MITEQ AM SERIES AMPLIFIER FREQUENCY (MHz) 0.01-1000 MODEL NUMBER GAIN (dB) (Min.) VAR. (dB) (Max.) VSWR (Max.) IMPED. IN/OUT (Ohms) NOISE FIGURE (dB, Typ.) P1 dB (dBm) (Typ.) AM-1300 27 0.75 2.0:1 50/50 1.6 8 13 29 12 55 2 11 28 P1dB 27 26 10 9 8 7 24 6 0.3 100 200 300 400 500 600 700 800 900 1000 0 0 1 Frequency (MHz) 10 50 100 250 500 750 1000 Fre que ncy (MHz) Input & Output Return Loss (dBRL) Noise Figure (dB) 0 2.0 Noise Figure Output -5 -10 -15 -20 Input -25 1.8 1.6 1.4 1.2 1.0 -30 0.3 100 200 300 400 500 600 700 800 10 900 1000 50 100 250 500 750 1000 Frequency (MHz) Frequency (MHz) Reverse Isolation (dB) Low Frequency Gain Rolloff (dB) -30 1.0 -35 Gain Rolloff 0.0 -40 -45 -50 -1.0 -2.0 -3.0 -55 -4.0 -60 0.3 100 200 300 400 500 600 700 800 900 1000 4.0 9.0 50 100 200 300 Frequency (KHz) Frequency (MHz) ISO 9001:2000 Certified 20 * General Infomation * Warranty 100 Davids Drive, Hauppauge, NY 11788 TEL.: (631) 439-9220 * FAX: (631) 436-7430 e-mail: components@miteq.com * www.miteq.com AM-1300 051507 Gain (dB) 30 25 dB Return Loss 15 Output -1dB Gain Compression (+dBm) Gain (dB) Isolation NOM. DC POWER OUTLINE VOLTS (mA) NO. Gain (dB) 27.2 27.2 27.2 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.3 27.2 27.2 27.2 27.2 27.2 27.2 27.2 27.2 27.2 27.2 27.1 27.1 27.1 27.1 27.1 27.1 27.1 27.1 27.1 27.1 27.1 27.1 27.1 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 Freq. (MHz) 320 325 330 335 340 345 350 355 360 365 370 375 380 385 390 395 400 405 410 415 420 425 430 435 440 445 450 455 460 465 470 475 480 485 490 495 500 505 510 515 520 525 530 535 540 545 550 555 560 565 570 575 580 585 590 595 600 605 610 615 620 625 630 635 Gain (dB) 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.8 26.8 26.8 26.8 26.8 26.8 26.8 26.8 26.8 26.8 26.8 26.8 26.8 26.8 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 Freq. (MHz) 640 645 650 655 660 665 670 675 680 685 690 695 700 705 710 715 720 725 730 735 740 745 750 755 760 765 770 775 780 785 790 795 800 805 810 815 820 825 830 835 840 845 850 855 860 865 870 875 880 885 890 895 900 905 910 915 920 925 930 935 940 945 950 955 Gain (dB) 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 26.9 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.0 27.1 27.1 27.1 27.1 27.1 27.1 27.1 27.1 27.1 27.1 27.1 27.2 27.2 27.2 27.2 27.2 27.2 27.2 27.2 27.3 27.3 27.3 27.3 27.3 27.3 27.4 27.4 27.4 27.4 27.4 Freq. (MHz) 960 965 970 975 980 985 990 995 1000 Gain (dB) 27.4 27.4 27.5 27.5 27.5 27.5 27.5 27.5 27.5 100 Davids Drive, Hauppauge, NY 11788 TEL.: (631) 439-9220 * FAX: (631) 436-7430 e-mail: components@miteq.com * www.miteq.com AM-1300 051507 Freq. (MHz) 0.3 5.0 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240 245 250 255 260 265 270 275 280 285 290 295 300 305 310 315 MITEQ AM SERIES AMPLIFIER MITEQ AM SERIES AMPLIFIER Input VSWR (dBRL) -21 -30 -29 -29 -28 -27 -26 -25 -25 -24 -23 -23 -22 -21 -21 -20 -20 -20 -19 -19 -19 -18 -18 -18 -18 -17 -17 -17 -17 -17 -17 -17 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -16 -17 -17 -17 Output VSWR (dBRL) -16 -13 -13 -13 -13 -13 -13 -13 -13 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 Freq. (MHz) 315 320 325 330 335 340 345 350 355 360 365 370 375 380 385 390 395 400 405 410 415 420 425 430 435 440 445 450 455 460 465 470 475 480 485 490 495 500 505 510 515 520 525 530 535 540 545 550 555 560 565 570 575 580 585 590 595 600 605 610 615 620 625 Input VSWR (dBRL) -17 -17 -17 -17 -17 -17 -17 -18 -18 -18 -18 -18 -18 -18 -19 -19 -19 -19 -19 -20 -20 -20 -20 -21 -21 -21 -21 -22 -22 -22 -22 -23 -23 -23 -23 -24 -24 -24 -24 -25 -25 -25 -25 -25 -25 -25 -25 -25 -25 -25 -25 -25 -25 -25 -24 -24 -24 -24 -23 -23 -23 -23 -22 Output VSWR (dBRL) -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 Freq. (MHz) 630 635 640 645 650 655 660 665 670 675 680 685 690 695 700 705 710 715 720 725 730 735 740 745 750 755 760 765 770 775 780 785 790 795 800 805 810 815 820 825 830 835 840 845 850 855 860 865 870 875 880 885 890 895 900 905 910 915 920 925 930 935 940 Input VSWR (dBRL) -22 -22 -22 -21 -21 -21 -21 -20 -20 -20 -20 -19 -19 -19 -19 -18 -18 -18 -18 -18 -18 -17 -17 -17 -17 -17 -17 -16 -16 -16 -16 -16 -16 -16 -16 -15 -15 -15 -15 -15 -15 -15 -15 -15 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -14 -13 Output VSWR (dBRL) -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -11 -12 Freq. (MHz) 945 950 955 960 965 970 975 980 985 990 995 1000 Input VSWR (dBRL) -13 -13 -13 -13 -13 -13 -13 -13 -13 -13 -13 -13 Output VSWR (dBRL) -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -12 -13 100 Davids Drive, Hauppauge, NY 11788 TEL.: (631) 439-9220 * FAX: (631) 436-7430 e-mail: components@miteq.com * www.miteq.com AM-1300 051507 Freq. (MHz) 0.3 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240 245 250 255 260 265 270 275 280 285 290 295 300 305 310 MITEQ AM SERIES AMPLIFIER Reverse Isolation (dB) -46 -45 -45 -45 -44 -44 -44 -44 -44 -44 -44 -44 -44 -44 -44 -44 -44 -44 -44 -44 -43 -43 -43 -43 -43 -43 -43 -43 -43 -43 -43 -43 -43 -43 -43 -43 -43 -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -41 Freq. (MHz) 315 320 325 330 335 340 345 350 355 360 365 370 375 380 385 390 395 400 405 410 415 420 425 430 435 440 445 450 455 460 465 470 475 480 485 490 495 500 505 510 515 520 525 530 535 540 545 550 555 560 565 570 575 580 585 590 595 600 605 610 615 620 625 Reverse Isolation (dB) -42 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 Freq. (MHz) 630 635 640 645 650 655 660 665 670 675 680 685 690 695 700 705 710 715 720 725 730 735 740 745 750 755 760 765 770 775 780 785 790 795 800 805 810 815 820 825 830 835 840 845 850 855 860 865 870 875 880 885 890 895 900 905 910 915 920 925 930 935 940 Reverse Isolation (dB) -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -40 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -41 -42 Freq. (MHz) 945 950 955 960 965 970 975 980 985 990 995 1000 Reverse Isolation (dB) -42 -42 -42 -42 -42 -42 -42 -42 -42 -42 -43 -43 100 Davids Drive, Hauppauge, NY 11788 TEL.: (631) 439-9220 * FAX: (631) 436-7430 e-mail: components@miteq.com * www.miteq.com AM-1300 051507 Freq. (MHz) 0.3 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170 175 180 185 190 195 200 205 210 215 220 225 230 235 240 245 250 255 260 265 270 275 280 285 290 295 300 305 310 MITEQ AM SERIES AMPLIFIER OUTLINE 2 DIM A 1.92 [48.77] DIM B OUNCES 1.72 [43.69] 2.2 100 Davids Drive, Hauppauge, NY 11788 TEL.: (631) 439-9220 * FAX: (631) 436-7430 e-mail: components@miteq.com * www.miteq.com AM-1300 051507 NOTE: DIMENSIONS ARE IN INCHES [MILLIMETERS]. OPTIONS FOR BIPOLAR AMPLIFIERS INPUT BIAS TEE Add Suffix "-F" Used to inject bias signal to photo diode or other type of device. Check for availability on your model before ordering. Available on most units operating above 1 MHz. Please contact MITEQ with your custom requirements. after model number. Example: AU-2A-0150-1334/E will have existing +15 V pin enabled so that it can be used as a test point. Use caution with this option since any voltage applied here will also be present on both the RF output and input center pins. TYPE N OR BNC CONNECTORS Add Suffix "-N" or "-BNC" Type N-female and type BNC-female are available for all outlines 1 through 5, 12, 13 and 15 amplifiers. Add connector type after model number. Examples: AU-2A0150-N; AU-2A-0150-BNC. Type N-male and mixed connector types are also available on request. Please call MITEQ with your specific requirements. BIAS THROUGH THE OUTPUT CONNECTOR Add Suffix "-1306/E" or "-1306/D" INPUT INTERNAL LIMITER Add Suffix "-1103" Used to supply operating power when the amplifier is remotely located while eliminating the need to run a separate DC line. Specify whether existing power pin should be "Enabled" or "Disabled." To order, add -1306/E or -1306/D after model number. Example: AU-2A-0150-1306/E will have existing +15 V pin enabled so that it can be used as a test point. Use caution with this option since any voltage applied here will also be present on the RF output center pin. Available on most units operating above 1 MHz. Available on models up to 500 MHz. Will protect the input stage from CW signals as high as +30 dBm. To order, add "-1103" after model number. Example: AU-2A-0150-1103. Options are available for protection against short duration pulses up to 50 W. Used to supply operating power when the amplifier is remotely located and eliminates the need to run a separate DC line. This DC voltage is then internally fed to the RF input to power a remote LNA or other low power equipment. Maximum current of external load will vary with model type. Available on most units operating above 1 MHz. Please contact factory prior to ordering. RF OUTPUT RF INPUT Available as an add-on to most models using outlines 1 through 5 and 15. Includes 6-foot line cord with standard US line plug, internal fuse, on/off switch and LED indicator light. Amplifier is permanently mounted to power supply. To order, add "-1179" after model number. Example: AU-2A-0150-1179. Refer to outline 12 for dimensions. AC POWER SUPPLY (Wall plug-in unit) Part Number "205531-19" A low cost alternate to option "-1179", the wall plug-in unit is a small switching power supply capable of delivering 1 amp at 15 volts. AC POWER SUPPLY WITH SMC CONNECTORS (Wall plug-in unit) Part Number "-1179SC" Same as above except has mating SMC connectors on amplifier DC input and power supply DC output. Available for outlines 1 through 10, 13 and 15. ADDITIONAL OPTIONS AVAILABLE OPTION BIAS INPUT +V POWER SUPPLY Specify whether existing power pin should be "Enabled" or "Disabled". To order, add "-1334/E" or "-1334/D" Gain Window Phase Match Amplitude Match Gain Control SUFFIX -GW -PM -AM -GC 100 Davids Drive, Hauppauge, NY 11788 TEL.: (631) 439-9220 * FAX: (631) 436-7430 e-mail: components@miteq.com * www.miteq.com AM-1300 051507 BIAS THROUGH THE OUTPUT CONNECTOR WITH DC FEEDTHROUGH TO RF INPUT Add Suffix "-1334/E" or "-1334/D" AC POWER SUPPLY (100 to 240 VAC, 47 - 440 Hz). Add Suffix "-1179" GENERAL INFORMATION PRICING AND TERMS (R) MasterCard (R) A quotation on any item in the catalog is available by contacting the factory. All quotations, unless otherwise noted, are valid for 60 days from the date of issue, F.O.B. (FCA) Hauppauge, NY 11788. Pricing does not include customer or government source inspection unless otherwise noted. On international orders, an irrevocable letter of credit may be required. MITEQ accepts these credit cards: (R) Cards Welcome QUANTITY DISCOUNTS A quantity discount is generally available on most catalog items. Due to the wide variety of devices in the catalog, it is not possible to provide a standard discount schedule. When quantities are involved, please contact the factory and the appropriate information will be provided. SOURCE INSPECTION Government / customer source inspection is available on any item upon receipt of the complete written confirmation of purchase order items, including the prime government contract number. Source inspection with respect to some products increases the unit price and extends delivery because of duplicate standard final inspection and testing. It is recommended wherever possible that a Certificate of Compliance be substituted for source inspection to minimize price and delivery delays. SHIPPING INFORMATION Unless instructed otherwise by the customer, we will ship UPS in the U.S. F.O.B. (FCA) Hauppauge. Air freight will be used as the primary international means of shipment. Please indicate at time of purchase what method of shipment you require. RETURNED MATERIAL When returning material for repair or replacement, please ensure that there is complete information included with the shipment, giving a detailed description of the reason for its return, the date and purchase order on which it was obtained, and the exact address to which the material is to be reshipped. All returns must arrive freight, postage, duties and handling prepaid. REPAIR COSTS Warranty repairs will be made at no cost to the customer. Units out of warranty, or those which have been mishandled, will require approval by the customer for the charges involved before the repairs can be accomplished. We will provide an estimate for the cost of the repair, which can be applied to the repair, if approval is granted. For those items that are deemed beyond repair, or where the customer may decide not to repair the unit, an evaluation fee and handling charge will be applicable. APPLICATION ENGINEERING We maintain a large support staff of engineers who are experts in specific areas of microwave technology. Each has an engineering background that combines both a formal engineering education with training and experience in product design. As further technical support, we make available the services of our engineering and scientific staff, who may be consulted on more advanced circuit designs or application problems. DRAWINGS AND SPECIFICATIONS The material presented in this catalog was current at the time of publication. MITEQ Inc.'s continuing product improvement program makes it necessary to reserve the right to change our mechanical and electrical specifications without notice. If either of these parameters is critical, please contact the factory to verify that the information is current. ADDITIONAL INFORMATION ISO 9001:2000 Certified MITEQ FEDERAL SUPPLY CODE Our Federal Supply Code is: 33592 100 Davids Drive, Hauppauge, NY 11788 TEL.: (631) 439-9220 * FAX: (631) 436-7430 e-mail: components@miteq.com * www.miteq.com AM-1300 051507 WARRANTY