NOTES: THIS DRAWING AND THE SUBJECT MATTER SHOWN THEREON ARE CONFIDENTIAL AND THE PROPRIETARY PROPERTY OF STEWART CONNECTOR ("SCS") AND SHALL NOT BE STEWART REPRODUCED, COPIED OR USED IN ANY MANNER WITHOUT PRIOR WRITTEN CONSENT OF "SCS". THE SUBJECT MATTER CONNECTOR MAY BE PATENTED OR A PATENT MAY BE PENDING. SCS RD. 2, BOX 2020 GLEN ROCK) PENNSYLVANIA 17327 PART NUMBERS: SS-6446SAPG41-BA (30 MICROINCHES GOLD) SS6446SA-PG41-BA-50 (50 MICROINCHES GOLD) EMIRFI ONE PIECE SHIELDED, ESD GROUNDED, 4 X 6 JACK "-PG4" DESIGNATES ENHANCED SHIELD WITH ALL SIDE PANEL GROUNDS "1" DESIGNATES ALTERNATE SIDE SOLDER TAIL LOCATION "BA" DESIGNATES INCLUSION OF ALL TOP AND BOTTOM PANEL GROUNDS | * 545 [13.84] MAX -- eae ++ 850 [21.59] MAX. | * 608 [15.44 J a + 400 [10.16] L TOLERANCES COMPLY WITH F.C.C. DIMENSION REQUIREMENTS DIMENSIONS SHOWN WITH # TO BE CENTRAL ABOUT CENTER LINE DIMENSIONS SHOWN ARE SUBJECT TO CHANGE WITHOUT NOTICE. AVAILABLE WITH: -30 & 50 MICRO-INCH SELECTIVE GOLD PLATING -LOADED WITH 1- 6 CONTACTS CT640194A0 148 [3.75] HIGHEST POINT OF BEAM ns ia 425 [3.18}.010 [0.25] 1+ 599 [15.21] -|.014 [0.36] th o 083 [2.12] -] ml | | | 040 [1.02] HIGHEST POINT OF BEAM = }=-,425 [10.79] 050 [1.27] TYP TOL NON-ACCUM 025 [0.64] = ag 26 9.035 [0.89] (4) fF = Ww) N 128 [3.25] 125 [3.18] oN 9.062 [1.57] (2) #1 400 [10.16] * 530 [13.46] P.C.B. RECOMMENDED HOLE LAYOUT SEEN FROM COMPONENT SIDE TOLERANCE +.003 [0.08] UNLESS OTHERWISE SPECIFIED i L 120 bs SHT. 1 OF 21300 1200 1100 1000 900 800 700 600 500 400 300 200 100 GRAMS OF FORCE/GROUNDING BEAM STEWART CONNECTOR RD. 2, BOX 2020 GLEN ROCK, PENNSYLVANIA 17327 PART NUMBERS: SS-6446SAPG41-BA (30 MICROINCHES GOLD) SS-6446SAPG41BA-50 (50 MICROINCHES GOLD) - POINT OF CONTACT / =t ,080 .275 [6.99] MAX. a L No. mNY THE SUGGESTED PANEL OPENING IS INTENDED TO GIVE THE USER THE ABILITY TO HAVE REASONABLE JACK/PANEL CLEARANCES YET MAINTAIN RELIABLE GROUNDING CAPABILITY. THESE VARIABLES CAN BE ADJUSTED IN EITHER DIRECTION BUT MAY CARRY SOME 2 Q Ww Q 2 x CONSEQUENCES IN THE FORM OF LOWER MATING FORCES OR TIGHTER oe a ASSEMBLY TOLERANCES. FORCE VALUES ON THE GRAPH ARE GENERAL + + YW | | | | AVERAGES TAKEN AT THE POINT OF CONTACT SHOWN ABOVE. THE PANEL GROUNDING BEAM DEFLECTION SUGGESTED PANEL OPENING INCLUDES APPROXIMATELY .020 CLEAR- ANCE ON THE SIDES AND TOP AND .005 ON THE BOTTOM. S.0.S. = SUGGESTED OPENING SIZE t .555 4 CT640194A0 .000 (TOP OF PCB TO BOTTOM OF OPENING) .010 MAX. RADIUS (4) SUGGESTED PANEL OPENING SHT. 2 OF 2