Part Number 440GX
Revision 1.19 – December 19, 2008
AMCC 1
440GX
Power PC 440GX Embedded Processor
Data Sheet
Features
•PowerPC
® 440 processor core operating up to
800MHz with 32KB I- and D-caches (with parity
checking)
• On-chip 256KB SRAM configurable as L2 Code
store or Ethernet Packet store memory
• Selectable processor:bus clock ratios (Refer to
the Clocking chapter in the PPC440GX
Embedded Processor User’s Manual for details)
• Double Data Rate (DDR) Synchronous DRAM
(SDRAM) interface operating up to 166MHz
(200MHz for 800MHz Rev F parts)
• External Peripheral Bus (32 bits) for up to eight
devices with external mastering
• DMA support for external peripherals, internal
UART and memory
• PCI-X V1.0a interface (32 or 64 bits, up to
133MHz) with support for conventional PCI V2.3
• Two Ethernet 10/100/1000Mbps half- or full-
duplex interfaces. Operational modes supported
are SMII, GMII, RGMII, TBI and RTBI.
• TCP/IP Acceleration Hardware (TAH) provided for
10/100/1000 Mbps ports that performs checksum
processing, TCP segmentation, and includes
support for jumbo frames
• Programmable Interrupt Controller supports
interrupts from a variety of sources.
• I2O Messaging unit for message transfer between
the CPU and PCI-X
• Programmable General Purpose Timers (GPT)
• Two serial ports (16750 compatible UART)
• Two IIC interfaces
• General Purpose I/O (GPIO) interface available
• JTAG interface for board level testing
• Processor can boot from PCI memory
• Available in ceramic (RoHs and non-RoHS
compliant versions) and plastic packages (RoHS
and non-RoHS compliant versions).
Description
Designed specifically to address high-end embedded
applications, the PowerPC 440GX (PPC440GX)
provides a high-performance, low power solution that
interfaces to a wide range of peripherals by
incorporating on-chip power management features
and lower power dissipation.
This chip contains a high-performance RISC
processor core, DDR SDRAM controller, configurable
256KB SRAM to be used as L2 cache or software-
controlled on-chip memory, PCI-X bus interface,
Gigabit Ethernet interfaces, TCP/IP acceleration
hardware, I2O messaging unit, control for external
ROM and peripherals, DMA with scatter-gather
support, serial ports, IIC interface, and general
purpose I/O.
Technology: CMOS Cu-11, 0.13μm
Packages: 25mm, 552-ball Ceramic Ball Grid Array
(CBGA) or Plastic Ball Grid Array (PBGA) in standard
or RoHS compliant versions
Power (estimated): Less than:
4W typical @533MHz
5W typical @667MHz
6W typical @800MHz (estimated)
Supply voltages required: 3.3V, 2.5V, 1.5V
440GX – Power PC 440GX Embedded Processor
2 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Contents
Ordering and PVR Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Address Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PowerPC 440 Processor Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Internal Buses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PCI-X Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
DDR SDRAM Memory Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
On-Chip SRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
External Peripheral Bus Controller (EBC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Ethernet Controller Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
DMA Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
IIC Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
General Purpose Timers (GPT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
General Purpose IO (GPIO) Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Universal Interrupt Controller (UIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
PLB Performance Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
I2O Messaging Unit (IMU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
JTAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Signal Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Heat Sink Mounting Information (Ceramic Package Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Spread Spectrum Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
DDR SDRAM I/O Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
DDR SDRAM Write Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
DDR SDRAM Read Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Strapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Serial EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
440GX – Power PC 440GX Embedded Processor
AMCC 3
Revision 1.19 – December 19, 2008
Data Sheet
Figures
PPC440GX Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
25mm, 552-Ball Ceramic (CBGA) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
25mm, 552-Ball Plastic (FC-PBGA) Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Heat Sink Attached With Spring Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Heat Sink Attached With Adhesive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Timing Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Input Setup and Hold Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Output Delay and Float Timing Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
DDR SDRAM Simulation Signal Termination Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
DDR SDRAM Write Cycle Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
DDR SDRAM MemClkOut0 and Read Clock Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
DDR SDRAM Read Data Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
DDR SDRAM Read Cycle Timing—Example 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
DDR SDRAM Read Cycle Timing—Example 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
DDR SDRAM Read Cycle Timing—Example 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Tables
Order Part Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
System Memory Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
DCR Address Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Signals Listed Alphabetically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Signals Listed by Ball Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Pin Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Signal Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Package Thermal Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Recommended DC Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Input Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
DC Power Supply Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Clocking Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Peripheral Interface Clock Timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
I/O Specifications—All Speeds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
I/O Specifications—500MHz–800MHz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
DDR SDRAM Output Driver Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
I/O Timing—DDR SDRAM TDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
I/O Timing—DDR SDRAM TSK, TSA, and THA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
I/O Timing—DDR SDRAM TSD and THD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
I/O Timing—DDR SDRAM TSIN and TDIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Strapping Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
440GX – Power PC 440GX Embedded Processor
4 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Ordering and PVR Information
For information on the availability of the following parts, contact your local AMCC sales office.
Order Part Numbers
Product
Name
Order Part Number
(See Notes and Key drawing)
Processor
Frequency Package Rev
Level PVR Value JTAG ID
PPC440GX PPC440GX-3CC533S 533MHz 25mm, 552 CBGA C 0x51B21892 0x32054049
PPC440GX PPC440GX-3CC667S 667MHz 25mm, 552 CBGA C 0x51B21892 0x32054049
PPC440GX PPC440GX-3CF400C 400MHz 25mm, 552 CBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3CF533C 533MHz 25mm, 552 CBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3CF533CZ 533MHz 25mm, 552 CBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3CF533E 533MHz 25mm, 552 CBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3CF667C 667MHz 25mm, 552 CBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3CF667CZ 667MHz 25mm, 552 CBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3CF800C 800MHz 25mm, 552 CBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3CF800CZ 800MHz 25mm, 552 CBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3FF533C 533MHz 25mm, 552 PBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3FF533E 533MHz 25mm, 552 PBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3FF667C 667MHz 25mm, 552 PBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3FF667E 667MHz 25mm, 552 PBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3RF400C 400MHz 25mm, 552 CBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3RF533C 533MHz 25mm, 552 CBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3RF533CZ 533MHz 25mm, 552 CBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3RF533E 533MHz 25mm, 552 CBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3RF667C 667MHz 25mm, 552 CBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3RF667CZ 667MHz 25mm, 552 CBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3RF800C 800MHz 25mm, 552 CBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3RF800CZ 800MHz 25mm, 552 CBGA F 0x51B21894 0x52054049
440GX – Power PC 440GX Embedded Processor
AMCC 5
Revision 1.19 – December 19, 2008
Data Sheet
Each part number contains a revision code. This is the die mask revision number and is included in the part
number for identification purposes only.
The PVR (Processor Version Register) and the JTAG ID register are software accessible (read-only) and contain
information that uniquely identifies the part. Refer to the PPC440GX User’s Manual for details on accessing these
registers.
Order Part Number Key
PPC440GX PPC440GX-3NF533C 533MHz 25mm, 552 PBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3NF533E 533MHz 25mm, 552 PBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3NF667C 667MHz 25mm, 552 PBGA F 0x51B21894 0x52054049
PPC440GX PPC440GX-3NF667E 667MHz 25mm, 552 PBGA F 0x51B21894 0x52054049
Notes:
1. Package code: C = leaded ceramic, F = plastic, R = reduced-lead ceramic (RoHS compliant), N = lead-free plastic (RoHS compliant).
2. Case Temperature Range code: C = -40 °C to +85 °C, E = -40 °C to +105 °C for C package and -40 °C to +100 °C for F package, S = -
40 °C to +85 °C and no L2 cache support.
3. Z at the end of the Order Part Number indicates a tape-and-reel shipping package. Otherwise, the chips are shipped in a tray.
4. Revision code: C = rev 2.1, F = rev 3.1.
Order Part Numbers (Continued)
Product
Name
Order Part Number
(See Notes and Key drawing)
Processor
Frequency Package Rev
Level PVR Value JTAG ID
Part Number
PPC440GX-3CC800Ex
Package
Processor Speed
Grade 3 Reliability
Case Temperature Range
Revision Level
Shipping Package
440GX – Power PC 440GX Embedded Processor
6 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
PPC440GX Functional Block Diagram
The PPC440GX is designed using the IBM® Microelectronics Blue Logic™ methodology in which major functional
blocks are integrated together to create an application-specific product (ASIC). This approach provides a
consistent way to create complex ASICs using IBM CoreConnect Bus™ Architecture.
Note: IBM CoreConnect buses provide:
• 128-bit PLB interfaces up to 200MHz
• 32-bit OPB interfaces up to 83.33MHz, 333MB/s
Address Maps
The PPC440GX incorporates two address maps. The first is a fixed processor system memory address map. This
address map defines the possible contents of various address regions which the processor can access. The
second address map is for Device Configuration Registers (DCRs). The DCRs are accessed by software running
on the PPC440GX processor through the use of mtdcr and mfdcr instructions.
Processor Core DCR Bus
32KB On-chip Peripheral Bus (OPB)
GPIO IIC UART
DMA
Bridge
Processor Local Bus (PLB)
DDR SDRAM
External
Bus
Controller
Controller
Clock
Control
Reset
Power
Mgmt
JTAG Trace
Timers
MMU
Controller OPB
Interrupt
Controller
Arb
32-bit addr
32-bit data
13-bit addr
32/64-bit data
External
Bus Master
Controller
Universal
I-Cache
32KB
D-Cache
(4-Channel)
SRAM
256KB
PPC440
63 internal
18 external
PCI-X
Bridge
x2 x2
MAL
Ethernet
x2
DCRs
1 GMII
or
2 RGMII
or
1 TBI
or
2 RTBI
GP
Timers
1 MII
or
2 RMII
or
4 SMII
ZMII
RGMII
I2O
Messaging
83MHz max
L2 Controller
10/100
TAH
10/100/
1000 x2
133MHz max 166MHz max
Bridge Bridge
32/64-bit data
440GX – Power PC 440GX Embedded Processor
AMCC 7
Revision 1.19 – December 19, 2008
Data Sheet
System Memory Address Map (Sheet 1 of 2)
Function Sub Function Start Address End Address Size
Local Memory1
DDR SDRAM 0 0000 0000 0 7FFF FFFF 2GB
SRAM 0 8000 0000 0 8000 3FFF 256KB
Reserve 0 8000 4000 0 FFFE FFFF
IMU 0 FFFF 0000 0 FFFF FFFF 64KB
Internal Peripherals
EBC 1 0000 0000 1 3FFF FFFF 1GB
Reserved 1 4000 0000 1 4000 01FF
UART0 1 4000 0200 1 4000 0207 8B
Reserved 1 4000 0208 1 4000 02FF
UART1 1 4000 0300 1 4000 0307 8B
Reserved 1 4000 0308 1 4000 03FF
IIC0 1 4000 0400 1 4000 041F 32B
Reserved 1 4000 0420 1 4000 04FF
IIC1 1 4000 0500 1 4000 051F 32B
Reserved 1 4000 0520 1 4000 05FF
OPB Arbiter 1 4000 0600 1 4000 063F 64B
Reserved 1 4000 0640 1 4000 06FF
GPIO Controller 1 4000 0700 1 4000 077F 128B
Ethernet PHY ZMII 1 4000 0780 1 4000 078F 16B
Ethernet PHY GMII 1 4000 0790 1 4000 079F 16B
Reserved 1 4000 07A0 1 4000 07FF
Ethernet 0 Controller 1 4000 0800 1 4000 08FF 256B
Ethernet 1 Controller 1 4000 0900 1 4000 09FF 256B
General Purpose Timer 1 4000 0A00 1 4000 0AFF 256B
TCPIP Accelerator 0 1 4000 0B00 1 4000 0BFF 256B
Ethernet 2 Controller 1 4000 0C00 1 4000 0CFF 256B
TCPIP Accelerator 1 1 4000 0D00 1 4000 0DFF 256B
Ethernet 3 Controller 1 4000 0E00 1 4000 0EFF 256B
Reserved 1 4000 0F00 1 EFFF FFFF
Expansion ROM21 F000 0000 1 FFDF FFFF 254MB
Boot ROM2, 3 1 FFE0 0000 1 FFFF FFFF 2MB
440GX – Power PC 440GX Embedded Processor
8 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
PCI-X
Reserved 2 0000 0000 2 07FF FFFF
PCI-X I/O 2 0800 0000 2 0BFF FFFF 64MB
Reserved 2 0C00 0000 2 0EBF FFFF
PCI-X External Configuration Registers 2 0EC0 0000 2 0EC0 0007 8B
Reserved 2 0EC0 0008 2 0EC7 FFFF
PCI-X Bridge Core Configuration Registers 2 0EC8 0000 2 0EC8 00FF 256B
Reserved 2 0EC8 0100 2 0EC8 00FF
PCI-X Special Cycle 2 0ED0 0000 2 0EDF FFFF 1MB
PCI-X Memory 2 0EE0 0000 F FFFF FFFF 55.76 GB
Notes:
1. DDR SDRAM and on-chip SRAM can be located anywhere in the Local Memory area of the memory map.
2. The Boot ROM and Expansion ROM areas of the memory map are intended for use by ROM or Flash-type devices. While locating
volatile DDR SDRAM and SRAM in this region is supported, use of these regions for this purpose is not recommended.
3. When the optional boot from PCI-X memory is selected, the PCI-X Boot ROM address space begins at 2 FFFE 0000 (128 KB).
System Memory Address Map (Sheet 2 of 2)
Function Sub Function Start Address End Address Size
440GX – Power PC 440GX Embedded Processor
AMCC 9
Revision 1.19 – December 19, 2008
Data Sheet
DCR Address Map 4KB of Device Configuration Registers
Function Start Address End Address Size
Total DCR Address Space1000 3FF 1KW (4KB)1
By function:
Reserved 000 00B 12W
Clocking Power On Reset 00C 00D 2W
System DCRs 00E 00F 2W
Memory Controller 010 011 2W
External Bus Controller 012 013 2W
External Bus Master I/F 014 015 2W
PLB Performance Monitor 016 01F 10W
SRAM 020 02F 16W
L2 Controller 030 03F 16W
Reserved 040 07F 64W
PLB 080 08F 16W
PLB to OPB Bridge Out 090 09F 16W
Reserved 0A0 0A7 8W
OPB to PLB Bridge In 0A8 0AF 8W
Power Management 0B0 0B7 8W
Reserved 0B8 0BF 8W
Interrupt Controller 0 0C0 0CF 16W
Interrupt Controller 1 0D0 0DF 16W
Clock, Control, and Reset 0E0 0EF 16W
Reserved 0F0 0FF 16W
DMA Controller 100 13F 64W
Reserved 140 17F 64W
Ethernet MAL 180 1FF 128W
Base Interrupt Controller 200 20F 16W
Interrupt Controller 2 210 21F 16W
Reserved 220 3FF 480W
Notes:
1. DCR address space is addressable with up to 10 bits (1024 or 1K unique addresses). Each unique address represents a single 32-bit
(word) register. One kiloword (1024W) equals 4KB (4096 bytes).
440GX – Power PC 440GX Embedded Processor
10 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
PowerPC 440 Processor Core
The PowerPC 440 processor core is designed for high-end applications: RAID controllers, SAN, ISCSI, routers,
switches, printers, set-top boxes, etc. It is the first processor core to implement the Book E PowerPC embedded
architecture and the first to use the 128-bit version of IBM’s on-chip CoreConnect Bus Architecture.
Features include:
• Up to 800MHz operation
• PowerPC Book E architecture
• 32KB I-cache, 32KB D-cache
- UTLB Word Wide parity on data and tag address parity with exception force
• Three logical regions in D-cache: locked, transient, normal
• D-cache full line flush capability
• 41-bit virtual address, 36-bit (64GB) physical address
• Superscalar, out-of-order execution
• 7-stage pipeline
• 3 execution pipelines
• Dynamic branch prediction
• Memory management unit
- 64-entry, full associative, unified TLB with parity
- Separate instruction and data micro-TLBs
- Storage attributes for write-through, cache-inhibited, guarded, and big or little endian
• Debug facilities
- Multiple instruction and data range breakpoints
- Data value compare
- Single step, branch, and trap events
- Non-invasive real-time trace interface
• 24 DSP instructions
- Single-cycle multiply and multiply-accumulate
- 32 x 32 integer multiply
- 16 x 16 -> 32-bit MAC
Internal Buses
The PowerPC 440GX features three IBM standard on-chip buses: the Processor Local Bus (PLB), the On-Chip
Peripheral Bus (OPB), and the Device Control Register Bus (DCR). The high performance, high bandwidth cores
such as the PowerPC 440 processor core, the DDR SDRAM memory controller, and the PCI-X bridge connect to
the PLB. The OPB hosts lower data rate peripherals. The daisy-chained DCR provides a lower bandwidth path for
passing status and control information between the processor core and the other on-chip cores.
Features include:
•PLB
- 128-bit implementation of the PLB architecture
- Separate and simultaneous read and write data paths
- 64-bit address
- Simultaneous control, address, and data phases
- Four levels of pipelining
- Byte enable capability supporting unaligned transfers
- 32- and 64-byte burst transfers
- 166MHz, maximum 5.2GB/s (simultaneous read and write)(200MHz for 800MHz Rev F parts)
- Processor:bus clock ratios of N:1 and N:2
440GX – Power PC 440GX Embedded Processor
AMCC 11
Revision 1.19 – December 19, 2008
Data Sheet
•OPB
- Dynamic bus sizing 32-, 16-, and 8-bit data path
- 36-bit address
- 83.33MHz, maximum 333MB/s
• DCR
- 32-bit data path
- 10 bit address
On-Chip SRAM
Features include:
• Four banks of 64KB each for a total of 256KB
• Configurable as either Code (L2) cache or software-controlled on-chip memory, or SRAM
• Memory cycles supported:
- Single beat read and write, 1 to 16 bytes
- 32- and 64-byte burst transfers
- Guarded memory accesses
• Sustainable 2.6GB/s peak bandwidth at 166MHz
• Use as an L2 cache improves processor performance and reduces the PLB load
- Cache coherency maintained by a hardware snoop mechanism or software
- Data Array and Tag Array parity
- Unified data and instruction cache
- 4-way set associative
- 36-bit addressing
- Full LRU replacement algorithm
- Write through, look aside
• Use as Ethernet packet store allows Ethernet packets to be held for processing by the TAH unit
PCI-X Interface
The PCI-X interface allows connection of PCI and PCI-X devices to the PowerPC processor and local memory.
This interface is designed to Version 1.0a of the PCI-X Specification and supports 32- and 64-bit PCI-X buses. PCI
32/64-bit conventional mode, compatible with PCI Version 2.3, is also supported.
Reference Specifications:
• PowerPC CoreConnect Bus (PLB) Specification Version 3.1
• PCI Specification Version 2.3
• PCI Bus Power Management Interface Specification Version 1.1
Features include:
• PCI-X 1.0a
- Split transactions
- Frequency to 133MHz
- 32- and 64-bit bus
• PCI 2.3 backward compatibility
- Frequency to 66MHz
- 32- and 64-bit bus
• Can be the PCI Host Bus Bridge or an Adapter Device's PCI interface
• Internal PCI arbitration function, supporting up to six external devices, that can be disabled for use with an
external arbiter
• Support for Message Signaled Interrupts
440GX – Power PC 440GX Embedded Processor
12 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
• Simple message passing capability
• Asynchronous to the PLB
• PCI Power Management 1.1
• PCI register set addressable both from on-chip processor and PCI device sides
• Ability to boot from PCI-X bus memory
• Error tracking/status
• Supports initiation of transfer to the following address spaces:
- Single beat I/O reads and writes
- Single beat and burst memory reads and writes
- Single beat configuration reads and writes (type 0 and type 1)
- Single beat special cycles
DDR SDRAM Memory Controller
The Double Data Rate (DDR) SDRAM memory controller supports industry standard 184-pin DIMMs, SO-DIMMs,
and other discrete devices. Up to four 512MB logical banks are supported in limited configurations. Global memory
timings, address and bank sizes, and memory addressing modes are programmable.
Features include:
• Registered and non-registered industry standard DIMMs
• 64-bit memory interface with optional 8-bit ECC (SEC/DED)
• Sustainable 2.6GB/s peak bandwidth at 166MHz (200MHz for 800MHz Rev F parts)
• SSTL_2 logic
• 1 to 4 chip selects
• CAS latencies of 2, 2.5 and 3 supported
• DDR200/266/333 support
• Page mode accesses (up to eight open pages) with configurable paging policy
• Programmable address mapping and timing
• Hardware and software initiated self-refresh
• Power management (self-refresh, suspend, sleep)
External Peripheral Bus Controller (EBC)
Features include:
• Up to eight ROM, EPROM, SRAM, Flash memory, and slave peripheral I/O banks supported
• Up to 83.33MHz operation (333MB/s)
• Burst and non-burst devices
• 8-, 16-, 32-bit byte-addressable data bus
• 32-bit address, 4GB address space
• Peripheral Device pacing with external “Ready”
• Latch data on Ready, synchronous or asynchronous
• Programmable access timing per device
- 256 Wait States for non-burst
- 32 Burst Wait States for first access and up to 8 Wait States for subsequent accesses
- Programmable CSon, CSoff relative to address
- Programmable OEon, WEon, WEoff (1 to 4 clock cycles) relative to CS
• Programmable address mapping
• External DMA Slave Support
440GX – Power PC 440GX Embedded Processor
AMCC 13
Revision 1.19 – December 19, 2008
Data Sheet
• External master interface
- Write posting from external master
- Read prefetching on PLB for external master reads
- Bursting capable from external master
- Allows external master access to all non-EBC PLB slaves
- External master can control EBC slaves for own access and control
Ethernet Controller Interface
Ethernet support provided by the PPC440GX interfaces to the physical layer, but the PHY is not included on the
chip.
Features include:
• One to four 10/100 interfaces running in full- and half-duplex modes
- One full Media Independent Interface (MII) with 4-bit parallel data transfer
- Two Reduced Media Independent Interfaces (RMII) with 2-bit parallel data transfer
- Four Serial Media Independent Interfaces (SMII)
• One or two GMII interfaces running in full- and half-duplex modes at 10Mb/s or 100Mb/s or 1000Mb/s
- One full Gigabit Media Independent Interface (GMII) with 8-bit parallel data transfer
- Two Reduced Gigabit Media Independent Interfaces (RGMII) with 4-bit parallel data transfer
• One or two TBI interfaces running in full- and half-duplex modes at 10Mb/s or 100Mb/s or 1000Mb/s
- One full Ten Bit Interface (TBI) with 10-bit parallel data transfer
- Two Reduced Ten Bit Interfaces (RTBI) with 4-bit parallel data transfer
• Jumbo frame support (9016 byte)
- Support for Ethernet II formatted frames (RFC894)
- Support for IEEE formatted frames (RFC1042)
- Handles VLAN-tagged frames
TCP/IP Acceleration Hardware (TAH)
Features include:
• Offloads Gigabit Ethernet protocol processing from the CPU
• Checksum verification for TCP/UDP/IP headers in the receive path
• Checksum generation for TCP/UDP/IP headers in the transmit path
• TCP segmentation support in the transmit path
DMA Controller
Features include:
• Supports the following transfers:
- Memory-to-memory transfers
- Buffered peripheral to memory transfers
- Buffered memory to peripheral transfers
• Four channels
• Scatter/Gather capability for programming multiple DMA operations
• 8-, 16-, 32-bit peripheral support (OPB and external)
• 64-bit addressing
• 128 byte FIFO buffer
• Address increment or decrement
• Supports internal and external peripherals
• Support for memory mapped peripherals
440GX – Power PC 440GX Embedded Processor
14 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
• Support for peripherals running on slower frequency buses
Serial Port
Features include:
• One 8-pin UART and one 4-pin UART interface provided
• Selectable internal or external serial clock to allow wide range of baud rates
• Register compatibility with 16750 register set
• Complete status reporting capability
• Fully programmable serial-interface characteristics
• Supports DMA using internal DMA engine
IIC Bus Interface
Features include:
• Two IIC interfaces provided
• Support for Philips® Semiconductors I2C Specification, dated 1995
• Operation at 100kHz or 400kHz
•8-bit data
• 10- or 7-bit address
• Slave transmitter and receiver
• Master transmitter and receiver
• Multiple bus masters
• Supports fixed VDD IIC interface
• Two independent 4 x 1 byte data buffers
• Twelve memory-mapped, fully programmable configuration registers
• One programmable interrupt request signal
• Provides full management of all IIC bus protocols
• Programmable error recovery
General Purpose Timers (GPT)
Provides a separate time base counter and additional system timers in addition to those defined in the processor
core.
• 32-bit Time Base Counter driven by the OPB bus clock
• Seven 32-bit compare timers
General Purpose IO (GPIO) Controller
• Controller functions and GPIO registers are programmed and accessed via memory-mapped OPB bus master
accesses.
• The 32 GPIOs are pin-shared with other functions. DCRs control whether a particular pin that has GPIO
capabilities acts as a GPIO or is used for another purpose.
• Each GPIO output is separately programmable to emulate an open drain driver (that is, drives to zero,
tri-stated if output bit is 1).
440GX – Power PC 440GX Embedded Processor
AMCC 15
Revision 1.19 – December 19, 2008
Data Sheet
Universal Interrupt Controller (UIC)
Four Universal Interrupt Controllers (UIC) are available. They provide control, status, and communications
necessary between the external and internal sources of interrupts and the on-chip PowerPC processor.
Note: Processor specific interrupts (for example, page faults) do not use UIC resources.
Features include:
• 18 external interrupts
• 63 internal interrupts
• Edge triggered or level-sensitive
• Positive or negative active
• Non-critical or critical interrupt to the on-chip processor core
• Programmable interrupt priority ordering
• Programmable critical interrupt vector for faster vector processing
PLB Performance Monitor
The PLB Performance Monitor (PPM) provides hardware for counting certain events associated with PLB
transactions. The contents of the counters can be read by software for analysis and enhancement of PLB
performance, or software debug. The data includes identification and duration of the events.
I2O Messaging Unit (IMU)
The IMU interfaces to the PLB as a master or slave and allows messages to be transferred between two PLB
masters (for example, the 440 CPU and PCI-X).
Features include:
• Three messaging methods
- 4 Message registers—2 inbound, 2 outbound
- 2 Doorbell registers—1 inbound, 1 outbound
- 4 Circular queues—2 inbound, 2 outbound
• Up to 7 different interrupt outputs generated
• Support for interrupt masking
JTAG
Features include:
• IEEE 1149.1 Test Access Port
• IBM RISCWatch Debugger support
• JTAG Boundary Scan Description Language (BSDL)
440GX – Power PC 440GX Embedded Processor
16 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
25mm, 552-Ball Ceramic (CBGA) Package
Top View
Bottom View
Notes: 1. All dimensions are in mm.
A1 Corner
135 7911131517
19
246810
12 14 16 18
21 23
20 22 24
A
BC
DE
FG
HJ
KL
M
AA
N
PR
TU
VW
Y
AB AC
AD
25.0 ± 0.2
1.00 Typ
25.0 ± 0.2
0.8 ± 0.04 Solderball x 552
23.0
Capacitor
8.4
Chip
2.31 max
1.89 min
3.977 max
0.71 min
0.81 max 0.779 min
0.857 max
3.379 min
2. RoHS compliant reduced-lead package available.
3. Reduced-lead package dimensions are in parentheses (dimension).
(0.7 ± 0.1)
(0.60 max)
(3.707 max)
(3.179 min)
(0.907 max)
(2.20 max)
(2.00 min)
(0.779 min)
(0.40 max)
124
A
AD
AAAAAAAA
PPC440GX–3xxfffx
Lot Number
Part Number
440GX – Power PC 440GX Embedded Processor
AMCC 17
Revision 1.19 – December 19, 2008
Data Sheet
25mm, 552-Ball Plastic (FC-PBGA) Package
Top View
Bottom View
Notes: 1. All dimensions are in mm.
A1 Corner
135 7911131517
19
246810
12 14 16 18
21 23
20 22 24
A
BC
DE
FG
HJ
KL
M
AA
N
PR
TU
VW
Y
AB AC
AD
25.0
1.00 Typ
25.0
0.66 ± 0.1 Solderball x 552
23.0
7.5
0.5 ± 0.1
3.191 ± 0.17
1.214 Ref
1 ± 0.3
0.508 Ref
24
AD
A
1
23.0
2. Available in lead-free, RoHS compliant version.
PPC440GX
3xxfffx
Part Number
AAAAAAAA
Lot Number
®
440GX – Power PC 440GX Embedded Processor
18 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Signal Lists
The following table lists all the external signals in alphabetical order and shows the ball (pin) number on which the
signal appears. Multiplexed signals are shown with the default signal (following reset) not in brackets and the
alternate signal in brackets. Multiplexed signals appear alphabetically multiple times in the list—once for each
signal name on the ball. The page number listed gives the page in “Signal Functional Description” on page 50
where the signals in the indicated interface group begin. In cases where signals in the same interface group (for
example, Ethernet) have different names to distinguish variations in the mode of operation, the names are
separated by a comma with the primary name appearing first. These signals are listed only once, and appear
alphabetically by the primary name.
Signals Listed Alphabetically (Sheet 1 of 24)
Signal Name Ball Interface Group Page
APGND J01
Power—Analog ground 57ASGND J24
AMGND AA11
AMVDD AB11 Power—MemClkOut PLL analog voltage 57
APVDD G01 Power—PCI-X PLL analog voltage 57
ASVDD G24 Power—SysClk PLL analog voltage 57
BA0 AA16
DDR SDRAM 51
BA1 AD09
BankSel0 AB15
DDR SDRAM 51
BankSel1 W14
BankSel2 AD11
BankSel3 AD05
[BE0]PCIXC0 F14
PCI-X 50
[BE1]PCIXC1 E16
[BE2]PCIXC2 C19
[BE3]PCIXC3 F20
[BE4]PCIXC4 C08
[BE5]PCIXC5 C03
[BE6]PCIXC6 G09
[BE7]PCIXC7 F09
BusReq[TrcTS1] AA24 External Master Peripheral 54
CAS AB05 DDR SDRAM 51
ClkEn0 AD17
DDR SDRAM 51
ClkEn1 AB10
ClkEn2 Y09
ClkEn3 W09
440GX – Power PC 440GX Embedded Processor
AMCC 19
Revision 1.19 – December 19, 2008
Data Sheet
DM0 T16
DDR SDRAM 51
DM1 AA18
DM2 AB14
DM3 P13
DM4 AA09
DM5 AA07
DM6 Y03
DM7 V03
DM8 AC05
DMAAck0 N05
External Slave Peripheral 53
DMAAck1 P07
DMAAck2[GMCRxD0, GMC0RxD0,
TBIRxD0, RTBI0RxD0] P06
DMAAck3[GMCRxD1, GMC0RxD1,
TBIRxD1, RTBI0RxD1] P11
DMAReq0 R03
External Slave Peripheral 53
DMAReq1 M11
DMAReq2[GMCRxDV, GMC0RxCtl,
TBIRxD8, RTBI0RxD4] N11
DMAReq3[GMCTxEn, GMC0TxCtl,
TBITxD8, RTBI0TxD4] P01
DQS0 AC20
DDR SDRAM 51
DQS1 AC16
DQS2 AC14
DQS3 AB13
DQS4 AC11
DQS5 AC09
DQS6 Y04
DQS7 T01
DQS8 AA05
DrvrInh2 A05 System 56
Signals Listed Alphabetically (Sheet 2 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
20 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
ECC0 AB07
DDR SDRAM 51
ECC1 AB06
ECC2 AD06
ECC3 W07
ECC4 U09
ECC5 AC03
ECC6 AB04
ECC7 AD04
EMCCD, EMC1RxErr, GMCGTxClk,
GMC0TxClk, TBITxClk, RTBI0TxClk J07 Ethernet 51
EMCCrS, EMC0CrSDV, GMCTxD7,
GMC1TxD3, TBITxD7, RTBI1TxD3 K07 Ethernet 51
EMCMDClk J08 Ethernet 51
EMCMDIO L05 Ethernet 51
EMCRxClk, GMCTxD5, GMC1TxD1,
TBITxD5, RTBI1TxD1 J02 Ethernet 51
EMCRxD0, EMC0RxD0, EMC0RxD G03
Ethernet 51
EMCRxD1, EMC0RxD1, EMC1RxD E01
EMCRxD2, EMC1RxD0, EMC2RxD,
GMCTxD0, GMC0TxD0, TBITxD0,
RTBI0TxD0
A07
EMCRxD3, EMC1RxD1, EMC3RxD
GMCTxD1, GMC0TxD1, TBITxD1,
RTBI0TxD1
H09
EMCRxDV, EMC1CrSDV, GMCTxD4,
GMC1TxD0, TBITxD4, RTBI1TxD0 K01 Ethernet 51
EMCRxErr, EMC0RxErr, GMCTxD6,
GMC1TxD2, TBITxD6, RTBI1TxD2 K03 Ethernet 51
EMCTxClk, EMCRefClk J06 Ethernet 51
EMCTxD0, EMC0TxD0, EMC0TxD L09
Ethernet 51
EMCTxD1, EMC0TxD1, EMC1TxD K05
EMCTxD2, EMC1TxD0, EMC2TxD,
GMCTxD2, GMC0TxD2, TBITxD2,
RTBI0TxD2
J04
EMCTxD3, EMC1TxD1, EMC3TxD,
GMCTxD3, GMC0TxD3, TBITxD3,
RTBI0TxD3
J03
EMCTxEn, EMC0TxEn, EMCSync L06 Ethernet 51
EMCTxErr, EMC1TxEn, GMCRxClk,
GMC0RxClk, TBIRxClk0, RTBI0RxClk C05 Ethernet 51
Signals Listed Alphabetically (Sheet 3 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
AMCC 21
Revision 1.19 – December 19, 2008
Data Sheet
EOT0/TC0 R16
External Slave Peripheral 53
EOT1/TC1 P15
EOT2/TC2[GMCRxD2, GMC0RxD2,
TBIRxD2, RTBI0RxD2] P16
EOT3/TC3[GMCRxD3, GMC0RxD3,
TBIRxD3, RTBI0RxD3] M16
ExtAck[TrcTS2] AA22 External Master Peripheral 54
ExtReq[TrcTS3] AB23 External Master Peripheral 54
ExtReset T17 External Master Peripheral 54
[GMCCD, GMC1RxClk,
RTBI1RxClk]TrcTS1[GPIO27] P03 Ethernet 51
[GMCCrS, GMC1TxClk,
RTBI1TxClk]TrcTS6 R01 Ethernet 51
GMCRefClk L01 Ethernet 51
[GMCRxD0, GMC0RxD0, TBIRxD0,
RTBI0RxD0]DMAAck2 P06
Ethernet 51
[GMCRxD1, GMC0RxD1, TBIRxD1,
RTBI0RxD1]DMAAck3 P11
[GMCRxD2, GMC0RxD2, TBIRxD2,
RTBI0RxD2]EOT2/TC2 P16
[GMCRxD3, GMC0RxD3, TBIRxD3,
RTBI0RxD3]EOT3/TC3 M16
[GMCRxD4, GMC1RxD0, TBIRxD4,
RTBI1RxD0][GPIO28]TrcTS2 R07
[GMCRxD5, GMC1RxD1, TBIRxD5,
RTBI1RxD1][GPIO29]TrcTS3 P09
[GMCRxD6, GMC1RxD2, TBIRxD6,
RTBI1RxD2][GPIO30]TrcTS4 R09
[GMCRxD7, GMC1RxD3, TBIRxD7,
RTBI1RxD3][GPIO31]TrcTS5 T06
[GMCRxDV, GMC0RxCtl, TBIRxD8,
RTBI0RxD4]DMAReq2 N11 Ethernet 51
GMCRxEr, GMC1RxCtl, TBIRxD9,
RTBI1RxD4 P04 Ethernet 51
GMCTxEr, GMC1TxCtl, TBITxD9,
RTBI1TxD4 L07 Ethernet
Note: Used as initialization strapping input. 51
[GMCTxEn, GMC0TxCtl, TBITxD8,
RTBI0TxD4]DMAReq3 P01 Ethernet 51
[GMCTxClk, TBIRxClk1]GPIO11 P14 Ethernet 51
Signals Listed Alphabetically (Sheet 4 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
22 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
GND B06
Power 57
GND B10
GND B13
GND B17
GND B21
GND D04
GND D08
GND D12
GND D15
GND D19
GND D23
GND F02
GND F06
GND F10
GND F13
GND F17
GND F21
GND H04
GND H08
GND H12
GND H15
GND H19
GND H23
GND K02
GND K06
GND K10
GND K13
GND K17
GND K21
GND M04
Signals Listed Alphabetically (Sheet 5 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
AMCC 23
Revision 1.19 – December 19, 2008
Data Sheet
GND M08
Power 57
GND M12
GND M15
GND M19
GND M23
GND N02
GND N06
GND N10
GND N13
GND N17
GND N21
GND R04
GND R08
GND R12
GND R15
GND R19
GND R23
GND U02
GND U06
GND U10
GND U13
GND U17
GND U21
GND W04
GND W08
GND W12
GND W15
GND W19
GND W23
Signals Listed Alphabetically (Sheet 6 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
24 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
GND AA02
Power 57
GND AA06
GND AA10
GND AA13
GND AA17
GND AA21
GND AC04
GND AC08
GND AC12
GND AC15
GND AC19
Signals Listed Alphabetically (Sheet 7 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
AMCC 25
Revision 1.19 – December 19, 2008
Data Sheet
[GPIO00]IRQ00 N18
System 56
[GPIO01]IRQ01 L20
[GPIO02]IRQ02 P20
[GPIO03]IRQ03 L18
[GPIO04]IRQ04 N14
[GPIO05]IRQ05 M20
[GPIO06]IRQ06 M14
[GPIO07]IRQ07 P18
[GPIO08]IRQ08 N20
[GPIO09]IRQ09 P22
[GPIO10]IRQ10 V18
GPIO11[GMCTxClk, TBIRxClk1] P14
[GPIO12]UART1_Rx C18
[GPIO13]UART1_Tx J16
[GPIO14]UART1_DSR/CTS G06
[GPIO15]UART1_RTS/DTR E05
[GPIO16]IIC1SClk H11
[GPIO17]IIC1SDA H14
[GPIO18]TrcBS0[IRQ13] N16
[GPIO19]TrcBS1[IRQ14] P17
[GPIO20]TrcBS2[IRQ15] T20
[GPIO21]TrcES0[IRQ16] T21
[GPIO22]TrcES1[IRQ17] P23
[GPIO23]TrcES2 N09
[GPIO24]TrcES3 P08
[GPIO25]TrcES4 T05
[GPIO26]TrcTS0 T04
[GPIO27]TrcTS1[GMCCD, GMC1RxClk,
RTBI1RxClk] P03
[GPIO28]TrcTS2[GMCRxD4, GMC1RxD0,
TBIRxD4, RTBI1RxD0] R07
[GPIO29]TrcTS3[GMCRxD5, GMC1RxD1,
TBIRxD5, RTBI1RxD1] P09
[GPIO30]TrcTS4[GMCRxD6, GMC1RxD2,
TBIRxD6, RTBI1RxD2] R09
[GPIO31]TrcTS5[GMCRxD7, GMC1RxD3,
TBIRxD7, RTBI1RxD3] T06
Signals Listed Alphabetically (Sheet 8 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
26 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Halt V05 System 56
HoldAck[TrcTS4] Y21 External Master Peripheral 54
HoldReq[TrcTS5] Y23 External Master Peripheral 54
IIC0SClk G11 IIC Peripheral 55
IIC0SDA G13 IIC Peripheral 55
IIC1SClk[GPIO16] H11 IIC Peripheral 55
IIC1SDA[GPIO17] H14 IIC Peripheral 55
IRQ00[GPIO00] N18
Interrupts 55
IRQ01[GPIO01] L20
IRQ02[GPIO02] P20
IRQ03[GPIO03] L18
IRQ04[GPIO04] N14
IRQ05[GPIO05] M20
IRQ06[GPIO06] M14
IRQ07[GPIO07] P18
IRQ08[GPIO08] N20
IRQ09[GPIO09] P22
IRQ10[GPIO10] V18
[IRQ11]PCIReq1 E21
[IRQ12]PCIGnt1 C22
[IRQ13][GPIO18]TrcBS0 N16
[IRQ14][GPIO19]TrcBS1 P17
[IRQ15][GPIO20]TrcBS2 T20
[IRQ16][GPIO21]TrcES0 T21
[IRQ17][GPIO22]TrcES1 P23
Signals Listed Alphabetically (Sheet 9 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
AMCC 27
Revision 1.19 – December 19, 2008
Data Sheet
MemAddr00 Y19
DDR SDRAM 51
MemAddr01 AD20
MemAddr02 Y20
MemAddr03 AB20
MemAddr04 AD18
MemAddr05 AD16
MemAddr06 AB18
MemAddr07 Y14
MemAddr08 V13
MemAddr09 V11
MemAddr10 W16
MemAddr11 Y11
MemAddr12 V10
MemClkOut0 V09
DDR SDRAM 51
MemClkOut0 V08
Signals Listed Alphabetically (Sheet 10 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
28 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
MemData00 AD21
DDR SDRAM 51
MemData01 AB21
MemData02 AC22
MemData03 AA20
MemData04 U16
MemData05 V17
MemData06 AD19
MemData07 AB19
MemData08 W18
MemData09 V16
MemData10 Y17
MemData11 AB16
MemData12 AC18
MemData13 Y18
MemData14 R14
MemData15 AB17
MemData16 AA14
MemData17 AD15
MemData18 T15
MemData19 V15
MemData20 Y16
MemData21 U14
MemData22 T13
MemData23 Y15
MemData24 AD13
MemData25 AD14
MemData26 V14
MemData27 Y13
MemData28 P12
MemData29 AB12
MemData30 Y12
MemData31 V12
Signals Listed Alphabetically (Sheet 11 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
AMCC 29
Revision 1.19 – December 19, 2008
Data Sheet
MemData32 W11
DDR SDRAM 51
MemData33 AD12
MemData34 Y10
MemData35 T12
MemData36 U11
MemData37 T11
MemData38 T10
MemData39 AD10
MemData40 AB08
MemData41 AD08
MemData42 R11
MemData43 Y07
MemData44 AC07
MemData45 AB09
MemData46 Y06
MemData47 Y08
MemData48 AA01
MemData49 AA03
MemData50 AB02
MemData51 Y01
MemData52 AB03
MemData53 Y02
MemData54 V07
MemData55 V01
MemData56 T08
MemData57 U07
MemData58 W01
MemData59 W03
MemData60 V06
MemData61 T07
MemData62 W05
MemData63 U05
MemVRef1 T14
DDR SDRAM 51
MemVRef2 T09
Signals Listed Alphabetically (Sheet 12 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
30 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
No ball A01
A physical ball does not exist at these ball coordinates. NA
No ball A02
No ball A03
No ball A22
No ball A23
No ball A24
No ball B01
No ball B02
No ball B23
No ball B24
No ball C01
No ball C24
No ball AB01
No ball AB24
No ball AC01
No ball AC02
No ball AC23
No ball AC24
No ball AD01
No ball AD02
No ball AD03
No ball AD22
No ball AD23
No ball AD24
Signals Listed Alphabetically (Sheet 13 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
AMCC 31
Revision 1.19 – December 19, 2008
Data Sheet
OVDD B04
Power 57
OVDD B12
OVDD B19
OVDD D02
OVDD D10
OVDD D17
OVDD F08
OVDD F15
OVDD F23
OVDD H06
OVDD H10
OVDD H13
OVDD H21
OVDD K04
OVDD K08
OVDD K19
OVDD M02
OVDD M17
OVDD N08
OVDD N23
OVDD R06
OVDD R17
OVDD R21
OVDD U04
OVDD U19
OVDD W02
OVDD AA23
PCIX133Cap G08 PCI-X 50
PCIXAck64 D09 PCI-X 50
Signals Listed Alphabetically (Sheet 14 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
32 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
PCIXAD00 C17
PCI-X 50
PCIXAD01 B09
PCIXAD02 G10
PCIXAD03 E10
PCIXAD04 C10
PCIXAD05 A10
PCIXAD06 F11
PCIXAD07 G12
PCIXAD08 G14
PCIXAD09 A15
PCIXAD10 C15
PCIXAD11 E15
PCIXAD12 G15
PCIXAD13 B16
PCIXAD14 C16
PCIXAD15 D16
PCIXAD16 E18
PCIXAD17 E19
PCIXAD18 F18
PCIXAD19 G18
PCIXAD20 D20
PCIXAD21 A20
PCIXAD22 A21
PCIXAD23 C21
PCIXAD24 F22
PCIXAD25 B22
PCIXAD26 G21
PCIXAD27 E23
PCIXAD28 C23
PCIXAD29 F24
PCIXAD30 D22
PCIXAD31 D24
Signals Listed Alphabetically (Sheet 15 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
AMCC 33
Revision 1.19 – December 19, 2008
Data Sheet
PCIXAD32 H03
PCI-X 50
PCIXAD33 H01
PCIXAD34 L08
PCIXAD35 F01
PCIXAD36 D01
PCIXAD37 J05
PCIXAD38 H05
PCIXAD39 G02
PCIXAD40 E02
PCIXAD41 C02
PCIXAD42 A08
PCIXAD43 G05
PCIXAD44 F03
PCIXAD45 D03
PCIXAD46 B03
PCIXAD47 H07
PCIXAD48 G04
PCIXAD49 E04
PCIXAD50 C04
PCIXAD51 A04
PCIXAD52 F05
PCIXAD53 D05
PCIXAD54 B05
PCIXAD55 C09
PCIXAD56 E06
PCIXAD57 C06
PCIXAD58 A06
PCIXAD59 F07
PCIXAD60 E07
PCIXAD61 D07
PCIXAD62 B07
PCIXAD63 E08
Signals Listed Alphabetically (Sheet 16 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
34 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
PCIXC0[BE0]F14
PCI-X 50
PCIXC1[BE1]E16
PCIXC2[BE2]C19
PCIXC3[BE3]F20
PCIXC4[BE4]C08
PCIXC5[BE5]C03
PCIXC6[BE6]G09
PCIXC7[BE7]F09
PCIXCap L23 PCI-X 50
PCIXClk E03 PCI-X 50
PCIXDevSel E13 PCI-X 50
PCIXFrame A11 PCI-X 50
PCIXGnt0 E22
PCI-X 50
PCIXGnt1[IRQ12] C22
PCIXGnt2 N22
PCIXGnt3 M18
PCIXGnt4 R22
PCIXGnt5 P19
PCIXIDSel G07 PCI-X 50
PCIXINT M07 PCI-X 50
PCIXIRDY E12 PCI-X 50
PCIXM66En A14 PCI-X 50
PCIXParHigh L04 PCI-X 50
PCIXParLow F16 PCI-X 50
PCIXPErr A17 PCI-X 50
PCIXReq0 E24
PCI-X 50
PCIXReq1[IRQ11] E21
PCIXReq2 E20
PCIXReq3 R20
PCIXReq4 G23
PCIXReq5 R18
PCIXReq64 E09 PCI-X 50
PCIXReset M24 PCI-X 50
PCIXSErr A18 PCI-X 50
Signals Listed Alphabetically (Sheet 17 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
AMCC 35
Revision 1.19 – December 19, 2008
Data Sheet
PCIXStop L12 PCI-X 50
PCIXTRDY C12 PCI-X 50
PerAddr00 D11
External Slave Peripheral
Note: PerAddr00 is the most significant bit (msb) on this bus. 53
PerAddr01 C11
PerAddr02 B11
PerAddr03 A12
PerAddr04 A19
PerAddr05 D18
PerAddr06 E11
PerAddr07 M03
PerAddr08 N01
PerAddr09 E14
PerAddr10 C20
PerAddr11 A16
PerAddr12 A13
PerAddr13 B14
PerAddr14 C14
PerAddr15 D14
PerAddr16 B20
PerAddr17 L15
PerAddr18 L21
PerAddr19 L22
PerAddr20 M22
PerAddr21 M01
PerAddr22 L24
PerAddr23 P24
PerAddr24 T19
PerAddr25 R24
PerAddr26 U22
PerAddr27 U24
PerAddr28 N03
PerAddr29 V20
PerAddr30 V23
PerAddr31 V21
Signals Listed Alphabetically (Sheet 18 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
36 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
PerBLast C07 External Slave Peripheral 53
PerClk U18 External Master Peripheral 54
PerCS0 E17
External Slave Peripheral 53
PerCS1 L10
PerCS2 V04
PerCS3 T24
PerCS4 L03
PerCS5 T03
PerCS6 L13
PerCS7 U03
Signals Listed Alphabetically (Sheet 19 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
AMCC 37
Revision 1.19 – December 19, 2008
Data Sheet
PerData00 H24
External Slave Peripheral
Note: PerData00 is the most significant bit (msb) on this bus. 53
PerData01 H22
PerData02 H20
PerData03 G20
PerData04 G19
PerData05 H18
PerData06 J23
PerData07 J22
PerData08 J21
PerData09 J20
PerData10 J19
PerData11 J18
PerData12 J17
PerData13 J15
PerData14 J14
PerData15 J13
PerData16 J12
PerData17 J11
PerData18 J10
PerData19 J09
PerData20 L14
PerData21 K24
PerData22 K22
PerData23 K20
PerData24 K18
PerData25 K16
PerData26 K14
PerData27 K11
PerData28 K09
PerData29 L19
PerData30 L17
PerData31 L16
[PerErr]TrcTS6 P21 External Master Peripheral 54
PerOE M09 External Slave Peripheral 53
Signals Listed Alphabetically (Sheet 20 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
38 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
PerPar0 T23
External Slave Peripheral 53
PerPar1 T22
PerPar2 W20
PerPar3 U20
PerReady[RcvrInh] N07 External Slave Peripheral 53
PerR/W P05 External Slave Peripheral 53
PerWBE0 T18
External Slave Peripheral 53
PerWBE1 V19
PerWBE2 W22
PerWBE3 W24
PerWE P02 External Slave Peripheral 53
RAS AD07 DDR SDRAM 51
[RcvrInh]PerReady N07 System 56
RefVEn L02 System 56
SVDD U12
Power 57
SVDD U15
SVDD W10
SVDD W17
SVDD AA08
SVDD AA15
SVDD AC06
SVDD AC13
SVDD AC21
SysClk G22 System 56
SysErr T02 System 56
SysReset P10 System 56
TCK V22 JTAG 55
TDI Y24 JTAG 55
TDO Y22 JTAG 55
TestEn M05 System 56
TmrClk U01 System 56
TMS AB22 JTAG 55
Signals Listed Alphabetically (Sheet 21 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
AMCC 39
Revision 1.19 – December 19, 2008
Data Sheet
TrcBS0[GPIO18][IRQ13] N16
Trace 57TrcBS1[GPIO19][IRQ14] P17
TrcBS2[GPIO20][IRQ15] T20
TrcClk R05 Trace 57
TrcES0[GPIO21][IRQ16] T21
Trace 57
TrcES1[GPIO22][IRQ17] P23
TrcES2[GPIO23] N09
TrcES3[GPIO24] P08
TrcES4[GPIO25] T05
TrcTS0[GPIO26] T04 Trace 57
TrcTS1[GPIO27][GMCCD, GMC1RxClk,
RTBI1RxClk] P03 Trace 57
[TrcTS1]BusReq AA24 Trace 57
TrcTS2[GPIO28][GMCRxD4, GMC1RxD0,
TBIRxD4, RTBI1RxD0] R07 Trace 57
[TrcTS2]ExtAck AA22 Trace 57
TrcTS3[GPIO29][GMCRxD5, GMC1RxD1,
TBIRxD5, RTBI1RxD1] P09 Trace 57
[TrcTS3]ExtReq AB23 Trace 57
TrcTS4[GPIO30][GMCRxD6, GMC1RxD2,
TBIRxD6, RTBI1RxD2] R09 Trace 57
[TrcTS4]HoldAck Y21 Trace 57
TrcTS5[GPIO31][GMCRxD7, GMC1RxD3,
TBIRxD7, RTBI1RxD3] T06 Trace 57
[TrcTS5]HoldReq Y23 Trace 57
TrcTS6[GMCCrS, GMC1TxClk,
RTBI1TxClk] R01 Trace 57
TrcTS6[PerErr] P21 Trace 57
TRST N24 JTAG 55
UART0_CTS C13 UART Peripheral 54
UART0_DCD V24 UART Peripheral
Note: Used as initialization strapping input. 54
UART0_DSR V02 UART Peripheral
Note: Used as initialization strapping input. 54
UART0_DTR B18 UART Peripheral 54
UART0_RI H16 UART Peripheral 54
UART0_RTS G16 UART Peripheral 54
UART0_Rx G17 UART Peripheral 54
Signals Listed Alphabetically (Sheet 22 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
40 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
UART0_Tx L11 UART Peripheral 54
UART1_DSR/CTS[GPIO14] G06 UART Peripheral 54
UART1_RTS/DTR[GPIO15] E05 UART Peripheral 54
UART1_Rx[GPIO12] C18 UART Peripheral 54
UART1_Tx[GPIO13] J16 UART Peripheral 54
UARTSerClk A09 UART Peripheral 54
VDD B08
Power 57
VDD B15
VDD D06
VDD D13
VDD D21
VDD F04
VDD F12
VDD F19
VDD H02
VDD H17
VDD K12
VDD K15
VDD K23
VDD M06
VDD M10
VDD M13
VDD M21
VDD N04
VDD N12
VDD N15
Signals Listed Alphabetically (Sheet 23 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
AMCC 41
Revision 1.19 – December 19, 2008
Data Sheet
VDD N19
Power 57
VDD R02
VDD R10
VDD R13
VDD U08
VDD U23
VDD W06
VDD W13
VDD W21
VDD AA04
VDD AA12
VDD AA19
VDD AC10
VDD AC17
WE Y05 DDR SDRAM 51
Signals Listed Alphabetically (Sheet 24 of 24)
Signal Name Ball Interface Group Page
440GX – Power PC 440GX Embedded Processor
42 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
In the following table, only the primary (default) signal name is shown for each pin. Multiplexed or multifunction
signals are marked with an asterisk (*). To determine what signals or functions are multiplexed on those pins, look
up the primary signal name in “Signals Listed Alphabetically” on page 18.
Signals Listed by Ball Assignment (Sheet 1 of 6)
Ball Signal Name Ball Signal Name Ball Signal Name Ball Signal Name
A01 No ball B01 No ball C01 No ball D01 PCIXAD36
A02 No ball B02 No ball C02 PCIXAD41 D02 OVDD
A03 No ball B03 PCIXAD46 C03 PCIXC5 * D03 PCIXAD45
A04 PCIXAD51 B04 OVDD C04 PCIXAD50 D04 GND
A05 DrvrInh2 B05 PCIXAD54 C05 EMCTxErr * D05 PCIXAD53
A06 PCIXAD58 B06 GND C06 PCIXAD57 D06 VDD
A07 EMCRxD2 * B07 PCIXAD62 C07 PerBLast D07 PCIXAD61
A08 PCIXAD42 B08 VDD C08 PCIXC4 * D08 GND
A09 UARTSerClk B09 PCIXAD01 C09 PCIXAD55 D09 PCIXAck64
A10 PCIXAD05 B10 GND C10 PCIXAD04 D10 OVDD
A11 PCIXFrame B11 PerAddr02 C11 PerAddr01 D11 PerAddr00
A12 PerAddr03 B12 OVDD C12 PCIXTRDY D12 GND
A13 PerAddr12 B13 GND C13 UART0_CTS D13 VDD
A14 PCIXM66En B14 PerAddr13 C14 PerAddr14 D14 PerAddr15
A15 PCIXAD09 B15 VDD C15 PCIXAD10 D15 GND
A16 PerAddr11 B16 PCIXAD13 C16 PCIXAD14 D16 PCIXAD15
A17 PCIXPErr B17 GND C17 PCIXAD00 D17 OVDD
A18 PCIXSErr B18 UART0_DTR C18 UART1_Rx * D18 PerAddr05
A19 PerAddr04 B19 OVDD C19 PCIXC2 * D19 GND
A20 PCIXAD21 B20 PerAddr16 C20 PerAddr10 D20 PCIXAD20
A21 PCIXAD22 B21 GND C21 PCIXAD23 D21 VDD
A22 No ball B22 PCIXAD25 C22 PCIXGnt1 * D22 PCIXAD30
A23 No ball B23 No ball C23 PCIXAD28 D23 GND
A24 No ball B24 No ball C24 No ball D24 PCIXAD31
440GX – Power PC 440GX Embedded Processor
AMCC 43
Revision 1.19 – December 19, 2008
Data Sheet
E01 EMCRxD1 * F01 PCIXAD35 G01 APVDD for PCI PLL H01 PCIXAD33
E02 PCIXAD40 F02 GND G02 PCIXAD39 H02 VDD
E03 PCIXClk F03 PCIXAD44 G03 EMCRxD0 * H03 PCIXAD32
E04 PCIXAD49 F04 VDD G04 PCIXAD48 H04 GND
E05 UART1_RTS/DTR * F05 PCIXAD52 G05 PCIXAD43 H05 PCIXAD38
E06 PCIXAD56 F06 GND G06 UART1_DSR/CTS *H06
OVDD
E07 PCIXAD60 F07 PCIXAD59 G07 PCIXIDSel H07 PCIXAD47
E08 PCIXAD63 F08 OVDD G08 PCIX133Cap H08 GND
E09 PCIXReq64 F09 PCIXC7 * G09 PCIXC6 * H09 EMCRxD3 *
E10 PCIXAD03 F10 GND G10 PCIXAD02 H10 OVDD
E11 PerAddr06 F11 PCIXAD06 G11 IIC0SClk H11 IIC1SClk *
E12 PCIXIRDY F12 VDD G12 PCIXAD07 H12 GND
E13 PCIXDevSel F13 GND G13 IIC0SDA H13 OVDD
E14 PerAdd09 F14 PCIXC0 * G14 PCIXAD08 H14 IIC1SDA *
E15 PCIXAD11 F15 OVDD G15 PCIXAD12 H15 GND
E16 PCIXC1 * F16 PCIXParLow G16 UART0_RTS H16 UART0_RI
E17 PerCS0 F17 GND G17 UART0_Rx H17 VDD
E18 PCIXAD16 F18 PCIXAD18 G18 PCIXAD19 H18 PerData05
E19 PCIXAD17 F19 VDD G19 PerData04 H19 GND
E20 PCIXReq2 F20 PCIXC3 * G20 PerData03 H20 PerData02
E21 PCIXReq1 * F21 GND G21 PCIXAD26 H21 OVDD
E22 PCIXGnt0 F22 PCIXAD24 G22 SysClk H22 PerData01
E23 PCIXAD27 F23 OVDD G23 PCIXReq4 H23 GND
E24 PCIXReq0 F24 PCIXAD29 G24 ASVDD for SysClk PLL H24 PerData00
Signals Listed by Ball Assignment (Sheet 2 of 6)
Ball Signal Name Ball Signal Name Ball Signal Name Ball Signal Name
440GX – Power PC 440GX Embedded Processor
44 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
J01 APGND K01 EMCRxDV * L01 GMCRefClk M01 PerAddr21
J02 EMCRxClk * K02 GND L02 RefVEn M02 OVDD
J03 EMCTxD3 * K03 EMCRxErr * L03 PerCS4 M03 PerAddr07
J04 EMCTxD2 * K04 OVDD L04 PCIXParHigh M04 GND
J05 PCIXAD37 K05 EMCTxD1 * L05 EMCMDIO M05 TestEn
J06 EMCTxClk * K06 GND L06 EMCTxEn * M06 VDD
J07 EMCCD * K07 EMCCrS * L07 GMCTxEr * M07 PCIXINT
J08 EMCMDClk K08 OVDD L08 PCIXAD34 M08 GND
J09 PerData19 K09 PerData28 L09 EMCTxD0 * M09 PerOE
J10 PerData18 K10 GND L10 PerCS1 M10 VDD
J11 PerData17 K11 PerData27 L11 UART0_Tx M11 DMAReq1
J12 PerData16 K12 VDD L12 PCIXStop M12 GND
J13 PerData15 K13 GND L13 PerCS6 M13 VDD
J14 PerData14 K14 PerData26 L14 PerData20 M14 IRQ06 *
J15 PerData13 K15 VDD L15 PerAddr17 M15 GND
J16 UART1_Tx * K16 PerData25 L16 PerData31 M16 EOT3/TC3 *
J17 PerData12 K17 GND L17 PerData30 M17 OVDD
J18 PerData11 K18 PerData24 L18 IRQ03 * M18 PCIXGnt3
J19 PerData10 K19 OVDD L19 PerData29 M19 GND
J20 PerData9 K20 PerData23 L20 IRQ01 * M20 IRQ05 *
J21 PerData8 K21 GND L21 PerAddr18 M21 VDD
J22 PerData7 K22 PerData22 L22 PerAddr19 M22 PerAddr20
J23 PerData6 K23 VDD L23 PCIXCap M23 GND
J24 ASGND K24 PerData21 L24 PerAddr22 M24 PCIXReset
Signals Listed by Ball Assignment (Sheet 3 of 6)
Ball Signal Name Ball Signal Name Ball Signal Name Ball Signal Name
440GX – Power PC 440GX Embedded Processor
AMCC 45
Revision 1.19 – December 19, 2008
Data Sheet
N01 PerAddr08 P01 DMAReq3 * R01 TrcTS6 * T01 DQS7
N02 GND P02 PerWE R02 VDD T02 SysErr
N03 PerAddr28 P03 TrcTS1 * R03 DMAReq0 T03 PerCS5
N04 VDD P04 GMCRxEr * R04 GND T04 TrcTS0 *
N05 DMAAck0 P05 PerR/W R05 TrcClk T05 TrcES4 *
N06 GND P06 DMAAck2 * R06 OVDD T06 TrcTS5 *
N07 PerReady * P07 DMAAck1 R07 TrcTS2 * T07 MemData61
N08 OVDD P08 TrcES3 * R08 GND T08 MemData56
N09 TrcES2 * P09 TrcTS3 * R09 TrcTS4 * T09 MemVRef2
N10 GND P10 SysReset R10 VDD T10 MemData38
N11 DMAReq2 * P11 DMAAck3 * R11 MemData42 T11 MemData37
N12 VDD P12 MemData28 R12 GND T12 MemData35
N13 GND P13 DM3 R13 VDD T13 MemData22
N14 IRQ04 * P14 GPIO11 * R14 MemData14 T14 MemVRef1
N15 VDD P15 EOT1/TC1 R15 GND T15 MemData18
N16 TrcBS0 * P16 EOT2/TC2 * R16 EOT0/TC0 T16 DM0
N17 GND P17 TrcBS1 * R17 OVDD T17 ExtReset
N18 IRQ00 * P18 IRQ07 * R18 PCIXReq5 T18 PerWBE0
N19 VDD P19 PCIXGnt5 R19 GND T19 PerAddr24
N20 IRQ08 * P20 IRQ02 * R20 PCIXReq3 T20 TrcBS2 *
N21 GND P21 TrcTS6 * R21 OVDD T21 TrcES0 *
N22 PCIXGnt2 P22 IRQ09 * R22 PCIXGnt4 T22 PerPar1
N23 OVDD P23 TrcES1 * R23 GND T23 PerPar0
N24 TRST P24 PerAddr23 R24 PerAddr25 T24 PerCS3
Signals Listed by Ball Assignment (Sheet 4 of 6)
Ball Signal Name Ball Signal Name Ball Signal Name Ball Signal Name
440GX – Power PC 440GX Embedded Processor
46 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
U01 TmrClk V01 MemData55 W01 MemData58 Y01 MemData51
U02 GND V02 UART0_DSR W02 OVDD Y02 MemData53
U03 PerCS7 V03 DM7 W03 MemData59 Y03 DM6
U04 OVDD V04 PerCS2 W04 GND Y04 DQS6
U05 MemData63 V05 Halt W05 MemData62 Y05 WE
U06 GND V06 MemData60 W06 VDD Y06 MemData46
U07 MemData57 V07 MemData54 W07 ECC3 Y07 MemData43
U08 VDD V08 MemClkOut0 W08 GND Y08 MemData47
U09 ECC4 V09 MemClkOut0 W09 ClkEn3 Y09 ClkEn2
U10 GND V10 MemAddr12 W10 SVDD Y10 MemData34
U11 MemData36 V11 MemAddr9 W11 MemData32 Y11 MemAddr11
U12 SVDD V12 MemData31 W12 GND Y12 MemData30
U13 GND V13 MemAddr8 W13 VDD Y13 MemData27
U14 MemData21 V14 MemData26 W14 BankSel1 Y14 MemAddr7
U15 SVDD V15 MemData19 W15 GND Y15 MemData23
U16 MemData04 V16 MemData09 W16 MemAddr10 Y16 MemData20
U17 GND V17 MemData05 W17 SVDD Y17 MemData10
U18 PerClk V18 IRQ10 * W18 MemData08 Y18 MemData13
U19 OVDD V19 PerWBE1 W19 GND Y19 MemAddr00
U20 PerPar3 V20 PerAddr29 W20 PerPar2 Y20 MemAddr02
U21 GND V21 PerAddr31 W21 VDD Y21 HoldAck *
U22 PerAddr26 V22 TCK W22 PerWBE2 Y22 TDO
U23 VDD V23 PerAddr30 W23 GND Y23 HoldReq *
U24 PerAddr27 V24 UART0_DCD W24 PerWBE3 Y24 TDI
Signals Listed by Ball Assignment (Sheet 5 of 6)
Ball Signal Name Ball Signal Name Ball Signal Name Ball Signal Name
440GX – Power PC 440GX Embedded Processor
AMCC 47
Revision 1.19 – December 19, 2008
Data Sheet
AA01 MemData48 AB01 No ball AC01 No ball AD01 No ball
AA02 GND AB02 MemData50 AC02 No ball AD02 No ball
AA03 MemData49 AB03 MemData52 AC03 ECC5 AD03 No ball
AA04 VDD AB04 ECC6 AC04 GND AD04 ECC7
AA05 DQS8 AB05 CAS AC05 DM8 AD05 BankSel3
AA06 GND AB06 ECC1 AC06 SVDD AD06 ECC2
AA07 DM5 AB07 ECC0 AC07 MemData44 AD07 RAS
AA08 SVDD AB08 MemData40 AC08 GND AD08 MemData41
AA09 DM4 AB09 MemData45 AC09 DQS5 AD09 BA1
AA10 GND AB10 ClkEn1 AC10 VDD AD10 MemData39
AA11 AMGND AB11 AMVDD for MemClk
PLL AC11 DQS4 AD11 BankSel2
AA12 VDD AB12 MemData29 AC12 GND AD12 MemData33
AA13 GND AB13 DQS3 AC13 SVDD AD13 MemData24
AA14 MemData16 AB14 DM2 AC14 DQS2 AD14 MemData25
AA15 SVDD AB15 BankSel0 AC15 GND AD15 MemData17
AA16 BA0 AB16 MemData11 AC16 DQS1 AD16 MemAddr5
AA17 GND AB17 MemData15 AC17 VDD AD17 ClkEn0
AA18 DM1 AB18 MemAddr6 AC18 MemData12 AD18 MemAddr4
AA19 VDD AB19 MemData07 AC19 GND AD19 MemData06
AA20 MemData03 AB20 MemAddr3 AC20 DQS0 AD20 MemAddr01
AA21 GND AB21 MemData01 AC21 SVDD AD21 MemData00
AA22 ExtAck * AB22 TMS AC22 MemData02 AD22 No ball
AA23 OVDD AB23 ExtReq * AC23 No ball AD23 No ball
AA24 BusReq * AB24 No ball AC24 No ball AD24 No ball
Signals Listed by Ball Assignment (Sheet 6 of 6)
Ball Signal Name Ball Signal Name Ball Signal Name Ball Signal Name
440GX – Power PC 440GX Embedded Processor
48 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Signal Description
The PPC440GX embedded controller is provided in a 552-ball, ball grid array package. The following tables
describe the package level pinout.
In the table “Signal Functional Description” on page 50, each I/O signal is listed along with a short description of its
function. Active-low signals (for example, RAS) are marked with an overline. Please see “Signals Listed
Alphabetically” on page 18 for the pin (ball) number to which each signal is assigned.
Multiplexed Signals
Some signals are multiplexed on the same pin so that the pin can be used for different functions. In most cases,
the signal names shown in this table are not accompanied by signal names that may be multiplexed on the same
pin. If you need to know what, if any, signals are multiplexed with a particular signal, look up the name in “Signals
Listed Alphabetically” on page 18. It is expected that in any single application a particular pin will always be
programmed to serve the same function. The flexibility of multiplexing allows a single chip to offer a richer pin
selection than would otherwise be possible.
Multipurpose Signals
In addition to multiplexing, some pins are also multi-purpose. For example, the EBC peripheral controller address
pins (PerAddr00:31) are used as outputs by the PPC440GX to broadcast an address to external slave devices
when the PPC440GX has control of the external bus. When during the course of normal chip operation an external
master gains ownership of the external bus, these same pins are used as inputs which are driven by the external
master and received by the EBC in the PPC440GX. In this example, the pins are also bidirectional, serving both as
inputs and outputs.
Multimode Signals
In some cases (for example, Ethernet) the function of a pin may vary with different modes of operation. When a pin
has multiple signal names assigned to distinguish different modes of operation, all of the names are shown.
Pin Summary
Group No. of Pins
Signal pins, non-multiplexed 343
Signal pins, multiplexed 63
Total Signal Pins 406
AxVDD 3
AxGnd 3
OVDD 27
SVDD 9
VDD 34
Gnd 70
Total Power Pins 146
Reserved 0
Total Pins 552
440GX – Power PC 440GX Embedded Processor
AMCC 49
Revision 1.19 – December 19, 2008
Data Sheet
Strapping Pins
One group of pins is used as strapped inputs during system reset. These pins function as strapped inputs only
during reset and are used for other functions during normal operation (see “Strapping” on page 90). Note that
these are not multiplexed pins since the function of the pins is not programmable.
440GX – Power PC 440GX Embedded Processor
50 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Signal Functional Description (Sheet 1 of 8)
Notes:
1. Receiver input has hysteresis
2. Must pull up (recommended value is 3kΩ to 3.3V)
3. Must pull down (recommended value is 1kΩ)
4. If not used, must pull up (recommended value is 3kΩ to 3.3V)
5. If not used, must pull down (recommended value is 1kΩ to GND)
6. Strapping input during reset; pull-up (recommended value is 3kΩ to 3.3V) or pull-down (recommended value is 1kΩ to GND)
required
Signal Name Description I/O Type Notes
PCI-X Interface
PCIXAD00:63 Address/Data bus (bidirectional). I/O 3.3V PCI
PCIXC0:7[BE0:7]PCI-X Command[Byte Enables].I/O 3.3V PCI
PCIXCap Capable of PCI-X operation. I 3.3V LVTTL 5
PCIX133Cap PCI-X devices are 133 MHz capable. O 3.3V PCI
PCIXClk
Provides timing to the PCI interface for PCI transactions.
Note: If the PCI-X interface is not being used, drive this pin with a
3.3V clock signal at a frequency between 1 and 66MHz
I 3.3V PCI
PCIXDevSel Indicates the driving device has decoded its address as the target
of the current access. I/O 3.3V PCI 4
PCIXFrame Driven by the current master to indicate beginning and duration of
an access. I/O 3.3V PCI 4
PCIXGnt0
Indicates that the specified agent is granted access to the bus.
When using an external PCI/PCI-X arbiter, connect the external
arbiter's Grant line to this signal.
I/O 3.3V PCI 4
PCIXGnt1 Indicates that the specified agent is granted access to the bus. I/O 3.3V PCI 4
PCIXGnt2:5 Indicates that the specified agent is granted access to the bus. O 3.3V PCI
PCIXIDSel Used as a chip select during configuration read and write
transactions. I 3.3V PCI 5
PCIXINT Level sensitive PCI interrupt. O 3.3V PCI
PCIXIRDY Indicates initiating agent’s ability to complete the current data
phase of the transaction. I/O 3.3V PCI 4
PCIXM66En Capable of 66MHz operation. I 3.3V LVTTL
w/pull-up 5
PCIXParHigh Even parity across PCIAD32:63 and PCIXC0:3[BE4:7]. I/O 3.3V PCI
PCIXParLow Even parity across PCIAD0:31 and PCIXC0:3[BE0:3]. I/O 3.3V PCI
PCIXPErr Reports data parity errors during all PCI transactions except a
Special Cycle. I/O 3.3V PCI 4
PCIXReq0
An indication to the PCI-X arbiter that the specified agent wishes
to use the bus. When using an external PCI/PCI-X arbiter, connect
the external arbiter's Request line to this signal.
I/O 3.3V PCI 4
PCIXReq1:5 An indication to the PCI-X arbiter that the specified agent wishes
to use the bus. I 3.3V PCI 4
PCIXReq64 Asserted by the current bus master, indicating a 64-bit transfer. I/O 3.3V PCI 4
PCIXAck64 Indicates the target can transfer data using 64 bits. I/O 3.3V PCI 4
PCIXReset Brings PCI device registers and logic to a consistent state. O 3.3V PCI
PCIXSErr Reports address parity errors, data parity errors on the Special
Cycle command, or other catastrophic system errors. I/O 3.3V PCI 4
PCIXStop Indicates the current target is requesting the master to stop the
current transaction. I/O 3.3V PCI 4
440GX – Power PC 440GX Embedded Processor
AMCC 51
Revision 1.19 – December 19, 2008
Data Sheet
PCIXTRDY Indicates the target agent’s ability to complete the current data
phase of the transaction. I/O 3.3V PCI 4
DDR SDRAM Interface
BA0:1 Bank Address supporting up to four internal banks. O 2.5V SSTL_2
BankSel0:3 Selects up to four external DDR SDRAM banks. O 2.5V SSTL_2
CAS Column Address Strobe. O 2.5V SSTL_2
ClkEn0:3 Clock Enable. One for each bank. O 2.5V SSTL_2
DM0:8 Memory write data byte lane masks. MEMDM8 is the byte lane
mask for the ECC byte lane. O 2.5V SSTL_2
DQS0:8 Byte lane data strobe. DQS8 is the data strobe for the ECC byte
lane. I/O 2.5V SSTL_2
ECC0:7 ECC check bits 0:7. I/O 2.5V SSTL_2
MemAddr00:12 Memory address bus. O 2.5V SSTL_2
MemClkOut0
MemClkOut0 Subsystem clock. O 2.5V SSTL_2
MemData00:63 Memory data bus. I/O 2.5V SSTL_2
MemVRef1:2 Memory reference voltage (SVREF) input. IVoltage Ref
Receiver
RAS Row Address Strobe. O 2.5V SSTL_2
WE Write Enable. O 2.5V SSTL_2
Ethernet Interface
EMCCD,
EMC1RxErr,
GMCGTxClk,
GMC0TxClk,
TBITxClk,
RTBI0TxClk
MII: Collision detection
RMII 1: Receive error
GMII: 1000Mbps Transmit clock
RGMII: Transmit clock
TBI: Transmit clock
RTBI: Transmit clock
I/O 3.3V tolerant
2.5V CMOS
EMCCrS,
EMC0CrSDV,
GMCTxD7,
GMC1TxD3,
TBITxD7,
RTBI1TxD3
MII: Carrier sense
RMII 0: Carrier sense data valid
GMII: Transmit data
RGMII 1: Transmit data
TBI: Transmit data
RTBI 1: Transmit data
I/O 3.3V tolerant
2.5V CMOS
EMCMDClk MII and RMII: Management data clock O 3.3V tolerant
2.5V CMOS
EMCMDIO MII and RMII: Transfer command and status information between
MII and PHY I/O 3.3V tolerant
2.5V CMOS
Signal Functional Description (Sheet 2 of 8)
Notes:
1. Receiver input has hysteresis
2. Must pull up (recommended value is 3kΩ to 3.3V)
3. Must pull down (recommended value is 1kΩ)
4. If not used, must pull up (recommended value is 3kΩ to 3.3V)
5. If not used, must pull down (recommended value is 1kΩ to GND)
6. Strapping input during reset; pull-up (recommended value is 3kΩ to 3.3V) or pull-down (recommended value is 1kΩ to GND)
required
Signal Name Description I/O Type Notes
440GX – Power PC 440GX Embedded Processor
52 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
EMCRxD0:3,
EMC0RxD0:1,
EMC1RxD0:1,
EMC0RxD,
EMC1RxD,
EMC2RxD,
EMC3RxD,
GMCTxD0:1,
GMC0TxD0:1,
TBITxD0:1,
RTBI0TxD0:1
MII: Receive data
RMII 0: Receive data
RMII 1: Receive data
SMII 0: Receive data
SMII 1: Receive data
SMII 2: Receive data
SMII 3: Receive data
GMII: Transmit data
RGMII 0: Transmit data
TBI: Transmit data
RTBI 0: Transmit data
I/O 3.3V tolerant
2.5V CMOS
EMCRxDV,
EMC1CrSDV,
GMCTxD4,
GMC1TxD0,
TBITxD4,
RTBI1TxD0
MII: Receive data valid
RMII 1: Carrier sense data valid
GMII: Transmit data
RGMII 1: Transmit data
TBI: Transmit data
RTBI 1: Transmit data
I/O 3.3V tolerant
2.5V CMOS
EMCRxClk,
GMCTxD5,
GMC1TxD1,
TBITxD5,
RTBI1TxD1
MII: Receive clock
GMII: Transmit data
RGMII 1: Transmit data
TBI: Transmit data
RTBI 1: Transmit data
I/O 3.3V tolerant
2.5V CMOS
EMCRxErr,
EMC0RxErr,
GMCTxD6,
GMC1TxD2,
TBITxD6,
RTBI1TxD2
MII: Receive error
RMII 0: Receive error
GMII: Transmit data
RGMII 1: Transmit data
TBI: Transmit data
RTBI 1: Transmit data
I/O 3.3V tolerant
2.5V CMOS
EMCTxClk,
EMCRefClk
MII: Transmit clock
RMII and SMII: Reference clock I3.3V tolerant
2.5V CMOS 5
EMCTxD0:3,
EMC0TxD0:1,
EMC1TxD0:1,
EMC0TxD,
EMC1TxD,
EMC2TxD,
EMC3TxD,
GMCTxD2:3,
GMC0TxD2:3,
TBITxD2:3,
RTBI0TxD2:3
MII: Transmit data
RMII 0: Transmit data
RMII 1: Transmit data
SMII 0: Transmit data
SMII 1: Transmit data
SMII 2: Transmit data
SMII 3: Transmit data
GMII: Transmit data
RGMII 0: Transmit data
TBI: Transmit data
RTBI 0: Transmit data
O3.3V tolerant
2.5V CMOS
EMCTxEn,
EMC0TxEn,
EMCSync
MII: Transmit data enabled
RMII 0: Transmit data enabled
SMII: Sync signal
O3.3V tolerant
2.5V CMOS
EMCTxErr,
EMC1TxEn,
GMCRxClk,
GMC0RxClk,
TBIRxClk0,
RTBI0RxClk
MII: Transmit error:
RMII: Transmit data enabled
GMII: Receive clock
RGMII: Receive clock
TBI: Receive clock 0
RTBI: Receive clock
I/O 3.3V tolerant
2.5V CMOS
GMCCD,
GMC1RxClk,
RTBI1RxClk
GMII: Collision detection
RGMII: Receive clock
RTBI: Receive clock
I3.3V tolerant
2.5V CMOS 5
Signal Functional Description (Sheet 3 of 8)
Notes:
1. Receiver input has hysteresis
2. Must pull up (recommended value is 3kΩ to 3.3V)
3. Must pull down (recommended value is 1kΩ)
4. If not used, must pull up (recommended value is 3kΩ to 3.3V)
5. If not used, must pull down (recommended value is 1kΩ to GND)
6. Strapping input during reset; pull-up (recommended value is 3kΩ to 3.3V) or pull-down (recommended value is 1kΩ to GND)
required
Signal Name Description I/O Type Notes
440GX – Power PC 440GX Embedded Processor
AMCC 53
Revision 1.19 – December 19, 2008
Data Sheet
GMCCrS,
GMC1TxClk,
RTBI1TxClk
GMII: Carrier sense
RGMII: Transmit clock
RTBI: Transmit clock
I/O 3.3V tolerant
2.5V CMOS
GMCRefClk GMII, RGMII, TBI and RTBI: Gigabit reference clock I 3.3V tolerant
2.5V CMOS 5
GMCRxD0:3,
GMC0RxD0:3,
TBIRxD0:3,
RTBI0RxD0:3
GMII: Receive data
RGMII: Receive data
TBI: Receive data
RTBI: Receive data
I3.3V tolerant
2.5V CMOS
GMCRxD4:7,
GMC1RxD0:3,
TBIRxD4:7,
RTBI1RxD0:3
GMII: Receive data
RGMII: Receive data
TBI: Receive data
RTBI: Receive data
I3.3V tolerant
2.5V CMOS
GMCRxDV,
GMC0RxCtl,
TBIRxD8,
RTBI0RxD4
GMII: Receive data valid
RGMII: Receive control
TBI: Receive data
RTBI: Receive data
I3.3V tolerant
2.5V CMOS
GMCRxEr,
GMC1RxCtl,
TBIRxD9,
RTBI1RxD4
GMII: Receive error
RGMII: Receive control
TBI: Receive data
RTBI: Receive data
I/O 3.3V tolerant
2.5V CMOS
GMCTxEn,
GMC0TxCtl,
TBITxD8,
RTBI0TxD4
GMII: Transmit data enable
RGMII: Transmit control
TBI: Transmit data
RTBI: Transmit data
O3.3V tolerant
2.5V CMOS
GMCTxEr,
GMC1TxCtl,
TBITxD9,
RTBI1TxD4
GMII: Transmit error
RGMII: Transmit control
TBI: Transmit data
RTBI: Transmit data
O3.3V tolerant
2.5V CMOS 6
GMCTxClk
TBIRxClk1
GMII: 10/100Mbps Transmit clock
TBI: Receive clock 1 I/O 3.3V LVTTL 5
External Slave Peripheral Interface
DMAAck0:3 Used by the PPC440GX to indicate that data transfers have
occurred. O3.3V tolerant
2.5V CMOS
DMAReq0:3 Used by slave peripherals to indicate they are prepared to transfer
data. I3.3V tolerant
2.5V CMOS 1, 5
EOT0:3/TC0:3 End Of Transfer/Terminal Count. I/O 3.3V tolerant
2.5V CMOS 1, 5
PerAddr00:31
Peripheral address bus used by PPC440GX when not in external
master mode, otherwise used by external master.
Note: PerAddr00 is the most significant bit (msb) on this bus.
I/O 3.3V LVTTL 1
PerWBE0:3 External peripheral data bus byte enables. I/O 3.3V LVTTL 1, 2
PerBLast Used by either the peripheral controller, DMA controller, or
external master to indicates the last transfer of a memory access. I/O 3.3V LVTTL 1, 4
PerCS0:7 External peripheral device select. O 3.3V LVTTL 2
Signal Functional Description (Sheet 4 of 8)
Notes:
1. Receiver input has hysteresis
2. Must pull up (recommended value is 3kΩ to 3.3V)
3. Must pull down (recommended value is 1kΩ)
4. If not used, must pull up (recommended value is 3kΩ to 3.3V)
5. If not used, must pull down (recommended value is 1kΩ to GND)
6. Strapping input during reset; pull-up (recommended value is 3kΩ to 3.3V) or pull-down (recommended value is 1kΩ to GND)
required
Signal Name Description I/O Type Notes
440GX – Power PC 440GX Embedded Processor
54 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
PerData00:31
Peripheral data bus used by PPC440GX when not in external
master mode, otherwise used by external master.
Note: PerData00 is the most significant bit (msb) on this bus.
I/O 3.3V LVTTL 1
PerOE
Used by either peripheral controller or DMA controller depending
upon the type of transfer involved. When the PPC440GX is the
bus master, it enables the selected device to drive the bus.
O 3.3V LVTTL 2
PerPar0:3 External peripheral data bus byte parity. I/O 3.3V LVTTL 1
PerReady Used by a peripheral slave to indicate it is ready to transfer data. I 3.3V LVTTL
PerR/W
Used by the PPC440GX when not in external master mode, as
output by either the peripheral controller or DMA controller
depending upon the type of transfer involved. High indicates a
read from memory, low indicates a write to memory.
Otherwise, it used by the external master as an input to indicate
the direction of transfer.
I/O 3.3V LVTTL 1, 2
PerWE Write Enable. Low when any of the four PerWBE0:3 signals are
low. O 3.3V LVTTL 2
External Master Peripheral Interface
BusReq Bus Request. Used when the PPC440GX needs to regain control
of peripheral interface from an external master. O 3.3V LVTTL
ExtAck External Acknowledgement. Used by the PPC440GX to indicate
that a data transfer occurred. O 3.3V LVTTL
ExtReq External Request. Used by an external master to indicate it is
prepared to transfer data. I 3.3V LVTTL 1, 4
ExtReset Peripheral Reset. Used by an external master and by
synchronous peripheral slaves. O 3.3V LVTTL
HoldAck Hold Acknowledge. Used by the PPC440GX to transfer ownership
of peripheral bus to an external master. O 3.3V LVTTL
HoldReq Hold Request. Used by an external master to request ownership
of the peripheral bus. I 3.3V LVTTL 1, 5
PerClk Peripheral Clock. Used by an external master and by synchronous
peripheral slaves. O 3.3V LVTTL
PerErr External Error. Used as an input to record external master errors
and external slave peripheral errors. I/O 3.3V LVTTL 1, 5
UART Peripheral Interface
UARTSerClk
Serial clock input that provides an alternative to the internally
generated serial clock. Used in cases where the allowable
internally generated clock rates are not satisfactory. This input can
be individually connected to either or both UART0 and UART1.
I 3.3V LVTTL 1, 4
UART0_Rx UART0 Receive data. I 3.3V LVTTL 1, 4
UART0_Tx UART0 Transmit data. O 3.3V LVTTL 4
UART0_DCD UART0 Data Carrier Detect. I 3.3V LVTTL 6
UART0_DSR UART0 Data Set Ready. I 3.3V LVTTL 6
UART0_CTS UART0 Clear To Send. I 3.3V LVTTL 1, 4
Signal Functional Description (Sheet 5 of 8)
Notes:
1. Receiver input has hysteresis
2. Must pull up (recommended value is 3kΩ to 3.3V)
3. Must pull down (recommended value is 1kΩ)
4. If not used, must pull up (recommended value is 3kΩ to 3.3V)
5. If not used, must pull down (recommended value is 1kΩ to GND)
6. Strapping input during reset; pull-up (recommended value is 3kΩ to 3.3V) or pull-down (recommended value is 1kΩ to GND)
required
Signal Name Description I/O Type Notes
440GX – Power PC 440GX Embedded Processor
AMCC 55
Revision 1.19 – December 19, 2008
Data Sheet
UART0_DTR UART0 Data Terminal Ready. O 3.3V LVTTL 4
UART0_RTS UART0 Request To Send. O 3.3V LVTTL 4
UART0_RI UART0 Ring Indicator. I 3.3V LVTTL 1, 4
UART1_Rx UART1 Receive data. I/O 3.3V LVTTL 1, 4
UART1_Tx UART1 Transmit data. I/O 3.3V LVTTL 1, 4
UART1_DSR/CTS UART1 Data Set Ready or Clear To Send. The choice is
determined by a DCR register bit setting. I/O 3.3V LVTTL 1, 4
UART1_RTS/DTR UART1 Request To Send or Data Terminal Ready. The choice is
determined by a DCR register bit setting. I/O 3.3V LVTTL 1, 4
IIC Peripheral Interface
IIC0SClk IIC0 Serial Clock. I/O 3.3V LVTTL 1, 2
IIC0SDA IIC0 Serial Data. I/O 3.3V LVTTL 1, 2
IIC1SClk IIC1 Serial Clock. I/O 3.3V IIC 1, 2
IIC1SDA IIC1 Serial Data. I/O 3.3V IIC 1, 2
Interrupts Interface
IRQ00:10 External interrupt Requests 0 through 10. I 3.3V LVTTL 1, 5
IRQ11:12 External interrupt Requests 11 through 12. I 3.3V PCI
IRQ13:17 External interrupt Requests 13 through 17. I 3.3V LVTTL
JTAG Interface
TCK Test Clock. I 3.3V LVTTL
w/pull-up 1
TDI Test Data In. I 3.3V LVTTL
w/pull-up 4
TDO Test Data Out. O 3.3V LVTTL
TMS Test Mode Select. I 3.3V LVTTL
w/pull-up 1
TRST
Test Reset. During chip power-up, this signal must be low from the
start of VDD ramp-up until at least 16 SysClk cycles after VDD is
stable in order to initialize the JTAG controller.
I3.3V LVTTL
w/pull-up 5
Signal Functional Description (Sheet 6 of 8)
Notes:
1. Receiver input has hysteresis
2. Must pull up (recommended value is 3kΩ to 3.3V)
3. Must pull down (recommended value is 1kΩ)
4. If not used, must pull up (recommended value is 3kΩ to 3.3V)
5. If not used, must pull down (recommended value is 1kΩ to GND)
6. Strapping input during reset; pull-up (recommended value is 3kΩ to 3.3V) or pull-down (recommended value is 1kΩ to GND)
required
Signal Name Description I/O Type Notes
440GX – Power PC 440GX Embedded Processor
56 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
System Interface
SysClk Main system clock input. Clock 3.3V LVTTL
SysErr Set to 1 when a machine check is generated. O 3.3V LVTTL
SysReset
Main system reset. External logic can drive this bidirectional pin
low (minimum of 16 cycles) to initiate a system reset. A system
reset can also be initiated by software. The signal is implemented
as an open-drain output (two states; 0 or open circuit).
During chip power-up, this signal must be low from the start of VDD
ramp-up until at least 16 SysClk cycles after VDD is stable.
I/O 3.3V LVTTL 1, 2
TmrClk Processor timer external input clock. I 3.3V LVTTL
Halt Halt from external debugger. I 3.3V LVTTL 1, 4
GPIO00:31 General purpose I/O 0 through 10. To access these functions,
software must set DCR register bits. I/O 3.3V LVTTL
TestEn Test Enable. I 3.3V tolerant
2.5V CMOS 3
RcvrInh Receiver Inhibit. Active only when TestEn is active. I 3.3V LVTTL
RefVEn Reference Voltage Enable. Do not connect for normal operation.
Pull up for Boundary Scan Description Language (BSDL) testing. I3.3V LVTTL
w/pull-down
DrvrInh2 Driver Inhibit. Used for test purposes only. Tie up for normal
operation I3.3V LVTTL
w/pull-up 2
Signal Functional Description (Sheet 7 of 8)
Notes:
1. Receiver input has hysteresis
2. Must pull up (recommended value is 3kΩ to 3.3V)
3. Must pull down (recommended value is 1kΩ)
4. If not used, must pull up (recommended value is 3kΩ to 3.3V)
5. If not used, must pull down (recommended value is 1kΩ to GND)
6. Strapping input during reset; pull-up (recommended value is 3kΩ to 3.3V) or pull-down (recommended value is 1kΩ to GND)
required
Signal Name Description I/O Type Notes
440GX – Power PC 440GX Embedded Processor
AMCC 57
Revision 1.19 – December 19, 2008
Data Sheet
Trace Interface
TrcBS0:2 Trace branch execution status. I/O 3.3V LVTTL
TrcClk Trace data capture clock, runs at 1/4 the frequency of the
processor. O 3.3V LVTTL
TrcES0:4 Trace Execution Status is presented every fourth processor clock
cycle. I/O 3.3V LVTTL
TrcTS0:5
(multiplexed with GPIO signals)
Additional information on trace execution and branch status.
Note: The trace signals, TrcTS0:6, are duplicated on two sets of
chip balls and are multiplexed with other signals in both cases.
This allows users to choose which set of multiplexed signals they
wish to use along with the TrcTS0:6 signals. The trace signals in
this set are primary signals.
I/O 3.3V tolerant
2.5V CMOS
TrcTS1:5
(multiplexed with EBC signals)
Additional information on trace execution and branch status.
Note: The trace signals in this set are secondary signals. I/O 3.3V LVTTL
TrcTS6
(multiplexed with EBC and
Ethernet signals)
Additional information on trace execution and branch status.
Note: This trace signal is the primary signal. I/O 3.3V LVTTL
Power Pins
AxGND PLL (analog) voltage ground. na na
GND Ground. na na
AxVDD
1.5V—Filtered voltages input for PLLs (analog circuits)
Note: A separate filter for each of the three voltages is
recommended.
na na
OVDD 3.3V supply—I/O (except DDR SDRAM, Ethernet) na na
SVDD 2.5V supply—DDR SDRAM, Ethernet na na
VDD 1.5V supply—Logic voltage. na na
Signal Functional Description (Sheet 8 of 8)
Notes:
1. Receiver input has hysteresis
2. Must pull up (recommended value is 3kΩ to 3.3V)
3. Must pull down (recommended value is 1kΩ)
4. If not used, must pull up (recommended value is 3kΩ to 3.3V)
5. If not used, must pull down (recommended value is 1kΩ to GND)
6. Strapping input during reset; pull-up (recommended value is 3kΩ to 3.3V) or pull-down (recommended value is 1kΩ to GND)
required
Signal Name Description I/O Type Notes
440GX – Power PC 440GX Embedded Processor
58 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Absolute Maximum Ratings
The absolute maximum ratings below are stress ratings only. Operation at or beyond these maximum ratings can cause
permanent damage to the device. None of the performance specification contained in this document are guaranteed when
operating at these maximum ratings.
Characteristic Symbol Value Unit Notes
Supply Voltage (Internal Logic) VDD 0 to +1.65 V
Supply Voltage (I/O Interface, except DDR SDRAM) OVDD 0 to +3.6 V
PLL Supply Voltages AxVDD 0 to +1.65 V 1
Supply Voltage (DDR SDRAM Logic) SVDD 0 to +2.7 V
Input Voltage (3.3V LVTTL receivers) VIN 0 to +3.6 V
Storage Temperature Range TSTG -55 to +150 °C
Case Temperature under bias TC-40 to +120 °C2
Notes:
1. The analog voltages used for the on-chip PLLs can be derived from the logic voltage, but must be filtered before entering the
PPC440GX. A separate filter, as shown below, is recommended for each voltage:
2. This value is not a specification of the operational temperature range; it is a stress rating only.
VDD
C
AxVDD
L
L – SMT ferrite bead chip, Murata BLM31A700S or equivalent.
C – 0.1μF ceramic
AxGND
440GX – Power PC 440GX Embedded Processor
AMCC 59
Revision 1.19 – December 19, 2008
Data Sheet
Package Thermal Specifications
Thermal resistance values for the CBGA and PBGA packages in a convection environment are as follows:
Parameter Symbol Package
Airflow
ft/min (m/sec) Unit Notes
0 (0) 100 (0.51) 200 (1.02)
Junction-to-case thermal resistance θJC
Ceramic <0.1 <0.1 <0.1 °C/W 1
Plastic 1.2 1.2 1.2 °C/W 1, 3
Case-to-ambient thermal resistance (w/o heat
sink) θCA
Ceramic 18.9 17.7 16.3 °C/W 2
Plastic 20.8 °C/W 2, 3
Range
Min Nom Max
Junction-to-ball (typical) θJB
Ceramic 1.5 2.2 °C/W 4
Plastic 8.2 °C/W
Notes:
1. Case temperature, TC, is measured at top center of case surface with device soldered to circuit board.
2. The case-to-ambient thermal resistance is measured in a JEDEC JESD51-6 standard environment; and may not accurately predict
thermal performance in production equipment environments. The operational case temperature must be maintained.
3. Modeled on standard JEDEC 2S2P card, 50x50mm
4. 1.5 °C/W is the theoretical θJB using an infinite heat sink. The larger number applies to the module mounted on a 1.8mm thick, 2P card
using 1oz. copper power planes, with an effective heat transfer area of 75mm2.
440GX – Power PC 440GX Embedded Processor
60 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Heat Sink Mounting Information (Ceramic Package Only)
Proper thermal design is primarily dependent upon multiple system-level effects; that is, the effects of the heat
sink, the air flow, and the thermal interface material. To reduce the die-junction temperature, heat sinks may be
attached to the package by several methods: adhesive, spring clips to the printed-circuit board or package, or a
mounting clip and screw assembly. When attaching heat sinks, it is important to avoid placing excessive
mechanical stress on bonding of the chip to the substrate and the package to the board.
Heat Sink Attached With Spring Clip
Heat Sink Attached With Adhesive
Important: All of the guidelines indicated in the above diagrams must be evaluated and adjusted to account for the
shock and vibration effects of any particular application.
Heat sink
Thermal grease
Printed
circuit
board
CBGA
package
Heat sink
Heat sink clip
Printed
circuit
board
CBGA
package
Spring clip to board
Spring clip to package
Thermal grease
Heat sink clip Heat sink clip
Heat sink clip
Static compression (spring force)—2.27kg maximum Static compression (spring force)—2.27kg maximum1
Note 1: Force is limited by allowable compression on the die.
Allowable package compression force is 4.4kg.
Heat sink
Printed
circuit
board
CBGA
package
Adhesive
Heat sink
Printed
circuit
board
CBGA
package
Adhesive
Heat sink weight force—60g maximum
Weight
force
Weight
force
440GX – Power PC 440GX Embedded Processor
AMCC 61
Revision 1.19 – December 19, 2008
Data Sheet
Recommended DC Operating Conditions
Device operation beyond the conditions specified is not recommended. Extended operation beyond the recommended
conditions can affect device reliability.
Parameter Symbol Minimum Typical Maximum Unit Notes
Logic Supply Voltage (500MHz Rev A and 533MHz) VDD +1.4 +1.5 +1.6 V 4
Logic Supply Voltage (667MHz and 800MHz) VDD +1.5 +1.55 +1.6 V 4
I/O Supply Voltage OVDD +3.0 +3.3 +3.6 V 4
DDR SDRAM Supply Voltage (DDR clock up to 166MHz) SVDD +2.3 +2.5 +2.7 V 4
DDR SDRAM Supply Voltage (DDR clock = 200MHz) SVDD +2.5 +2.6 +2.7 V 4
PLL Supply Voltages (500MHz Rev A and 533MHz) AxVDD +1.4 +1.5 +1.6 V 3
PLL Supply Voltage (667MHz and 800MHz) AxVDD +1.5 +1.55 +1.6 V 3
DDR SDRAM Reference Voltage SVREF +1.15 +1.25 +1.35 V 3
Input Logic High (2.5V SSTL)
VIH
SVREF+0.18 SVDD+0.3 V2
Input Logic High (2.5V CMOS, 3.3V tolerant receiver) 1.7 V
Input Logic High (3.3V PCI-X) 0.5OVDD OVDD+0.5 V1
Input Logic High (3.3V LVTTL) +2.0 +3.6 V
Input Logic Low (2.5V SSTL)
VIL
-0.3 SVREF-0.18 V
Input Logic Low (2.5V CMOS, 3.3V tolerant receiver) 0.7 V
Input Logic Low (3.3V PCI-X) -0.5 0.35OVDD V1
Input Logic Low (3.3V LVTTL) 0 +0.8 V
Output Logic High (2.5V SSTL)
VOH
+1.95 SVDD V
Output Logic High (2.5V CMOS, 3.3V tolerant receiver) 2.0 V
Output Logic High (3.3V PCI-X) 0.9OVDD OVDD V1
Output Logic High (3.3V LVTTL) +2.4 OVDD V
Output Logic Low (2.5V SSTL)
VOL
00.55V
Output Logic Low (2.5V CMOS, 3.3V tolerant receiver) 0.4 V
Output Logic Low (3.3V PCI-X) 0.1OVDD V1
Output Logic Low (3.3V LVTTL) 0 +0.4 V
Input Leakage Current (No pull-up or pull-down) IIL1 00
μA
Input Leakage Current for Pull-Down IIL2 0 (LPDL) 200 (MPUL) μA5
Input Leakage Current for Pull-Up IIL3 -150 (LPDL) 0 (MPUL) μA5
Input Max Allowable Overshoot (3.3V LVTTL) VIMAO +3.9 V
Input Max Allowable Undershoot (3.3V LVTTL) VIMAU -0.6 V
440GX – Power PC 440GX Embedded Processor
62 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Output Max Allowable Overshoot (3.3V LVTTL) VOMAO +3.9 V
Output Max Allowable Undershoot (3.3V LVTTL) VOMAU3 -0.6 V
Case Temperature rating for C package and S package TC-40 +85 °C6
Case Temperature rating E for C package TC-40 +105 °C6
Case Temperature rating E for F package TC-40 +100 °C6
Notes:
1. PCI-X drivers meet PCI-X specifications.
2. SVREF = SVDD/2
3. The analog voltages used for the on-chip PLLs can be derived from the logic voltage, but must be filtered before entering the
PPC440GX. See “Absolute Maximum Ratings” on page 58.
4. There are no OVDD, VDD, or SVDD power supply power-up sequence requirements. However, external voltage should not be applied
to the chip I/O pins before OVDD is applied to the chip. A power-down cycle should complete (OVDD and VDD should both be below
0.4V) before a new power- up cycle is started.
5. LPDL is least positive down level; MPUL is most positive up level.
6. Case temperature, TC, is measured at top center of case surface with device soldered to circuit board.
Input Capacitance
Parameter Symbol Maximum Unit Notes
Group 1 (2.5V SSTL I/O) CIN1 12 pF
Group 2 (3.3V LVTTL I/O) CIN2 12 pF
Group 3 (PCI-X I/O) CIN3 12 pF
Group 4 (Receivers) CIN4 9pF
Group 5 (3.3V tolerant CMOS I/O) CIN5 16 pF
Recommended DC Operating Conditions (Continued)
Device operation beyond the conditions specified is not recommended. Extended operation beyond the recommended
conditions can affect device reliability.
Parameter Symbol Minimum Typical Maximum Unit Notes
440GX – Power PC 440GX Embedded Processor
AMCC 63
Revision 1.19 – December 19, 2008
Data Sheet
Test Conditions
Clock timing and switching characteristics are specified in accordance with operating
conditions shown in the table “Recommended DC Operating Conditions.” AC
specifications are characterized with VDD = 1.5V, TC = +85 °C and a 10pF test load as
shown in the figure to the right.
DC Power Supply Loads
Parameter Symbol Frequency (MHz) Typical Maximum Unit Notes
VDD active operating current IDD
533 1.37 1.69 A 2
667 1.49 1.8 A 2
800 1.77 2.2 A 2, 3
OVDD active operating current IODD
533 58 111 mA 2
667 58 111 mA 2
800 58 111 mA 2, 3
SVDD active operating current ISDD
533 544 749 mA 2
667 568 837 mA 2
800 680 940 mA 2, 3
AxVDD input current IADD 33 mA 1, 2
Notes:
1. See “Absolute Maximum Ratings” on page 58 for filter recommendations.
2. The maximum current values listed above are not guaranteed to be the highest obtainable. These values are dependent on many factors
including the type of applications running, clock rates, use of internal functional capabilities, external interface usage, case temperature,
and the power supply voltages. Your specific application can produce significantly different results. VDD (logic) current and power are
primarily dependent on the applications running and the use of internal chip functions (DMA, PCI, Ethernet, and so on). OVDD (I/O)
current and power are primarily dependent on the capacitive loading, frequency, and utilization of the external buses. The following
information provides details about the conditions under which the listed values were obtained:
a. In general, the values are measured using a PPC440GX Evaluation Board set for Ethernet mode 4, PCI-X running at 100MHz with
an Intel Pro 1000, an Agilent Test card, an EBMI test card, a UART wrap plug, and one 128MB Micron DIMM while running
applications designed to maximize CPU power consumption. An external PCI master heavily loads the PCI bus with transfers
targeting SDRAM, while the internal DMA controller further increases SDRAM bus traffic.
System clock rates are set as follows: SysClk = 33MHz, CPU = 667MHz, PLB = 167MHz, and OPB = EBC = 83MHz.
b. Typical current is characterized at VDD = +1.5V, OVDD = +3.3V, SVDD = +2.5V, and TC = +47°C.
c. Maximum current is characterized at VDD = +1.6V, OVDD = +3.6V, SVDD = +2.7V, and TC = +85°C.
3. Estimated values.
Output
Pin
10pF
C
440GX – Power PC 440GX Embedded Processor
64 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Clocking Specifications
Symbol Parameter Minimum Maximum Units Notes
SysClk Input
FCFrequency 33.33 83.33 MHz
TCPeriod 12 30 ns
TCS Edge stability (cycle-to-cycle jitter) – ±0.15 ns
TCH High time 40% of nominal period 60% of nominal period ns
TCL Low time 40% of nominal period 60% of nominal period ns
Note: Input slew rate ≥ 1V/ns
PLL VCO
FCFrequency 600 1334 MHz
TCPeriod 0.75 1.66 ns
Processor Clock (CPU Clock)
FCFrequency 333 800 MHz 1
TCPeriod 1.25 3 ns
MemClkOut and PLB
FC
Frequency—533, 667, 800MHz
Rev C
Frequency—800MHz Rev F
100
100
166.66
200
MHz
TC
Period—533, 667, 800MHz Rev C
Period—800MHz Rev F
6
5
10
10 ns
TCH High time 45% of nominal period 55% of nominal period ns
OPB Clock
FCFrequency 66.66 83.33 MHz 2
TCPeriod 12 15 ns 2
MAL Clock
FCFrequency 83.33 100 MHz 3
TCPeriod 10 12 ns 3
Notes:
1. The maximum supported processor clock frequency for any part is specified in the part number (see “Ordering and PVR Information”
on page 4).
2. In order to support 1Gbps Ethernet data rate, the minimum OPB clock frequency is 66.66Mhz. If the Ethernet application is limited to
100Mbps, the minimum OPB clock frequency is 33.33Mhz.
3. In order to support 1Gbps Ethernet data rate, the minimum MAL clock frequency is 83.33Mhz. If the Ethernet application is limited to
100Mbps, the minimum MAL clock frequency is 33.33Mhz
440GX – Power PC 440GX Embedded Processor
AMCC 65
Revision 1.19 – December 19, 2008
Data Sheet
Timing Waveform
TCL
TCH
TC
2.0V
1.5V
0.8V
440GX – Power PC 440GX Embedded Processor
66 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Spread Spectrum Clocking
Care must be taken when using a spread spectrum clock generator (SSCG) with the PPC440GX. This controller
uses a PLL for clock generation inside the chip. The accuracy with which the PLL follows the SSCG is referred to
as tracking skew. The PLL bandwidth and phase angle determine how much tracking skew there is between the
SSCG and the PLL for a given frequency deviation and modulation frequency. When using an SSCG with the
PPC440GX the following conditions must be met:
• The frequency deviation must not violate the minimum clock cycle time. Therefore, when operating the
PPC440GX with one or more internal clocks at their maximum supported frequency, the SSCG can only lower
the frequency.
• The maximum frequency deviation cannot exceed −3%, and the modulation frequency cannot exceed 40kHz.
In some cases, on-board PPC440GX peripherals impose more stringent requirements.
• Use the Peripheral Bus Clock for logic that is synchronous to the peripheral bus since this clock tracks the
modulation.
• Use the DDR SDRAM MemClkOut since it also tracks the modulation.
• For PCI-X and PCI 66 the maximum spread spectrum is -1% modulated between 30kHz and 33kHz.
Notes:
1. The serial port baud rates are synchronous to the modulated clock. The serial port has a tolerance of
approximately 1.5% on baud rate before framing errors begin to occur. The 1.5% tolerance assumes that
the connected device is running at precise baud rates.
2. Ethernet operation is unaffected.
3. IIC operation is unaffected.
Important: It is up to the system designer to ensure that any SSCG used with the PPC440GX meets the above
requirements and does not adversely affect other aspects of the system.
440GX – Power PC 440GX Embedded Processor
AMCC 67
Revision 1.19 – December 19, 2008
Data Sheet
Peripheral Interface Clock Timings
Parameter Min Max Units Notes
PCIXClk input frequency (asynchronous mode) – 133.33 MHz 2
PCIXClk period (asynchronous mode) 7.5 – ns
PCIXClk input high time 40% of nominal period 60% of nominal period ns
PCIXClk input low time 40% of nominal period 60% of nominal period ns
EMCMDClk output frequency – 2.5 MHz
EMCMDClk period 400 – ns
EMCMDClk output high time 160 – ns
EMCMDClk output low time 160 – ns
EMCTxClk input frequency MII(RMII) 2.5(5) 25(50) MHz
EMCTxClk period MII(RMII) 40(20) 400(200) ns
EMCTxClk input high time 35% of nominal period – ns
EMCTxClk input low time 35% of nominal period – ns
EMCRxClk input frequency MII(RMII) 2.5(5) 25(50) MHz
EMCRxClk period MII(RMII) 40(20) 400(200) ns
EMCRxClk input high time 35% of nominal period – ns
EMCRxClk input low time 35% of nominal period – ns
GMCRefClk input frequency – 125 MHz
GMCRefClk period 8 ns
GMCRefClk input high time 47% of nominal period 53% of nominal period ns
GMCRefClk input low time 47% of nominal period 53% of nominal period ns
PerClk output frequency (for ext. master or sync. slaves) 33.33 83.33 MHz
PerClk period 12 30 ns
PerClk output high time 50% of nominal period 66% of nominal period ns
PerClk output low time 33% of nominal period 50% of nominal period ns
UARTSerClk input frequency – 1000/(2TOPB1+2ns) MHz 1
UARTSerClk period 2TOPB+2 –ns1
UARTSerClk input high time TOPB+1 –ns1
UARTSerClk input low time TOPB+1 –ns1
440GX – Power PC 440GX Embedded Processor
68 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
TmrClk input frequency – 100 MHz
TmrClk period 10 – ns
TmrClk input high time 40% of nominal period 60% of nominal period ns
TmrClk input low time 40% of nominal period 60% of nominal period ns
Notes:
1. TOPB is the period in ns of the OPB clock. The internal OPB clock runs at an integral divisor ratio of the frequency of the
PLB clock. The maximum OPB clock frequency is 83.33 MHz. Refer to the Clocking chapter of the PPC440GX Embedded
Processor User’s Manual for details.
2. When the PCI-X interface is used to support a legacy PCI interface, the maximum PCIXClk frequency is 66.66MHz.
Peripheral Interface Clock Timings (Continued)
Parameter Min Max Units Notes
440GX – Power PC 440GX Embedded Processor
AMCC 69
Revision 1.19 – December 19, 2008
Data Sheet
Input Setup and Hold Waveform
Output Delay and Float Timing Waveform
Clock
TIS TIH
min min
Inputs
Valid
Valid
Clock
Outputs
Valid
TOH min
TOV max
TOV max
TOH min
TOV max
TOH min
Float (High-Z)
High (Drive)
Low (Drive)
440GX – Power PC 440GX Embedded Processor
70 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Input Setup and Hold Waveform for RGMII Signals
Output Delay and Hold Timing Waveform for RGMII Signals
GMCnRxClk
TIS TIH
min min
Inputs
Valid
Valid
TIS TIH
min min
1.25V
RGMII 1000Mb timing is with reference to the raising and falling edge of GMCnRxClk.
RGMII 10/100Mb timing is with reference only to the raising edge of GMCnRxClk.
Valid
GMCnTxClk
Outputs
TOHmin
TOV max
Float (High-Z)
High (Drive)
Low (Drive)
Valid Valid Valid
TOHmin
TOV max
1.25V
RGMII 1000Mb timing is with reference to the raising and falling edge of GMCnTxClk.
RGMII 10/100Mb timing is with reference only to the raising edge of GMCnTxClk.
440GX – Power PC 440GX Embedded Processor
AMCC 71
Revision 1.19 – December 19, 2008
Data Sheet
I/O Specifications—All Speeds (Sheet 1 of 7)
Notes:
1. Ethernet interface meets timing requirements as defined by IEEE 802.3 standard.
2. PCI-X timings are for asynchronous operation up to 133MHz. PCI-X input setup time requirement is 1.2ns for 133MHz and
1.7ns for 66MHz. PCI timings (in parentheses) are for asynchronous operation up to 66MHz. PCI output hold time
requirement is 1ns for 66MHz and 2ns for 33MHz.
3. The clock frequency for RMII operation is 50MHz ± 100ppm.
4. The clock frequency for SMII operation is 125MHz ± 100ppm.
5. These are DDR signals that can change on both the positive and negative clock transitions.
Signal
Input (ns) Output (ns) Output Current (mA)
Clock Notes
Setup Time
(TIS min)
Hold Time
(TIH min)
Valid Delay
(TOV max)
Hold Time
(TOH min)
I/O H
(minimum)
I/O L
(minimum)
PCI-X Interface
PCIXAD00:63 Note 2 (3) 0.5 (0) 3.8 (6) 0.7 (Note 2) 0.5 1.5 PCIXClk 2
PCIXC3:0[BE3:0] Note 2 (3) 0.5 (0) 3.8 (6) 0.7 (Note 2) 0.5 1.5 PCIXClk 2
PCIXParLow Note 2 (3) 0.5 (0) 3.8 (6) 0.7 (Note 2) 0.5 1.5 PCIXClk 2
PCIParHigh Note 2 (3) 0.5 (0) 3.8 (6) 0.7 (Note 2) 0.5 1.5 PCIXClk 2
PCIXFrame Note 2 (3) 0.5 (0) 3.8 (6) 0.7 (Note 2) 0.5 1.5 PCIXClk 2
PCIXINT na na dc dc 0.5 1.5 PCIXClk async
PCIXIRDY Note 2 (3) 0.5 (0) 3.8 (6) 0.7 (Note 2) 0.5 1.5 PCIXClk 2
PCIXTRDY Note 2 (3) 0.5 (0) 3.8 (6) 0.7 (Note 2) 0.5 1.5 PCIXClk 2
PCIXStop Note 2 (3 0.5 (0) 3.8 (6) 0.7 (Note 2) 0.5 1.5 PCIXClk 2
PCIXDevSel Note 2 (3) 0.5 (0) 3.8 (6) 0.7 (Note 2) 0.5 1.5 PCIXClk 2
PCIXIDSel Note 2 (3) 0.5 (0) na na na na PCIXClk 2
PCIXPErr Note 2 (3) 0.5 (0) 3.8 (6) 0.7 (Note 2) 0.5 1.5 PCIXClk 2
PCIXSErr Note 2 (3) 0.5 (0) 3.8 (6) 0.7 (Note 2) 0.5 1.5 PCIXClk 2
PCIXClk dc dc na na na na async
PCIXReset na na na na na na PCIXClk
PCIXReq64 Note 2 (3) 0.5 (0) 3.8 (6) 0.7 (Note 2) 0.5 1.5 PCIXClk 2
PCIXAck64 Note 2 (3) 0.5 (0) 3.8 (6) 0.7 (Note 2) 0.5 1.5 PCIXClk 2
PCIXCap Note 2 (3) 0.5 (0) na na na na PCIXClk 2
PCIX133Cap 3.8 0.7 0.5 1.5 PCIXClk 2
PCIXM66En Note 2 (3) 0.5 (0) na na na na PCIXClk 2
PCIXReq0:5 Note 2 (3) 0.5 (0) na na na na PCIXClk 2
PCIXGnt0:5 na) na 3.8 (6) 0.7 (Note 2) 0.5 1.5 PCIXClk 2
440GX – Power PC 440GX Embedded Processor
72 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Ethernet MII Interface
EMCRxD0:3 4 1 na na 5.1 6.8 EMCRxClk 1
EMCRxDV 4 1 na na 5.1 6.8 EMCRxClk 1
EMCRxClk na na na na 5.1 6.8 1,
async
EMCRxErr 4 1 na na 5.1 6.8 EMCRxClk 1
EMCTxD0:3 na na 15 2 5.1 6.8 EMCTxClk 1
EMCTxEn na na 15 2 5.1 6.8 EMCTxClk 1
EMCTxClk na na na na na na 1,
async
EMCTxErr na na 15 2 5.1 6.8 EMCTxClk 1
EMCCrS na na 5.1 6.8 1,
async
EMCCD na na 5.1 6.8 1,
async
EMCMDIO 5.1 6.8 EMCMDClk 1
EMCMDClk na na na na 5.1 6.8 1,
async
Ethernet RMII Interface
EMC0RxD0:1 2 1 na na 5.1 6.8 EMCRefClk
EMC0RxErr 2 1 na na 5.1 6.8 EMCRefClk
EMC0CrSDV na na 5.1 6.8 EMCRefClk
EMC0TxD0:1 na na 11 2 5.1 6.8 EMCRefClk
EMC0:1TxEn na na 11 2 5.1 6.8 EMCRefClk
EMC1RxD0:1 na na 5.1 6.8 EMCRefClk
EMC1RxErr na na 5.1 6.8 EMCRefClk
EMC1CrSDV na na 5.1 6.8 EMCRefClk
EMC1TxD0:1 na na 11 2 5.1 6.8 EMCRefClk
EMCRefClk na na na na na na 3,
async
I/O Specifications—All Speeds (Sheet 2 of 7)
Notes:
1. Ethernet interface meets timing requirements as defined by IEEE 802.3 standard.
2. PCI-X timings are for asynchronous operation up to 133MHz. PCI-X input setup time requirement is 1.2ns for 133MHz and
1.7ns for 66MHz. PCI timings (in parentheses) are for asynchronous operation up to 66MHz. PCI output hold time
requirement is 1ns for 66MHz and 2ns for 33MHz.
3. The clock frequency for RMII operation is 50MHz ± 100ppm.
4. The clock frequency for SMII operation is 125MHz ± 100ppm.
5. These are DDR signals that can change on both the positive and negative clock transitions.
Signal
Input (ns) Output (ns) Output Current (mA)
Clock Notes
Setup Time
(TIS min)
Hold Time
(TIH min)
Valid Delay
(TOV max)
Hold Time
(TOH min)
I/O H
(minimum)
I/O L
(minimum)
440GX – Power PC 440GX Embedded Processor
AMCC 73
Revision 1.19 – December 19, 2008
Data Sheet
Ethernet SMII Interface
EMC0:1RxD 0.8 0.8 na na 5.1 6.8 EMCRefClk
EMC2:3RxD 0.8 0.8 na na 5.1 6.8 EMCRefClk
EMC0:1TxD na na 3.5 2 5.1 6.8 EMCRefClk
EMC2:3TxD na na 3.5 2 5.1 6.8 EMCRefClk
EMCRefClk na na na na na na 4,
async
Ethernet GMII Interface
GMCRxClk na na na na na na 1,
async
GMCRxD0:7 2 0 na na 5.1 6.8 GMCRxClk
GMCRxEr 2 0 na na 5.1 6.8 GMCRxClk
GMCRxDV 2 0 na na 5.1 6.8 GMCRxClk
GMCCrS na na 5.1 6.8 1,
async
GMCol na na 5.1 6.8 1,
async
GMCGTxClk na na na na na na 1,
async
GMCTxD0:7 na na 5.5 0.5 5.1 6.8 GMCGTxClk
GMCTxEr na na 5.5 0.5 5.1 6.8 GMCGTxClk
GMCTxEn na na 5.5 0.5 5.1 6.8 GMCGTxClk
I/O Specifications—All Speeds (Sheet 3 of 7)
Notes:
1. Ethernet interface meets timing requirements as defined by IEEE 802.3 standard.
2. PCI-X timings are for asynchronous operation up to 133MHz. PCI-X input setup time requirement is 1.2ns for 133MHz and
1.7ns for 66MHz. PCI timings (in parentheses) are for asynchronous operation up to 66MHz. PCI output hold time
requirement is 1ns for 66MHz and 2ns for 33MHz.
3. The clock frequency for RMII operation is 50MHz ± 100ppm.
4. The clock frequency for SMII operation is 125MHz ± 100ppm.
5. These are DDR signals that can change on both the positive and negative clock transitions.
Signal
Input (ns) Output (ns) Output Current (mA)
Clock Notes
Setup Time
(TIS min)
Hold Time
(TIH min)
Valid Delay
(TOV max)
Hold Time
(TOH min)
I/O H
(minimum)
I/O L
(minimum)
440GX – Power PC 440GX Embedded Processor
74 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Ethernet RGMII Interface
GMC0RxClk na na na na na na 1,
async
GMC0RxCtl 1 1 na na na na GMC0RxClk 4, 5
GMC0RxD0:3 1 1 na na 5.1 6.8 GMC0RxClk 4, 5
GMC0TxClk na na na na 5.1 6.8 1,
async
GMC0TxCtl na na 0.5 3.5 5.1 6.8 GMC0TxClk 4, 5
GMC0TxD0:3 na na 0.5 3.5 5.1 6.8 GMC0TxClk 4, 5
GMC1RxClk na na na na na na 1,
async
GMC1RxCtl 1 1 na na na na GMC1RxClk 4, 5
GMC1RxD0:3 1 1 na na 5.1 6.8 GMC1RxClk 4, 5
GMC1TxClk na na na na 5.1 6.8 1,
async
GMC1TxCtl na na 0.5 3.5 5.1 6.8 GMC1TxClk 4, 5
GMC1TxD0:3 na na 0.5 3.5 5.1 6.8 GMC1TxClk 4, 5
GMCRefClk na na na na na na async
Ethernet TBI Interface
TBIRxClk0 na na na na na na 1,
async
TBIRxClk1 na na na na na na 1,
async
TBIRxD0:9 2.5 1.5 na na 5.1 6.8 TBIRxClkx
TBITxClk na na na na na na 1,
async
TBITxD0:9 na na 6 1 5.1 6.8 TBITxClk
I/O Specifications—All Speeds (Sheet 4 of 7)
Notes:
1. Ethernet interface meets timing requirements as defined by IEEE 802.3 standard.
2. PCI-X timings are for asynchronous operation up to 133MHz. PCI-X input setup time requirement is 1.2ns for 133MHz and
1.7ns for 66MHz. PCI timings (in parentheses) are for asynchronous operation up to 66MHz. PCI output hold time
requirement is 1ns for 66MHz and 2ns for 33MHz.
3. The clock frequency for RMII operation is 50MHz ± 100ppm.
4. The clock frequency for SMII operation is 125MHz ± 100ppm.
5. These are DDR signals that can change on both the positive and negative clock transitions.
Signal
Input (ns) Output (ns) Output Current (mA)
Clock Notes
Setup Time
(TIS min)
Hold Time
(TIH min)
Valid Delay
(TOV max)
Hold Time
(TOH min)
I/O H
(minimum)
I/O L
(minimum)
440GX – Power PC 440GX Embedded Processor
AMCC 75
Revision 1.19 – December 19, 2008
Data Sheet
Ethernet RTBI Interface
RTBI0RxClk na na na na na na 1,
async
RTBI0RxD0:4 1 1 na na 5.1 6.8 RTBI0RxClk
RTBI0TxClk na na na na 5.1 6.8 1,
async
RTBI0TxD0:4 na na 3.5 5.1 5.1 6.8 RTBI0TxClk
RTBI1RxClk na na na na na na 1,
async
RTBI1RxD0:4 1 1 na na 5.1 6.8 RTBI1RxClk
RTBI1TxClk na na na na 5.1 6.8 1,
async
RTBI1TxD0:4 na na 3.5 5.1 5.1 6.8 RTBI1TxClk
GMCRefClk na na na na na na async
I/O Specifications—All Speeds (Sheet 5 of 7)
Notes:
1. Ethernet interface meets timing requirements as defined by IEEE 802.3 standard.
2. PCI-X timings are for asynchronous operation up to 133MHz. PCI-X input setup time requirement is 1.2ns for 133MHz and
1.7ns for 66MHz. PCI timings (in parentheses) are for asynchronous operation up to 66MHz. PCI output hold time
requirement is 1ns for 66MHz and 2ns for 33MHz.
3. The clock frequency for RMII operation is 50MHz ± 100ppm.
4. The clock frequency for SMII operation is 125MHz ± 100ppm.
5. These are DDR signals that can change on both the positive and negative clock transitions.
Signal
Input (ns) Output (ns) Output Current (mA)
Clock Notes
Setup Time
(TIS min)
Hold Time
(TIH min)
Valid Delay
(TOV max)
Hold Time
(TOH min)
I/O H
(minimum)
I/O L
(minimum)
440GX – Power PC 440GX Embedded Processor
76 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Internal Peripheral Interface
IIC0SClk na na na na 15.3 10.2
IIC0SDA 15.3 10.2
IIC1SClk na na na na 15.3 10.2
IIC1SDA 15.3 10.2
UARTSerClk na na na na na na
UART0_Rx na na na na
UART0_Tx na na 10.3 7.1
UART0_DCD na na na na
UART0_DSR na na na na
UART0_CTS na na na na
UART0_DTR na na 10.3 7.1
UART0_RI na na na na
UART0_RTS na na 10.3 7.1
UART1_Rx na na na na
UART1_Tx na na 10.3 7.1
UART1_DSR/CTS na na na na
UART1_RTS/DTR na na 10.3 7.1
Interrupts Interface
IRQ00:17 na na
JTAG Interface
TDI na na async
TMS na na async
TDO 15.3 10.2 async
TCK na na async
TRST na na async
I/O Specifications—All Speeds (Sheet 6 of 7)
Notes:
1. Ethernet interface meets timing requirements as defined by IEEE 802.3 standard.
2. PCI-X timings are for asynchronous operation up to 133MHz. PCI-X input setup time requirement is 1.2ns for 133MHz and
1.7ns for 66MHz. PCI timings (in parentheses) are for asynchronous operation up to 66MHz. PCI output hold time
requirement is 1ns for 66MHz and 2ns for 33MHz.
3. The clock frequency for RMII operation is 50MHz ± 100ppm.
4. The clock frequency for SMII operation is 125MHz ± 100ppm.
5. These are DDR signals that can change on both the positive and negative clock transitions.
Signal
Input (ns) Output (ns) Output Current (mA)
Clock Notes
Setup Time
(TIS min)
Hold Time
(TIH min)
Valid Delay
(TOV max)
Hold Time
(TOH min)
I/O H
(minimum)
I/O L
(minimum)
440GX – Power PC 440GX Embedded Processor
AMCC 77
Revision 1.19 – December 19, 2008
Data Sheet
System Interface
SysClk na na na na
TmrClk na na na na async
SysReset na na async
Halt na na na na async
SysErr na na 10.3 7.1 async
TestEn na na na na async
DrvrInh2 na na na na
GPIO00:31 10.3 7.1
Trace Interface
TrcClk na na 10.3 7.1
TrcBS0:2 10.3 7.1
TrcES0:4 10.3 7.1
TrcTS0:5 (GPIO set) 10.3 7.1
TrcTS1:5 (EBC set) 15.3 10.2
TrcTS6 15.3 10.2
I/O Specifications—All Speeds (Sheet 7 of 7)
Notes:
1. Ethernet interface meets timing requirements as defined by IEEE 802.3 standard.
2. PCI-X timings are for asynchronous operation up to 133MHz. PCI-X input setup time requirement is 1.2ns for 133MHz and
1.7ns for 66MHz. PCI timings (in parentheses) are for asynchronous operation up to 66MHz. PCI output hold time
requirement is 1ns for 66MHz and 2ns for 33MHz.
3. The clock frequency for RMII operation is 50MHz ± 100ppm.
4. The clock frequency for SMII operation is 125MHz ± 100ppm.
5. These are DDR signals that can change on both the positive and negative clock transitions.
Signal
Input (ns) Output (ns) Output Current (mA)
Clock Notes
Setup Time
(TIS min)
Hold Time
(TIH min)
Valid Delay
(TOV max)
Hold Time
(TOH min)
I/O H
(minimum)
I/O L
(minimum)
440GX – Power PC 440GX Embedded Processor
78 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
I/O Specifications—500MHz–800MHz
Notes:
1. PerClk rising edge at package pin with a 10pF load trails the internal PLB clock by approximately 1.3ns.
Signal
Input (ns) Output (ns) Output Current (mA)
Clock Notes
Setup
Time
(TIS min)
Hold Time
(TIH min)
Valid Delay
(TOV max)
Hold Time
(TOH min)
I/O H
(minimum)
I/O L
(minimum)
External Slave Peripheral Interface
PerData00:31 2.8 1 6.6 0 15.3 10.2 PerClk
PerAddr00:31 2.9 1 6.6 0 15.3 10.2 PerClk
PerPar0:3 2.7 1 6.0 0 15.3 10.2 PerClk
PerWBE0:3 1.8 1 5.1 0 15.3 10.2 PerClk
PerCS0:7 na na 5.8 0 15.3 10.2 PerClk
PerOE na na 5.5 0 15.3 10.2 PerClk
PerWE na na 5.5 0 15.3 10.2
PerBLast 3.3 1 5.7 na 15.3 10.2 PerClk
PerReady[RcvrInh] 4.9 1 na na na na PerClk
PerR/W 2.5 1 5.7 na 15.3 10.2 PerClk
DMAReq0:3 dc dc na na na na PerClk
DMAAck0:3 na na 6.0 0 5.1 6.8 PerClk
EOT0:3/TC0:3 dc dc 6.3 0 15.3 10.2 PerClk
External Master Peripheral Interface
PerClk na na na na 15.3 10.2 PLB Clk 1
ExtReset na na 6.7 0 15.3 10.2 PerClk
HoldReq 2.8 1 na na na na PerClk
HoldAck na na 5.5 0 15.3 10.2 PerClk
ExtReq 1.5 1 na na na na PerClk
ExtAck na na 5.7 0 15.3 10.2 PerClk
BusReq na na 5.7 0 15.3 10.2 PerClk
PerErr 2.5 1 na na 15.3 10.2 PerClk
440GX – Power PC 440GX Embedded Processor
AMCC 79
Revision 1.19 – December 19, 2008
Data Sheet
DDR SDRAM I/O Specifications
The DDR SDRAM controller times its operation with internal PLB clock signals and generates MemClkOut0 from
the PLB clock. The PLB clock is an internal signal that cannot be directly observed. However MemClkOut0 is the
same frequency as the PLB clock signal and is in phase with the PLB clock signal.
Note: MemClkOut0 can be advanced with respect to the PLB clock by means of the SDRAM0_CLKTR program-
ming register. In a typical system, users advance MemClkOut by 90°. This depends on the specific applica-
tion and requires a thorough understanding of the memory system in general (refer to the DDR SDRAM
controller chapter in the PowerPC 440GX User’s Manual).
In the following sections, the label MemClkOut0(0) refers to MemClkOut0 when it has not been phase-shifted, and
MemClkOut0(90) refers to MemClkOut0 when it has been phase-advanced 90°. Advancing MemClkOut0 by 90°
creates a 3/4 cycle setup time and 1/4 cycle hold time for the address and control signals in relation to
MemClkOut0(90). The rising edge of MemClkOut0(90) aligns with the first rising edge of the DQS signal.
The following DDR data is generated by means of simulation and includes logic, driver, package RLC, and lengths.
Values are calculated over best case and worst case processes with speed, temperature, and voltage as follows:
Best Case = Fast process, -40°C, +1.6V
Worst Case = Slow process, +85°C, +1.4V
Note: In all the following DDR tables and timing diagrams, minimum values are measured under best case condi-
tions and maximum values are measured under worst case conditions.
The signals are terminated as indicated in the figure below for the DDR timing data in the following sections.
DDR SDRAM Simulation Signal Termination Model
10pF
10pF
MemClkOut0
MemClkOut0
120Ω
50Ω
Addr/Ctrl/Data/DQS
VTT = SVDD/2
PPC440GX
30pF
Note: This diagram illustrates the model of the DDR SDRAM interface used when generating simulation timing data.
It is not a recommended physical circuit design for this interface. An actual interface design will depend on many
factors, including the type of memory used and the board layout.
440GX – Power PC 440GX Embedded Processor
80 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
DDR SDRAM Output Driver Specifications
Signal Path
Output Current (mA)
I/O H (maximum) I/O L (minimum)
Write Data
MemData00:07 15.2 15.2
MemData08:15 15.2 15.2
MemData16:23 15.2 15.2
MemData24:31 15.2 15.2
MemData32:39 15.2 15.2
MemData40:47 15.2 15.2
MemData48:55 15.2 15.2
MemData56:63 15.2 15.2
ECC0:7 15.2 15.2
DM0:8 15.2 15.2
MemClkOut0 15.2 15.2
MemAddr00:12 15.2 15.2
BA0:1 15.2 15.2
RAS 15.2 15.2
CAS 15.2 15.2
WE 15.2 15.2
BankSel0:3 15.2 15.2
ClkEn0:3 15.2 15.2
DQS0:8 15.2 15.2
440GX – Power PC 440GX Embedded Processor
AMCC 81
Revision 1.19 – December 19, 2008
Data Sheet
DDR SDRAM Write Operation
The following diagram illustrates the relationship among the signals involved with a DDR write operation.
DDR SDRAM Write Cycle Timing
DQS
MemData
PLB Clk
MemClkOut0
MemClkOut0(90)
Addr/Cmd
TSK
TSA
THA
TDS
TDS
TSD
THD
TSD
THD
TSA = Setup time for address and command signals to MemClkOut0(90)
TSK = Delay from rising edge of MemClkOut0(0) to rising/falling edge of signal (skew)
THA = Hold time for address and command signals from MemClkOut0(90)
TDS = Delay from rising/falling edge of clock to the rising/falling edge of DQS
TSD = Setup time for data signals (minimum time data is valid before rising/falling edge of DSQ)
THD = Hold time for data signals (minimum time data is valid after rising/falling edge of DSQ)
440GX – Power PC 440GX Embedded Processor
82 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
I/O Timing—DDR SDRAM TDS
Notes:
1. All of the DQS signals are referenced to MemClkOut0(0).
2. The TDS values in the table include 3/4 of a cycle at the indicated clock speed.
3. To obtain adjusted values for lower clock frequencies, subtract 4.5 ns from the 166MHz values in the table and add 3/4 of the
cycle time for the lower clock frequency (TDS - 4.5 + 0.75TCYC).
Clock Speed (MHz) Signal Name
TDS (ns)
Minimum Maximum
166 DQS0 4.902 5.601
166 DQS1 4.872 5.535
166 DQS2 4.842 5.511
166 DQS3 4.855 5.546
166 DQS4 4.832 5.504
166 DQS5 4.867 5.525
166 DQS6 4.825 5.488
166 DQS7 4.880 5.543
166 DQS8 4.826 5.484
200 DQS0 3.660 4.295
200 DQS1 3.672 4.298
200 DQS2 3.664 4.293
200 DQS3 3.660 4.290
200 DQS4 3.671 4.294
200 DQS5 3.666 4.305
200 DQS6 3.666 4.296
200 DQS7 3.658 4.271
200 DQS8 3.662 4.291
440GX – Power PC 440GX Embedded Processor
AMCC 83
Revision 1.19 – December 19, 2008
Data Sheet
I/O Timing—DDR SDRAM TSK, TSA, and THA
Notes:
1. TSK is referenced to MemClkOut0(0). TSA and THA are referenced to MemClkOut0(90).
2. To obtain adjusted TSA values for lower clock frequencies, use 3/4 of the cycle time for the lower clock frequency and
subtract TSK maximum at 166MHz (0.75TCYC - TSKmax).
3. To obtain adjusted THA values for lower clock frequencies, use 1/4 of the cycle time for the lower clock frequency and add
TSK minimum at 166MHz (0.25TCYC + TSKmin).
Clock Speed (MHz) Signal Name
TSK (ns) TSA (ns) THA (ns)
Minimum Maximum Minimum Minimum
166 MemAddr00:12 0.184 0.592 3.908 1.684
166 BA0:1 0.439 0.683 3.817 1.939
166 BankSel0:3 0.249 0.779 3.721 1.749
166 ClkEn0:3 0.344 0.724 3.776 1.844
166 CAS 0.319 0.561 3.939 1.819
166 RAS 0.373 0.683 3.817 1.873
166 WE 0.393 0.639 3.816 1.893
200 MemAddr00:12 -0.283 0.307 3.443 0.967
200 BA0:1 -0.286 0.353 3.397 0.964
200 BankSel0:3 -0.270 0.321 3.429 0.980
200 ClkEn0:3 -0.280 0.298 3.452 0.970
200 CAS -0.270 0.294 3.456 0.980
200 RAS -0.263 0.311 3.439 0.987
200 WE -0.280 0.288 3.462 0.970
440GX – Power PC 440GX Embedded Processor
84 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
DDR SDRAM Read Operation
The following examples of timing for DDR SDRAM read operations are based on the relationship between the
incoming data and the PLB clock signal. Since the PLB clock cannot be directly observed, the delay of
MemClkOut(0) relative to the PLB clock (TMD) is provided.
The internal Read Clock signal, like MemClkOut0, is derived from the PLB clock and can be delayed relative to the
PLB clock by programming the RDCT and RDCD fields in the SDRAM0_TR1 register. The delay can be
programmed from 0 to 1/2 cycle in steps using RDCT. Setting RDCD results in a 1/2 cycle delay plus the value set
in RDCT. The delay of Read Clock relative to the PLB clock (TRD) shown below assumes the programmable Read
Clock delay is set to zero.
I/O Timing—DDR SDRAM TSD and THD
Notes:
1. TSD and THD are measured under worst case conditions.
2. The time values in the table include 1/4 of a cycle at the indicated clock speed.
3. To obtain adjusted TSD and THD values for lower clock frequencies, subtract 1.5 ns from the values at 166MHz in the table
and add 1/4 of the cycle time for the lower clock frequency (e.g., TSD - 1.5 + 0.25TCYC).
Clock Speed (MHz) Signal Names Reference Signal TSD (ns) THD (ns)
166 MemData00:07, DM0 DQS0 1.240 1.224
166 MemData08:15, DM1 DQS1 1.236 1.188
166 MemData16:23, DM2 DQS2 1.223 1.224
166 MemData24:31, DM3 DQS3 1.221 1.185
166 MemData32:39, DM4 DQS4 1.238 1.230
166 MemData40:47, DM5 DQS5 1.286 1.175
166 MemData48:55, DM6 DQS6 1.234 1.214
166 MemData56:63, DM7 DQS7 1.257 1.154
166 ECC0:7, DM8 DQS8 1.237 1.243
200 MemData00:07, DM0 DQS0 0.916 0.542
200 MemData08:15, DM1 DQS1 1.018 0.522
200 MemData16:23, DM2 DQS2 1.017 0.527
200 MemData24:31, DM3 DQS3 0.951 0.532
200 MemData32:39, DM4 DQS4 1.030 0.533
200 MemData40:47, DM5 DQS5 1.014 0.536
200 MemData48:55, DM6 DQS6 0.994 0.534
200 MemData56:63, DM7 DQS7 0.994 0.546
200 ECC0:7, DM8 DQS8 1.000 0.532
440GX – Power PC 440GX Embedded Processor
AMCC 85
Revision 1.19 – December 19, 2008
Data Sheet
DDR SDRAM MemClkOut0 and Read Clock Delay
In operation, following the receipt of an address and read command from the PPC440GX, the SDRAM generates
data and the DQS signals coincident with MemClkOut0. The data is latched into the PPC440GX using a DQS
signal that is delayed 1/4 of a cycle. In order to accommodate timing variations introduced by the system designs
using this chip, the three-stage data path shown below is used to eliminate metastability and allow data sampling to
be adjusted for minimum latency. This adjustment requires programming the Read Clock delay and the selection of
Stage 1, Stage 2, or Stage 3 data for sampling at RDSP.
DDR SDRAM Read Data Path
Read Clock
PLB Clk
MemClkOut0(0)
TMD
TRD
TMDmin =
TMDmax =
TRDmin =
TRDmax =
567ps
1705ps
183ps
-6ps
Stage 1 Stage 2 Stage 3
RDSP
PLB bus
FF, FF FF
FF
Data
Read Select
(SDRAM0_TR1)
DQS
1/4
Cycle
Delay
PLB Clock
Programmed
Delay
D
C
Package pins Mux
Read Clock
CC
C
DD
D
FF Timing:
TIS = Input setup time = 0.2ns
TIH = Input hold time = 0.1ns
TP = Propagation delay (D to Q or C to Q) =
XL
ECC
FF: Flip-Flop
XL: Transparent Latch
QQQ
Q
0.4ns maximum
440GX – Power PC 440GX Embedded Processor
86 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
In the following examples, the data strobes (DQS) and the data are shown to be coincident. There is actually a
slight skew as specified by the SDRAM specifications, and there can be additional skew due to loading and signal
routing. It is recommended that the signal length for all of the eight DQS signals be matched.
I/O Timing—DDR SDRAM TSIN and TDIN
Notes:
1. TSIN = Delay from DQS at package pin to C on Stage 1 FF.
2. TDIN = Delay from data at package pin to D on Stage 1 FF.
3. The time values for TSIN include 1/4 of a cycle at the indicated clock speed.
Clock Speed (MHz) Signal Name TSIN (ns)
minimum
TSIN (ns)
maximum Signal Name TDIN (ns)
minimum
TDIN (ns)
maximum
166 DQS0 2.132 2.884 MemData00:07 0.779 1.502
166 DQS1 2.132 2.867 MemData08:15 0.789 1.521
166 DQS2 2.127 2.873 MemData16:23 0.779 1.530
166 DQS3 2.116 2.851 MemData24:31 0.791 1.553
166 DQS4 2.100 2.845 MemData32:39 0.766 1.501
166 DQS5 2.103 2.844 MemData40:47 0.754 1.525
166 DQS6 2.144 2.902 MemData48:55 0.747 1.513
166 DQS7 2.110 2.864 MemData56:63 0.770 1.521
166 DQS8 2.122 2.860 ECC0:7 0.759 1.464
200 DQS0 1.942 2.365 MemData00:07 0.638 1.165
200 DQS1 1.920 2.314 MemData08:15 0.631 1.149
200 DQS2 1.938 2.361 MemData16:23 0.634 1.151
200 DQS3 1.945 2.370 MemData24:31 0.624 1.169
200 DQS4 1.932 2.332 MemData32:39 0.630 1.151
200 DQS5 1.936 2.348 MemData40:47 0.619 1.133
200 DQS6 1.938 2.356 MemData48:55 0.635 1.149
200 DQS7 1.943 2.360 MemData56:63 0.642 1.151
200 DQS8 1.952 2.381 ECC0:7 0.641 1.141
440GX – Power PC 440GX Embedded Processor
AMCC 87
Revision 1.19 – December 19, 2008
Data Sheet
Example 1:
If the data-to-PLB clock timing is as shown in the example below, then the read clock is not delayed and the Stage
1 data is sampled at (1). Except for small, low frequency memory systems with the memory located physically
close to the PPC440GX, it is unlikely that Stage 1 data can be sampled. When the data comes later, it is necessary
to sample Stage 2 or Stage 3 data. (see Examples 2 and 3). Another way to get the desired data-to-PLB timing to
allow Stage 1 sampling is to buffer MemClkOut0 and skew it enough to guarantee the timing. In this example
TT= 1.27ns at worst case conditions.
DDR SDRAM Read Cycle Timing—Example 1
DQS at pin
PLB Clock
TSIN
TDIN = Delay from data at package pin to D on Stage 1 FF.
TSIN = Delay from DQS at package pin to C on Stage 1 FF.
Data at pin D0 D1 D2 D3
DQS Stage 1 C
D0 D1 D2 D3
TDIN
D0 D2
Data in Stage 1 D
D1 D3
Data out Stage 1
High
Low
T
P
D0 D2
D1 D3
Data in at RDSP High
Low
with no ECC
T
T
TP = Propagation delay through FFs
TT = Propagation delay, Stage 1 input to RDSP input w/o ECC
D0 D2
D1 D3
Data out RDSP
High
Low
(1)
D2
D2
T
P
D0
D0
440GX – Power PC 440GX Embedded Processor
88 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Example 2:
In this example Read Clock is delayed almost 1/2 cycle. Without ECC, Stage 2 data can be sampled at (2). If ECC
is enabled, Stage 3 data must be sampled (see Example 3). In this example, TT = 1.27ns and TTE = 3.589ns at
worst case conditions.
DDR SDRAM Read Cycle Timing—Example 2
DQS at pin
PLB Clock
Read Clock Delayed
TSIN
Data at pin D0 D1 D2 D3
DQS Stage 1 C
D0 D1 D2 D3
TDIN
D0 D2
Data in Stage 1 D
D1 D3
Data out Stage 1
High
Low
T
P
D0 D2
D1 D3
Data in at RDSP High
Low
without ECC
TT = Propagation delay from Stage 2 input to RDSP input w/o ECC
D0 D2
D1 D3
Data out Stage 2
High
Low
Data out at RDSP High
Low
(2)
without ECC
T
P
D0 D2
D1 D3
Data in at RDSP High
Low
with ECC
D0 D2
D1 D3
TTE = Propagation delay from Stage 2 input to RDSP input with ECC
TT
TTE
D0 D2
440GX – Power PC 440GX Embedded Processor
AMCC 89
Revision 1.19 – December 19, 2008
Data Sheet
Example 3:
In this example, ECC is enabled. This requires that Stage 3 data be sampled at (3). If ECC is disabled, the system
will still work, but there will be more latency before the data is sampled into RDSP. Again, TT = 1.27ns and TTE =
3.589ns at worst case conditions.
DDR SDRAM Read Cycle Timing—Example 3
DQS at pin
PLB Clock
Read Clock Delayed
TSIN
Data at pin D0 D1 D2 D3
DQS Stage 1 C
D0 D1 D2 D3
TDIN
D0 D2
Data in Stage 1 D
D1 D3
Data out Stage 1
High
Low
T
P
D0 D2
D1 D3
Data out Stage 3 High
Low
with ECC
TT = Propagation delay from Stage 2 input to RDSP input w/o ECC
D0 D2
D1 D3
Data out Stage 2
High
Low
Data out RDSP High
Low
(3)
with ECC
T
P
D0 D2
D1 D3
Data in at RDSP High
Low
with ECC
D0 D2
D1 D3
TTE = Propagation delay from Stage 2 input to RDSP input with ECC
TTE
D0 D2
440GX – Power PC 440GX Embedded Processor
90 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Initialization
The PPC440GX provides the option for setting initial parameters based on default values or by reading them from
a slave PROM attached to the IIC0 bus (see “Serial EEPROM” below). Some of the default values can be altered
by strapping on external pins (see “Strapping” below).
Strapping
While the SysReset input pin is low (system reset), the state of certain I/O pins is read to enable certain default
initial conditions prior to PPC440GX start-up. The actual capture instant is the nearest SysClk edge before the
deassertion of reset. These pins must be strapped using external pull-up (logical 1) (recommended value is 3kΩ to
3.3V) or pull-down (logical 0) (recommended value is 1 kΩ to GND) resistors to select the desired default
conditions. They are used for strap functions only during reset. Following reset they are used for normal functions.
The following table lists the strapping pins along with their functions and strapping options:
Serial EEPROM
During reset, initial conditions other than those obtained from the strapping pins can be read from a ROM device
connected to the IIC0 port. At the de-assertion of SysReset, if the bootstrap controller is enabled, the PPC440GX
sequentially reads 16 bytes from the ROM device on the IIC0 port and sets the SDR0_SDSTP0, SDR0_SDSTP1,
SDR0_SDSTP2, and SDR0_SDSTP3 registers accordingly.
The initialization settings and their default values are covered in detail in the PowerPC 440GX Embedded
Processor User’s Manual.
Strapping Pin Assignments
Function Option
Ball Strapping
V24
(UART0_DCD)
V02
(UART0_DSR)
L07
(GMC1TxEr)
Serial device is disabled. Each of the four options (A–
D) is a combination of boot source, boot-source width,
and clock frequency specifications. Refer to the IIC
Bootstrap Controller chapter in the PPC440GX
Embedded Processor User’s Manual for details.
A 000
B0x1
C 010
D 100
Serial device is enabled. The option being
selected is the IIC0 slave address that will
respond with strapping data.
0x54 1 0 1
0x50 1 1 1
440GX – Power PC 440GX Embedded Processor
AMCC 91
Revision 1.19 – December 19, 2008
Data Sheet
Revision Log
Date Contents of Modification
08/07/2002 Add revision log.
08/30/2002 Change EMC0:1TxD0:1 and EMC0:1TxEn TOV from 15 to 11 ns.
09/25/2002 Update for L2 cache
10/22/2002 Add heat sink mounting information .
11/20/2002 Update I/O timing data.
01/07/2003 Update PCI-X I/O voltage specification.
Correct package drawing
01/22/2003 Correct description of SysReset signal.
Update for 533MHz parts and add power supply current values.
03/25/2003 Update DDR SDRAM timing.
Change RTBIxTX and RX control signals to data signals.
06/16/2003 Add 667MHz part numbers, update I/O specifications, and fill in missing data points.
07/15/2003 Update information concerning higher speed parts, bus clock ratios, the duplicate trace signals, and initialization
strapping pins. Update Ethernet signals with new and moved signals.
07/17/2003 Remove IBM Confidential.
12/02/2003 Revise DDR SDRAM I/O section.
01/13/2004 Correct TrcTS6 signal data (pin assignment and multiplexing).
02/12/2004 Restore VDD/OVDD voltage sequence restriction.
02/25/2004 Add three Revision C part numbers.
03/04/2004 Update part number list.
Update dimensions on package drawing.
03/25/2004 Correct GMCTxClk signal description from input-only to I/O.
05/12/2004 Add plastic package data, new power data, and update part number list.
05/20/2004 Upgrade 533MHz ceramic part to 105°C rating.
06/15/2004 Correct dimensions on ceramic package drawing.
06/30/2004 Replace misssing 533MHz C temperature range part.
11/01/2004
Add information on minimum SysClk and TRST duration during power-on reset.
Remove power sequence restrictions note from Absolute Maximum Rating table.
Restate power sequencing restrictions in Recommended DC Operating Conditions table.
Convert to AMCC format.
12/09/2004 Restore “Preliminary” to document classification.
06/16/2005 Add S (no L2 cache support) temperature range part numbers.
07/01/2005 Add reduced-lead ceramic and lead-free plastic part numbers.
10/17/2005 Clarify DDR SDRAM interface diagram.
11/07/2005 Remove metal-layer specification from technology description.
Add logo and number nomenclature to package drawing.
12/22/2005 Update I/O timing specs for EMC0:3TxD, GMC0RxD0:3, GMC1RxD0:3, GMCRxDV, GMC1RxCtl, GMCRxD0:7,
GMCRxEr, GMCCrS, GMCTxD0:7.
440GX – Power PC 440GX Embedded Processor
92 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
02/08/2006 Correct timing changes made in 12/22/05 version.
04/04/2006 Add six new PNs (two 533MHz and four 677MHz).
Remove two PNs (no Z shipping for 3NF533C or 3FF533C)
06/09/2006 Update clocking specs and EEPROM information.
09/11/2006 Add four posts to plastic package drawing.
Reduce maximum E temperature rating for selected plastic parts.
09/26/2006
Remove five PNs (end of life)
Add/change timing data (system and DDR SDRAM) for 800MHz Rev F parts
Increase minimum CPU frequency from 300MHz to 333MHz.
Increase SVDD for DDR SDRAM parts operating a 200MHz.
02/23/2007 Add two new ceramic 400MHz PNs. One is leaded (C) and the other is reduced-lead (R).
03/05/2007 Change TOH values for RGMII signals.
08/30/2007 Change the technical support telephone and fax number.
04/03/2008 Remove power supply power-up sequence requirements.
07/16/2008 Change package type to ceramic for PPC440GX-3RF400C (Doc Issue 549).
09/16/2008 Doc Issue 408. Rename AGND pins according to the analog voltage with which they are associated.
Doc Issue 483. Add two RGMII I/O timing waveforms.
09/22/2008 Doc Issue 595. Add pull-up and pull-down resistor values.
11/06/2008 Bugzilla Issue 4921. Increase OPB clock minimum frequency specification.
12/19/2008
Bugzilla Issue 5432. Modified the minimum and maximum values of the MemClkOut and PLB, OPB, and MAL in the
Clocking Specifications table on page 64.
Added notes 2 and 3.
Date Contents of Modification
440GX – Power PC 440GX Embedded Processor
AMCC 93
Revision 1.19 – December 19, 2008
Data Sheet
Printed in the United States of America, Thursday, January 08, 2009
The following are trademarks of AMCC in the United States, or other countries, or both:
Other company, product, and service names may be trademarks or service marks of others.
The information contained in this document is subject to change or withdrawal at any time without notice
and is being provided on an "AS IS" basis without warranty or indemnity of any kind, whether express or
implied, including without limitation, the implied warranties of non-infringement, merchantability, or fitness
for a particular purpose. Any products, services, or programs discussed in this document are sold or
licensed under AMCC's standard terms and conditions, copies of which may be obtained from your local
AMCC representative. Nothing in this document shall operate as an express or implied license or indemnity
under the intellectual property rights of AMCC or third parties.
Without limiting the generality of the foregoing, any performance data contained in this document was
determined in a specific or controlled environment and not submitted to any formal AMCC test. Therefore,
the results obtained in other operating environments may vary significantly. Under no circumstances will
AMCC be liable for any damages whatsoever arising out of or resulting from any use of the document or the
information contained herein.
AMCC
440GX – Power PC 440GX Embedded Processor
94 AMCC
Revision 1.19 – December 19, 2008
Data Sheet
Applied Micro Circuits Corporation
215 Moffett Park Drive, Sunnyvale, CA 94089
Phone: (408) 542-8600 — (800) 840-6055 — Fax: (408) 542-8601
http://www.amcc.com
AMCC reserves the right to make changes to its products, its data sheets, or related documentation, without notice and war-
rants its products solely pursuant to its terms and conditions of sale, only to substantially comply with the latest available data
sheet. Please consult AMCC’s Term and Conditions of Sale for its warranties and other terms, conditions and limitations.
AMCC may discontinue any semiconductor product or service without notice, and advises its customers to obtain the latest
version of relevant information to verify, before placing orders, that the information is current. AMCC does not assume any lia-
bility arising out of the application or use of any product or circuit described herein, neither does it convey any license under
its patent rights nor the rights of others. AMCC reserves the right to ship devices of higher grade in place of those of lower
grade.
AMCC SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED TO BE
SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL
APPLICATIONS.
AMCC is a registered Trademark of Applied Micro Circuits Corporation. Copyright © 2008 Applied Micro Circuits Corporation.