MAX-7 u-blox 7 GNSS modules Data Sheet Highlights: * Miniature LCC package * GNSS engine for GPS/QZSS, GLONASS * Low power consumption * Product variants to meet performance and cost requirements * Pin-to-pin and software compatible with MAX-6 family www.u-blox.com UBX-13004068 - R05 MAX-7 - Data Sheet Document Information Title MAX-7 Subtitle u-blox 7 GNSS modules Document type Data Sheet Document number UBX-13004068 Revision and date R05 Document status Production Information 11-Nov-2014 Document status information Objective Specification Document contains target values. Revised and supplementary data will be published later. Advance Information Document contains data based on early testing. Revised and supplementary data will be published later. Early Production Information Document contains data from product verification. Revised and supplementary data may be published later. Production Information Document contains the final product specification. This document applies to the following products: Product name Type number ROM/FLASH version PCN reference MAX-7C MAX-7Q MAX-7C-0-000 MAX-7Q-0-000 ROM1.00 ROM1.00 N/A N/A MAX-7W MAX-7W-0-000 ROM1.00 N/A u-blox reserves all rights to this document and the information contained herein. Products, names, logos and designs described herein may in whole or in part be subject to intellectual property rights. Reproduction, use, modification or disclosure to third parties of this document or any part thereof without the express permission of u-blox is strictly prohibited. The information contained herein is provided "as is" and u-blox assumes no liability for the use of the information. No warranty, either express or implied, is given, including but not limited, with respect to the accuracy, correctness, reliability and fitness for a particular purpose of the information. This document may be revised by u-blox at any time. For most recent documents, visit www.u-blox.com. Copyright (c) 2014, u-blox AG. u-blox(R) is a registered trademark of u-blox Holding AG in the EU and other countries. ARM(R) is the registered trademark of ARM Limited in the EU and other countries. UBX-13004068 - R05 Page 2 of 24 MAX-7 - Data Sheet Contents Contents.............................................................................................................................. 3 1 Functional description.................................................................................................. 5 1.1 Overview .............................................................................................................................................. 5 1.2 1.3 Product features ................................................................................................................................... 5 GNSS performance ............................................................................................................................... 6 1.3.1 GPS performance .......................................................................................................................... 6 1.3.2 GLONASS performance ................................................................................................................. 7 1.4 Block diagram....................................................................................................................................... 8 1.5 GNSS .................................................................................................................................................... 8 1.5.1 1.5.2 GPS ............................................................................................................................................... 8 GLONASS ...................................................................................................................................... 8 1.5.3 QZSS ............................................................................................................................................. 8 1.6 Augmented GNSS................................................................................................................................. 8 1.6.1 Assisted GNSS (A-GPS) .................................................................................................................. 9 AssistNow Online ......................................................................................................................................... 9 AssistNow Offline ........................................................................................................................................ 9 1.6.2 AssistNow Autonomous ................................................................................................................ 9 1.6.3 Satellite-Based Augmentation System (SBAS) ................................................................................. 9 1.7 EXTINT: External interrupt ..................................................................................................................... 9 1.7.1 Pin Control .................................................................................................................................... 9 1.7.2 1.8 1.9 TIMEPULSE ......................................................................................................................................... 10 Protocols and interfaces ...................................................................................................................... 10 1.10 Interfaces ........................................................................................................................................ 10 1.10.1 1.10.2 1.11 1.12 Oscillators.................................................................................................................................... 10 Real-Time Clock (RTC) ................................................................................................................. 11 Power management ........................................................................................................................ 11 1.12.1 1.12.2 1.13 DC/DC converter ......................................................................................................................... 11 Operating modes ........................................................................................................................ 11 Antenna .......................................................................................................................................... 12 1.13.1 1.13.2 Active antenna control (ANT_ON) ................................................................................................ 12 Antenna supervisor and short circuit detection ............................................................................ 12 Pin Definition .............................................................................................................. 13 2.1 3 UART ........................................................................................................................................... 10 Display Data Channel (DDC) ........................................................................................................ 10 Clock generation ............................................................................................................................ 10 1.11.1 1.11.2 2 Aiding ......................................................................................................................................... 10 Pin assignment ................................................................................................................................... 13 Configuration management ...................................................................................... 14 UBX-13004068 - R05 Production Information Contents Page 3 of 24 MAX-7 - Data Sheet 4 Electrical specification ................................................................................................ 14 4.1 Absolute maximum rating .................................................................................................................. 14 4.2 Operating conditions .......................................................................................................................... 15 4.3 Indicative current requirements ........................................................................................................... 16 5 Mechanical specifications .......................................................................................... 17 6 Reliability tests and approvals .................................................................................. 18 7 6.1 Reliability tests .................................................................................................................................... 18 6.2 Approvals ........................................................................................................................................... 18 Product handling & soldering .................................................................................... 18 7.1 Packaging ........................................................................................................................................... 18 7.1.1 Reels ........................................................................................................................................... 18 7.1.2 Tapes .......................................................................................................................................... 18 7.2 Shipment, storage and handling ......................................................................................................... 19 8 9 7.2.1 Moisture Sensitivity Levels ........................................................................................................... 19 7.2.2 7.2.3 Reflow soldering ......................................................................................................................... 19 ESD handling precautions ............................................................................................................ 20 Default messages ....................................................................................................... 21 Labeling and ordering information........................................................................... 22 9.1 Product labeling.................................................................................................................................. 22 9.2 Explanation of codes........................................................................................................................... 22 9.3 Ordering codes ................................................................................................................................... 22 Related documents........................................................................................................... 23 Revision history ................................................................................................................ 23 Contact .............................................................................................................................. 24 UBX-13004068 - R05 Production Information Contents Page 4 of 24 MAX-7 - Data Sheet 1 Functional description 1.1 Overview The MAX-7 series is the newest family of standalone GNSS modules from u-blox. With the exceptional performance of the u-blox 7 GNSS (GPS, GLONASS, QZSS and SBAS) engine, the MAX-7 series delivers high sensitivity and minimal acquisition times in the industry proven MAX form factor. The MAX-7 series provides maximum sensitivity while maintaining low system power. The MAX-7C is optimized for cost sensitive applications, the MAX-7Q provides best performance and lowest power consumption, while the MAX-7W provides best performance and is optimized for active antennas. The industry-proven MAX form factor allows easy migration from the previous MAX-6 generation. Sophisticated RF-architecture and interference suppression ensure maximum performance even in GNSS-hostile environments. The MAX-7 series combines a high level of integration capability with flexible connectivity options in a miniature package. This makes it perfectly suited for industrial applications with strict size and cost requirements. The 2 MAX-7Q is also halogen free (green) which makes it also perfectly suited for consumer applications. The I C compatible DDC interface provides connectivity and enables synergies with u-blox cellular modules. u-blox 7 modules use GNSS chips qualified according to AEC-Q100 and are manufactured in ISO/TS 16949 certified sites. Qualification tests are performed as stipulated in the ISO16750 standard: "Road vehicles - Environmental conditions and testing for electrical and electronic equipment". 1.2 Product features UBX-13004068 - R05 Production Information Functional description Page 5 of 24 MAX-7 - Data Sheet 1.3 GNSS performance 1.3.1 GPS performance Parameter Specification Receiver type 56 Channels u-blox 7 engine GPS/QZSS L1C/A SBAS: WAAS, EGNOS, MSAS Time-To-First-Fix 1 Cold Start MAX-7Q/W 29 s MAX-7C 30 s Warm Start Hot Start 28 s 1s 28 s 1s 5s 5s Aided Starts Sensitivity 2 3 Tracking & Navigation Reacquisition MAX-7Q/W MAX-7C -161 dBm -160 dBm -160 dBm -160 dBm Cold Start -148 dBm -147 dBm Warm Start Hot Start -148 dBm -156 dBm -148 dBm -155 dBm Autonomous SBAS 2.5 m 2.0 m RMS 99% Frequency of time pulse signal 30 ns 60 ns 0.25 Hz ... 10 MHz (configurable) Max navigation update rate Velocity accuracy 5 10 Hz 0.1 m/s Horizontal position accuracy 4 Accuracy of time pulse signal Heading accuracy5 Operational limits 6 0.5 degrees 4g 50,000 m 500 m/s Dynamics Altitude Velocity Table 1: GPS performance 1 All satellites at -130 dBm Dependent on aiding data connection speed and latency 3 Demonstrated with a good external LNA 4 CEP, 50%, 24 hours static, -130 dBm, > 6 SVs 5 50% @ 30 m/s 6 Assuming Airborne < 4 g platform 2 UBX-13004068 - R05 Production Information Functional description Page 6 of 24 MAX-7 - Data Sheet 1.3.2 GLONASS performance Parameter Specification Receiver type 56 Channels u-blox 7 engine GLONASS L1 FDMA 7 MAX-7Q/W MAX-7C Cold Start Warm Start Hot Start 30 s 25 s 1s 32 s 25 s 1s Tracking & Navigation MAX-7Q/W -158 dBm MAX-7C -158 dBm Reacquisition Cold Start -156 dBm -140 dBm -156 dBm -139 dBm Warm Start Hot Start -145 dBm -156 dBm -145 dBm -155 dBm RMS 99% Frequency of time pulse signal Max navigation update rate 50 ns 100 ns 0.25 Hz ... 10 MHz (configurable) 10 Hz Velocity accuracy 10 0.1 m/s Time-To-First-Fix Sensitivity 8 Horizontal position accuracy 9 Accuracy of time pulse signal Heading accuracy10 Operational limits 11 4.0 m 0.5 degrees 4g 50,000 m 500 m/s Dynamics Altitude Velocity Table 2: GLONASS performance 7 All satellites at -130 dBm Demonstrated with a good external LNA CEP, 50%, 24 hours static, -130 dBm, > 6 SVs 10 50% @ 30 m/s 11 Assuming Airborne < 4 g platform 8 9 UBX-13004068 - R05 Production Information Functional description Page 7 of 24 MAX-7 - Data Sheet 1.4 Block diagram Figure 1: MAX-7 block diagram 1.5 GNSS u-blox MAX-7 positioning modules are GNSS receivers and can singly receive and track GPS (including SBAS and QZSS) and GLONASS signals. QZSS and SBAS signals (by default) can be received concurrently with GPS signals. 1.5.1 GPS u-blox MAX-7 positioning modules are designed to receive and track the L1C/A signals provided at 1575.42 MHz by the Global Positioning System (GPS). 1.5.2 GLONASS The Russian GLONASS satellite system is an alternative system to the US-based Global Positioning System (GPS). The MAX-7 series modules are capable of receiving and processing GLONASS signals using the same hardware and provides the lowest power GLONASS functionality in the industry at low cost and with minimal integration effort. In order to take advantage of GPS and GLONASS, dedicated hardware preparation must be taken during the design-in phase, see the MAX-7 / NEO-7 Hardware Integration Manual [1] for u-blox design recommendations. The ability to receive and track GLONASS L1OF satellite signals with the same hardware results in an optimized hardware BOM and allows design of GLONASS ready receivers where required by regulations. GLONASS and GPS signals cannot be received and tracked simultaneously by u-blox MAX-7 modules. 1.5.3 QZSS The Quasi-Zenith Satellite System (QZSS) is a navigation satellite overlay system for the Pacific region covering Japan and Australia which transmits additional GPS L1C/A signals. u-blox MAX-7 positioning modules are able to receive and to track these signals simultaneously with GPS, resulting in better availability, especially under bad signal conditions e.g. in urban canyons. 1.6 Augmented GNSS For more details about augmented GNSS, see the u-blox 7 Receiver Description Including Protocol Specification [2]. UBX-13004068 - R05 Production Information Functional description Page 8 of 24 MAX-7 - Data Sheet 1.6.1 Assisted GNSS (A-GPS) A-GPS improves GNSS performance by delivering aiding data to the GNSS receiver via wireless networks or the Internet. Supplying information such as ephemeris, almanac, approximate last position, time and satellite status and an optional time synchronization signal significantly reduces Time to First Fix (TTFF) and improves acquisition sensitivity. AssistNow Online and AssistNow Offline are u-blox' end-to-end A-GPS services for devices with or without network connectivity. AssistNow Online and AssistNow Offline can either be used alone or in combination. They are very easy to implement, require no additional hardware, and generate virtually no CPU load. All MAX-7 series modules support u-blox' AssistNow Online, AssistNow Offline and AssistNow Autonomous A-GPS services, and are OMA SUPL compliant. AssistNow Online With AssistNow Online, an internet-connected GNSS device downloads assistance data from u-blox' AssistNow Online Service at system start-up. AssistNow Online is network operator independent and globally available. u-blox only sends ephemeris data for those satellites currently visible to the device requesting the data, thus minimizing the amount of data transferred. AssistNow Offline With AssistNow Offline, users download u-blox' Differential Almanac Correction Data from the Internet at their convenience. The correction data can be stored in the memory of the application processor. Therefore, the service requires no connectivity at system start-up and enables a position fix within seconds, even when no network is available. 1.6.2 AssistNow Autonomous AssistNow Autonomous provides functionality similar to Assisted GNSS without the need for a host or external network connection. It is an embedded feature available free-of-charge that accelerates GNSS positioning by capitalizing on the periodic nature of GPS satellite orbits. GPS orbit predictions are directly calculated by the GNSS receiver and no external aiding data or connectivity is required. AssistNow Autonomous can be used alone, or together with AssistNow Online or AssistNow Offline for increased positioning speed and accuracy. For more details see the u-blox 7 Receiver Description Including Protocol Specification [2]. 1.6.3 Satellite-Based Augmentation System (SBAS) u-blox MAX-7 positioning modules support SBAS. These systems supplement GPS data with additional regional or wide area GPS augmentation data. The system broadcasts augmentation data via satellite which can be used by GPS receivers to improve the resulting GPS precision. SBAS satellites can be used as additional satellites for ranging (navigation), further enhancing precision. The following SBAS are supported with MAX-7 modules: WAAS, EGNOS and MSAS. For more details see the u-blox 7 Receiver Description Including Protocol Specification [2] 1.7 EXTINT: External interrupt EXTINT is an external interrupt pin with fixed input voltage thresholds with respect to VCC_IO. It can be used for Control of the receiver or for Aiding. For more information about how to implement and configure these features see the u-blox 7 Receiver Description including Protocol Specification [2] and the MAX-7 / NEO-7 Hardware Integration Manual [1]. 1.7.1 Pin Control The pin control feature allows overriding the automatic active/inactive cycle of Power Save Mode. The state of the receiver can be controlled through the EXTINT pin. The receiver can also be turned off and sent into Backup Mode using EXTINT when Power Save Mode is not active. UBX-13004068 - R05 Production Information Functional description Page 9 of 24 MAX-7 - Data Sheet 1.7.2 Aiding The EXTINT pin can be used to supply time or frequency aiding data to the receiver. For time aiding the time can be supplied using hardware time synchronization where an accurate time pulse is connected to the EXTINT pin. Frequency aiding can be implemented by connecting a periodic rectangular signal with a frequency up to 500 kHz and arbitrary duty cycle (low/high phase duration must not be shorter than 50 ns) to the EXTINT pin, and providing the applied frequency value to the receiver using UBX messages. 1.8 TIMEPULSE A configurable time pulse signal is available with MAX-7 series modules. The TIMEPULSE output generates pulse trains synchronized with GPS or UTC time grid with intervals configurable over a wide frequency range. Thus it may be used as a low frequency time synchronization pulse or as a high frequency reference signal. By default the time pulse signal is configured to 1 pulse per second. For more information see the u-blox 7 Receiver Description including Protocol Specification [2]. 1.9 Protocols and interfaces Protocol Type NMEA UBX Input/output, ASCII, 0183, 2.3 (compatible to 3.0) Input/output, binary, u-blox proprietary RTCM Input, message 1, 2, 3, 9 Table 3: Available Protocols 2 All protocols are available on UART and DDC (I C compliant). For specification of the various protocols see the u-blox 7 Receiver Description Including Protocol Specification [2]. 1.10 Interfaces A number of interfaces are provided either for data communication or memory access. The embedded firmware uses these interfaces according to their respective protocol specifications. 1.10.1 UART MAX-7 modules include one UART interface, which can be used for communication to a host. It supports configurable baud rates. For supported baud rates see the u-blox 7 Receiver Description Including Protocol Specification [2]. 1.10.2 Display Data Channel (DDC) 2 An I C compliant DDC interface is available for communication with an external host CPU. The interface can be operated in slave mode only. The DDC protocol and electrical interface are fully compatible with the Fast-Mode 2 of the I C industry standard. Since the maximum SCL clock frequency is 400 kHz, the maximum transfer rate is 400 kb/s. 2 2 The DDC interface is I C Fast Mode compliant. For timing parameters consult the I C standard. The maximum bit rate is 400 kb/s. The interface stretches the clock when slowed down while serving interrupts, so real bit rates may be slightly lower. 1.11 Clock generation 1.11.1 Oscillators MAX-7 GNSS modules are available in Crystal and TCXO versions. The TCXO option allows accelerated weak signal acquisition, enabling faster start and reacquisition times. UBX-13004068 - R05 Production Information Functional description Page 10 of 24 MAX-7 - Data Sheet The careful selection and qualification of critical parts, such as GNSS oscillators, has resulted in u-blox modules being the most reliable positioning modules in the industry, particularly in challenging conditions. 1.11.2 Real-Time Clock (RTC) The RTC is driven by a 32 kHz oscillator, which makes use of a RTC crystal. If the main supply voltage fails and a battery is connected to V_BCKP, parts of the receiver switch off, but the RTC still runs providing a timing reference for the receiver. This operating mode is called Hardware Backup Mode, which enables all relevant data to be saved in the backup RAM to allow a hot or warm start later. With MAX-7C in Hardware Backup Mode the main oscillator is used as timing reference instead of the 32 kHz oscillator. MAX-7C apply single crystal mode, where the 26 MHz crystal oscillator can also be used to provide a frequency reference to the RTC without using an additional crystal for the RTC. This makes MAX-7C a more cost efficient solution at the expense of a higher backup current. For more information see the MAX-7 / NEO-7 Hardware Integration Manual [1] 1.12 Power management u-blox 7 technology offers a power optimized architecture with built-in autonomous power saving functions to minimize power consumption at any given time. Furthermore, the receiver can be used in two operating modes: Continuous mode for best performance or Power Save Mode for optimized power consumption respectively. In addition a high efficiency DC/DC converter is integrated to allow low power consumption even for higher main supply voltages. 1.12.1 DC/DC converter MAX-7Q and MAX-7C Modules integrate a DC/DC converter, providing a reduced power consumption by up to 50% especially when using a main supply voltage above 2.5 V. For more information see the MAX-7 / NEO-7 Hardware Integration Manual [1] 1.12.2 Operating modes MAX-7 series modules have two operating modes: * Continuous Mode for best GNSS performance * Power Save Mode to optimize power consumption 1.12.2.1 Continuous Mode Continuous Mode uses the acquisition engine at full performance resulting in the shortest possible TTFF and the highest sensitivity. It searches for all possible satellites until the almanac is completely downloaded. The receiver then switches to the tracking engine to lower power consumption. Thus, a lower tracking current consumption level will be achieved when: * A valid GNSS position is obtained * The entire almanac has been downloaded * The ephemeris for each satellite in view is valid 1.12.2.2 Power Save Mode For power sensitive applications u-blox MAX-7 receivers provide a Power Save Mode for reduced power consumption. Power Save Mode provides two dedicated methods called ON/OFF and Cyclic tracking, that reduce average current consumption in different ways to match the needs of the specific application. These options can be set by using a specific UBX message. For more information about power management strategies, see the u-blox 7 Receiver Description Including Protocol Specification [2]. UBX-13004068 - R05 Production Information Functional description Page 11 of 24 MAX-7 - Data Sheet Power Save Mode is not available in GLONASS mode. 1.13 Antenna 12 13 MAX-7 modules are designed for use with passive and active antennas. Parameter Specification Antenna Type Active Antenna Recommendations Passive and active antenna Minimum gain Maximum gain Maximum noise figure 15 dB (to compensate signal loss in RF cable) 50 dB 1.5 dB Table 4: Antenna Specifications for all MAX-7 modules 1.13.1 Active antenna control (ANT_ON) The ANT_ON Pin can be used to turn on and off an external LNA or an active antenna. This reduces power consumption in Power Save Mode or Backup mode. This pin is available only on MAX-7C and MAX-7Q. 1.13.2 Antenna supervisor and short circuit detection An antenna supervisor is available with MAX-7W. The antenna supervisor enables the receiver to detect short circuits at the active antenna and shut down the voltage bias immediately. A series resistor is needed in front of the V_ANT input to enable checking of the antenna bias voltage. UBX and NMEA messages are provided to report the condition of the antenna supply. Open circuit detection can also be supported with an additional external circuit. Antenna open circuit detection can be mapped to PIO13 and require external components For more information see the MAX-7 / NEO-7 Hardware Integration Manual [1] 12 13 For integration MAX-7 modules with cellular products, see the MAX-7 / NEO-7 Hardware Integration Manual [1]. For information on using active antennas with MAX-7 modules, see the MAX-7 / NEO-7 Hardware Integration Manual [1]. UBX-13004068 - R05 Production Information Functional description Page 12 of 24 MAX-7 - Data Sheet 2 Pin Definition 2.1 Pin assignment Figure 2: Pin Assignment Module Name PIO 14 Nr. 1 All GND - 2 All TxD 6 O 3 All RxD 7 I Serial Port 4 5 All All TIMEPULSE EXTINT 11 13 O I Time pulse (1PPS) External Interrupt Pin 6 7 All All V_BCKP VCC_IO - 8 9 All All VCC RESET_N - 10 All GND - 11 12 All All RF_IN GND - I GNSS signal input Ground 13 MAX-7C/Q MAX-7W ANT_ON Reserved 16 - O - Antenna control Reserved All MAX-7W VCC_RF V_ANT - No 14 15 I/O Description Ground Serial Port Backup voltage supply IO Supply Voltage I Supply voltage RESET_N Ground Output Voltage RF section Active Antenna Supply Voltage MAX-7C/Q Reserved - - Reserved 16 17 All All SDA SCL 9 8 I/O I/O DDC Data DDC Clock 18 All Reserved - - Reserved Table 5: Pinout Pins designated Reserved should not be used. For more information about Pinouts see the MAX-7 / NEO-7 Hardware Integration Manual [1]. 14 Peripheral Input Output UBX-13004068 - R05 Production Information Pin Definition Page 13 of 24 MAX-7 - Data Sheet 3 Configuration management Configuration settings can be modified with UBX configuration messages. The modified settings remain effective until power-down or reset. If these settings have been stored in battery-backup RAM, then the modified configuration will be retained, as long as the backup battery supply is not interrupted. For more information about configuration management, see the u-blox 7 Receiver Description Including Protocol Specification [2]. 4 Electrical specification The limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only, and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to these limits for extended periods may affect device reliability. Where application information is given, it is advisory only and does not form part of the specification. For more information see the MAX-7 / NEO-7 Hardware Integration Manual [1]. 4.1 Absolute maximum rating Parameter Symbol Module Min Max Units Power supply voltage VCC, VCC_IO All -0.5 3.6 V Backup battery voltage V_BCKP All -0.5 3.6 V Input pin voltage DC current trough any digital I/O pin (except supplies) VCC_RF output current Vin Ipin All -0.5 3.6 10 V mA ICC_RF All Input power at RF_IN Prfin All Antenna bias voltage Antenna bias current V_ANT I_ANT Storage temperature Tstg All Condition source impedance = 50 , continuous wave -40 100 mA 13 dBm 6 100 V mA 85 C Table 6: Absolute maximum ratings Stressing the device beyond the "Absolute Maximum Ratings" may cause permanent damage. These are stress ratings only. The product is not protected against overvoltage or reversed voltages. If necessary, voltage spikes exceeding the power supply voltage specification, given in table above, must be limited to values within the specified boundaries by using appropriate protection diodes. UBX-13004068 - R05 Production Information Configuration management Page 14 of 24 MAX-7 - Data Sheet 4.2 Operating conditions All specifications are at an ambient temperature of 25C. Extreme operating temperatures can significantly impact specification values. Applications operating near the temperature limits should be tested to ensure the specification. Parameter Symbol Module Min Typ Max Power supply voltage VCC, VCC_IO MAX-7C MAX-7Q/W 1.65 2.7 3.0 3.0 3.6 3.6 V V Backup battery voltage Backup battery current V_BCKP I_BCKP All MAX-7Q/W 1.4 3.6 15 V A MAX-7C 300 A V_BCKP = 3.0 V, VCC = 0 V (ESR dependent) MAX-7Q 20 A VCC_IO = VCC = 3.0 V (ESR dependent) MAX-7W 50 A VCC_IO= VCC = 3.0 V (ESR dependent) MAX-7C 305 A VCC_IO = VCC = 3.0 V (ESR dependent) SW backup current I_SWBCKP Input pin voltage range Digital IO Pin Low level input voltage Vin Vil All All 0 0 Digital IO Pin High level input voltage Vih All 0.7*VCC_IO Digital IO Pin Low level output voltage Digital IO Pin High level output voltage Vol Voh All All V_ANT antenna bias voltage Antenna bias voltage drop V_ANT V_ANT_DROP 2.7 VCC_RF voltage VCC_RF output current VCC_RF ICC_RF All All Receiver Chain Noise Figure Operating temperature NFtot Topr All All VCC_IO 0.2*VCC_IO Condition V_BCKP = 3.0 V, VCC = 0 V V V VCC_IO+0.5 V 0.4 V V Iol = 4 mA Ioh = 4 mA 5.5 V V IANT < -50 mA ICC_RF = 50 mA VCC_IO -0.4 0.1 VCC-0.1 50 3.5 -40 Units 85 V m A dB C Table 7: Operating conditions Operation beyond the specified operating conditions can affect device reliability. UBX-13004068 - R05 Production Information Electrical specification Page 15 of 24 MAX-7 - Data Sheet 4.3 Indicative current requirements Table 8 lists examples of the total system supply current for a possible application. Values in Table 8 are provided for customer information only as an example of typical power requirements. Values are characterized on samples, actual power requirements can vary depending on FW version used, external circuitry, number of SVs tracked, signal strength, type of start as well as time, duration and conditions of test. Parameter Max. supply current 15 Average supply current 16, 17 Symbol Module Iccp All Icc Acquisition 18 MAX-7C MAX-7W 21.0 39.5 mA mA MAX-7Q MAX-7C 22.0 16.5 mA mA MAX-7W MAX-7Q 29.5 17.5 mA mA MAX-7C 4.5 mA MAX-7W 7.0 mA MAX-7Q 5.0 mA Icc Tracking (Continuous mode,) Icc Tracking (Power Save mode / 1 Hz) Min Typ Max Units 67 mA Condition Estimated at 3V Estimated at 3V Estimated at 3V Table 8: Indicative power requirements at 3.0 V For more information about power requirements, see the MAX-7 / NEO-7 Hardware Integration Manual [1] 15 Use this figure to dimension maximum current capability of power supply. Measurement of this parameter with 1 Hz bandwidth. Use this figure to determine required battery capacity. 17 Simulated constellation of 8 satellites is used. All signals are at -130 dBm. VCC= 3 V 18 Average current from start-up until the first fix. 16 UBX-13004068 - R05 Production Information Electrical specification Page 16 of 24 MAX-7 - Data Sheet 5 Mechanical specifications Figure 3: Dimensions For information regarding the Paste Mask and Footprint see the MAX-7 / NEO-7 Hardware Integration Manual [1]. UBX-13004068 - R05 Production Information Mechanical specifications Page 17 of 24 MAX-7 - Data Sheet 6 Reliability tests and approvals 6.1 Reliability tests All MAX-7 modules are based on AEC-Q100 qualified GNSS chips. Tests for product family qualifications are according to ISO 16750 "Road vehicles - Environmental conditions and testing for electrical and electronic equipment", and appropriate standards. 6.2 Approvals Products marked with this lead-free symbol on the product label comply with the "Directive 2002/95/EC of the European Parliament and the Council on the Restriction of Use of certain Hazardous Substances in Electrical and Electronic Equipment" (RoHS). All u-blox 7 GNSS modules are RoHS compliant. 7 Product handling & soldering 7.1 Packaging MAX-7 modules are delivered as hermetically sealed, reeled tapes in order to enable efficient production, production lot set-up and tear-down. For more information see the u-blox Package Information Guide [3]. 7.1.1 Reels MAX-7 GNSS modules are deliverable in quantities of 500 pcs on a reel. MAX-7 modules are shipped on Reel Type B, as specified in the u-blox Package Information Guide [3]. 7.1.2 Tapes Figure 4 shows the position and orientation of MAX-7 modules as they are delivered on tape. The dimensions of the tapes are specified in Figure 5. Figure 4: Tape and module orientation UBX-13004068 - R05 Production Information Reliability tests and approvals Page 18 of 24 MAX-7 - Data Sheet Figure 5: MAX-7 Tape dimensions 7.2 Shipment, storage and handling For important information regarding shipment, storage and handling see the u-blox Package Information Guide [3]. 7.2.1 Moisture Sensitivity Levels The Moisture Sensitivity Level (MSL) relates to the packaging and handling precautions required. MAX-7 modules are rated at MSL level 4. For MSL standard see IPC/JEDEC J-STD-020, which can be downloaded from www.jedec.org. For more information regarding MSL see the u-blox Package Information Guide [3]. 7.2.2 Reflow soldering Reflow profiles are to be selected according u-blox recommendations (see the MAX-7 / NEO-7 Hardware Integration Manual [1]). UBX-13004068 - R05 Production Information Product handling & soldering Page 19 of 24 MAX-7 - Data Sheet 7.2.3 ESD handling precautions MAX-7 modules are Electrostatic Sensitive Devices (ESD). Observe precautions for handling! Failure to observe these precautions can result in severe damage to the GNSS receiver! GNSS receivers are Electrostatic Sensitive Devices (ESD) and require special precautions when handling. Particular care must be exercised when handling patch antennas, due to the risk of electrostatic charges. In addition to standard ESD safety practices, the following measures should be taken into account whenever handling the receiver: * Unless there is a galvanic coupling between the local GND (i.e. the work table) and the PCB GND, then the first point of contact when handling the PCB must always be between the local GND and PCB GND. * Before mounting an antenna patch, connect ground of the device * When handling the RF pin, do not come into contact with any charged capacitors and be careful when contacting materials that can develop charges (e.g. patch antenna ~10 pF, coax cable ~50-80 pF/m, soldering iron, ...) * To prevent electrostatic discharge through the RF input, do not touch any exposed antenna area. If there is any risk that such exposed antenna area is touched in non ESD protected work area, implement proper ESD protection measures in the design. * When soldering RF connectors and patch antennas to the receiver's RF pin, make sure to use an ESD safe soldering iron (tip). UBX-13004068 - R05 Production Information Product handling & soldering Page 20 of 24 MAX-7 - Data Sheet 8 Default messages Interface Settings UART Output 9600 Baud, 8 bits, no parity bit, 1 stop bit Configured to transmit both NMEA and UBX protocols, but only the following NMEA (and no UBX) messages have been activated at start-up: GGA, GLL, GSA, GSV, RMC, VTG, TXT 9600 Baud, 8 bits, no parity bit, 1 stop bit, Autobauding disabled Automatically accepts following protocols without need of explicit configuration: UBX, NMEA The GNSS receiver supports interleaved UBX and NMEA messages. Fully compatible with the I2C industry standard, available for communication with an external host CPU or u-blox cellular modules; operated in slave mode only. NMEA and UBX are enabled as input messages, only NMEA as output messages Maximum bit rate 400 kb/s. 1 pulse per second, synchronized at rising edge, pulse length 100 ms UART Input DDC TIMEPULSE (1Hz Nav) Table 9: Default messages Please refer to the u-blox 7 Receiver Description Including Protocol Specification [2] for information about further settings. UBX-13004068 - R05 Production Information Default messages Page 21 of 24 MAX-7 - Data Sheet 9 Labeling and ordering information 9.1 Product labeling The labeling of u-blox 7 GNSS modules includes important product information. The location of the MAX-7 series product type number is shown in Figure 6. Figure 6: Location of product type number on MAX-7 module label 9.2 Explanation of codes Three different product code formats are used. The Product Name is used in documentation such as this data sheet and identifies all u-blox 7 products, independent of packaging and quality grade. The Ordering Code includes options and quality, while the Type Number includes the hardware and firmware versions. Table 10 below details these three different formats: Format Structure Product Name Ordering Code PPP-GV PPP-GV-T Type Number PPP-GV-T-XXX Table 10: Product Code Formats The parts of the product code are explained in Table 11. Code Meaning Example PPP Product Family MAX G Product Generation 7 = u-blox 7 V T Variant Option / Quality Grade XXX Product Detail T = Timing, R = DR, etc. Describes standardized functional element or quality grade such as Flash size, automotive grade etc. Describes product details or options such as hard- and software revision, cable length, etc. Table 11: part identification code 9.3 Ordering codes Ordering No. Product MAX-7C-0 MAX-7Q-0 u-blox 7 GNSS Module, 1.65-3.6V, Crystal, ROM, 9.7x10.1 mm, 500 pcs/reel u-blox 7 GNSS Module, 2.7-3.6V, TCXO, ROM, 9.7x10.1 mm, 500 pcs/reel MAX-7W-0 u-blox 7 GNSS Module, 2.7-3.6V, TCXO, ROM, Active Antenna Supply, 9.7x10.1 mm, 500 pcs/reel Table 12: Product ordering codes for professional grade modules Product changes affecting form, fit or function are documented by u-blox. For a list of Product Change Notifications (PCNs) see our website. UBX-13004068 - R05 Production Information Labeling and ordering information Page 22 of 24 MAX-7 - Data Sheet Related documents [1] MAX-7 / NEO-7 Hardware Integration Manual, Docu. No. UBX-13003704 [2] [3] u-blox 7 Receiver Description including Protocol Specification, Docu. No GPS.G7-SW-12001 u-blox Package Information Guide, Docu. No. UBX-14001652 Revision history Revision Date Name Status / Comments - 14-Oct-2012 dhur R02 04-Oct-2013 cbib Initial release Last revision with document number GPS.G7-HW-12012 Advance Information status. Updated current values, removed USB, added VCC_IO R03 02-Apr-2014 julu R04 24-Jul-2014 julu Early Production Information. Terminology alignment for MAX-7 series GNSS module. Updated selector table in section 1.2; updated Figure 1 (removed not supported USB, SPI, SQI Flash from the Block Diagram); updated section 1.12.2 (RTC); added recommendation for using passive antenna (footnote in Table 4), added software backup current values in Table 7. Production Information. R05 11-Nov-2014 julu Updated section 1.2 (added product grade information to selector table) UBX-13004068 - R05 Production Information Related documents Page 23 of 24 MAX-7 - Data Sheet Contact For complete contact information visit us at www.u-blox.com u-blox Offices North, Central and South America u-blox America, Inc. Phone: E-mail: +1 703 483 3180 info_us@u-blox.com Regional Office West Coast: Phone: +1 408 573 3640 E-mail: info_us@u-blox.com Headquarters Europe, Middle East, Africa Asia, Australia, Pacific u-blox AG Phone: E-mail: Support: Phone: E-mail: Support: +41 44 722 74 44 info@u-blox.com support @u-blox.com Technical Support: Phone: E-mail: +1 703 483 3185 support_us@u-blox.com u-blox Singapore Pte. Ltd. +65 6734 3811 info_ap@u-blox.com support_ap@u-blox.com Regional Office Australia: Phone: +61 2 8448 2016 E-mail: info_anz@u-blox.com Support: support_ap@u-blox.com Regional Office China (Beijing): Phone: +86 10 68 133 545 E-mail: info_cn@u-blox.com Support: support_cn@u-blox.com Regional Office China (Shenzhen): Phone: +86 755 8627 1083 E-mail: info_cn@u-blox.com Support: support_cn@u-blox.com Regional Office India: Phone: +91 959 1302 450 E-mail: info_in@u-blox.com Support: support_in@u-blox.com Regional Office Japan: Phone: +81 3 5775 3850 E-mail: info_jp@u-blox.com Support: support_jp@u-blox.com Regional Office Korea: Phone: +82 2 542 0861 E-mail: info_kr@u-blox.com Support: support_kr@u-blox.com Regional Office Taiwan: Phone: +886 2 2657 1090 E-mail: info_tw@u-blox.com Support: support_tw@u-blox.com UBX-13004068 - R05 Production Information Contact Page 24 of 24