SY69753L 3.3V, 125Mbps, 155Mbps Clock and Data Recovery Use lower-power SY69753AL for new designs General Description Features The SY69753L is a complete Clock Recovery and Data Retiming integrated circuit for OC-3/STS-3 applications at 155Mbps NRZ. The device is ideally suited for SONET/SDH/ATM applications and other high-speed data transmission systems. Clock recovery and data retiming is performed by synchronizing the on-chip VCO directly to the incoming data stream. The VCO center frequency is controlled by the reference clock frequency and the selected divide ratio. On-chip clock generation is performed through the use of a frequency multiplier PLL with a byte rate source as reference. The SY69753L also includes a link fault detection circuit. Datasheets and support documentation can be found on Micrel's web site at: www.micrel.com. * 3.3V power supply * SONET/SDH/ATM compatible * Clock and data recovery for 125Mbps/155Mbps NRZ data stream * Two on-chip PLLs: one for clock generation and another for clock recovery * Selectable reference frequencies * Differential PECL high-speed serial I/O * Line receiver input: no external buffering needed * Link fault indication * 100k ECL compatible I/O * Industrial temperature range (-40C to +85C) * Complies with Bellcore, ITU/CCITT and ANSI specifications for OC-3 applications * Available in 32-pin EPAD-TQFP Applications * Ethernet media converter(m) * SONET/SDH/ATM OC-3 * Proprietary architecture at 135Mbps to 180Mbps Micrel Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel +1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com December 2007 M9999-120307-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY69753L Ordering Information(1) Part Number Package Type Operating Range Package Marking Lead Finish H32-1 Industrial SY69753LHI Sn-Pb SY69753LHITR H32-1 Industrial SY69753LHI Sn-Pb (3) H32-1 Industrial SY69753LHG with Pb-Free bar-line indicator NiPdAu Pb-Free H32-1 Industrial SY69753LHG with Pb-Free bar-line indicator NiPdAu Pb-Free SY69753LHI (2) SY69753LHG SY69753LHGTR (2, 3) Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25C, DC Electricals only. 2. Tape and Reel. 3. Recommended for new designs. Pin Configuration 32-Pin EPAD-TQFP (H32-1) December 2007 2 M9999-120307-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY69753L Pin Description Inputs Pin Number Pin Name Type 2 3 RDINP RDINN Differential PECL Pin Name Serial Data Input: These built-in line receiver inputs are connected to the differential receive serial data stream. An internal receive PLL recovers the embedded clock (RCLK) and data (RDOUT) information. 5 REFCLK TTL Input Reference Clock: This input is used as the reference for the internal frequency synthesizer and the "training" frequency for the receiver PLL to keep it centered in the absence of data coming in on the RDIN inputs. 26 CD PECL Input Carrier Detect: This input controls the recovery function of the Receive PLL and can be driven by the carrier detect output of optical modules or from external transition detection circuitry. When this input is HIGH, the input data stream (RDIN) is recovered normally by the Receive PLL. When this input is LOW the data on the inputs RDIN will be internally forced to a constant LOW, the data outputs RDOUT will remain LOW, the Link Fault Indicator output LFIN forced LOW and the clock recovery PLL forced to look onto the clock frequency generated from REFCLK. 32 25 DIVSEL1 DIVSEL2 TTL Input Divider Select: These inputs select the ratio between the output clock frequency (RCLK/TCLK) and the REFCLK input frequency as shown in the "Reference Frequency Selection" table. 16 CLKSEL TTL Input Clock Select: This input is used to select either the recovered clock of the receiver PLL (CLKSEL = HIGH) or the clock of the frequency synthesizer (CLKSEL = LOW) to the TCLK outputs. Pin Number Pin Name Type 31 LFIN TTL Output Link Fault Indicator: This output indicates the status of the input data stream RDIN. Active HIGH signal is indicating when the internal clock recovery PLL has locked onto the incoming data stream. LFIN will go HIGH if CD is HIGH and RDIN is within the frequency range of the Receive PLL (1000ppm) and will be alternating if not. LFIN is an asynchronous output. 23 24 RDOUTN RDOUTP Differential PECL Receive Data Output: These ECL 100K outputs represent the recovered data from the input data stream (RDIN). This recovered data is specified against the rising edge of RCLK. 20 21 RCLKN RCLKP Differential PECL Clock Output: These ECL 100K outputs represent the recovered clock used to sample the recovered data (RDOUT). 18 17 TCLKP TCLKN Differential PECL Clock Output: These ECL 100K outputs represent either the recovered clock (CLKSEL = HIGH) used to sample the recovered data (RDOUT) or the transmit clock of the frequency synthesizer (CLKSEL = LOW). 9 10 PLLSP PLLSN Clock Synthesis PLL Loop Filter: External loop filter pins for the clock synthesis PLL. 14 15 PLLRN PLLRP Clock Recovery PLL Loop Filter: External loop filter pins for the receiver PLL. Outputs Pin Name Power and Ground Pin Number Pin Name 27, 28 VCC 29, 30 VCCA Analog Power Supply Voltage. 19, 22 VCCO Output Supply Voltage. 12, 13 GND 1, 4, 6, 7, 8 NC 11 GNDA Type Pin Name Power Supply. (1) (1) (1) Ground. No connect. Analog Ground. Note: 1. VCC, VCCA, VCCO must be the same value. December 2007 3 M9999-120307-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY69753L Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VCC) ......................................-0.5V to +5.0V Input Voltage (VIN) ..............................................-0.5V to VCC Output Current (IOUT) Continuous ...........................................................50mA Surge..................................................................100mA Lead Temperature (soldering, 20sec.) ..................... +260C Storage Temperature (Ts) .......................... -65C to +150C Input Voltage (VCC) .............................. +3.15V to +3.45V Ambient Temperature (TA) ..................... -40C to +85C Junction Temperature (TJ)....................................+125C (3) Package Thermal Resistance EPAD-TQFP (JA) Still-air....................................................... 28C/W 500lfpm..................................................... 20C/W EPAD-TQFP (JC) ............................................. 4C/W DC Electrical Characteristics TA = -40C to +85C, unless otherwise noted. Symbol Parameter VCC Power Supply Voltage ICC Power Supply Current Condition Min 3.15 Typ Max Units 3.3 3.45 V 170 230 mA PECL 100K DC Electrical Characteristics VCC = VCCO = VCCA = 3.3V 5%; TA = -40C to +85C, unless otherwise noted. Symbol Parameter Max Units VIH Input HIGH Voltage Condition VCC-1.165 Min Typ VCC-0.880 V VIL Input LOW Voltage VCC-1.810 VCC-1.475 V VOH Output HIGH Voltage 50 to VCC-2V VCC-1.075 VCC-0.830 V VOL Output LOW Voltage 50 to VCC-2V VCC-1.860 VCC-1.570 IIL Input LOW Current VIN = VIL (Min) 0.5 V A TTL DC Electrical Characteristics VCC = VCCO = VCCA = 3.3V 5%; TA = -40C to +85C, unless otherwise noted. Symbol Parameter VIH Input HIGH Voltage Condition Min VIL Input LOW Voltage VOH Output HIGH Voltage IOH = -0.4mA VOL Output LOW Voltage IOL = 4mA IIH Input HIGH Current VIN = 2.7V, VCC = Max. VIN = VCC, VCC = Max. -125 Typ 2.0 Max Units VCC V 0.8 V 2.0 IIL Input LOW Voltage VIN = 0.5V, VCC = Max. -300 IOS Output Short Circuit Current VOUT = 0V, (max., 1 sec.) -15 V 0.5 V +100 A A -100 mA A Notes: 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2. The data sheet limits are not guaranteed if the device is operated beyond the operating ratings. 3. Numbers valid with proper thermal design of PCB and exposed pad soldered to island on PCB. Refer to Figure on page 13. December 2007 4 M9999-120307-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY69753L AC Electrical Characteristics VCC = VCCO = VCCA = 3.3V 5%; TA = -40C to +85C, unless otherwise noted. Symbol Parameter Condition Min fVCO VCO Center Frequency fREFCLK x Byte Rate 800 Typ Max Units 1250 MHz fVCO VCO Center Frequency Tolerance Nominal tACQ Acquisition Lock Time 50 to VCC-2V tCPWH REFCLK Pulse Width HIGH 50 to VCC-2V 4 ns tCPWL REFCLK Pulse Width LOW VIN = VIL (Min) 4 ns tDV Data Valid 1/(2xfRCLK) -200 ps tDH Data Hold 1/(2xfRCLK) -200 ps tir REFCLK Input Rise Time tODC Output Duty Cycle (RCLK/TCLK) tRSKEW Recovered Clock Skew tr, tf ECL Output Rise/Fall Time (20% to 80%) 5 % 15 0.5 50 to VCC-2 s 2 ns 45 55 % of UI -200 +200 ps 100 400 ps Timing Waveforms December 2007 5 M9999-120307-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY69753L Functional Block The total loop dynamic of the clock recovery PLL provides jitter tolerance which is better than the specified tolerance in GR-253-CORE. Lock Detect The SY69753L contains a link fault indication circuit, which monitors the integrity of the serial data inputs. If the received serial data fails the frequency test, then the PLL will be forced to lock to the local reference clock. This will maintain the correct frequency of the recovered clock output under loss of signal or loss of lock conditions. If the recovered clock frequency deviates from the local reference clock frequency by more than approximately 1000ppm, the PLL will be declared out of lock. The lock detect circuit will poll the input data stream in an attempt to reacquire lock to data. If the recovered clock frequency is determined to be within approximately 1000ppm, the PLL will be declared in lock and the lock detect output will go active. Performance The SY69753L PLL complies with the jitter specifications proposed for SONET/SDH equipment defined by the Bellcore Specifications: GR-253CORE, Issue 2, December 1995 and ITU-T Recommendations: G.958 document, when used with differential inputs and outputs. Functional Description Clock Recovery Clock Recovery, as shown in the block diagram, generates a clock that is at the same frequency as the incoming data bit rate at the Serial Data input. The clock is phase aligned by a PLL so that it samples the data in the center of the data eye pattern. The phase relationship between the edge transitions of the data and those of the generated clock are compared by a phase/frequency detector. Output pulses from the detector indicate the required direction of phase correction. These pulses are smoothed by an integral loop filter. The output of the loop filter controls the frequency of the Voltage Controlled Oscillator (VCO), which generates the recovered clock. Frequency stability, without incoming data, is guaranteed by an alternate reference input (REFCLK) that the PLL locks onto when data is lost. If the Frequency of the incoming signal varies by greater than approximately 1000ppm with respect to the synthesizer frequency, the PLL will be declared out of lock, and the PLL will lock to the reference clock. The loop filter transfer function is optimized to enable the PLL to track the jitter, yet tolerate the minimum transition density expected in a received SONET data signal. This transfer function yields a 30s data stream of continuous 1's or 0's for random incoming NRZ data. December 2007 6 M9999-120307-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY69753L Input Jitter Tolerance Jitter Transfer Input jitter tolerance is defined as the peak-to-peak amplitude of sinusoidal jitter applied on the input signal that causes an equivalent 1dB optical/electrical power penalty. SONET input jitter tolerance requirement condition is the input jitter amplitude that causes an equivalent of 1dB power penalty. Jitter transfer function is defined as the ratio of jitter on the output OC-N/STS-N signal to the jitter applied on the input OC-N/STS-N signal versus frequency. Jitter transfer requirements are shown in Figure 2. Jitter Generation The jitter of the serial clock and serial data outputs shall not exceed .01 U.I. rms when a serial data input with no jitter is presented to the serial data inputs. OC/STS-N Level f0 (Hz) f1 (Hz) f2 (Hz) f3 (Hz) ft (Hz) OC/STS-N Level fc (kHz) P (dB) 3 10 30 300 6.5 65 3 130 0.1 Figure 1. Input Jitter Tolerance December 2007 Figure 2. Jitter Transfer 7 M9999-120307-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY69753L Loop Filter Components(1) R1 = 350 C1 = 1.5F (X7R Dielectric) R2 = 680 C2 = 1.0F (X7R Dielectric) Note: 1. Suggested values. Values may vary for different applications. Reference Frequency Selection DIVSEL1 DIVSEL2 fRCLK/fREFCLK 0 0 8 0 1 10 1 0 16 1 1 20 December 2007 8 M9999-120307-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY69753L Application Example Note: C3, C4 are optional. C1 = 1.5F C2 = 1.0F R1 = 350 R2 = 680 R3 through R10 = 5k R12 = 12k R13 = 130 December 2007 9 M9999-120307-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY69753L Bill of Materials Item Part Number Manufacturer Description Qty. C1 ECU-V1H104KBW Panasonic (1) C2 ECU-V1H104KBW Panasonic (1) 1.0F Ceramic Capacitor, Size 1206, X7R Dielectric, Loop Filter, Critical 1 C3, C4 ECU-V1H104KBW Panasonic (1) 0.47F Ceramic Capacitor, Size 1206, X7R Dielectric, Loop Filter, Optional 2 C5 ECS-T1ED226R Panasonic (1) 22F Tantalum Electrolytic Capacitor, Size D 1 C6 ECU-V1H104KBW Panasonic (1) 0.1F Ceramic Capacitor, Size 1206, X7R Dielectric Power Supply Decoupling 1 C7, C8, C9, C10 ECS-T1EC685R Panasonic (1) 6.8F Tantalum Electrolytic Capacitor, Size C 4 C19 ECJ-3YB1E105K Panasonic (1) 0.1F Ceramic Capacitor, Size 1206, X7R Dielectric VEEA Decoupling 1 C11, C13 ECU-V1H104KBW Panasonic (1) 0.1F Ceramic Capacitor, Size 1206, X7R Dielectric VCCO/VCC Decoupling 1 C15, C17 ECU-V1H104KBW Panasonic (1) 0.1F Ceramic Capacitor, Size 1206, X7R Dielectric VCCA/VEEA Decoupling 1 C20 ECU-V1H104KBW Panasonic (1) 0.1F Ceramic Capacitor, Size 1206, X7R Dielectric VEEA Decoupling 1 C12, C14 ECU-V1H103KBW Panasonic (1) 0.01F Ceramic Capacitor, Size 1206, X7R Dielectric VCCO/VCC Decoupling 1 C16, C18 ECU-V1H103KBW Panasonic (1) 0.01F Ceramic Capacitor, Size 1206, X7R Dielectric VCCA/VEEA Decoupling 1 C21 ECU-V1H103KBW Panasonic (1) 0.01F Ceramic Capacitor, Size 1206, X7R Dielectric VEEA Decoupling 1 D1 1N4148 Diode 1 D2 P300-ND/P301-ND Panasonic (1) T-1 3/4, Red LED 1 J1, J2, J3, J4, J5, J6, J7, J8, J9, J10, J11, J12 142-0701-851 Gold Plated, Jack, SMA, PCB Mount 12 L1, L2, L3 BLM21A102F Ferrite Beads, Power Noise Suppression 3 Q1 NTE123A Johnson (2) Components (3) Murata (4) NTE 1.5F Ceramic Capacitor, Size 1206, X7R Dielectric, Loop Filter, Critical 1 2N2222A Buffer/Driver Transistor, NPN 1 R1 350 Resistor, 2%, Size 1206, Loop Filter Component, Critical 1 R2 680 Resistor, 2%, Size 1206, Loop Filter Component, Critical 1 R3, R4, R5, R6, R7, R8, R9, R10 5k Pull-up Resistor, 2%, Size 1206 8 R11 1k Pull-down Resistor, 2%, Size 1206 1 R12 12k Resistor, 2%, Size 1206 1 130 Pull-up Resistor, 2%, Size 1206 1 SPST, Gold Finish, Sealed Dip Switch 1 R13 SW1 206-7 (5) CTS Notes: 1. Panasonic: www.panasonic.com. 2. Johnson Components: www.johnson-components.com. 3. Murata: www.murata.com. 4. NTE: www.nte.com. 5. CTS: www.cts.com. December 2007 10 M9999-120307-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. Appendix A SY69753L 6. Maintain low jitter on the REFCLK input. Isolate the XTAL oscillator from power supply noise by adequately decoupling. Keep XTAL oscillator close to device, and minimize capacitive coupling from adjacent signals. 7. Higher speed operation may require use of fundamental-tone (third-overtone typically has more jitter) crystal-based oscillator for optimum performance. Evaluate and compare candidates by measuring TXCLK jitter. 8. All unused outputs require termination. To conserve power, unused PECL outputs can be terminated with a 1k resistor to VEE. Layout and General Suggestions 1. Establish controlled impedance stripline, microstrip, or coplanar construction techniques. 2. Signal paths should have approximately the same width as the device pads. 3. All differential paths are critical timing paths, where skew should be matched to within 10ps. 4. Signal trace impedance should not vary more than 5%. If in doubt, perform TDR analysis of all high-speed signal traces. 5. Maintain compact filter networks as close to filter pins as possible. Provide ground plane relief under filter path to reduce stray capacitance. Be careful of crosstalk coupling into the filter network. December 2007 11 M9999-120307-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY69753L Package Information 32-Pin EPAD-TQFP (H32-1) December 2007 12 M9999-120307-F hbwhelp@micrel.com or (408) 955-1690 Micrel, Inc. SY69753L PCB Thermal Consideration for 32-Pin EPAD-TQFP Package MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2005 Micrel, Incorporated. December 2007 13 M9999-120307-F hbwhelp@micrel.com or (408) 955-1690