MM5452, MM5453 www.ti.com SNLS367C - FEBRUARY 1995 - REVISED MARCH 2013 MM5452/MM5453 Liquid Crystal Display Drivers Check for Samples: MM5452, MM5453 FEATURES DESCRIPTION * * * * * * * * The MM5452 is a monolithic integrated circuit utilizing CMOS metal gate, low threshold enhancement mode devices. It is available in a 40-pin PDIP package. The chip can drive up to 32 segments of LCD and can be paralleled to increase this number. The chip is capable of driving a 41/2-digit 7-segment display with minimal interface between the display and the data source. 1 2 Serial Data Input No Load Signal Required DATA ENABLE (MM5452) Wide Power Supply Operation TTL Compatibility 32 or 33 Outputs Alphanumeric and Bar Graph Capability Cascaded Operation Capability The MM5452 stores display data in latches after it is clocked in, and holds the data until new display data is received. APPLICATIONS * * * * * COPSTM or Microprocessor Displays Industrial Control Indicator Digital Clock, Thermometer, Counter, Voltmeter Instrumentation Readouts Remote Displays Block Diagram Figure 1. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1995-2013, Texas Instruments Incorporated MM5452, MM5453 SNLS367C - FEBRUARY 1995 - REVISED MARCH 2013 Absolute Maximum Ratings www.ti.com (1) (2) Voltage at Any Pin, Referenced to Gnd -0.3V to +10V Storage Temperature -65C to +150C Power Dissipation at 25C 350mW Power Dissipation at 70C 300mW Junction Temperature +150C Lead Temperature (1) (2) (Soldering, 10s) 300C "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be ensured. They are not meant to imply that the devices should be operated at these limits. The table of "Electrical Characteristics" specifies conditions of device operation. If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications. Recommended Operating Conditions VDD 3V to 10V Operating Temperature -40C to 85C Electrical Characteristics TA within operating range, VDD = 3.0V to 10V, VSS = 0V unless otherwise specified. Parameter Conditions Max Units 10 V VDD= 5V 10 A VDD= 10V 40 A VDD= 3V 0.4 V VDD= 5V 0.8 V VDD= 10V 0.8 V Supply Voltage, VDD Min Typ 3 Average Supply Current, IDD All Outputs Open, Clock=Gnd, Data=Gnd,OSC=Gnd, BP_IN @ 32Hz Input Logical '0' Voltage, VIL Input Logical '1' Voltage, VIH VDD= 3V 2.0 V VDD= 5V 2.0 V VDD= 10V 8.0 Segment Sink Current, IOL VDD= 3V, VOUT= 0.3V -20 Segment Source Current, IOH VDD= 3V, VOUT= 2.7V Backplane Out Sink Current, IOL VDD= 3V, VOUT= 0.3V Backplane Out Source Current, IOH VDD= 3V, VOUT= 2.7V 320 Segment Output Offset Voltage Segment Load = 250pF Clock Input Frequency, fCLOCK A 20 40 A -320 -500 A 500 A (1) Backplane Output Offset Voltage Backplane Load = 8750pF Backplane Out Frequency (1) ROSC_IN= 50k, COSC_IN= 0.01F (2) V -40 +/-50 mV +/-50 mV 75 Hz VDD= 3V (1) (3) 500 VDD= 5V (1) 750 kHz 1.0 MHz 60 % VDD= 10V (1) kHz Clock Input Duty Cycle (2) 40 Data Input Set-Up Time, tDS 300 ns Data Input Hold Time, tDH 300 ns DataEnable Set-up Time, tDES 100 ns (1) (2) (3) 2 This parameter is ensured (but not production tested) over the operating temperature range and the operating supply voltage range. Not to be used in Q.A. testing. Clock input rise time (tr) and fall time (tf) must not exceed 300ns AC input waveform for test purposes: tr 20ns, tf 20ns, fCLOCK= 500kHz, Duty Cycle = 50% 10% Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: MM5452 MM5453 MM5452, MM5453 www.ti.com SNLS367C - FEBRUARY 1995 - REVISED MARCH 2013 Connection Diagram Figure 2. Top View See Package Number NFJ0040A Figure 3. Top View See Package Number NFJ0040A Figure 4. Top View See Package Number FN0044A Figure 5. Top View See Package Number FN0044A Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: MM5452 MM5453 3 MM5452, MM5453 SNLS367C - FEBRUARY 1995 - REVISED MARCH 2013 www.ti.com FUNCTIONAL DESCRIPTION The MM5452 is specifically designed to operate 41/2-digit 7-segment displays with minimal interface with the display and the data source. Serial data transfer from the data source to the display driver is accomplished with 2 signals, serial data and clock. Since the MM5452 does not contain a character generator, the formatting of the segment information must be done prior to inputting the data to the MM5452. Using a format of a leading "1" followed by the 32 data bits allows data transfer without an additional load signal. The 32 data bits are latched after the 36th clock is complete, thus providing non-multiplexed, direct drive to the display. Outputs change only if the serial data bits differ from the previous time. A block diagram is shown in Figure 1. For the MM5452 a DATA ENABLE is used instead of the 33rd output. If the DATA ENABLE signal is not required, the 33rd output can be brought out. This is the MM5453 device. Figure 7 shows the input data format. A start bit of logical "1" precedes the 32 bits of data. At the 36th clock a LOAD signal is generated synchronously with the high state of the clock, which loads the 32 bits of the shift registers into the latches. At the low state of the clock a RESET signal is generated which clears all the shift registers for the next set of data. The shift registers are static master-slave configuration. There is no clear for the master portion of the first shift register, thus allowing continuous operation. If the clock is not continuous, there must be at least a complete set of 36 clocks otherwise the shift registers will not load and clear. Bit 1 is the first bit following the start bit and it will appear on device pin 18 of the MM5452N and MM5453N, and on device pin 20 of the MM5452V and MM5453V. Figure 6 shows the timing relationships between data, clock and DATA ENABLE. Figure 6. Timing Diagram Figure 7. Input Data Format Figure 8 shows a typical application. Note how the input data maps to the output pins and the display. The MM5452 and MM5453 do not have format restrictions, as all outputs are controllable. The application assumes a specific display pinout. Different display/driver connection patterns will, of course, yield a different input data format. 4 Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: MM5452 MM5453 MM5452, MM5453 www.ti.com SNLS367C - FEBRUARY 1995 - REVISED MARCH 2013 Consult LCD manufacturer's data sheet for specific pinouts. Figure 8. Typical 41/2-Digit Display Application Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: MM5452 MM5453 5 MM5452, MM5453 SNLS367C - FEBRUARY 1995 - REVISED MARCH 2013 www.ti.com *The minimum recommended value for R for the oscillator input is 9 k. An RC time constant of approximately 4.91 x 10-4 should produce a backplane frequency between 30 Hz and 150 Hz. Figure 9. Parallel Backplane Outputs Figure 10. External Backplane Clock Figure 11 shows a four wire remote display that takes advantage of the device's serial input to move many bits of display information on a few wires. USING AN EXTERNAL CLOCK The MM5452/MM5453 LCD Drivers can be used with an externally supplied clock, provided it has a duty cycle of 50%. Deviations from a 50% duty cycle result in an offset voltage on the LCD. In Figure 10, a flip-flop is used to assure a 50% duty cycle. The oscillator input is grounded to prevent oscillation and reduce current consumptions in the chips. The oscillator is not used. Using an external clock allows synchronizing the display drive with AC power, internal clocks, or DVM integration time to reduce interference from the display. Figure 12 is a general block diagram that shows how the device's serial input can be used to advantage in an analog display. The analog voltage input is compared with a staircase voltage generated by a counter and a digital-to-analog converter or resistor array. The result of this comparison is clocked into the MM5452, MM5453. The next clock pulse increments the staircase and clocks the new data in. 6 Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: MM5452 MM5453 MM5452, MM5453 www.ti.com SNLS367C - FEBRUARY 1995 - REVISED MARCH 2013 With a buffer amplifier, the same staircase waveform can be used for many displays. The digital-to-analog converter need not be linear; logarithmic or other non-linear functions can be displayed by using weighted resistors or special DACs. This system can be used for status indicators, spectrum analyzers, audio level and power meters, tuning indicators, and other applications. Figure 11. Four Wire Remote Display Data is high until staircase > input Figure 12. Analog Display Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: MM5452 MM5453 7 MM5452, MM5453 SNLS367C - FEBRUARY 1995 - REVISED MARCH 2013 www.ti.com REVISION HISTORY Changes from Revision B (March 2013) to Revision C * 8 Page Changed layout of National Data Sheet to TI format ............................................................................................................ 7 Submit Documentation Feedback Copyright (c) 1995-2013, Texas Instruments Incorporated Product Folder Links: MM5452 MM5453 PACKAGE OPTION ADDENDUM www.ti.com 21-Dec-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty MM5452N/NOPB LIFEBUY PDIP NFJ 40 9 Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 85 MM5452N (4/5) MM5452V LIFEBUY PLCC FN 44 25 TBD Call TI Call TI -40 to 85 MM5452V MM5452V/NOPB ACTIVE PLCC FN 44 25 Green (RoHS & no Sb/Br) CU SN Level-3-245C-168 HR -40 to 85 MM5452V MM5452VX/NOPB ACTIVE PLCC FN 44 500 Green (RoHS & no Sb/Br) CU SN Level-3-245C-168 HR -40 to 85 MM5452V MM5453N LIFEBUY PDIP NFJ 40 9 TBD Call TI Call TI -40 to 85 MM5453N MM5453N/NOPB LIFEBUY PDIP NFJ 40 9 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 85 MM5453N MM5453V/NOPB ACTIVE PLCC FN 44 25 Green (RoHS & no Sb/Br) CU SN Level-3-245C-168 HR -40 to 85 MM5453V MM5453VX/NOPB ACTIVE PLCC FN 44 500 Green (RoHS & no Sb/Br) CU SN Level-3-245C-168 HR -40 to 85 MM5453V (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 21-Dec-2017 (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 MECHANICAL DATA NFJ0040A N0040A N40A (Rev E) www.ti.com PACKAGE OUTLINE FN0044A PLCC - 4.57 mm max height SCALE 0.800 PLASTIC CHIP CARRIER B .180 MAX [4.57] .650-.656 [16.51-16.66] NOTE 3 A 6 1 44 (.008) [0.2] 40 7 .020 MIN [0.51] 39 PIN 1 ID (OPTIONAL) .650-.656 [16.51-16.66] NOTE 3 .582-.638 [14.79-16.20] 17 29 18 28 .090-.120 TYP [2.29-3.04] 44X .026-.032 [0.66-0.81] C SEATING PLANE 44X .013-.021 [0.33-0.53] .007 [0.18] C A B 40X .050 [1.27] .004 [0.1] C .685-.695 [17.40-17.65] TYP 4215154/A 04/2017 NOTES: 1. All linear dimensions are in inches. Any dimensions in brackets are in millimeters. Any dimensions in parenthesis are for reference only. Controlling dimensions are in inches. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Dimension does not include mold protrusion. Maximum allowable mold protrusion .01 in [0.25 mm] per side. 4. Reference JEDEC registration MS-018. www.ti.com EXAMPLE BOARD LAYOUT FN0044A PLCC - 4.57 mm max height PLASTIC CHIP CARRIER SYMM 44X (.093 ) [2.35] 1 6 44 40 7 39 44X (.030 ) [0.75] SYMM (.64 ) [16.2] 40X (.050 ) [1.27] 29 17 (R.002 ) TYP [0.05] 18 28 (.64 ) [16.2] LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:4X EXPOSED METAL .002 MAX [0.05] ALL AROUND METAL SOLDER MASK OPENING .002 MIN [0.05] ALL AROUND EXPOSED METAL METAL UNDER SOLDER MASK SOLDER MASK OPENING NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK DEFINED SOLDER MASK DETAILS 4215154/A 04/2017 NOTES: (continued) 5. Publication IPC-7351 may have alternate designs. 6. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN FN0044A PLCC - 4.57 mm max height PLASTIC CHIP CARRIER SYMM 44X (.093 ) [2.35] 6 1 44 40 7 39 44X (.030 ) [0.75] SYMM (.64 ) [16.2] 40X (.050 ) [1.27] 29 17 (R.002 ) TYP [0.05] 18 28 (.64 ) [16.2] SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:4X 4215154/A 04/2017 NOTES: (continued) 7. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 8. Board assembly site may have different recommendations for stencil design. www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2017, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: MM5453N MM5453N/NOPB MM5453V MM5453V/NOPB MM5453VX MM5453VX/NOPB