LP3892 www.ti.com SNVS236D - SEPTEMBER 2003 - REVISED APRIL 2013 LP3892 1.5A Fast-Response Ultra Low Dropout Linear Regulators Check for Samples: LP3892 FEATURES DESCRIPTION * The LP3892 is a high current, fast response regulator which can maintain output voltage regulation with minimum input to output voltage drop. Fabricated on a CMOS process, the device operates from two input voltages: Vbias provides voltage to drive the gate of the N-MOS power transistor, while Vin is the input voltage which supplies power to the load. The use of an external bias rail allows the part to operate from ultra low Vin voltages. Unlike bipolar regulators, the CMOS architecture consumes extremely low quiescent current at any output load current. The use of an N-MOS power transistor results in wide bandwidth, yet minimum external capacitance is required to maintain loop stability. 1 2 * * * * * * * Ultra Low Dropout Voltage (140 mV at 1.5A typ) Low Ground Pin Current Load Regulation of 0.04%/A 60 nA Typical Quiescent Current in Shutdown 1.5% Output Accuracy (25C) TO-220, DDPAK/TO-263 and SO PowerPAD-8 Packages Over Temperature/Over Current Protection -40C to +125C Junction Temperature Range APPLICATIONS * * * * * * * DSP Power Supplies Server Core and I/O Supplies PC Add-in-Cards Local Regulators in Set-Top Boxes Microcontroller Power Supplies High Efficiency Power Supplies SMPS Post-Regulators The fast transient response of these devices makes them suitable for use in powering DSP, Microcontroller Core voltages and Switch Mode Power Supply post regulators. The parts are available in TO-220, DDPAK/TO-263 and SO PowerPAD-8 packages. Dropout Voltage:140mV (typ) at 1.5A load current. Ground Pin Current: 3 mA (typ) at full load. Shutdown Current: 60 nA (typ) when S/D pin is low. Precision Output Voltage: 1.5% room temperature accuracy. TYPICAL APPLICATION CIRCUIT At least 10 F of input and output capacitance is required for stability. *Tantalum capacitors are recommended. Aluminum electrolytic capacitors may be used for restricted temperature range. See application hints. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2003-2013, Texas Instruments Incorporated LP3892 SNVS236D - SEPTEMBER 2003 - REVISED APRIL 2013 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. CONNECTION DIAGRAM Figure 1. TO-220, Top View Figure 2. DDPAK/TO-263, Top View VOUT 1 VOUT 2 VBIAS 3 GND 4 GND 8 N/C 7 VIN 6 S/D 5 GND Figure 3. SO PowerPAD-8, Top View white space white space white space white space BLOCK DIAGRAM 2 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LP3892 LP3892 www.ti.com SNVS236D - SEPTEMBER 2003 - REVISED APRIL 2013 ABSOLUTE MAXIMUM RATINGS (1) VALUE / UNITS -65C to +150C Storage Temperature Range Lead Temp. (Soldering, 5 seconds) 260C ESD Rating Human Body Model Machine Model (3) 2 kV 200V Power Dissipation (2) (4) Internally Limited VIN Supply Voltage (Survival) -0.3V to +6V VBIAS Supply Voltage (Survival) -0.3V to +7V -0.3V to +7V Shutdown Input Voltage (Survival) IOUT (Survival) Internally Limited -0.3V to +6V Output Voltage (Survival) -40C to +150C Junction Temperature (1) (2) (3) (4) Absolute maximum ratings indicate limits beyond which damage to the component may occur. Operating ratings indicate conditions for which the device is intended to be functional, but do not ensure specific performance limits. For specifications, see Electrical Characteristics. Specifications do not apply when operating the device outside of its rated operating conditions. The human body model is a 100 pF capacitor discharged through a 1.5k resistor into each pin. The machine model is a 220 pF capacitor discharged directly into each pin. The machine model ESD rating of pin 5 is 100V. At elevated temperatures, device power dissipation must be derated based on package thermal resistance and heatsink thermal values. J-A for TO-220 devices is 65C/W if no heatsink is used. If the TO-220 device is attached to a heatsink, a J-S value of 4C/W can be assumed. J-A for DDPAK/TO-263 devices is approximately 40C/W if soldered down to a copper plane which is at least 1.5 square inches in area. J-A value for typical SO PowerPAD-8 PC board mounting is 166C/W. If power dissipation causes the junction temperature to exceed specified limits, the device will go into thermal shutdown. RECOMMENDED OPERATING CONDITIONS VALUE / UNITS VIN (VOUT + VDO) to 5.5V Shutdown 0 to +6V IOUT 1.5A -40C to +125C Junction Temperature VBIAS 4.5V to 6V Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LP3892 3 LP3892 SNVS236D - SEPTEMBER 2003 - REVISED APRIL 2013 www.ti.com ELECTRICAL CHARACTERISTICS Limits in standard typeface are for TJ = 25C, and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: VIN = VO(NOM) + 1V, VBIAS = 4.5V, IL = 10 mA, CIN = COUT = 10F, VS/D = VBIAS. Symbol VO Parameter Conditions 10 mA IL 1.5A, VO(NOM) + 1V VIN 5.5V, 4.5V VBIAS 6V Output Voltage Tolerance VO/VIN Output Voltage Line Regulation (3) VO/IL Output Voltage Load Regulation VDO Dropout Voltage IQ(VIN) MIN (4) (5) (6) Quiescent Current Drawn from VIN Supply (1) ISC Quiescent Current Drawn from VBIAS Supply Short-Circuit Current (2) MAX (1) 1.198 1.186 1.216 1.234 1.246 1.478 1.455 1.5 1.522 1.545 1.773 1.746 1.8 1.827 1.854 Units V VO(NOM) + 1V VIN 5.5V 0.01 %/V 10 mA IL 1.5A 0.04 0.06 %/A IL = 1.5A (TO-220 and DDPAK/TO-263 only) 140 320 500 IL = 1.5A (SO PowerPAD only) 155 340 550 3 7 8 mA 0.03 1 30 A 1 2 3 mA VS/D 0.3V 0.03 1 30 A VOUT = 0V 4.3 10 mA IL 1.5A VS/D 0.3V IQ(VBIAS) Typical 10 mA IL 1.5A mV A Shutdown Input VSDT Output Turn-off Threshold Output = ON 1.3 0.7 Output = OFF 0.7 Td (OFF) Turn-OFF Delay RLOAD X COUT << Td (OFF) 20 Td (ON) Turn-ON Delay RLOAD X COUT << Td (ON) 15 IS/D S/D Input Current VS/D =1.3V 1 VS/D 0.3V -1 0.3 V s A AC Parameters PSRR (VIN) Ripple Rejection for VIN Input Voltage VIN = VOUT +1V, f = 120 Hz PSRR (VBIAS) Ripple Rejection for VBIAS Voltage en (1) (2) (3) (4) (5) (6) 4 80 VIN = VOUT + 1V, f = 1 kHz 65 VBIAS = VOUT + 3V, f = 120 Hz 70 VBIAS = VOUT + 3V, f = 1 kHz 65 Output Noise Density f = 120 Hz Output Noise Voltage BW = 10 Hz - 100 kHz, VOUT = 1.8V 150 BW = 300 Hz - 300 kHz, VOUT = 1.8V 90 1 dB V/root- Hz V (rms) Limits are specified through testing, statistical correlation, or design. Typical numbers represent the most likely parametric norm for 25C operation. If used in a dual-supply system where the regulator load is returned to a negative supply, the output pin must be diode clamped to ground. Output voltage line regulation is defined as the change in output voltage from nominal value resulting from a change in input voltage. Output voltage load regulation is defined as the change in output voltage from nominal value as the load current increases from no load to full load. Dropout voltage is defined as the minimum input to output differential required to maintain the output with 2% of nominal value. The SO PowerPAD-8 package devices have a slightly higher dropout voltage due to increased band wire resistance. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LP3892 LP3892 www.ti.com SNVS236D - SEPTEMBER 2003 - REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS Unless otherwise specified: TJ = 25C, COUT = 10 F, Cin = 10 F, S/D pin is tied to VBIAS, VIN = 2.2V, VOUT = 1.8V. IGND vs VSD VOUT vs Temperature Figure 4. Figure 5. DC Load Regulation Line Regulation vs VIN Figure 6. Figure 7. Line Regulation vs VBIAS IBIAS vs IL 1.60 VBIAS = 5V VIN = 2.3V IBIAS (mA) 1.40 125oC 1.20 25oC 1.00 -40oC 0.80 0.60 0 0.5 1.0 1.5 LOAD CURRENT (A) Figure 8. Figure 9. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LP3892 5 LP3892 SNVS236D - SEPTEMBER 2003 - REVISED APRIL 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) Unless otherwise specified: TJ = 25C, COUT = 10 F, Cin = 10 F, S/D pin is tied to VBIAS, VIN = 2.2V, VOUT = 1.8V. 6 IGND vs VSD Noise Measurement Figure 10. Figure 11. VOUTStartup Waveform VOUTStartup Waveform Figure 12. Figure 13. Line Regulation vs VBIAS Line Regulation vs VBIAS Figure 14. Figure 15. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LP3892 LP3892 www.ti.com SNVS236D - SEPTEMBER 2003 - REVISED APRIL 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Unless otherwise specified: TJ = 25C, COUT = 10 F, Cin = 10 F, S/D pin is tied to VBIAS, VIN = 2.2V, VOUT = 1.8V. VIN PSRR VIN PSRR Figure 16. Figure 17. VBIAS PSRR Figure 18. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LP3892 7 LP3892 SNVS236D - SEPTEMBER 2003 - REVISED APRIL 2013 www.ti.com Application Hints EXTERNAL CAPACITORS To assure regulator stability, input and output capacitors are required as shown in the Typical Application Circuit. OUTPUT CAPACITOR At least 10F of output capacitance is required for stability (the amount of capacitance can be increased without limit). The output capacitor must be located less than 1 cm from the output pin of the IC and returned to a clean analog ground. The ESR (equivalent series resistance) of the output capacitor must be within the "stable" range as shown in Figure 19 over the full operating temperature range for stable operation. 10 COUT ESR (:) 1.0 COUT > 10 PF STABLE REGION 0.1 .01 .001 0 1 LOAD CURRENT (A) 2 Figure 19. Minimum ESR vs Output Load Current Tantalum capacitors are recommended for the output as their ESR is ideally suited to the part's requirements and the ESR is very stable over temperature. Aluminum electrolytics are not recommended because their ESR increases very rapidly at temperatures below 10C. Aluminum caps can only be used in applications where lower temperature operation is not required. A second problem with Al caps is that many have ESR's which are only specified at low frequencies. The typical loop bandwidth of a linear regulator is a few hundred kHz to several MHz. If an Al cap is used for the output cap, it must be one whose ESR is specified at a frequency of 100 kHz or more. Because the ESR of ceramic capacitors is only a few milliohms, they are not suitable for use as output capacitors on LP389X devices. The regulator output can tolerate ceramic capacitance totaling up to 15% of the amount of Tantalum capacitance connected from the output to ground. INPUT CAPACITOR The input capacitor must be at least 10 F, but can be increased without limit. It's purpose is to provide a low source impedance for the regulator input. Ceramic capacitors work best for this, but Tantalums are also very good. There is no ESR limitation on the input capacitor (the lower, the better). Aluminum electrolytics can be used, but their ESR increase very quickly at cold temperatures. They are not recommended for any application where temperatures go below about 10C. BIAS CAPACITOR The 0.1F capacitor on the bias line can be any good quality capacitor (ceramic is recommended). BIAS VOLTAGE The bias voltage is an external voltage rail required to get gate drive for the N-FET pass transistor. Bias voltage must be in the range of 4.5 - 6V to assure proper operation of the part. UNDER VOLTAGE LOCKOUT The bias voltage is monitored by a circuit which prevents the regulator output from turning on if the bias voltage is below approximately 4V. 8 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LP3892 LP3892 www.ti.com SNVS236D - SEPTEMBER 2003 - REVISED APRIL 2013 SHUTDOWN OPERATION Pulling down the shutdown (S/D) pin will turn-off the regulator. Pin S/D must be actively terminated through a pull-up resistor (10 k to 100 k) for a proper operation. If this pin is driven from a source that actively pulls high and low (such as a CMOS rail to rail comparator), the pull-up resistor is not required. This pin must be tied to Vin if not used. POWER DISSIPATION/HEATSINKING A heatsink may be required depending on the maximum power dissipation and maximum ambient temperature of the application. Under all possible conditions, the junction temperature must be within the range specified under operating conditions. The total power dissipation of the device is given by: PD = (VIN-VOUT)IOUT+ (VIN)IGND (1) where IGND is the operating ground current of the device. The maximum allowable temperature rise (TRmax) depends on the maximum ambient temperature (TAmax) of the application, and the maximum allowable junction temperature (TJmax): TRmax = TJmax- TAmax (2) The maximum allowable value for junction to ambient Thermal Resistance, JA, can be calculated using the formula: JA = TRmax / PD (3) These parts are available in TO-220 and DDPAK/TO-263 packages. The thermal resistance depends on amount of copper area or heat sink, and on air flow. If the maximum allowable value of JA calculated above is 60 C/W for TO-220 package and 60 C/W for DDPAK/TO-263 package no heatsink is needed since the package can dissipate enough heat to satisfy these requirements. If the value for allowable JA falls below these limits, a heat sink is required. HEATSINKING TO-220 PACKAGE The thermal resistance of a TO-220 package can be reduced by attaching it to a heat sink or a copper plane on a PC board. If a copper plane is to be used, the values of JA will be same as shown in next section for DDPAK/TO-263 package. The heatsink to be used in the application should have a heatsink to ambient thermal resistance, HA JA - CH - JC. In this equation, CH is the thermal resistance from the case to the surface of the heat sink and JC is the thermal resistance from the junction to the surface of the case. JC is about 3C/W for a TO-220 package. The value for CH depends on method of attachment, insulator, etc. CH varies between 1.5C/W to 2.5C/W. If the exact value is unknown, 2C/W can be assumed. HEATSINKING DDPAK/TO-263 PACKAGE The DDPAK/TO-263 package uses the copper plane on the PCB as a heatsink. The tab of these packages are soldered to the copper plane for heat sinking. The graph below shows a curve for the JA of DDPAK/TO-263 package for different copper area sizes, using a typical PCB with 1 ounce copper and no solder mask over the copper area for heat sinking. Figure 20. JA vs Copper (1 Ounce) Area for DDPAK/TO-263 Package Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LP3892 9 LP3892 SNVS236D - SEPTEMBER 2003 - REVISED APRIL 2013 www.ti.com As shown in the graph below, increasing the copper area beyond 1 square inch produces very little improvement. The minimum value for JA for the DDPAK/TO-263 package mounted to a PCB is 32C/W. Figure 22 shows the maximum allowable power dissipation for DDPAK/TO-263 packages for different ambient temperatures, assuming JA is 35C/W and the maximum junction temperature is 125C. Figure 21. Maximum Power Dissipation vs Ambient Temperature for DDPAK/TO-263 Package HEATSINKING SO PowerPAD PACKAGE Heatsinking for the SO PowerPAD-8 package is accomplished by allowing heat to flow through the ground slug on the bottom of the package into the copper on the PC board. The heat slug must be soldered down to a copper plane to get good heat transfer. It can also be connected through vias to internal copper planes. Since the heat slug is at ground potential, traces must not be routed under it which are not at ground potential. Under all possible conditions, the junction temperature must be within the range specified under operating conditions. Figure 22 shows a curve for the JA of the SO PowerPAD package for different copper area sizes using a typical PCB with one ounce copper in still air. QJA (oC/W) 180 130 80 30 0 0.5 1 1.5 COPPER AREA (sq. in.) Figure 22. JA vs Copper (1 ounce) Area for SO PowerPAD Package 10 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LP3892 LP3892 www.ti.com SNVS236D - SEPTEMBER 2003 - REVISED APRIL 2013 REVISION HISTORY Changes from Revision C (April 2013) to Revision D * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 10 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LP3892 11 PACKAGE OPTION ADDENDUM www.ti.com 13-Sep-2014 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LP3892EMR-1.2/NOPB ACTIVE SO PowerPAD DDA 8 95 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 3892E MR1.2 LP3892EMR-1.5/NOPB ACTIVE SO PowerPAD DDA 8 95 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 3892E MR1.5 LP3892EMR-1.8/NOPB ACTIVE SO PowerPAD DDA 8 95 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 3892E MR1.8 LP3892EMRX-1.2/NOPB ACTIVE SO PowerPAD DDA 8 2500 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 3892E MR1.2 LP3892EMRX-1.5/NOPB ACTIVE SO PowerPAD DDA 8 2500 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 3892E MR1.5 LP3892ES-1.2/NOPB ACTIVE DDPAK/ TO-263 KTT 5 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3892ES -1.2 LP3892ES-1.5/NOPB ACTIVE DDPAK/ TO-263 KTT 5 45 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3892ES -1.5 LP3892ESX-1.2/NOPB ACTIVE DDPAK/ TO-263 KTT 5 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3892ES -1.2 LP3892ESX-1.5/NOPB ACTIVE DDPAK/ TO-263 KTT 5 500 Pb-Free (RoHS Exempt) CU SN Level-3-245C-168 HR -40 to 125 LP3892ES -1.5 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 13-Sep-2014 (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LP3892EMRX-1.2/NOPB SO Power PAD DDA 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LP3892EMRX-1.5/NOPB SO Power PAD DDA 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LP3892ESX-1.2/NOPB DDPAK/ TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 LP3892ESX-1.5/NOPB DDPAK/ TO-263 KTT 5 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP3892EMRX-1.2/NOPB SO PowerPAD DDA 8 2500 367.0 367.0 35.0 LP3892EMRX-1.5/NOPB SO PowerPAD DDA 8 2500 367.0 367.0 35.0 LP3892ESX-1.2/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 LP3892ESX-1.5/NOPB DDPAK/TO-263 KTT 5 500 367.0 367.0 45.0 Pack Materials-Page 2 PACKAGE OUTLINE DDA0008B PowerPAD TM SOIC - 1.7 mm max height SCALE 2.400 PLASTIC SMALL OUTLINE C 6.2 TYP 5.8 A SEATING PLANE PIN 1 ID AREA 0.1 C 6X 1.27 8 1 2X 3.81 5.0 4.8 NOTE 3 4 5 8X B 4.0 3.8 NOTE 4 0.51 0.31 0.25 1.7 MAX C A B 0.25 TYP 0.10 SEE DETAIL A 5 4 EXPOSED THERMAL PAD 3.4 2.8 0.25 GAGE PLANE 9 8 1 0 -8 0.15 0.00 1.27 0.40 DETAIL A 2.71 2.11 TYPICAL 4214849/A 08/2016 PowerPAD is a trademark of Texas Instruments. NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm per side. 4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side. 5. Reference JEDEC registration MS-012. www.ti.com EXAMPLE BOARD LAYOUT DDA0008B PowerPAD TM SOIC - 1.7 mm max height PLASTIC SMALL OUTLINE (2.95) NOTE 9 SOLDER MASK DEFINED PAD (2.71) SOLDER MASK OPENING SEE DETAILS 8X (1.55) 1 8 8X (0.6) 9 SYMM (1.3) TYP (3.4) SOLDER MASK OPENING (4.9) NOTE 9 6X (1.27) 5 4 (R0.05) TYP METAL COVERED BY SOLDER MASK SYMM ( 0.2) TYP VIA (1.3) TYP (5.4) LAND PATTERN EXAMPLE SCALE:10X 0.07 MIN ALL AROUND 0.07 MAX ALL AROUND SOLDER MASK OPENING METAL SOLDER MASK OPENING METAL UNDER SOLDER MASK SOLDER MASK DEFINED NON SOLDER MASK DEFINED SOLDER MASK DETAILS PADS 1-8 4214849/A 08/2016 NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site. 8. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature numbers SLMA002 (www.ti.com/lit/slma002) and SLMA004 (www.ti.com/lit/slma004). 9. Size of metal pad may vary due to creepage requirement. 10. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown on this view. It is recommended that vias under paste be filled, plugged or tented. www.ti.com EXAMPLE STENCIL DESIGN DDA0008B PowerPAD TM SOIC - 1.7 mm max height PLASTIC SMALL OUTLINE (2.71) BASED ON 0.125 THICK STENCIL 8X (1.55) (R0.05) TYP 1 8 8X (0.6) (3.4) BASED ON 0.125 THICK STENCIL 9 SYMM 6X (1.27) 5 4 METAL COVERED BY SOLDER MASK SYMM (5.4) SEE TABLE FOR DIFFERENT OPENINGS FOR OTHER STENCIL THICKNESSES SOLDER PASTE EXAMPLE EXPOSED PAD 100% PRINTED SOLDER COVERAGE BY AREA SCALE:10X STENCIL THICKNESS SOLDER STENCIL OPENING 0.1 0.125 0.150 0.175 3.03 X 3.80 2.71 X 3.40 (SHOWN) 2.47 X 3.10 2.29 X 2.87 4214849/A 08/2016 NOTES: (continued) 11. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 12. Board assembly site may have different recommendations for stencil design. www.ti.com MECHANICAL DATA KTT0005B TS5B (Rev D) BOTTOM SIDE OF PACKAGE www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2018, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LP3892EMR-1.2 LP3892EMR-1.2/NOPB LP3892EMR-1.5 LP3892EMR-1.5/NOPB LP3892EMR-1.8 LP3892EMR1.8/NOPB LP3892EMRX-1.2 LP3892EMRX-1.2/NOPB LP3892EMRX-1.5 LP3892EMRX-1.5/NOPB LP3892ES-1.2 LP3892ES-1.2/NOPB LP3892ES-1.5 LP3892ES-1.5/NOPB LP3892ESX-1.2 LP3892ESX-1.2/NOPB LP3892ESX-1.5 LP3892ESX-1.5/NOPB