pin SOT23.................................................. -40C to +105C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) .................................+300C Soldering Temperature (reflow) .......................................+260C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Electrical Characteristics (VCC = full range, TA = -40C to +105C (SOT23) or TA = -40C to +125C (SC70), unless otherwise noted. Typical values are at TA = +25C, VCC = 5V for L/M/J versions, VCC = 3.3V for T/S versions, VCC = 3V for R version, and VCC = 2.5V for Z version.) (Note 1) PARAMETER SYMBOL VCC Range Supply Current (SOT23) Supply Current (SC70) CONDITIONS ICC 5.5 1.2 5.5 TA = -40C to +125C (MAX8_ _ _EXR) 1.2 5.5 TA = -40C to +85C VCC < 5.5V, MAX8_ _L/M TA = +85C to +105C VCC < 5.5V, MAX8_ _L/M TA = -40C to +85C VCC < 5.5V, MAX8_ _L/M TA = +85C to +125C VCC < 5.5V, MAX8_ _L/M MAX8_ _M MAX809J (SOT only) VTH MAX8_ _T MAX8_ _S MAX8_ _R www.maximintegrated.com MAX 1.0 MAX8_ _L Reset Threshold (SOT only) TYP TA = 0C to +70C TA = -40C to +105C (MAX8_ _ _EUR) ICC MIN VCC < 3.6V, MAX8_ _R/S/T/Z 60 17 50 V 100 VCC < 3.6V, MAX8_ _R/S/T/Z 100 VCC < 3.6V, MAX8_ _R/S/T/Z VCC < 3.6V, MAX8_ _R/S/T/Z 24 UNITS 24 35 17 30 A 60 60 TA = +25C 4.56 TA = -40C to +125C 4.40 TA = -40C to +85C TA = +25C 3.93 TA = -40C to +125C 3.80 TA = -40C to +85C 3.00 TA = +25C 2.89 4.63 4.70 TA = -40C to +85C 4.50 4.75 TA = +25C 4.31 4.25 4.50 TA = -40C to +125C 4.16 4.56 TA = -40C to +85C 3.89 TA = +25C 3.04 TA = -40C to +125C 2.92 TA = -40C to +85C 2.85 3.00 TA = -40C to +125C 2.78 3.08 TA = +25C 2.59 TA = -40C to +85C 2.55 2.70 TA = -40C to +125C 2.50 2.76 4.86 4.38 4.00 4.45 4.06 4.10 4.20 3.08 3.11 V 3.15 3.23 2.93 2.63 2.96 2.66 Maxim Integrated 2 MAX803/MAX809/ MAX810 3-Pin Microprocessor Reset Circuits Electrical Characteristics (continued) (VCC = full range, TA = -40C to +105C (SOT23) or TA = -40C to +125C (SC70), unless otherwise noted. Typical values are at TA = +25C, VCC = 5V for L/M/J versions, VCC = 3.3V for T/S versions, VCC = 3V for R version, and VCC = 2.5V for Z version.) (Note 1) PARAMETER SYMBOL CONDITIONS MAX8_ _L MAX8_ _M MAX8_ _T Reset Threshold (SC70 only) VTH MAX8_ _S MAX8_ _R MAX8_ _Z (SC70 only) Reset Threshold Tempco MIN TYP MAX TA = +25C 4.56 4.63 4.70 TA = -40C to +125C 4.44 TA = -40C to +85C 4.25 TA = +25C 3.04 TA = -40C to +125C 2.95 TA = -40C to +85C 2.85 TA = +25C 2.59 TA = -40C to +125C 2.52 TA = -40C to +85C 2.25 TA = -40C to +85C 4.50 TA = +25C 4.31 TA = -40C to +125C 4.20 TA = -40C to +85C 3.00 TA = +25C 2.89 TA = -40C to +125C 2.81 TA = -40C to +85C 2.55 TA = +25C 2.28 TA = -40C to +125C 2.22 VCC = VTH to (VTH - 100mV) TA = +85C to +105C 100 TA = +85C to +125C 100 Reset Active Timeout Period (SOT23) 140 Reset Active Timeout Period (SC70) TA = -40C to +85C 140 RESET Output Voltage High (push-pull active low MAX809) RESET Output Voltage Low (push-pull active high, MAX810) www.maximintegrated.com VOL VOH VOL 4.82 4.38 4.45 4.50 4.56 3.08 3.11 3.15 3.21 2.93 2.96 3.05 2.63 2.66 2.70 2.74 2.32 2.35 2.38 2.42 ppm/C s 240 560 840 240 460 840 VCC = VTH (min), ISINK = 1.2mA, MAX803R/S/T/Z, MAX809R/S/T/Z 0.3 VCC = VTH (min), ISINK = 3.2mA, MAX803L/M, MAX809J/L/M 0.4 VCC > 1.0V, ISINK = 50A 0.3 VCC > VTH (max), ISOURCE = 500A, MAX803R/S/T/Z, MAX809R/S/T/Z 0.8VCC VCC > VTH (max), ISOURCE = 800A, MAX803L/M, MAX809J/L/M VCC - 1.5 V 3.00 20 TA = -40C to +85C RESET Output Voltage Low (push-pull active low and opendrain active low, MAX803 and MAX809) 4.75 30 VCC to Reset Delay (Note 2) UNITS ms ms V V VCC = VTH (max), ISINK = 1.2mA, MAX810R/S/T/Z 0.3 VCC = VTH (max), ISINK = 3.2mA, MAX810L/M 0.4 V Maxim Integrated 3 MAX803/MAX809/ MAX810 3-Pin Microprocessor Reset Circuits Electrical Characteristics (continued) (VCC = full range, TA = -40C to +105C (SOT23) or TA = -40C to +125C (SC70), unless otherwise noted. Typical values are at TA = +25C, VCC = 5V for L/M/J versions, VCC = 3.3V for T/S versions, VCC = 3V for R version, and VCC = 2.5V for Z version.) (Note 1) PARAMETER SYMBOL RESET Output Voltage High (push-pull active high, MAX810) VOH CONDITIONS MIN 1.8V < VCC < VTH (min), ISOURCE = 150A RESET Open-Drain Output Leakage Current (MAX803) (Note 3) TYP MAX UNITS 0.8VCC V VCC > VTH, RESET deasserted 1 A Note 1: Production testing done at TA = +25C; limits over temperature guaranteed by design only. Note 2: RESET output for MAX803/MAX809; RESET output for MAX810. Note 3: Guaranteed by design, not production tested. Typical Operating Characteristics (VCC = full range, TA = -40C to +105C, unless otherwise noted. Typical values are at TA = +25C, VCC = +5V for L/M/J versions, VCC = +3.3V for T/S versions, VCC = +3V for R version, and VCC = +2.5V for Z version.) MAX8_ _R/S/T, VCC = 3.3V MAX8_ _Z, VCC = 2.5V 5 MAX8_ _L/M/R/S/T/Z, VCC = 1V 0 -40 -20 0 20 40 60 80 60 VOD = 20mV 40 VOD = 100mV 20 0 85 60 60 40 VOD = 100mV 20 0 VOD = 200mV -40 -20 20 0 40 TEMPERATURE (C) 1.003 NORMALIZED THRESHOLD MAX8_ _J/L/M 240 MAX8_ _R/S/T/Z 235 VOD = 20mV 80 60 85 NORMALIZED RESET THRESHOLD vs. TEMPERATURE MAX803-TOC5 245 VOD = 10mV 100 85 POWER-UP RESET TIMEOUT vs. TEMPERATURE 250 POWER-UP RESET TIMEOUT (s) 20 0 40 TEMPERATURE (C) VOD = VTH - VCC 120 VOD = 200mV -20 -40 TEMPERATURE (C) 230 225 MAX803-TOC3 VOD = 10mV 140 MAX803-TOC6 10 VOD = VTH - VCC POWER-DOWN RESET DELAY vs. TEMPERATURE (MAX8_ _J/L/M) POWER-DOWN RESET DELAY (s) MAX803 toc01 MAX8_ _L/M, VCC = 5V 100 POWER-DOWN RESET DELAY (s) SUPPLY CURRENT (A) 15 POWER-DOWN RESET DELAY vs. TEMPERATURE (MAX8_ _R/S/T/Z) MAX803-TOC4 SUPPLY CURRENT vs. TEMPERATURE (SC70 PACKAGE, NO LOAD) 1.002 1.001 1.000 0.999 0.998 -40 -20 0 20 40 TEMPERATURE (C) www.maximintegrated.com 60 85 0.997 -40 -20 0 20 40 60 85 TEMPERATURE (C) Maxim Integrated 4 MAX803/MAX809/ MAX810 3-Pin Microprocessor Reset Circuits Pin Configuration TOP VIEW GND 1 MAX803 MAX809 MAX810 3 VCC RESET (RESET) 2 SC70-3/SOT23-3 ( ) ARE FOR MAX810. MAX803 AVAILABLE IN SC70-3 ONLY. Ensuring a Valid Reset Output Down to VCC = 0V Pin Description PIN NAME 1 GND 3 FUNCTION Ground RESET (MAX803/ MAX809) RESET Output remains low while VCC is below the reset threshold, and for at least 140ms after VCC rises above the reset threshold. RESET (MAX810) RESET Output remains high while VCC is below the reset threshold, and for at least 140ms after VCC rises above the reset threshold. 2 VCC Supply Voltage (+5V, +3.3V, +3.0V, or +2.5V) Detailed Description A microprocessor's (P's) reset input starts the P in a known state. The MAX803/MAX809/MAX810 assert reset to prevent code-execution errors during power-up, powerdown, or brownout conditions. They assert a reset signal whenever the VCC supply voltage declines below a preset threshold, keeping it asserted for at least 140ms after VCC has risen above the reset threshold. The MAX803 uses an open-drain output, and the MAX809/MAX810 have a push-pull output stage. Connect a pullup resistor on the MAX803's RESET output to any supply between 0 and 6V. Applications Information Negative-Going VCC Transients In addition to issuing a reset to the P during power-up, power-down, and brownout conditions, the MAX803/ MAX809/MAX810 are relatively immune to short-duration negative-going VCC transients (glitches). Figure 1 shows typical transient duration vs. reset comparator overdrive, for which the MAX803/MAX809/ MAX810 do not generate a reset pulse. The graph was generated using a negative-going pulse applied www.maximintegrated.com to VCC, starting 0.5V above the actual reset threshold and ending below it by the magnitude indicated (reset comparator overdrive). The graph indicates the maximum pulse width a negative-going VCC transient can have without causing a reset pulse. As the magnitude of the transient increases (goes farther below the reset threshold), the maximum allowable pulse width decreases. Typically, for the MAX8__L and MAX8__M, a VCC transient that goes 100mV below the reset threshold and lasts 20s or less will not cause a reset pulse. A 0.1F bypass capacitor mounted as close as possible to the VCC pin provides additional transient immunity. When VCC falls below 1V, the MAX809 RESET output no longer sinks current--it becomes an open circuit. Therefore, high-impedance CMOS logic inputs connected to RESET can drift to undetermined voltages. This presents no problem in most applications since most P and other circuitry is inoperative with VCC below 1V. However, in applications where RESET must be valid down to 0V, adding a pull-down resistor to RESET causes any stray leakage currents to flow to ground, holding RESET low (Figure 2). R1's value is not critical; 100k is large enough not to load RESET and small enough to pull RESET to ground. A 100k pullup resistor to VCC is also recommended for the MAX810 if RESET is required to remain valid for VCC < 1V. Interfacing to Ps with Bidirectional Reset Pins Since the RESET output on the MAX803 is open drain, this device interfaces easily with Ps that have bidirectional reset pins, such as the Motorola 68HC11. Connecting the P supervisor's RESET output directly to the C's RESET pin with a single pullup resistor allows either device to assert reset (Figure 3). MAX803 Open-Drain RESET Output Allows Use with Multiple Supplies Generally, the pullup connected to the MAX803 will connect to the supply voltage that is being monitored at the IC's VCC pin. However, some systems may use the opendrain output to level-shift from the monitored supply to reset circuitry powered by some other supply (Figure 4). Note that as the MAX803's VCC decreases below 1V, so does the IC's ability to sink current at RESET. Also, with any pullup, RESET will be pulled high as VCC decays toward 0. The voltage where this occurs depends on the pullup resistor value and the voltage to which it is connected. Maxim Integrated 5 MAX803/MAX809/ MAX810 3-Pin Microprocessor Reset Circuits Benefits of Highly Accurate Reset Threshold Most P supervisor ICs have reset-threshold voltages between 5% and 10% below the value of nominal supply voltages. This ensures a reset will not occur within 5% of the nominal supply, but will occur when the supply is 10% below nominal. MAXIMUM TRANSIENT DURATION (s) 400 When using ICs rated at only the nominal supply 5%, this leaves a zone of uncertainty where the supply is between 5% and 10% low, and where the reset may or may not be asserted. The MAX8_ _L/T/Z use highly accurate circuitry to ensure that reset is asserted close to the 5% limit, and long before the supply has declined to 10% below nominal. VCC TA = +25C 320 VCC VCC P 240 MOTOROLA 68HCXX RESET INPUT MAX803 160 RESET MAX8_ _J/L/M 80 0 MAX8_ _R/S/T/Z 1 10 GND GND 100 1000 RESET COMPARATOR OVERDRIVE, VTH - VCC (mV) Figure 1. Maximum Transient Duration Without Causing a Reset Pulse vs. Reset Comparator Overdrive Figure 3. Interfacing to Ps with Bidirectional Reset I/O +5.0V +3.3V VCC VCC MAX809 RPULLUP RESET GND VCC MAX803 R1 100k Figure 2. RESET Valid to VCC = Ground Circuit RESET GND 5V SYSTEM RESET INPUT GND Figure 4. MAX803 Open-Drain RESET Output Allows Use with Multiple Supplies www.maximintegrated.com Maxim Integrated 6 MAX803/MAX809/ MAX810 3-Pin Microprocessor Reset Circuits Selector Guide RESET THRESHOLD (V) OUTPUT TYPE MAX803L PART/SUFFIX 4.63 Open-Drain RESET MAX803M 4.38 Open-Drain RESET MAX803T 3.08 Open-Drain RESET MAX803S 2.93 Open-Drain RESET MAX803R 2.63 Open-Drain RESET MAX803Z 2.32 Open-Drain RESET MAX809L 4.63 Push-Pull RESET MAX809M 4.38 Push-Pull RESET MAX809J 4.00 Push-Pull RESET MAX809T 3.08 Push-Pull RESET MAX809S 2.93 Push-Pull RESET MAX809R 2.63 Push-Pull RESET MAX809Z 2.32 Push-Pull RESET MAX810L 4.63 Push-Pull RESET MAX810M 4.38 Push-Pull RESET MAX810T 3.08 Push-Pull RESET MAX810S 2.93 Push-Pull RESET MAX810R 2.63 Push-Pull RESET MAX810Z 2.32 Push-Pull RESET For top mark information, go to https://www.maximintegrated.com/en/design/packaging/topmark/. Chip Information Ordering Information TRANSISTOR COUNT: 275 (SOT23) PART 380 (SC70) Package Information For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE PACKAGE CODE DOCUMENT NO. 3 SC70 X3+2, X3-2 21-0075 3 SOT23 U3+1, U3-1 21-0051 www.maximintegrated.com TEMP RANGE PIN-PACKAGE MAX803_EXR-T -40C to +125C 3 SC70 MAX803_EXR+T -40C to +125C 3 SC70 MAX803_EXR/V+ -40C to +125C 3 SC70 MAX803_EXR/V+T -40C to +125C 3 SC70 MAX809_EXR-T -40C to +125C 3 SC70 MAX809_EXR+T -40C to +125C 3 SC70 MAX809_EUR-T -40C to +105C 3 SOT23 MAX809_EUR+T -40C to +105C 3 SOT23 MAX810_EXR+T -40C to +125C 3 SC70 MAX810_EUR+T -40C to +105C 3 SOT23 Note: These parts are offered in 2.5k reels, and must be ordered in 2.5k increments. Insert the desired suffix letter from the Selector Guide into the blank to complete the part number. All versions of these products may not be available at the time of announcement. Contact factory for availability. Some devices are available in both leaded and lead-free packaging. +Denotes a lead(Pb)-free/RoHS-compliant package. /V denotes an automotive qualified part. T = Tape and reel. Maxim Integrated 7 MAX803/MAX809/ MAX810 3-Pin Microprocessor Reset Circuits Revision History REVISION NUMBER REVISION DATE PAGES CHANGED 0 12/94 Initial release. 7 2/10 Updated Ordering Information, added lead-free note, and added soldering temperature in the Absolute Maximum Ratings 8 12/12 Added MAX803_EXR/V+ to Ordering Information 9 6/15 Added MAX803_EXR/V+ to Ordering Information, moved Ordering Information, Pin Configuration, and Selector Guide to end of data sheet, and rebranded data sheet 1-8 10 12/15 Added lead-free package code information and removed top mark information from Selector Guide 7 DESCRIPTION -- 1, 2 1 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated's website at www.maximintegrated.com. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. (c) 2015 Maxim Integrated Products, Inc. 8 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: MAX803MEXR+T MAX803REXR+T MAX803SEXR+T MAX809LEUR+T MAX809MEUR+T MAX809REUR+T MAX809SEUR+T MAX809TEUR+T MAX809ZEXR+T MAX810LEUR+T MAX810SEUR+T MAX810TEUR+T MAX803LEXR+T MAX803LEXR+T10 MAX803MEXR+T10 MAX803REXR+T10 MAX803SEXR+T10 MAX803TEXR+T MAX803TEXR+T10 MAX803ZEXR+T MAX803ZEXR+T10 MAX809JEUR+T MAX809LEUR+T10 MAX809LEXR+T MAX809LEXR+T10 MAX809MEUR+T10 MAX809MEXR+T MAX809MEXR+T10 MAX809REUR+T10 MAX809REXR+T MAX809REXR+T10 MAX809SEUR+T10 MAX809SEXR+T MAX809SEXR+T10 MAX809TEUR+T10 MAX809TEXR+T MAX809TEXR+T10 MAX809ZEXR+T10 MAX810LEUR+T10 MAX810LEXR+T MAX810LEXR+T10 MAX810MEUR+T MAX810MEUR+T10 MAX810MEXR+T MAX810MEXR+T10 MAX810REUR+T MAX810REUR+T10 MAX810REXR+T MAX810REXR+T10 MAX810SEUR+T10 MAX810SEXR+T MAX810SEXR+T10 MAX810TEUR+T10 MAX810TEXR+T MAX810TEXR+T10 MAX810ZEXR+T MAX810ZEXR+T10 MAX367EWN+T MAX1609EEE+T